Hiyasu ASH09UI-LE User manual

OPERATING MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE FUNCIONAMIENTO
MANUALE DI ISTRUZIONI
ΕΓΧΕΙΡΙΔΙΟ ΛΕΙΤΟΥΡΓΙΑΣ
MANUAL DE INSTRUÇÕES
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
KULLANIM KILAVUZU
P/N9332428001
AIR CONDITIONER
Compact Wall Mounted Type
s
ê
u
g
u
tr
o
Pάk
I
vηλ
λ
Eonailat
Iloñ
a
p
sE s
i
açn
a
rFh
cstueDh
s
ilgn
E
KEEP THIS MANUAL FOR FUTURE REFERENCE
DIESE ANLEITUNG BITTE SORGFÄLTIG AUFBEWAHREN
CONSERVEZ CE MODE D’EMPLOI AFIN DE POUVOIR VOUS Y RÉFÉRER ULTÉRIEUREMENT
GUARDE ESTE MANUAL PARA PODERLO CONSULTAR EN EL FUTURO
CONSERVARE QUESTO MANUALE PER OGNI EVENTUALE FUTURO RIFERIMENTO
ΚΡΑΤΗΣΤΕ ΤΟ ΕΓΧΕΙΡΙΔΙΟ ΓΙΑ ΜΕΛΛΟΝΤΙΚΗ ΑΝΑΦΟΡΑ
GUARDE ESTE MANUAL PARA CONSULTA POSTERIOR
СОХРАНИТЕ НАСТОЯЩЕЕ РУКОВОДСТВО ДЛЯ БУДУЩИХ ССЫЛОК
BU KILAVUZU, DAHA SONRA BAfiVURMAK ÜZERE SAKLAYIN
eç
kr
üTйик
сс
уР
9332428001_OM.indb 19332428001_OM.indb 1 1/7/2011 12:00:18 PM1/7/2011 12:00:18 PM

En-1
SAFETY PRECAUTIONS
●Before using the appliance, read these “PRECAUTIONS” thoroughly and operate in the correct way.
●The instructions in this section all relate to safety; be sure to maintain safe operating conditions.
●“DANGER”, “WARNING” and “CAUTION” have the following meanings in these instructions:
DANGER! This mark indicates procedures which, if improperly performed, are most likely to
result in the death or serious injury to the user or service personnel.
WARNING! This mark indicates procedures which, if improperly performed, might lead to the
death or serious injury of the user or service personnel.
CAUTION! This mark indicates procedures which, if improperly performed, might possibly result
in personal harm to the user, or damage to property.
●Do not attempt to install this air conditioner by yourself.
●This air conditioner contains no user-serviceable parts. Always consult authorized service personnel for
repairs.
●When moving, consult authorized service personnel for disconnection and installation of the air condi-
tioner.
●
Do not become excessively chilled by staying for many hours in the direct cooling airflow.
●Do not insert fingers or objects into the outlet port or intake grille.
●Do not start and stop air conditioner operation by disconnecting the power supply cord.
●Take care not to damage the power supply cord.
●
If the power supply cord of this appliance is damaged, it should only be replaced by the authorized service
personal, since special purpose tools and specified cord are required.
●In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the breaker, and
consult authorized service personnel.
●In the event of refrigerant leakage, be sure to keep away from fire or any flammables. (consult an autho-
rized service personnel)
●Provide occasional ventilation during use.
●Do not direct airflow at fireplaces or heating apparatus.
●Do not climb on, or place objects on, the air conditioner.
●Do not hang objects from the indoor unit.
●Do not set flower vases or water containers on top of air conditioners.
●Do not expose the air conditioner directly to water.
●Do not operate the air conditioner with wet hands.
●Do not pull power supply cord.
●Turn off power supply when not using the indoor unit for extended periods.
●Check the condition of the installation stand for damage.
●Do not place animals or plants in the direct path of the airflow.
●Do not drink the water drained from the air conditioner.
●Do not use in applications involving the storage of foods, plants or animals, precision equipment, or art
works.
●Connection valves become hot during Heating; handle with care.
●Do not apply any heavy pressure to radiator fins.
DANGER!
CAUTION!
P/N9332428001
CONTENTS
SAFETY PRECAUTIONS......................................En-1
FEATURES AND FUNCTIONS .............................En-2
NAME OF PARTS .................................................En-3
PREPARATION .....................................................En-5
OPERATION..........................................................En-6
POWERFUL OPERATION ....................................En-8
ECONOMY OPERATION......................................En-8
TIMER OPERATION .............................................En-9
SLEEP TIMER OPERATION...............................En-10
ADJUSTING THE DIRECTION OF
AIR CIRCULATION .............................................En-11
SWING OPERATION ..........................................En-11
10 °C HEAT OPERATION ...................................En-12
MANUAL AUTO OPERATION.............................En-12
OUTDOOR UNIT LOW NOISE OPERATION .....En-12
CLEANING AND CARE.......................................En-13
TROUBLESHOOTING ........................................En-15
OPERATING TIPS...............................................En-16
AIR CONDITIONER
Compact Wall Mounted Type OPERATING MANUAL
9332428001_OM.indb 19332428001_OM.indb 1 1/7/2011 12:00:35 PM1/7/2011 12:00:35 PM

