Holtkamp SunCash User manual

Opterating instruction
SunCash
Money changer and chip card management

Important: For safe and proper use, read the instructions for use and further product-related documents carefully and keep
it for later use!
For errors, technical errors, printing errors and incompleteness, we assume no liability.

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 3 -
Südstraße 40 / D-49084 Osnabrück
[e-mail] /
www.holtkamp.de
Telefon: [phone], Fax: [phone]
Geschäftsführung: Magnus Michael, Uwe Staudinger; Sitz der Gesellschaft: Osnabrück, AG Osnabrück HRB 213567
Banken: Deutsche Bank Osnabrück, IBAN: DE28 2657 0090 0039 5251 00; SW IFT/BIC: DEUTDE3B265
Die Lieferung erfolgt zu unseren Allgemeinen Geschäftsbedingungen mit Stand Juni 2011 nach ZVEI unter Einbeziehung der Softwareklausel
zur Überlassung von Standard-Software als Teil von Lieferungen mit Stand April 2012 nach ZVEI.
Zusätzlich gelten unsere Vertragsbedingungen „Hardware/Schaltplan/Layout“ und „Auftragsfertigung“.
Es gelten unsere Einkaufsbedingungen mit Stand Januar 2018.
EU-Konformitätserklärung / European Union conformity explanation
Für das nachfolgend bezeichnete Erzeugnis / For the following designated product
Geldwechsler und Chipkarten-Management / Money changer and chip card management
SUNCASH
wird hiermit bestätigt, dass die Bauart, in der von uns in Verkehr gebrachten Ausführung, den unten genannten Normen
entspricht.
It is hereby confirmed, that the construction in that execution brought by us in traffic corresponds to the standards specified
down.
Diese Erklärung gilt für alle Geräte, die nach den beiliegenden technischen Unterlagen, welche Bestandteile dieser Erklärung
sind, hergestellt werden.
This explanation applies to all devices, after the enclosed technical documents, which are components of this explanation,
are manufactured.
Einschlägige EG-Richtlinien / Relevant EC guidelines
RoHS-Richtlinie 2011/65/EU / RoHS Directive 2011/65 / EU
1. 2006/95/EG (Niederspannungsrichtlinie)
2006/95/EG (low-voltage guideline)
geändert durch
changed through
2014/35/EU
2. 2004/108/EG (EMV-Richtlinie)
2004/108/EG (EMV guideline)
geändert durch
changed through
2014/30/EU
Angewendete harmonisierte Normen:
Applied one harmonized standards:
EN 60335-1 von 01/2012 (Sicherheit)
EN 60335-1 from 01/2012 (security)
EN 55022 von 12/2011 (Emissionen)
EN 55022 von 12/2011 (emissions)
EN 61000-3, Teil 2 + 3 von (03/2015 und 03/2014) (Emissionen)
EN 61000-3, Teil 2 + 3 von (03/2015 und 03/2014) (emissions)
EN 61000-6, Teil 1 + 2 von (10/2007 und 03/2006) (Immunität)
EN 61000-6, Teil 1 + 2 von (10/2007 und 03/2006) (immunity)
Diese Erklärung ist bindend für den Hersteller
This declaration is binding on the manufacturer
Manfred Holtkamp Elektronik GmbH
Südstraße 40 in 49084 Osnabrück
abgegeben durch:
Signature:
M. Hashemizadeh (EMV-Beauftragter)
..........................................
Osnabrück, den 20.04.2016

