Hitachi KP-F80 User manual

KP
-F80
Progressive Scan
B/W CCD Camera
Operation Guide

Table of Contents
KP-F80
1. General 1
･･･････････････････････････････････････････････
･･･････････････････････････････････････････
･･････････････････････････････････････････
････････････････････････････････････････････
･･･････････････････････････････････････････
･･････････････････････････････････････････
･･････････････････････････････････････････
････････････････････････････････････････
･････････････････････････････････････････
･･･････････････････････････････････････････････
･････････････････････････････････････････
････････････
2. Composition 1
3. Specifications 1
4. Adjustment 3
5. Timing chart 5
6. External view 9
7. External sync 10
8. Connect cables 11
9. Optical system 12
10. Optional 13
11. Notes to users 16
Attachment ：Spectral sensitivity characteristic 18

KP-F80
1

1. General
The Hitachi KP-F80 are a high performance self-contained black and white CCD camera suited
for a wide variety of general purpose and specialized applications. The charge coupled
device (CCD) imaging element is 1/3-inch size progressive scanning with independent readout
of all picture elements (pixels).
In addition to high resolution and sensitivity, a broad array of functions, including multi-step
electronic shutter, HD/VD external sync, frame on demand and many more contribute to
versatility that meets a wide range of needs.
The square pixel CCD also renders an image appropriate for image processing systems.

2. Composition

1) Black and white camera (With IR cut filter) 1
･････････
･･･････････････････････････････
2) Operation manual 1



3. Specifications

1) Imaging device 1/3 inch progressive scan interline CCD
Total pixels 1077(H)×788(V)
Effective pixels 1034(H)×779(V)
Pixel size 4.65(H)×4.65(v)µm
2) Sensing area 4.81(H)×3.62(V)mm
3) Scanning system Progressive scan
4) Hor. scanning frequency 23.622kHz
5) Vert. scanning frequency 29.83 Hz
6) Sync system Internal/external, automatic selection
7) External sync input HD & VD : 5V DC negative
Input impedance : 75Ωor High impedance
Frequency deviation : ±1%

3.Specifications
KP-F80
2
8) Video output 1.0 Vp-p, 75Ω, unbalanced
Video component : 0.7 Vp-p
Sync component : 0.3 Vp-p negative
9) Horizontal Resolution 800 TV lines
10) Signal to noise ratio 54 dB
11) Electronic shutter External switch settings for off
(standard exposure),
1/50000s to 1/250s
Factory setting is off.
12) Gamma correction 1
13) Gain control Manual gain control.
Factory setting is Minimum.
14) Frame on demand External switch.
Selectable One trigger, fixed shutter and Reset
control. (Partial scan : option)
Factory setting is off.
15) Power supply voltage 12 ±1 VDC
16) Power consumption Approx. 2.2 W
17) Ambient temperature and humidity
Operating -10 to 50℃RH less than 90 %
Storage -20 to 60℃RH less than 70 %
Caution: For continued stable operation, the camera should be used under 40℃or less when
it is used continuously for extended period of time.
18) Anti-vibration 98m/s2(10 to 60Hz, amplitude: 0.98mm constant,
60 to 200Hz, amplitude: variable)
(10 to 200Hz, sweep:1 min., XYZ, 30 min.)
19) Resistance to shock 686m/s2(Drop test, once each top, bottom,
left and right)
20) Dimensions 29(W)
×29(H) ×38.5(L)mm
21) Mass 55g approx.

4. Adjustment
KP-F80
3
HD/VD IN/OUT
OUT IN
IN .... External HD/VD Input
OUT.. Internal HD/VD Output
TERMINATION
HIGH 75ohm
INPUT IMPEDANCE
EXTERNAL HD AND
EXTERNAL VD
FRAME ON DEMAND
E.SHUTTER
SHUT
SCAN
MODE
H.TERM
V.TERM
ONE
TRIGGER
MODE FIXED
SHUTTER
TRIGGER
RESET
CONTROL
PARTIAL
SCAN
TRIGGER
(OPTION)
GAIN control
MIN MAX
1
2
3
4
5
6
7
8
9
0
Normal
1/250s
1/500s
1/1000s
1/2000s
1/4000s
1/10000s
1/50000s