En-2
POWERFUL OPERATION
Used for quickly cooling or heating the room.
■Clean function
REMOVABLE INTAKE GRILLE
The indoor unit's Intake Grille can be removed for easy clean-
ing and maintenance.
MILDEW-RESISTANT FILTER
The AIR FILTER has been treated to resist mildew growth,
thus allowing cleaner use and easier care.
POLYPHENOL CATECHIN AIR CLEANING FILTER
The polyphenol catechin air cleaning filter uses static electric-
ity to clean fine particles and dust in the air such as tobacco
smoke and plant pollen that are too small to see. The filter
contains catechin, which is highly effective against various
bacteria by suppressing the growth of the bacteria adsorbed to
the filter.
Note that when the air cleaning filter is installed, the amount
of air produced decreases, causing a slight decrease in the
indoor unit's performance.
NEGATIVE AIR IONS DEODORIZING FILTER
It comprises pottery super micro particles which can produce
negative air ions having the effect of deodorizing and can ab-
sorb and remit the peculiar smell at home.
■Remote controller
WIRELESS REMOTE CONTROLLER
The Wireless Remote Controller allows convenient control of
indoor unit operation.
■Energy saving and Comfortable function
INVERTER
At the start of operation, large amount of power is used to
bring the room quickly to the desired temperature. Afterward,
the air conditioner automatically switches to a low power set-
ting for economic and comfortable operation.
ECONOMY OPERATION
When ECONOMY operation mode is operated, the room tem-
perature will be little higher than the set-temp under cooling
mode and lower than set-temp under heating mode. Therefore,
the ECONOMY mode is able to save more energy than other
normal mode.
SWING OPERATION
The Airflow Direction Louvers swings automatically up and
down so that the air speeds to every nook and corner of your
room.
AUTO CHANGEOVER
The operation mode (cooling, dry, heating) is switched auto-
matically to maintain the set temperature, and the temperature
is kept constant at all times.
SUPER QUIET OPERATION
The indoor unit's airflow is reduced to produce quieter operation.
10 °C HEAT OPERATION
The room temperature can be maintained at 10 °C so as to
prevent the room temperature from falling too far.
OUTDOOR UNIT LOW NOISE OPERATION
OUTDOOR UNIT LOW NOISE Operation mode reduces the
noise level of the outdoor unit by suppressing the fan speed
and the rotation number of the compressor. It is effective when
the surrounding area is quiet, such as in the night.
■Convenient function
PROGRAM TIMER
The program timer allows you to integrate OFF timer and ON
timer operations in a single sequence. The sequence can
involve 1 transition from OFF timer to ON timer, or from ON
timer to OFF timer, within a 24 hour period.
SLEEP TIMER
When the SLEEP button is pressed during Heating mode, the
indoor unit's thermostat setting is gradually lowered during the
period of operation; during cooling mode, the thermostat set-
ting is gradually raised during the period of operation. When
the set time is reached, the indoor unit automatically turns off.
FEATURES AND FUNCTIONS
●Operate only with air filters installed.
●Do not block or cover the intake grille and outlet port.
●Ensure that any electronic equipment is at least 3.3ft (1m) away from either the indoor or outdoor units.
●Avoid installing the air conditioner near a fireplace or other heating apparatus.
●
When installing the indoor and outdoor unit, take precautions to prevent access to infants.
●Do not use inflammable gases near the air conditioner.
●This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
CAUTION!
9332428001_OM.indb 29332428001_OM.indb 2 1/7/2011 12:00:36 PM1/7/2011 12:00:36 PM

En-3
Fig. 1
NAME OF PARTS
To facilitate explanation, the accompanying illustra-
tion has been drawn to show all possible indicators; in
actual operation, however, the display will only show
those indicators appropriate to the current operation.
Fig. 6
Fig. 2
Fig. 3
Fig. 4
Fig. 5
9332428001_OM.indb 39332428001_OM.indb 3 1/7/2011 12:00:36 PM1/7/2011 12:00:36 PM

En-4
Fig. 1 Indoor Unit
1Operating Control Panel (Fig. 2)
2MANUAL AUTO button
●When the MANUAL AUTO button is
pressed in for more than 10 seconds, the
forced cooling operation will start.
●The forced cooling operation is used at
the time of installation.
Only for authorized service personnel's
use.
●When the forced cooling operation starts
by any chance, press the START/STOP
button to stop the operation.
●Please press the button at FILTER IN-
DICATOR RESET
3Indicator (Fig. 3)
4Remote Control Signal Receiver
5OPERATION Indicator Lamp (green)
6TIMER Indicator Lamp (orange)
●If the TIMER indicator lamp flashes when
the timer is operating, it indicates that a
fault has occurred with the timer setting
(See Page 17 Auto Restart).
7ECONOMY Indicator Lamp (green)
●ECONOMY indicator lamp lights when
ECONOMY OPERATION and 10 °C HEAT
OPERATION is operating.
8Intake Grille (Fig. 4)
9Front Panel
0Air Filter
AAirflow Direction Louver
BRight-Left Louver
(behind Airflow Direction Louver)
CDrain Hose
Fig. 5 Remote Controller
DSignal Transmitter
E10 °C HEAT button
FMODE button
GECONOMY button
HOUTDOOR UNIT LOW NOISE button
ION TIMER button
JOFF TIMER button
KCLOCK ADJUST button
LPOWERFUL button
MSET TEMP. button ( / )
NSTART/STOP button
OFAN button
PSWING button
QSET button
RSLEEP button
SCANCEL button
TRESET button
USELECT button ( / )
VRemote Controller Display (Fig.6)
WOperation Mode Display
XLOW NOISE MODE Display
YTemperature SET Display
ZTransmit Indicator Display
[FAN Speed Display
\SWING Display
]Clock & TIMER Display
9332428001_OM.indb 49332428001_OM.indb 4 1/7/2011 12:00:38 PM1/7/2011 12:00:38 PM