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 4 -
Content
1 Legal information......................................................................................................................................................................... 5
2 Warranty ................................................................................................................................................................................5
3 Safety notices .............................................................................................................................................................................. 5
4 Notes on cleaning, maintenance................................................................................................................................................ 5
5 Devicespecicdata .................................................................................................................................................................... 6
6 Generally technical data ............................................................................................................................................................ 6
7 Illustrations ................................................................................................................................................................................7
7.1 Illustration of the device...................................................................................................................................................... 7
7.2 Illustration of the interior ..................................................................................................................................................... 8
7.3 Illustration of the interior of the door................................................................................................................................... 8
8 Specications .............................................................................................................................................................................. 9
9 Installation ..............................................................................................................................................................................10
9.1 Installation notes...............................................................................................................................................................10
9.2 Mounting notes................................................................................................................................................................. 10
9.3 Mounting instruction .........................................................................................................................................................10
9.4 Mounting draft for the electronic multiple coin tester........................................................................................................ 10
9.5 Electrical connection ........................................................................................................................................................ 11
 9.6 Operatingforthersttime............................................................................................................................................... 11
10 Keypad ..............................................................................................................................................................................12
11 Basic functions .......................................................................................................................................................................... 12
11.1 Money changing operating .............................................................................................................................................. 12
11.1.1 Bank note change....................................................................................................................................................... 12
11.1.2 Coin change (only possible with 2. hopper)................................................................................................................ 13
11.2 Chip card sales ...............................................................................................................................................................13
11.3 Revaluing of chip cards ................................................................................................................................................... 13
12 Chip card types.......................................................................................................................................................................... 14
13 Programming .............................................................................................................................................................................14
13.1 Explaning the programming positions ............................................................................................................................. 14
  13.1.1Congurationmenu ................................................................................................................................................... 14
13.1.2 Bonus menu................................................................................................................................................................ 17
13.1.3 Card initialisation menu .............................................................................................................................................. 20
14 Statistics ..............................................................................................................................................................................21
14.1 Explaining the statistic values...........................................................................................................................................21
14.2 Enquiring the statistic values............................................................................................................................................ 22
14.3 Cancelling the statistic values .........................................................................................................................................23
15 Special functions ....................................................................................................................................................................... 24
15.1 Stocktaking function of the hoppers (after removing the cover) ....................................................................................... 24
15.2 Door switch ......................................................................................................................................................................24
16 Device malfunctions ................................................................................................................................................................. 25

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 5 -
1 Legal information
All rights reserved. No part of this manual may not be reproduced
or copied in any form without permission of Holtkamp Elektronik
GmbH. The rights for contained software in control and memory
blocks are exclusively from the manufacturer. The reading and
copying of the program content is strictly prohibited.
The Holtkamp Elektronik GmbH is not liable to the purchaser of
this product or third parties for damages, losses, costs or ex-
penses caused by the buyer or any third party due to accident,
misuse or unauthorized alterations, repairs or improvements.
The Holtkamp Elektronik GmbH shall remain liable for any loss,
costs, disruptions or consequential damages that result from the
use of the control.
The technical data are up to date. Misprints, errors and modi-
cations excepted. Older manuals are no longer valid with the
publication of this manual
4 Notes on cleaning, maintenance
SunCash is more or less maintenance free. By poor coin accep-
tance, the coin runway of the electronic multiple coin tester can
be cleaned free of dust and deposits with a brush or a damp
cloth. The casing can be cleaned with a damp cloth and a solvent
free detergent. Do not at any time, use thinners, petrol, spirits,
acetone or scrubbing cleaning agents. Conventional cleaning
agents could damage the plexiglass window on the laser-cut ed-
ges.
2 Warranty
On the function of the device is granted for a period of 12 months.
The warranty is limited solely to technical defects of the unit, it
can´t be accepted further claims. Further apply our general terms
and conditions, stand of June 2011, for products and services of
the electrical industry (ZVEI) - also see website: www.holtkamp.
de.
Any liability extinguished by the manipulation of the device.
3 Safety notices
The money changer are built according to the prior art and the
recognized safety rules.
Nevertheless, its use threats to life and limb of the user or third
parties, or cause damage to the device or other equipment du-
ring use. Use the device only in perfect condition, and intended,
safety and the risk of danger, in compliance with the instruction
manual! Do immediately eliminate particular disorders, which
maya󰀨ectsafety!Alwayskeeptheoperatinginstructionsdirectly
to the money changer! Note, in addition to the user guide, the ge-
nerally applicable legal and other mandatory regulations relevant
to accident prevention and environmental protection!
Performnochangesand/ormodicationstothemoneychanger
without approval of the manufacturer! Spare parts must meet the
requirementsspeciedbythemanufacturer.Thisisguaranteed
only for original spare parts. Do observe the in the user manual
speciedorprescribeddeadlinesforrecurringmaintenancein-
tervals!
Do provide for the safe and environmentally friendly disposal of
plastic parts and electronic replacement parts! The manufactu-
rer is not liable for damage caused by improper use. The user
bears the risk. Intended use also includes compliance with the
operating instructions and compliance with the inspection and
maintenance conditions.

