Hollywood Sport Rider HR1000 User manual

Hollywood Sport Rider version 2
Model HR1000 -2 Bike Hitch Rack
Not to be used on any trailer, fifth
wheel or vehicle being towed by
another vehicle.
Weight Limit 45 lbs/20 kg per
bike -2 bike maximum capacity
Fits both 1 ¼” and 2” hitch
Optional Locking Kits Available
This box should include the following parts:
A,B) wheel trays with straps C) long frame hook D) short frame hook
E) Insert tube F) 2” adapter G) knobs H) frame hook clamps
I) hitch pin bolt J) carriage bolt
K) insert tube bolts
L) locking washer for hitch pin
M) washers for insert tube bolts
N) washer for hitch pin
O) clip for hitch pin bolt
P) main rack assembly
1
Vertical post
Wheel tray
Support tube
Retaining pins (3)
2 front, 1 side

Remove retaining pins, rotate
wheel tray support tubes down,
reinsert retaining pins. Install insert
tube Einto bracket. Align holes on
insert tube with holes on bracket.
Place washers
M
onto
bolts K,install with 17mm
or adjustable wrench.
Tighten bolts securely.
Assemble frame hooks
C
&
D
to frame hook clamp
H
using carriage bolts
J
and knobs
G
.
Be sure hooks are positioned per drawing.
Place LONG hook assembly
C
onto the vertical post, facing the front of the rack. Then place the SHORT hook
assembly Don the insert tube side of the rack.
Assemble the carriage bolts Jand knobs Gto the wheel holders Aand B. Be sure that the knob is on the
“strap side” of the wheel holder.
2

Slide wheel trays onto wheel tray
support tubes as shown.
Place lock washer
L
and washer
N
onto hitch pin
bolt I. Align the holes, insert the bolt and tighten
securely using a ¾” wrench.
15
If your vehicle has a 1
-
1/4” receiver
, simply insert tube
E
of the rack
into the receiver of your vehicle
3

If your vehicle has a 2” receiver, you will need to attach the black “U’ shaped adapter F
. Line up center hole
of the adapter with the hole on the rack’s insert tube E. Place lock washer Land washer N
onto hitch pin bolt
I. Align the holes, insert the bolt and tighten securely using a ¾” wrench.
IMPORTANT!!
After tight
ening the
hitch pin bolt, insert clip Othrough
the hole on the end of the bolt.
To fold down the vertical post, rotate and remove the side-retaining pin as shown.
4

Pre-position the wheel trays to fit the bike’s wheel base (center to center
distance between the wheel axels) such that they are directly beneath each
wheel. To adjust the wheel trays, loosen the knobs and slide along the wheel
holder support tube. Tighten knobs securely.
To fit the first bike (closest to the vehicle) more easily, the vertical post may be
tilted down (away from vehicle). To do this, simply remove the side retaining pin
per fig. 21 to 23. Note: Never fold down main tube with bike(s) mounted. Place
the first bike in the wheel holders, and then rotate the vertical post up. See
figure 24. Handlebars for the first bike should be on the driver’s side of the
vehicle. If carrying two bikes, always load the smaller bike first (position the
smaller bike between the vehicle and vertical post)
Be sure that the hooks are well supported on the bike’s frame and tighten the
knob securely. Use the Velcro strap on the wheel holder as the final step of
installing the bikes on the rack, per Fig. 27B.
Repeat for the outside/second bike with the short hook.
5
To fold the wheel tray tubes up, rotate and remove the front retaining pins, rotate the tube and replace the pins
INSTALLING THE BIKES ON THE RACK:

Double check before driving off
:
Knobs are tight on all four wheel trays and both frame hooks.
All three retaining pins are properly inserted and secure
Wheel straps are fastened
Hitch pin is secure and hitch pin clip is installed
Drive slowly on bumpy or dirt roads
Limited Lifetime Warranty (effective January 1, 2008):
Hollywood Racks will warrant its car racks and accessories
during the time that an original retail purchaser owns the
product subject to the exclusions and limitations of this warranty.
Hollywood Racks will remedy defects in materials and
workmanship by repairing or replacing (at its option) the complete rack or a defective part without charge for labor or parts.
Hollywood Racks may elect (at its option) to issue a refund equal to the purchase price paid for the product.
This warranty does not cover problems caused by normal wear and tear including (but not limited to) weather,
scratches, dents, rust, accidents, unlawful vehicle operation, misuse, abuse, neglect, theft, unauthorized mo
difications, or
unauthorized repair. No warranty is given for defects resulting in incorrect assembly, incorrect installation onto the vehicle,
installation on a “no fit” vehicle, incorrect attachment of bicycles onto the rack, or overloading of the rack’s
weight
restrictions. This warranty terminates if the original retail purchaser transfers the product to any other person.
If a product is believed to be defective, the original retail purchaser should contact either the original retailer or Hollywood
Racks directly at 800-747-4085 or at [email protected]
Disclaimer of Liability: Repair or replacement of a defective product or the issuance of a refund or credit (as
determined by Hollywood Racks) is a purchaser’s exclusive remedy under this warranty
. Damage to a purchaser’s
vehicle, cargo, bicycles and or to any other person is excluded. This warranty is expressly made in lieu of any and all
other express warranties, whether oral or written.
Hollywood Racks shall not be liable for any direct, indirect, consequential, incidental, special, punitive or
any other damages in connection with the purchase, use or handling of this product.
Some states do not allow the exclusion or limitation of consequential or incidental damages and the above limitation
may not apply to you. This warranty gives you specific legal rights and you have other rights, which
vary from state to state.
6
Tips for carrying woman’s bikes and bikes with slanted top tubes
Adjust the wheel trays so that the hook will rest in the bike frame’s top tube and seat tube, as shown in Fig. 28 and 29.
28
29
Hollywood Racks
12812 S. Spring St. Los Angeles, CA 90061
Tel (310) 516-8600 (800) 747-4085 FAX (310)516-8955
www.hollywoodracks.com email: [email protected]
Customer Service Hours: M-F 8:00AM to 3:00 PM PST
Made in Taiwan 022608 Rev B
Table of contents
Other Hollywood Rack & Stand manuals
Popular Rack & Stand manuals by other brands

Victrola
Victrola VA-75 instruction manual

Vivo
Vivo STAND-TV09 instruction manual

MetalTech
MetalTech I-BMSO4TT OPERATIONAL SAFETY AND ASSEMBLY INSTRUCTIONS

Exhibitor's Handbook
Exhibitor's Handbook Formulate Essential 10ft Arch 07 manual

peerless-AV
peerless-AV LCT620A manual

Sealey
Sealey AP6500 instructions