En-5
Load Batteries (AAA/R03/LR03 ×2)
1Press and slide the battery compartment lid on the
reverse side to open it.
Slide in the direction of the arrow.
2Insert batteries.
Be sure to align the battery polarities ( ) correctly.
3Close the battery compartment lid.
Set the Current time
1Press the CLOCK ADJUST button (Fig. 5 K).
Use the tip of a ball-point pen or other small object to press the button.
2Use the SELECT ( / ) buttons (Fig. 5 U) to adjust
the clock to the current time.
button: Press to advance the time.
button: Press to reverse the time.
(Each time the buttons are pressed, the time will be advanced/reversed in
1-minute increments; hold the buttons depressed to change the time quickly
in 10-minute increments.)
3Press the CLOCK ADJUST button (Fig. 5 K) again.
This completes the time setting and starts the clock.
To Use the Remote Controller
●
The Remote Controller must be pointed at signal receiver (Fig. 3 4) to operate correctly.
●Operating Range: About 7 m.
●When a signal is properly received by the indoor unit, a beeping sound will be heard.
●If no beep is heard, press the Remote Controller button again.
Remote Controller Holder
PREPARATION
CAUTION!
●Take care to prevent infants from acciden-
tally swallowing batteries.
●When not using the Remote Controller for
an extended period, remove the batteries to
avoid possible leakage and damage to the
unit.
●If leaking battery fluid comes in contact
with your skin, eyes, or mouth, immediately
wash with copious amounts of water, and
consult your physician.
●Dead batteries should be removed imme-
diately and disposed of properly, either in a
battery collection receptacle or to the appro-
priate authority.
●Do not attempt to recharge dry batteries.
Never mix new and used batteries, or
batteries of different types.
Batteries should last about 1 year under
normal use. If the Remote Controller's
operating range becomes appreciably
reduced, replace the batteries and press
the RESET button with the tip of a ball-
point pen or other small object.
Please keep the ballpoint etc. straight
and push it lightly.
Please do not push at an angle or with a
strong force.
1 Mount the Holder.
Screws
Turn on the Power
1Turn on the circuit breaker
2 Set the Remote Controller.
Insert
3 To remove the Remote Con-
troller (when use at hand).
Slide up
9332428001_OM.indb 59332428001_OM.indb 5 1/7/2011 12:00:38 PM1/7/2011 12:00:38 PM

En-6
To Select Mode Operation
1Press the START/STOP button (Fig.5 N).
The indoor unit's OPERATION Indicator Lamp (green) (Fig. 3 5) will light.
The air conditioner will start operating.
2Press the MODE button (Fig.5 F) to select the de-
sired mode.
Each time the button is pressed, the mode will change in the following order.
AUTO COOL DRY
HEAT FAN
About 3 seconds later, the entire display will reappear.
To Set the Thermostat
Press the SET TEMP. button (Fig. 5 M).
button: Press to raise the thermostat setting.
button: Press to lower the thermostat setting.
●Thermostat setting range:
AUTO ....................................18-30 °C
Cooling/Dry ...........................18-30 °C
Heating..................................16-30 °C
The thermostat cannot be used to set room temperature during the FAN mode (the tem-
perature will not appear on the Remote Controller's Display).
About 3 seconds later, the entire display will reappear.
The thermostat setting should be considered a standard value, and may differ
somewhat from the actual room temperature.
To Set the Fan Speed
Press the FAN button (Fig. 5 O).
Each time the button is pressed, the fan speed changes in the following order:
(AUTO) (HIGH) (MED) (LOW) (SUPER QUIET)
About 3 seconds later, the entire display will reappear.
When set to AUTO:
Heating
: Fan operates so as to optimally circulate warmed air.
However, the fan will operate at very low speed when the temperature of
the air issued from the indoor unit is low.
Cooling
: As the room temperature approaches that of the thermostat setting, the
fan speed becomes slower.
Fan : The fan runs at the low fan speed.
The fan will operate at a very low setting during Monitor operation and at the start of
the Heating mode.
SUPER QUIET Operation
SUPER QUIET operation begins. The indoor unit's airflow will be reduced for quieter
operation.
●SUPER QUIET operation cannot be used during Dry mode. (The same is true when
dry mode is selected during AUTO mode operation.)
●During Super Quiet operation, Heating and Cooling performance will be reduced
somewhat. If the room does not warm up/cool down when using SUPER QUIET Op-
eration, please adjust the indoor unit's Fan Speed.
OPERATION
Example: When set to COOL.
Example: When set to 26 °C.
Example: When set to AUTO.
▲ ▲ ▲
▼ ▼
9332428001_OM.indb 69332428001_OM.indb 6 1/7/2011 12:00:39 PM1/7/2011 12:00:39 PM

En-7
To Stop Operation
Press the START/STOP button (Fig. 5 N).
The OPERATION Indicator Lamp (green) (Fig. 3 5) will go out.
About AUTO CHANGEOVER Operation
AUTO: ●When AUTO CHANGEOVER operation first selected, the fan will operate
at very low speed for about a few minutes, during which time the indoor
unit detects the room conditions and selects the proper operation mode.
If the difference between thermostat setting and actual room temperature
is more than +2 °C →Cooling or dry operation
If the difference between thermostat setting and actual room temperature
is within ±2 °C →Determined by outdoor temperature
If the difference between thermostat setting and actual room temperature
is more than –2 °C →Heating operation
●When the indoor unit has adjusted your room's temperature to near the
thermostat setting, it will begin monitor operation. In the monitor operation
mode, the fan will operate at low speed. If the room temperature subse-
quently changes, the indoor unit will once again select the appropriate
operation (Heating, Cooling) to adjust the temperature to the value set in
the thermostat.
●
If the mode automatically selected by the indoor unit is not what you wish,
select one of the mode operation (HEAT, COOL, DRY, FAN).
About Mode Operation
Heating: ●Use to warm your room.
●When Heating mode is selected, the indoor unit will operate at very low
fan speed for about 3 to 5 minutes, after which it will switch to the selected
fan setting. This period of time is provided to allow the indoor unit to warm
up before begin full operation.
●When the room temperature is very low, frost may form on the outdoor
unit, and its performance may be reduced. In order to remove such frost,
the air conditioner will automatically enter the defrost cycle from time to
time. During Automatic Defrosting operation, the OPERATION Indicator
Lamp (Fig. 3 5) will flash, and the heat operation will be interrupted.
●After the start of heating operation, it takes some time before the room
gets warmer.
Cooling: ●Use to cool your room.
Dry: ●Use for gently cooling while dehumidifying your room.
●You cannot heat the room during Dry mode.
●During Dry mode, the indoor unit will operate at low speed; in order to ad-
just room humidity, the indoor unit's fan may stop from time to time. Also,
the fan may operate at very low speed when adjusting room humidity.
●The fan speed cannot be changed manually when Dry mode has been
selected.
Fan: ●Use to circulate the air throughout your room.
During Heating mode:
Set the thermostat to a temperature setting
that is higher than the present room tem-
perature. The Heating mode will not oper-
ate if the thermostat is set lower than the
actual room temperature.
During Cooling/Dry mode:
Set the thermostat to a temperature setting
that is lower than the present room tem-
perature. The Cooling and Dry modes will
not operate if the thermostat is set higher
than the actual room temperature (in Cool-
ing mode, the fan alone will operate).
During Fan mode:
You can not use the indoor unit to heat and
cool your room.
OPERATION
9332428001_OM.indb 79332428001_OM.indb 7 1/7/2011 12:00:40 PM1/7/2011 12:00:40 PM