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 6 -
5 Devicespecicdata
After the operating voltage has been applied, the display will
show for about 2 seconds: Holtkamp SunCash V x.x. It applies
to the description of the software version (X.x). This information
is subject to the technical development of the SunCash and your
order. For later enquiries and orders it would be helpful to know
this information.
Key number (imprinted on key)
Serial number (noted on the model plate)
Commission
Trader
Therefore it is necessary to write these numbers down, which
appear in the display, in the following table for later technical in-
quiries.
6 Generally technical data
Casing material sheet steel (casing 3 mm, door 5 mm)
Casing color RAL 9010 structured in pure white
Color stand/base acrylic, colored backprinted *
Door front 4 VA
Dimension housing h 980 mm x w 695 mm x d 380 mm
Total height 1760 mm
Stand area w 690 mm x d 380 mm
Electrical data 230 V, 50 - 60 Hz
Power absorption 50 VA
Cable entry from above and below
Temperature range 10°C - 40°C
Relative humidity 25 – 70 %
Protection class I by 230V~
Schutzart IP 20
Weight empty (without money) approximately 170 kg
Weight (with money) approximately 223 kg
Fuse board SI 2 315mA T
Attention: Fuses may only be replaced by ones with the
same values!
* Door front available on request in custom design

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 7 -
7 Illustrations
7.1 Illustration of the device
1 2
3
4
5
7
8
9
10
6
1 Banknote slot
2 Coin slot
3 LCD info text display
4 Card slot
5 Keypad
6 Plug lock
7 Cover folding
8 Folding handle
9 Chip card issuance
10 Coin issue
11 Stand
11

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 8 -
7.2 Illustration of the interior 123
3
3
4
5
6
7
9
10
11
1 RESET button for chip card dispenser
2 Fuse 315 mAT/2AT
3 Mounting holes
4 Electronic multiple banknote reader
5 Funnel to mixed coins, cash box
6 Coin hopper 1
7 Coin hopper 2
8 IEC connector 230 V connection
9 Power switch
10 Lock for cash drawer
11 Cash drawer
Standard optional
7.3 Illustration of the interior of the door
12
3
4
5
1 Circuit board
2 Chip card contact unit
3 Elektronic multiple coin tester
4 Tamper protection
5 Chip card dispenser

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 9 -
8 Specications
SUNCASH
Change banknotes into coins
Change coins into coins
Selling chip cards
Revalue chip cards
Banknote reader and stacker
Elektronic multiple coin tester
Coin hopper for coins / token, diameter = 21-31 mm
(max. 900 coins)
2. Coin hopper
Chip card contact unit with ejection magnet
Chip card dispenser (capacity 100 chip cards)
Counter coin issue
Counter accepted coins
Counter accepted banknotes
Counter chip card issue
Counter for debited card amounts
Counter for bonus amounts
Counterforllingdi󰀨erencesofthehopper
Counter for sales
Chip cards see brochure and price list
Token freely programmable by the customer on demand
Standard Optional equipment /
Accessories
Production-technical changes and further developments reser-
ved.