4.Adjustment
KP-F80
4
VIDEO OUT/DC IN/SYNC CN
VIDEO OUTPUT
DC IN: DC12V(11 to 13V)
EXT.HD, EXT.VD and
Trigger input
External sync mode
ONE trigger Fixed shutter
HD/VD
Internal
sync
mode
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
GND
+12V
GND(Vout)
Vout
GND
-
-
GND
NC
WEN
-
GND
GND
+12V
GND(Vout)
Vout
GND(HD)
HD IN/OUT
VD IN/OUT
GND
NC
WEN
-
GND(VD)
GND
+12V
GND(Vout)
Vout
GND(HD)
HD IN/OUT
Trigger
GND
NC
WEN
-
GND(Trig)
GND
+12V
GND(Vout)
Vout
GND(HD)
HD IN/OUT
Trigger
GND
NC
WEN
-
GND(Trig)
GND
+12V
GND(Vout)
Vout
GND(HD)
HD IN/OUT
Trigger/VD
GND
NC
WEN
Trigger B
GND(Trig)
GND
+12V
GND(Vout)
Vout
GND(HD)
(HD IN/OUT)
Trigger
GND
NC
WEN
-
GND(Trig)
Reset control Partial(OPTION)
Frame on demand JU-F30
BNC
(GND)
(+12V)
GND
VIDEO1
(GND)
HD
VD
(GND)
VIDEO2
WEN
-
(GND)



5 Timing chart
KP-F80
5
94
5 40 164 29 3 5 1024 5 40
B1
B40
D1
D29
B1
B3
B1
B40
33.33nsec 1034
H BLK
246 (8.20us)
18
0.60us 60
2.00us 168
5.60us 1024
42.3us
1270
1077
clk=33.33nsec
KP-F80 CCD OUTPUT WAVE TIMING CHART
H Drive
CCD pixel and
Hregister array
CCD output
signal
Composit video
signal
H register
transfar stop
Optically
black Dummy
H register
Photosensing period
Output video period

5 Timing chart
KP-F80
6
11H9H4H
779
778
777
3
2
1
6
5
4
1
7
7
42
24
1H=42.33uS
11
10
9
8
7
6
5
4
3
2
2H
KP-F80 Timming chart
Vertical
Video out
V Drive
BLK
H Drive CCD out WEN out

5 Timing chart
KP-F80
7
Trigger pulse
V.SYNC
Video output
5Vp
p
Low: 0V
High: 5V
Trigger pulse
Integration time
(Shutter switch)
V.SYNC
Video output
5Vp
p
Low: 0V
High: 5V
ONE Trigger
Fixed Shutter
Trigger B pulse
V.SYNC
Video output
5Vp
p
Low: 0V
High: 5V
Reset control
Integration time
*1
Trigger pulse 3H~250ms
*1
*1Please
inquire.
Integration time
*1
2us approx.
2us approx.
2us approx.
KP-F80
Frame on demand function
TriggerBpulse........Asynchronous
Triggerpulse......LatchininternalHD
Triggerpulse........LatchininternalHD
Triggerpulse........Asynchronous
NOTE:Thelatchandnon-latchcanbechanged.
2us approx.
2us or more.
2us approx.
2us or more.

5 Timing chart
KP-F80
8
Trigger B pulse
V.SYNC
Video output
5Vpp
Low: 0V
High: 5V
Reset control
Integration time
*1
Trigger pulse 3H~250ms
*1
1/3s
approx.
Special function of reset control Trigger
The camera shifts to the output of a normal mode (continuous output) when Trigger B signal passes about
1/3 seconds in the state of High.
(The image is output by inputting the Trigger at the VD cycle for this period.)
It returns to the Trigger mode if Trigger B signal becomes Low.
However, after becoming Low Trigger B, the period of 50ms becomes a Trigger signal input prohibition
period.



6 External view



Dimensions



KP-F80
9

7. External sync
KP-F80
1
0

 Horizontal and vertical drive signal inputs
HD f(H) = 23.622 kHz ±1 %
VD f(V) = 29.83 Hz
 Input level
HD 4 to 6 VDC negative
VD 4 to 6 VDC negative
Trigger 4 to 6 VDC
 Input impedance 75ohm or High impedance (10kohm)
Trigger B(Pin 11) 1kohm

























HD
VD
T=1/f(H)
 Vertical drive signal (VD)
 Horizontal drive signal (HD)
Set HD and VD fallings edges to the same phase (0 ±2 µs)
 HD and VD phase relationship
 Drive signal input waveform
A
pprox. 3.1µs
4〜6VDC
A
pprox. 0.4ms
4〜6VDC
T=1/f(V)

8. Connect cables
KP-F80
1
1
Connection of options

9. Optical system
KP-F80
1
2
1)Flange focal
・Image size: 1/3-inch
・The flange focal distance is 17.526mm(in air).
・Flange focal distance cannot be adjusted.
Note:
Select such a lens as the length (A) from the flange surface of the lens to the end of the screw side is
8mm or less.
2) Optical filler
This camera is provided with an IR cut filter.
IR cut filter removal
(3)(2)
(4)
(1)
a) Remove two screws (1) shown in Fig., and filter holder (2) will come off.
b) Remove the IR cut filter (3) from filter frame (4).
c) Reinstall and secure filter holder (2) with two screws (1).
Caution
Prior to removing the optical filter, be sure to turn off the power.
IR cut filter IRC650
Dimensions: 14 x 12 x 1.0t
Part code: XMD0006
* The flange focal point shortens by about 0.3mm when IR cutting filter is removed.
We will recommend the dummy glass of the optional to be installed.