En-8
POWERFUL OPERATION
Used for quickly cooling or heating the room.
Begin Air Conditioner operation before performing this procedure.
To use POWERFUL Operation
Press the POWERFUL button (Fig. 5 L).
To stop POWERFUL Operation
Press the POWERFUL button (Fig. 5 L) again.
Normal operation begins.
About the POWERFUL Operation
Cooling/Dry
Using the maximum power, it cools the room to the approximate set temperature at one stroke.
● Powerful Operation mode is automatically turned off when the room temperature has fallen to the set temperature or when 20
minutes have passed after setting the POWERFUL Operation mode. However, it does not turn off automatically within a certain
time of setting the POWERFUL Operation mode.
Heating
Using the maximum power, it heats the room to the approximate set temperature at one stroke.
● Powerful Operation mode is automatically turned off when the room temperature has risen to the set temperature or when 20
minutes have passed after setting the POWERFUL Operation mode. However, it does not turn off automatically within a certain
time of setting the POWERFUL Operation mode.
● Wind direction and airflow rate are automatically set in POWERFUL Operation mode. Wind direction can be changed through
the wind direction adjustment button.
● POWERFUL Operation and ECONOMY Operation modes can’t be set simultaneously.
The function whose button on the remote controller is last pressed will be given priority.
● POWERFUL Operation and OUTDOOR UNIT LOW NOISE Operation modes can’ be set simultaneously.
The function whose button on the remote controller is last pressed will be given priority.
ECONOMY OPERATION
Begin Air Conditioner operation before performing this procedure.
To Use the ECONOMY Operation
Press the ECONOMY button (Fig.5 G).
The ECONOMY indicator Lamp (green) (Fig. 3 7) will light.
ECONOMY operation begins.
To Stop the ECONOMY Operation
Press the ECONOMY button (Fig.5 G) again.
The ECONOMY Indicator Lamp (green) (Fig. 3 7) will go out.
Normal operation begins.
About ECONOMY Operation
At the maximum output, ECONOMY Operation is approximately 70% of normal air conditioner operation for cooling and heating.
● If the room is not cooled (or heated) well during ECONOMY operation, select normal operation.
● Once air conditioner operation is stopped. Normal operation begins when the indoor unit is turned on again.
● During the monitor period in the AUTO mode, the air conditioner operation will not change to ECONOMY operation even if
ECONOMY operation is selected by pressing the ECONOMY operation button.
● POWERFUL Operation and ECONOMY Operation modes can’ be set simultaneously.
The function whose button on the remote controller is last pressed will be given priority.
● Indicator Lamp
OPERATION
ECONOMY
TIMER
: Lighting : OFF
9332428001_OM.indb 89332428001_OM.indb 8 1/7/2011 12:00:41 PM1/7/2011 12:00:41 PM

En-9
To Cancel the Timer
Press the CANCEL button.
The air conditioner will return to normal opera-
tion.
To Change the Timer Settings
1. Follow the instructions given in the section “To
Use the ON Timer or OFF Timer” to select
the timer setting you wish to change.
2. Press the ON TIMER button or OFF TIMER
button to select either OFF ON or OFF
ON.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
SUPER QUIET mode), after making the timer
setting and waiting until the entire display
reappears, then press the appropriate buttons
to change the operating condition desired.
Before using the timer function, be sure that the Remote Controller is set to the correct current time (☞P. 5).
To Use the ON timer ( OFF timer ).
1Press the START/STOP button (Fig. 5 N)
(if the indoor unit is already operating, proceed to step 2).
The indoor unit's OPERATION Indicator Lamp (green) (Fig. 3
5
) will light.
2Press the ON TIMER ( OFF TIMER ) button (Fig. 5 I/
Fig. 5 J) .
The indoor unit's TIMER Indicator Lamp (orange) (Fig. 3 6) will light.
3Use the SELECT buttons (Fig. 5 U) to set the desired
ON time ( OFF time ).
Set the time while the time display is flashing (the flashing will continue for
about 5 seconds).
button: Press to advance the time.
button: Press to reverse the time.
About 5 seconds later, the entire display will reappear.
To Use the Program timer
1Press the START/STOP button (Fig. 5 N)
(if the indoor unit is already operating, proceed to step 2).
The indoor unit's OPERATION Indicator Lamp (green) (Fig. 3
5
) will light.
2Press the ON TIMER ( OFF TIMER ) button (Fig. 5 I/
Fig. 5 J) .
The indoor unit's TIMER Indicator Lamp (orange) (Fig. 3 6) will light.
3Use the SELECT buttons (Fig. 5 U) to set the desired
ON time ( OFF time ).
4Press the OFF TIMER ( ON TIMER ) button (Fig. 5 J/
Fig. 5 I) .
5Use the SELECT buttons (Fig. 5 U) to set the desired
OFF time ( ON time ).
The display will alternately show “OFF timer” and “ON timer”, then change to
show the time setting for the operation to occur first.
●The program timer will begin operation. (If the ON timer has been select-
ed to operate first, the indoor unit will stop operating at this point.)
About 5 seconds later, the entire display will reappear.
About the Program timer
●The program timer allows you to integrate OFF timer and ON timer operations in a
single sequence. The sequence can involve 1 transition from OFF timer to ON timer,
or from ON timer to OFF timer, within a 24 hour period.
●The first timer function to operate will be the 1 set nearest to the current time. The
order of operation is indicated by the arrow in the Remote Controller's Display
(OFF →ON, or OFF ←ON).
●One example of Program timer use might be to have the air conditioner automati-
cally stop (OFF timer) the operation after you go to sleep, then start (ON timer) the
operation automatically in the morning before you arise.
TIMER OPERATION
To Cancel the Timer
Press the CANCEL button.
The air conditioner will return to normal operation.
To Change the Timer Settings
Perform steps 2and 3.
To Stop Air Conditioner Operation while
the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
SUPER QUIET mode), after making the timer
setting and waiting until the entire display
reappears, then press the appropriate buttons
to change the operating condition desired.
9332428001_OM.indb 99332428001_OM.indb 9 1/7/2011 12:00:41 PM1/7/2011 12:00:41 PM