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 10 -
9 Installation
9.1 Installation notes
Through high quality microelectronics SunCash is able to reach
a high standard of reliability. Only if the installation has been pro-
fessionally carried out can the device be guaranteed. During the
installation pay attention to …
● Onlyauthorisedandqualiedelectricianscarryouttheins-
tallation complying with the valid VDE regulations.
●For the electrical connection use only cable of the type
NYM-J 3x1,5 mm².
●The SunCash needs a protective conductor connection.
● Theoorcoveringisantistaticandconductorcapable,to
ensure a minimum of static charge and so reducing the
danger to the electronics.
●the SunCash cannot be operated in the case of damage to
the supply cable or to the SunCash itself.
9.2 Mounting notes
● TheSunCashisastandingdevice.Toassuresu󰀩cientsta-
bility the SunCash must be additionally anchored to a secu-
re wall (no light building bricks). Under the base-plate are
two drilled holes, which allow an additional securing of the
 base-platetotheoor.Thefoot-platecanberemovedby
the four countersunk screws.
●The SunCash must be mounted horizontally and vertically
 level,toguaranteeaawlessfunctionofthecoinreceiver
and mechanical door latch. That means the inclination
angle of the device can only be maximal 2°, forwards or
backwards as well as to the right or to the left.
9.3 Mounting instruction
●The SunCash is conforms to protection type IP 20 and may
only be used in dry rooms.
●The SunCash should be mounted with the help of a water
level.
The angle of inclination may be a maximum of 2°only.
With the door wide open mark the 4 drilled holes, which
are shown under position 2.2 with the number 3
●Drill the Ø12 mm holes and insert suitable dowels. Fit the
electrical supply cable through the appropriate holes, un-
der position 2.2 number 8. The SunCash can then, with
 theappropriatescrews,besecuredrmly.SunCashisme-
 anttobemountedtolimestonewallsorcementedoors.
 Withallothertypesofwalls/oors,themountingmethod
must be strengthened. Light building bricks are not suitable
for clamp SunCash.

9.4 Mounting draft for the electronic multiple
coin tester
Installation and removal is very easy and can be done, only when
the operating voltage is out. Proceed according to the numbers.
Press the two clamps to the middle (1+2), hold it and pull the coin
tester after behind from the holder (3)

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 11 -
9.5 Electrical connection
The electric connection may only be carried out by
 qualiedandauthorisedpersonnel!
The electrical connection must be installed complying to the
current local VDE regulations. With a permanent connecti-
on the all-pole mains interrupter switch contacts must have at
least a 3mm gap. Before starting with the electrical connection
theappropriatemainscircuitmustbeswitchedo󰀨.Activatethe
appropriate immobilising switch, remove the fuse or trigger the
mains safety fuse.
From a standard wall socket the supplied mains supply cable is
inserted through one of the two drilled holes to achieve the elec-
tric connection. After the electrical connection has been achie-
ved, can the SunCash be re-assembled.

Cable entrance
IEC connector
Power plug
Cable entrance
9.6 Operatingforthersttime
After successful installation the SunCash can be operated. For
thispurposethemoneyhopperandcarddispensermustbel-
led.Themoneyhopperiseasilylledfromabovebutonlyuptoa
maximumof1cmbelowthetop.Thecarddispenserisalsolled
from above, to a maximum of 1cm below the top lip. It makes no
di󰀨erencewhichwaythecardsareinserted.Theattachedchip
cardcovermustlayatonthechipcardstacktopreventprob-
lems by a low card stack. As soon as the mains circuit and the
internal mains switch have been switched on, appears in the dis-
play for about 2 seconds an information about the operating type
of your SunCash and the software version used (e.g. Holtkamp
SunCash version X.x -), after that appears in the display ‘money
changer ready’. SunCash is now ready for use and can now be
programmed to your wishes. You should carry out an intensive
test to ensure that the programming has been properly carried
out. After the test run, the counters should be reset to ensure
correct accounting. Generally speaking also for further operati-
on, every time the device is opened, the mains supply must be
switchedo󰀨bytheinternalmainsswitch!
Consider the great volume and therefore the consider-
able weight (up to 50 kg), of the coin box when it is
 lledwithcoins.Thereforedonotremovethefullcoin
box out of the grooves. To remove the money, it is suf-
 cienttoremovethecoinboxtothestop.
Take into account that the installed software has been set up
for the installed components and there adjustments. That means
thatinstallingothercomponentsorchangingthecoinhopperl-
ling with other sorts of coins will result in complications. Should
you want to install or change components like dispenser, hopper,
electronic multiple bank note reader, electronic coin tester, chip
cardcontactunitorllthecoinhopperwithadi󰀨erentcoinsort,
then please ask us for information! Should you for any reason
removeacomponentoutoftheSunCash,switcho󰀨themains
supply. Either direct at the fuse box or with the installed mains
switch!


Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 12 -
10 Keypad
For operating and programming is a 5-button key pad placed in
the upper third part of the SunCash.
By pressing the Card button you switch
from money change mode to card sales.
By pressing the PLUS button you chan-
geinto the congurationsmenuwhenyou
press the PLUS button as well as inserting
a type 53 chip card. In programming mode
the indicated value can be raised by pres-
sing the PLUS button. When you are in the
statistic menu with a type 43 chip card in-
serted, by pressing the PLUS and RESET
button together the current statistic value
can be cancelled.
In programming mode the indicated value in
the display can be reduced by pressing the
RESET button. By pressing the RESET but-
ton with an inserted chip card type 43 and
simultaneously pressing the PLUS button
the current value can be cancelled.
In the case of a blinking display you can
enquire the malfunction details by pressing
the service button.
By pressing the OK button all proceedings
areconrmed.Inprogrammingmodeeach
press of the button takes you one menu
item further. If you have been through all the
menu items, the chip card will be rejected.
11 Basic functions
11.1 Money changing operating
11.1.1 Bank note change
After switching on the SunCash goes automatically into the mo-
ney changing operation. In the display appears “Money changer
ready”.
To change money, push the bank notes which are to be changed
one after the other into the bank note slot. Every bank note ch-
anges straight away into coins. If the owner has, with the help of
a type 53 chip card, a change bonus activated, then after every
accepted bank note in the display for about 2 seconds will appe-
ar the maximum money change amount “Money change max.”,
and then the total sum of the read notes “Money change cur-
rent”. The maximum money change amount can be preset in the
conguration menu. Payment occurs after about 1 minute, un-
less, the OK button is pressed or the maximum money changing
amount has been reached.
In these cases the SunCash begins to pay out the coins. By
trying to overpay the bank notes are refused. In the case of a
mains failure the already paid amount will not be lost but is sto-
red. After the mains failure you can carry on changing as normal.

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 13 -
11.1.2 Coin change (only possible with 2. hopper)
The SunCash can change larger coins into smaller. There was
always spent the smallest available priority. Each coin is chan-
ged directly, sometimes therefore no amount of change bonus
can be achieved.
In the same time can be changed notes in coins, or coins in coins.
If a coin is changed into another, the note acceptance is blocked.
As long the hoppers are empty, only the chip card sales and
revaluations of chip cards are possible.

11.2 Chip card sales
SunCash also sells chip cards. The deposit for a chip card can
bepre-setincongurationsmenuinmenuitem“Card deposit”.
To buy a chip card, press the Cardbuttononthekeyeld.Inthe
display appears for about 2 seconds “Card deposit x EUR”, and
then “Amount due x EUR”. You have now about 1 minute to pay
the right amount indicated.
An overpayment is not possible. All coins and bank
notes which have a higher value as the amount due will
automatically not be accepted.
After successful payment with coins or bank notes appears on
the display “One moment please”, and the chip card can be
removed out of the card slot. If by mistake the card sales function
has been activated, one press of the RESET button is enough to
get back to the money change mode.

In the case of a mains failure, during a buying transaction, the
already paid amount does not get lost but is stored. After the
mains failure you can carry on paying as normal. A maximum of
1 minute are required for the buying transaction. Should the card
deposit in this time not be fully paid, the already paid amount will
be lost and the amount already deposited appears as positive
decitinstatistics-menu.
The SunCash switches over automatically to the money
changing operation.