10. Optional


1)Tripod adaptor TA-F30 (23885AX)
2)12-pin plug HR10A-10P-12S(01) Product code: 23810AX
1
2
34567
8
9
10
12
11
Viewedfromthisside
KP-F80
13

10. Optional
3)Junction box JU-F30 Product code: 23884AX
4)Dummy glass ARC1214 Parts code: XMD0009
5)Camera cables
Mould type Assy type Shielded type
2m C-201KSM(23861AX) C-201KS(23856AX) C-201KSS(23872AX)
5m C-501KSM(23862AX) C-501KS(23857AX) C-501KSS(23873AX)
10m C-102KSM(23863AX) C-102KS(23858AX) C-102KSS(23874AX)
Specify assembly or shielded type at time of order.
(): Product code
We will recommend the camera cable of the shield type when using it in the sphere of CE.
KP-F80
14

10. Optional
KP-F80
15
・Voltage drop due to a cable is about 0.01V per meter.
・The H phase delays by about 5ns per meter.
・Attenuation of video signal due to used cable
Attenuation due to optional cables C-501KSM and C-102KSM is shown below.
Attenuation is proportionate to the cable length.
Characteristic impedance is kept at constant even at cable length change.


1
2
3
4567
8
9
10
12
11
(RED) WHT YEL (ORN)
(
WHT
)
(BLK)
BRN
GRY
BLU
YEL
YEL
WHT
Cable
length
Attenuation at 4MHz
50dB/Km
Attenuation at 7MHz
70dB/Km
Attenuation at 12MHz
90dB/Km
1m 0.05 0.07 0.09
2m 0.1 0.14 0.18
5m 0.25 0.35 0.45
Attenuation due
to cable length(dB)
10m 0.5 0.7 0.9
The video bandwidth obtained by the KP-F80 is up to approximately 12.5 MHz.


11. Notes to users
KP-F80
16
 Power supply
 Connect a 12V DC voltage (11 to 13V) from an external regulated DC power supply.
 Use a stable power supply without ripple and noise.
 Prior to turning on the power switch , check that the polarities of the power cable are
correct , referring to the connection diagram 


To protect CCD (sensor)
 Do not touch the glass surface of the CCD sensor to avoid deterioration in picture
quality due to dirt and scratches.
 If the glass surface of the sensor should become dusty or dirty , remove dust or dirt
carefully with a cotton-tipped applicator. Do not wipe the surface with dry cloth or
paper tissue to avoid possible damage to the glass surface by static electricity.


Protection of camera
 Do not use or store the camera under direct sunlight , at a place exposed to rain or
snow , or at a place where flammable or corrosive gas is present.
 When housing the camera in a camera case , use the utmost care regarding rise of
internal temperature.
When casing the camera , the temperature normally rises by 10 to 20℃, compared
with the outside air temperature. The camera operates in the temperature range from
-5 to 45℃. If the camera is used or left in high temperature environment for hours ,
the life of the camera may be shortened.
 Do not drop the camera. Do not apply strong shock or vibration to the camera.
 Before connecting or disconnecting a connector , turn off the camera and be sure to
hold connector body to connect or disconnect the connector.


Camera arrangement 
 Mutual interference noise can occur if multiple cameras are arranged in close proximity.
Separate the cameras to the extent possible.
When camera units are installed directly into other equipment , external noise can
prevent a normal picture. In such cases , shield the camera units.
The camera can be damaged by static electricity. Use ample care when installing
and arranging.


Auto electric shutter 
 In regions using 50 Hz power line frequency , flicker can appear on the monitor screen
from light sources such as fluorescent or mercury. In such cases , release the auto
electronic shutter.


11. Notes to users
KP-F80
17


Phenomena inherent to CCD imaging device 
Following are phenomena inherent to a CCD imaging device , and not defects.
 Smear and blooming
When strong light (lamp , fluorescent lamp , reflected light , etc.) is shot , pale bands
are displayed vertically above and below the light.
In this case , change the angle of the camera so that such strong light does not enter
the camera through the lens.






 Fixed pattern noise 
When the camera is operated in a high temperature , fixed pattern noise may appear
on the entire screen.
The higher the sensitivity of camera , the more this fixed pattern noise appears.

 Moire
When fine patterns are shot , moire may be displayed.

 The CE mark is required when exporting to Europe. Obtain the necessary
authorization for the customer’s system. Enclose the camera in a shielded case and
use shielded cable.



Spectral sensitivity (typical example)

KP-F80
18