En-10
To Cancel the Timer:
Press the CANCEL button.
The air conditioner will return to normal opera-
tion.
To Stop the Air Conditioner During
Timer Operation:
Press the START/STOP button.
SLEEP TIMER OPERATION
Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operation is stopped.
To Use the SLEEP Timer
While the air conditioner is operating or stopped, press the
SLEEP button (Fig. 5 R).
The indoor unit's OPERATION Indicator Lamp (green) (Fig. 3 5) lights and the TIMER
Indicator Lamp (orange) (Fig. 3 6) light.
To Change the Timer Settings
Press the SLEEP button (Fig. 5 R) once again and set the
time using the SELECT ( / ) buttons (Fig. 5 U).
Set the time while the Timer Mode Display is flashing (the flashing will continue about 5
seconds).
button:
▲ ▲ ▲ ▲ ▲ ▲ ▲
0.5H 1H 2H 3H 5H 7H 9H
button:
▲ ▲ ▲ ▲ ▲ ▲ ▲
0.5H7H 5H 3H 2H 1H9H
About 5 seconds later, the entire display will reappear.
About the SLEEP Timer
To prevent excessive warming or cooling during sleep, the SLEEP timer function automatically modifies the thermostat setting in ac-
cordance with the set time setting. When the set time has elapsed, the air conditioner completely stops.
During Cooling/Dry operation:
When the SLEEP timer is set, the thermostat setting is automati-
cally raised 1 °C every 1 hour. When the thermostat setting is
raised a total of 2 °C, the thermostat setting at that time is main-
tained until the set time elapses, at which time the air conditioner
automatically turns off.
SLEEP timer setting
During Heating operation:
When the SLEEP timer is set, the thermostat setting is
automatically lowered 1 °C every 30 minutes. When the thermo-
stat setting is lowered a total of 4 °C, the thermostat setting at
that time is maintained until the set time elapses, at which time
the air conditioner automatically turns off.
SLEEP timer setting
2 °C 3 °C 4 °C
30
minutes
1 °C
1 hour
1 hour
30 minutes
Set time
Set time
1 hour
1 °C 2 °C
9332428001_OM.indb 109332428001_OM.indb 10 1/7/2011 12:00:41 PM1/7/2011 12:00:41 PM

En-11
To select SWING Operation
Press the SWING button (Fig. 5 P).
The SWING Display (Fig. 6 \) will light.
In this mode, the Airflow Direction Louvers will swing automatically to direct the airflow both up and down.
To stop SWING Operation
Press the SWING button (Fig. 5 P) once again.
The SWING Display (Fig. 6 \) will go out.
Airflow direction will return to the setting before swing was begun.
Vertical Air Direction Adjustment
Press the SET button (Fig. 5 Q).
Each time the button is pressed, the air direction range will change as follows:
1
2 3 4 5 6
Types of Airflow Direction Setting:
1, 2, 3, 4, 5, 6 : During Heating/Cooling/Dry modes
The Remote Controller's display does not change.
●Use the air direction adjustments within the ranges shown above.
●The vertical airflow direction is set automatically as shown, in accordance with the
type of operation selected.
During Cooling/Dry mode
: Horizontal flow 1
During Heating mode : Downward flow 6
●During AUTO mode operation, for the first a few minutes after beginning operation,
airflow will be horizontal 1; the air direction cannot be adjusted during this period.
The airflow direction setting will temporarily become 1 when the temperature of the
airflow is low at the start of the Heating mode.
Right-Left Adjustment
Adjust the Right-Left louvers.
●Move the Right-Left louvers to
adjust airflow in the direction you
prefer.
ADJUSTING THE DIRECTION OF AIR CIRCULATION
Vertical (up-down) direction of airflow is adjusted by pressing the Remote Controller's SET button. Horizontal (right-left) airflow direc-
tion is adjusted manually, by moving the Airflow Direction Louvers.
Whenever making horizontal airflow adjustments, start air conditioner operation and be sure that the vertical air direction louvers are
stopped.
DANGER!
●Never place fingers or foreign objects in-
side the outlet ports, since the internal fan
operates at high speed, and personal injury
could be caused.
●Always use the Remote Controller's
SET button to adjust the vertical airflow
louvers. Attempting to move them man-
ually could result in improper operation;
in this case, stop operation and restart.
The louvers should begin to operate
properly again.
●During use of the Cooling and Dry
modes, do not set the Airflow Direc-
tion Louvers in the Heating range
(4 - 6) for many hours, since water
vapor may condense near the outlet
louvers and drops of water may drip
from the indoor unit. During the Cooling
and Dry modes, if the Airflow Direction
Louvers are left in the heating range for
more than 30 minutes, they will auto-
matically return to position 3.
●When used in a room with infants, chil-
dren, elderly or sick persons, the airflow
direction and room temperature should
be considered carefully when making
settings.
CAUTION!
●When adjusting the Right-Left Louvers, it
is necessary to stop the Vertical (up-down)
louvers first and make sure that it stops
completely before adjusting the direction.
1
2
3
4
5
6
Knob (2 places)
Right-Left Louvers
Knob
SWING OPERATION
About Swing Operation
During Cooling/Dry mode : Swings between 1 and 3.(07/09/12 LEC), 1 and 3 .(14 LEC)
During Heating mode : Swings between 3 and 6.(07/09/12 LEC), 4 and 6 .(14 LEC)
●The SWING operation may stop temporarily when the air conditioner’s fan is not operating, or when
operating at very low speeds.
Begin air conditioner operation before performing this procedure.
9332428001_OM.indb 119332428001_OM.indb 11 1/7/2011 12:00:42 PM1/7/2011 12:00:42 PM

En-12
To use the OUTDOOR UNIT LOW NOISE Operation
Press the OUTDOOR UNIT LOW NOISE button (Fig. 5 H).
“LOW NOISE” appears on the Remote Controller display (Fig. 6 X).
To stop the OUTDOOR UNIT LOW NOISE Operation
Press the OUTDOOR UNIT LOW NOISE button (Fig.5 H).
“LOW NOISE” disappears from the Remote Controller display (Fig. 6 X).
Normal operation begins.
MANUAL AUTO OPERATION
OUTDOOR UNIT LOW NOISE OPERATION
Use the MANUAL AUTO operation in the event the Remote Controller is lost or otherwise unavailable.
OUTDOOR UNIT LOW NOISE Operation mode reduces the noise level of the outdoor unit by suppressing the fan speed and the ro-
tation number of the compressor.
It is effective when the surrounding area is quiet, such as in the night.
How To Use the Main Unit Controls
Press the MANUAL AUTO button (Fig. 2 2) more than 3 sec-
onds and less than 10 seconds on the main unit control panel.
To stop operation, press the MANUAL AUTO button (Fig. 2 2) for 3 seconds.
●When the air conditioner is operated
by the controls on the MANUAL AUTO
button, it will operate under the same
mode as the AUTO mode selected on
the Remote Controller (see page 7).
●The fan speed selected will be “AUTO”
and the thermostat setting will be stan-
dard (24 °C).
10 °C HEAT OPERATION
The room temperature can be maintained at 10 °C by pressing the 10 °C. HEAT button
(Fig.5 E) so as to prevent the room temperature from falling too far.
To use 10 °C HEAT OPERATION
Press the 10 °C. HEAT button (Fig.5 E)
The ECONOMY indicator lamp (green) (Fig. 3 7) will light.
To stop 10 °C HEAT OPERATION
Press the START/STOP button (Fig.5 N)
The ECONOMY indicator lamp (green) (Fig. 3 7) will go out.
Then the operation stops.
About the 10 °C HEAT Operation
The Heating mode will not operate if the room temperature is high enough.
While 10 °C HEAT OPERATION is in
progress, only the following operation
can be used.
• SET
● Indicator Lamp
OPERATION
ECONOMY
TIMER
: Lighting : OFF
About OUTDOOR UNIT LOW NOISE Operation
•OUTDOOR UNIT LOW NOISE Operation mode can be used during cooling, dry, heating and automatic operation. It can not be
used in FAN and DRY mode.
• OUTDOOR UNIT LOW NOISE Operation setting is saved even if the air-conditioned is stopped. Display on the remote control is
also retained.
• When the fan speed and the rotation number of the compressor of the outdoor unit have sufficiently reduced, OUTDOOR UNIT
LOW NOISE Operation mode does not further reduce the fan speed and the rotation number of the compressor.
•POWERFUL Operation and OUTDOOR UNIT LOW NOISE Operation modes can’ be set simultaneously.
The function whose button on the remote controller is last pressed will be given priority.
9332428001_OM.indb 129332428001_OM.indb 12 1/7/2011 12:00:43 PM1/7/2011 12:00:43 PM

En-13
CLEANING AND CARE
●Before cleaning the indoor unit, be sure to turn it off and disconnect the Power Supply Cord.
●Be sure the Intake Grille (Fig. 1 8) is installed securely.
●When removing or replacing the air filters, be sure not to touch the heat exchanger, as personal injury
may result.
CAUTION!
Cleaning the Intake Grille
1. Remove the Intake Grille.
1 Place your fingers at both lower ends of the grille panel,
and lift forward; if the grille seems to catch partway
through its movement, continue lifting upward to re-
move.
2 Pull past the intermediate catch and open the Intake
Grille wide so that it become horizontal.
2. Clean with water.
Remove dust with a vacuum cleaner; wipe the indoor unit
with warm water, then dry with a clean, soft cloth.
3. Replace the Intake Grille.
1 Pull the knobs all the way.
2 Hold the grille horizontal and set the left and right
mounting shafts into the bearings at the top of the panel.
3 Press the place where the arrow on the diagram indi-
cates and close the Intake Grille.
Cleaning the Air Filter
1. Open the Intake Grille, and remove the
air filter.
Lift up the air filter's handle, disconnect the 2 lower tabs,
and pull out.
2. Remove dust with a vacuum cleaner or
by washing.
After washing, allow to dry thoroughly in a shaded place.
3. Replace the Air Filter and close the In-
take Grille.
1 Align the sides of the air filter with the panel, and push
in fully, making sure the 2 lower tabs are returned prop-
erly to their holes in the panel.
2 Close the Intake Grille.
(For purposes of example, the illustration shows the indoor
unit without Intake Grille installed.)
●Dust can be cleaned from the air filter either with a vacuum
cleaner, or by washing the filter in a solution of neutral de-
tergent and warm water. If you wash the filter, be sure to al-
low it to dry thoroughly in a shady place before reinstalling.
●
If dust is allowed to accumulate on the air filter, airflow will be re-
duced, lowering operating efficiency and increasing noise.
●During periods of normal use, the Air Filters should be
cleaned every 2 weeks.
●Don't operate the air conditioner with being opened the in-
take grille.
●When used for extended periods, the indoor unit may accumulate dust inside, reducing its performance. We recommend that
the indoor unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized ser-
vice personnel.
●When cleaning the indoor unit's body, do not use water hotter than 40 °C, harsh abrasive cleansers, or volatile agents like ben-
zene or thinner.
●Do not expose the indoor unit's body to liquid insecticides or hairsprays.
●When shutting down the indoor unit for 1 month or more, first allow the fan mode to operate continuously for half a day to allow
internal parts to dry thoroughly.
Intake Grille
Air filter handle
Air filter (Right & Left)
Mounting
shaft
Bearing
Knob
Mounting
shaft
Knob
1
2
31
2
3
Hooks (2 places)
Hooks (2 places)
9332428001_OM.indb 139332428001_OM.indb 13 1/7/2011 12:00:43 PM1/7/2011 12:00:43 PM

En-14
Air Cleaning Filter Installation
1. Open the Intake Grille and remove the Air
filters.
2. Attach the air cleaning filter to the frame
of the front panel.
●Attach the filter on the inside of the tabs (6 places) so as
not to stick out.
(In the above figure, the intake grille is omitted for the
explanation)
3. Install the 2 Air filters and close the
Intake Grille.
●Don't operate the air conditioner with being opened the
intake grille.
●When air cleaning filters are used, the effect will increased
by setting the fan speed to “High”.
3. Replace them by 2 new Air cleaning
filters.
1Remove the old air cleaning filters in reverse order of
their installation.
2Install in the same way as for installation of the air
cleaning filter set.
4. Install the 2 Air filters and close the
Intake Grille.
● Don't operate the air conditioner with being opened the
intake grille.
About the Air Cleaning Filters
POLYPHENOL CATECHIN AIR CLEANING FILTER (1 sheet)
●The Air Cleaning Filters are disposable filters. (They can not
be washed and reused.)
●For storage of the Air Cleaning Filters, use the filters as
soon as possible after opening the package.
(The air cleaning effect decreases when the filters are left in
the opened package)
●Generally, the filters should be exchanged about every 3
months.
Please buy delicated air cleaning filters (UTR-FA16) (Sold
separately) to exchange the used dirty air cleaning filter.
[Negative air ions deodorizing filter (1 sheet) — light blue]
●The filter should be exchanged about every 3 years so as
to maintain the deodorizing effect.
●Filter frame is not a one-off product.
Please buy delicated deodorizing filter (UTR-FA16-2) (Sold
separately) when exchanging the filter.
Maintenance of Deodorizing Filters
In order to maintain the deodorizing effect, please clean the
filter in the follow way once 3 months.
1Remove the deodorizing filter.
2Clean with water and dry in the air.
1) Flush the filter with high-pressure hot water until the
surface of the filter is covered with water. Please
flush with diluent neutral detergent.
Never wash by reaming or rubbing, otherwise it
will damage the deodorizing effect.
2) Rinse with water flow.
3) Dry in shade.
3Reinstall the deodorizing filter.
CLEANING AND CARE
Replacing dirty Air cleaning filters
Replace filters with the following components (purchased sep-
arately).
●
POLYPHENOL CATECHIN AIR CLEANING FILTER : UTR-FA16
●Negative air ions deodorizing filter: UTR-FA16-2
1. Open the Intake Grille and remove the Air
filters.
2. Remove the air cleaning filters attached
to the frames of the front panel.
Air cleaning filter frame
Tabs (6 places)
Tabs
(6 places)
Air Clean-
ing Filter
Air Cleaning Filter
Air cleaning filter frame
Filter Indicator Reset (The special setting)
Can be used if set correctly during installation.
Please consult authorized serviceman when using this function.
• It lights on when it is time to clean the air filters.
Clean the filter referring to “CLEANING AND CARE”.
After cleaning, press the MANUAL AUTO button (Fig.2 2)
for 2 seconds or less on the indoor unit.
●Indicator Lamp
OPERATION
ECONOMY
TIMER
: Flashing : OFF
9332428001_OM.indb 149332428001_OM.indb 14 1/7/2011 12:00:45 PM1/7/2011 12:00:45 PM

En-15
TROUBLESHOOTING
WARNING!
Symptom
Doesn’t operate immedi-
ately:
Noise is heard:
Smells:
Mist or steam is emitted:
Airflow is weak or stops:
Water is produced from the
outdoor unit:
Problem
●If the indoor unit is stopped and then immediately started again, the
compressor will not operate for about 3 minutes, in order to prevent
fuse blowouts.
●
Whenever the electrical breaker is turned off then on again the pro-
tection circuit will operate for about 3 minutes, preventing unit opera-
tion during that period.
●
During operation or immediately after stopping the unit, the sound of
water flowing in the air conditioner’s piping may be heard. Also, noise
may be particularly noticeable for about 2 to 3 minutes after starting
operation (sound of refrigerant flowing).
●During operation, a slight squeaking sound may be heard. This is
the result of minute expansion and contraction of the front panel due
to temperature changes.
●
During Heating operation, a sizzling sound may be heard occasional.
This sound is produced by the Automatic Defrosting operation.
●Some smell may be emitted from the indoor unit. This smell is the
result of room smells (furniture, tobacco, etc.) which have been
taken into the indoor unit.
●During Cooling or Dry operation, a thin mist may be seen emitted
from the indoor unit. This results from the sudden Cooling of room
air by the cool air emitted from the indoor unit, resulting in conden-
sation and misting.
● During Heating operation, the outdoor unit’s fan may stop, and
steam may be seen rising from the unit. This is due to Automatic
Defrosting operation.
● When Heating operation is started, fan speed is temporarily very
low, to allow internal parts to warm up.
● During Heating operation, if the room temperature rises above the
thermostat setting, the outdoor unit will stop, and the indoor unit will
operate at very low fan speed. If you wish to warm the room further,
set the thermostat for a higher setting.
● During Heating operation, the indoor unit will temporarily stop opera-
tion (between 7 and 15 minutes) as the Automatic Defrosting mode
operates. During Automatic Defrosting operation, the OPERATION
Indicator Lamp will flash.
●During Dry mode, the indoor unit will operate at low speed; in order
to adjust room humidity, the indoor unit’s fan may stop from time to
time. Also, the fan may operate at very low speed when adjusting
room humidity.
●
During SUPER QUIET operation, the fan will operate at very low speed.
●In the monitor of AUTO operation, the fan will operate at very low
speed.
● During Heating operation, water may be produced from the outdoor
unit due to Automatic Defrosting operation.
See Page
—
—
16
—
—
16
—
16
7
6
7
16
NORMAL
FUNCTION
In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the electrical
breaker and consult authorized service personnel.
Merely turning off the unit’s power switch will not completely disconnect the unit from the power source.
Always be sure to turn off the electrical breaker to ensure that power is completely off.
Before requesting service, perform the following checks:
9332428001_OM.indb 159332428001_OM.indb 15 1/7/2011 12:00:47 PM1/7/2011 12:00:47 PM

En-16
TROUBLESHOOTING
Symptom
Doesn’t operate at all:
Poor Cooling (or Heating)
performance:
The unit operates
differently from the Remote
Controller’s setting:
See Page
—
9 - 10
—
6
5
CHECK ONCE
MORE
Items to check
●Has the circuit breaker been turn off?
●Has there been a power failure?
●Has a fuse blown out, or a circuit breaker been tripped?
●Is the timer operating?
●Is the Air Filter dirty?
●Are the air conditioner’s intake grille or outlet port blocked?
●Did you adjust the room temperature settings (thermostat) correctly?
●Is there a window or door open?
●In the case of Cooling operation, is a window allowing bright sunlight
to enter? (Close the curtains.)
●In the case of Cooling operation, are there heating apparatus and
computers inside the room, or are there too many people in the
room?
●Is the unit set for SUPER QUIET operation?
●Is the set for OUTDOOR UNIT LOW NOISE operation?
●Are the Remote Controller’s batteries dead?
●Are the Remote Controller’s batteries loaded properly?
OPERATING TIPS
If the problem persists after performing these checks, or if you notice burning smells, or the OPERATION Indicator Lamp (Fig. 3 5)
and the TIMER Indicator Lamp (Fig. 3 6) flashes, and ECONOMY Indicator Lamp (Fig.3 7) flashes fast. Immediately stop opera-
tion, turn off the electrical breaker and consult authorized service personnel.
Operation and Performance
Heating Performance
●This air conditioner operates on the heat-pump principle,
absorbing heat from outdoor air and transferring that heat
to indoor unit. As a result, the operating performance is
reduced as outdoor air temperature drops. If you feel that
insufficient heating performance is being produced, we
recommend you use this air conditioner in conjunction with
another kind of heating appliance.
●Heat-pump air conditioners heat your entire room by recir-
culating air throughout the room, with the result that some
time may be required after first starting the air conditioner
until the room is heated.
Microcomputer-controlled Automatic Defrosting
●When using the Heating mode under conditions of low out-
door temperature and high humidity, frost may form on the
outdoor unit, resulting in reduced operating performance.
In order to prevent this kind of reduced performance, this
air conditioner is equipped with a Microcomputer-controlled
Automatic Defrosting function. If frost forms, the air con-
ditioner will temporarily stop, and the defrosting circuit will
operate briefly (for about 7-15 minutes).
During Automatic Defrosting operation, the OPERATION
Indicator Lamp (green) will flash.
●After heating operation stops, if frost forms on the outdoor
unit, the unit will start Automatic Defrosting operation. At
this time, the outdoor unit will automatically stop after oper-
ating for a few minutes.
AUTO Restart
In Event of Power Interruption
●The power supply to the air conditioner is stopped by a
power interruption. The air conditioner will then restart auto-
matically in its previous mode when the power is restored.
●
If a power interruption occurs during TIMER operation, the tim-
er will be reset and the indoor unit will begin (or stop) operation
at the new time setting. In the event that this kind of timer fault
occurs, the TIMER Indicator Lamp will flash (see Page. 3).
●Use of other electrical appliances (electric shaver, etc.) or
nearby use of a wireless radio transmitter may cause the air
conditioner to malfunction. In this event, temporarily turn off
the circuit breaker, turn it on and then use the Remote Con-
troller to resume operation.
9332428001_OM.indb 169332428001_OM.indb 16 1/7/2011 12:00:47 PM1/7/2011 12:00:47 PM

9332428001_OM.indb 179332428001_OM.indb 17 1/7/2011 12:02:29 PM1/7/2011 12:02:29 PM

9332428001_OM.indb 189332428001_OM.indb 18 1/7/2011 12:02:29 PM1/7/2011 12:02:29 PM

9332428001_OM.indb 199332428001_OM.indb 19 1/7/2011 12:02:29 PM1/7/2011 12:02:29 PM