11.3 Revaluing of chip cards
SunCash also o󰀨ers the possibility, to revalue, from SunCash
purchased or appropriate business bound coded chip cards of
the type 11. To do so push the chip card type 11 into the card slot.
The display will show “Curr. x EUR/Max. x EUR”, as information
for the current chip card value and as information to the highest
amount which can be revalued. Through payment by coins or
bank notes can the chip card now be re-valued. By pressing the
OK button the amount will be stored onto the chip card, the chip
card will be rejected and the display will show “Card value: x
EUR”. Alternately the chip card will automatically be rejected af-
ter 1 minute.
Should the chip card be removed during the revaluing, must the
same card be inserted again within 5 minutes, this wise the paid
amount will be lost.
In the case of a mains failure during a revaluing action, the alrea-
dy paid amount does not get lost but is stored. The chip card will
automatically be rejected by a mains failure.
After the mains failure the same chip card must be reinserted
within 5 minutes. If this does not happen then the already paid
amount will be lost and SunCash switches over automatically to
money changing operation.

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 14 -
12 Chip card types
There are various chip card types for customers as a means of
payment. Further for the programming of standard and special
functions various service and enquiry cards.
Inthefollowingtableyouwillndanexplanatorylistofthetype
of available chip cards.
Chip card type
PIN-CARD Function
P11 revaluable chip card for customer
P33 Chip card for querying the statistics and deleting the daily counters (forowner/sta󰀨)
P43 Chip card for querying and deleting the statistics (Exclusively for the owner / Caution: Danger of manipulation!)
P53 Menu programming chip card (Exclusively for the owner / Caution: Danger of manipulation!)
P73 Chip card for activating the initialization function (forowner/sta󰀨/Caution:Dangerofmanipulation!)
13 Programming
13.1 Explaning the programming positions
IntheprogrammingmodetheSunCashhasthreedi󰀨erentpro-
gramming menus: the Conguration menu, the Bonus menu
and the Card initialisation menu. With the help of the key pad
on the SunCash and the appropriate chip cards, you can move
about the menus as follows.
Through pressing the RESET button, the adjusting value is re-
duced, through pressing the PLUS button, the adjusting value
is increased. Through pressing the OK button you change to the
next programming step. The menu is left and the card rejected,
when the menu has been completed.
Which program position in which menu is to be found and what
they mean is explained as follows.
It will always be declared, that DIP switch Nr. 3 must be
set at on for programming. The DIP switch should also
stay at this position after the programming.
13.1.1 Congurationmenu
Thecongurationsmenuo󰀨ersyouthepossibilitytodoallthe
programming concerning the values for the hopper, coin tester
and bank note reader in this menu.
Thevalueadjustmentstaketherstprogrampositions.Thevalu-
eso󰀨ersyouthepossibility,thevalueoftheinsertedorpaying
out coins or notes for the SunCash to be set individually. They
are already factory set and on the installed coin tester/bank note
reader adjusted and may only be changed in the following cases:
●If a coin/bank note tester for foreign currency has been in-
stalled later.
Only possible after consultation with Holtkamp.
●If the value of the token is to be changed.
●If one or more kinds of coins or notes are to be banned.
● Ifotherkindsofcoinsaretobeusedwhenllingupthe
hopper.
Only possible after consultation Holtkamp.

Your SunCash is tted with an electronic multiple coin tester
(EMP) and a bank note reader. Because of this it can read and
accept six di󰀨erent coins and notes. Should a coin or note be
paid in, it notes just the insert, do not know yet which value the
coin or note has for your SunCash. This evaluation is achieved
with the help of the channel value program.
haben soll. Diese Wertzuschreibung erfolgt mit Hilfe der Pro-
grammierung der Kanalwertigkeiten.



Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 15 -
toopen:         Congurationsmenu:
1 2 3 4
set DIP switch
No. 3 o „ON“
(upwards)
push PLUS
button and
hold
insert
chip card
type 53
release
PLUS button
Language
Coin tester value K1:
Coin tester value K2:
Coin tester value K3:
Coin tester value K4:
Coin tester value K5:
Coin tester value K6:
Note reader value K1:
Note reader value K2:
Note reader value K3:
Note reader value K4:
Note reader value K5:
Note reader value K6:
Coin value hopper 1
EMP channel hopper 1
Coin value hopper 2
EMP channel hopper 2
Currency
Putout lamp
Card will be rejected!
leave by:
Leave the menu by pressing
the OK button so often so the
end of the menu is attains. The
chip card will be automatically
rejected.
It is possible to block separate channels. Thereby the acceptan-
ce from the coin, which is accessed this channel, will be denied.
The blocking of separately channels is possible as follows:
●Please orientate you on the basis of the tables, which be
 a󰀩xedonthesidecoverfromthecointester
Example for attitude a EURO coin tester with 2 inserted hop-
pers:
Channels 12345678
Bank 1 Coin € 0,5 1 2 WM TK - - -
Assortment A C D A A - - -
Channels 9 10 11 12 13 14 15 16
Bank 2 Coin € 0,5 1 2 WM TK - - -
Assortment C A D A A - - -
A in cash WM Holtkamp-Standard-Token
C in hopper 2 TK free programmable token
D in hopper 1
●by repeated pressing of the OK button, you will arrive at the
required position
●change the value with the PLUS or RESET button to “0”
●leave the menu so often pressing the OK button as the chip
card is rejected

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 16 -
Your SunCash is factory setting with a standard program-
ming. You see the program values in the follows:
Language
Deutsch
Herethepossibilityisorderedtoselectbetweendi󰀨erentlangu-
ages. The following languages stand to the selection: German,
Italian, English, Norwegian, Danish and Swedish.
Coin tester value
K1: 0.5 EUR
Thecointestervaluechannel1o󰀨ersthepossibility,tosetthe
channel values for channel 1. The values can be set in steps of
0.1, from 0.0 to 999.9. With the RESET and PLUS button you
can alter the number values, with the OK button you switch to
the next menu item. The set values should always correspond to
the actual values
With the setting 0.0, the equivalent valued channel of
the electronic multiple coin tester will be automatically
disabled.
Coin tester value 2-6
Analogue coin tester value channel 1
Channel 2: 1.0 EUR
Channel 3: 2.0 EUR
Channel 4: 0.0 EUR
Channel 5: 0.0 EUR
Channel 6: 0.0 EUR

Note reader value
K1: 5.0 EUR
Thenotereadervaluechannel1o󰀨ersthepossibility,tosetthe
channel values for channel 1. The values can be set in steps of
0.1, from 0.0 to 999.9. With the RESET and PLUS button you
can alter the number values, with the OK button you switch to
the next menu item. This setting should always correspond to the
actual value of the bank notes!
With the setting 0.0, the equivalent valued channel of
the electronic bank note reader will be automatically
disabled.

Note reader value 2-6
Analogue note reader value channel 1
Channel 2: 10.0 EUR
Channel 3: 20.0 EUR
Channel 4: 50.0 EUR
Channel 5: 0.0 EUR
Channel 6: 0.0 EUR
Coin value hopper
1: 2.0 EUR
The coin value hopper 1 o󰀨ers the possibility, to set the value
of the money pieces or tokens which are to be found in the coin
hopper 1. The value can be set in steps of 0.1 from 0.0 to 999.9.
With the setting 0.0 the hopper is inactive. If the coin value of
hopper 1 and 2 is set to 0, the money change function will be
inactive. By that a new standard operating type is active: card
sales. Therefore in the display will appear “Card deposit”.
With the RESET and PLUS button you can alter the number
values, with the OK button you can switch to the next menu item.
This setting should always correspond to the actual coin value!
EMP chan. hopper
1: 3
To adjust is here the assignment, which coin (designates by their
EMP channel) falls in hopper 1. This is important for the calcula-
tionsofthelldi󰀨erence.
EMP chan. hopper
2: 0.0 EUR
Analogue coin value hopper 1
If no second hopper is installed, the value should be abso-
lutely adjusted to "0“!


Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 17 -
EMP chan. hopper
2: 0
Analogue coin value hopper 1
If no second hopper is installed, the value should be abso-
lutely adjusted to "0“!

Currency:
EUR
ThesettingCurrencyo󰀨ersyouthepossibility,tochooseunder
the currency abbreviations EURO; SFR; HFL; DKr; Kr; PLN; or
also no abbreviation (——). The currency abbreviation will ap-
pear in the display. With the RESET and PLUS button you can
change to other abbreviations, with the OK button you can leave
the menu and the chip card type 53 is ejected.
Pay attention by switching over from EURO to other
currencies or inverse! Value cards are then rejected.
Therefore switching should be completed only after
consultation with the company Holtkamp

Output lamp:
automatic
x = automatic: The output lamp shines only a certain time, if
one changed.
switchedo󰀨:  Theoutputlampnevershines.
switched on: The output lamp ever shines.
to open: Bonus menu:
1 2 3 4
DIP switch
No. 3 o „ON“
(upwards)
push PLUS
button and
hold
insert
chip card
type 53
Maximum change amount
Card pawn
Initialisation amount
Revalue bonus step 1
Revalue bonus amount 1
Revalue bonus step 2
Revalue bonus amount 2
Revalue bonus step 3
Revalue bonus amount 3
Revalue bonus step 4
Revalue bonus amount 4
Revalue bonus step 5
Revalue bonus amount 5
Change bonus step 1
Change bonus amount 1
Change bonus step 2
Change bonus amount 2
Change bonus step 3
Change bonus amount 3
Change bonus step 4
Change bonus amount 4
Change bonus step 5
Change bonus amount 5
Card will be rejected!
leave by:
Leave the menu by pressing
the OK button so often so the
end of the menu is attains. The
chip card will be automatically
rejected.
13.1.2 Bonus menu
Thebonusmenuo󰀨ersyouthepossibility,tosetallbonusand
prices for the operation of the SunCash. You must insert chip
card type 53.

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 18 -
Max. change:
50.0 EUR
ThesettingMaximumchangeo󰀨ersyouthepossibility,tosetthe
maximum amount which can be changed at one time. With the
RESET and PLUS button the number values can be altered in
steps of 0.1 from 0.0 to 9999.9. With OK button you switch to the
next menu item.
Note: If the maximum altered value is set to more than 20
coins, the coin hopper can run out and therefore not pay out
the full sum.

Card pawn:
5.0 EUR
Thecardpawno󰀨ersyouthepossibility,tosetthepriceforthe
purchase of a card. The card deposit can be set in steps of 0.1
from 0.0 to 999.9. With the setting 0.0 the card sales is deacti-
vated.
By the card pawn setting you must pay attention, that
the pawn setting, divided by the smallest set channel
value of the coin tester/bank note reader reaches a
whole number, as overpaying is not possible.
With the RESET and PLUS button you can change the values,
with the OK button you switch to the next menu item.

Initial amount:
0.0 EUR
Theinitialamounto󰀨ersyouthepossibilitytosettheamountin
a card initialisation operation, which will be re-valued to a type
11 chip card. The initialisation amount can be set in steps of 0.1
from 0.0 to 999.9. With the RESET and PLUS button you can
change the values, with the OK button you switch to the next
menu item.
Revalue bonus step
1: 0.0 EUR
Therevaluebonusstep1o󰀨ersthepossibility,tosetacertain
revalue amount, which the chip card type 11 is re-valued with
an extra bonus to the value of the revalue bonus amount 1.The
revalue bonus step can be set in steps of 0.1 from 0.0 to 999.9.
With the RESET and PLUS button the values can be altered,
with the OK button you switch to the next menu item.
The revalue bonus steps must be programmed in an in
creasing sequence that means, the revalue bonus step 1
must be smaller than revalue bonus step 2 etc. When 5
revalue bonuses are not required, the ones which are not
used can be set at 0.0, then they are deactivated.
The particular revalue bonus amount is automatically
suspended.

Revalue bonus
amount
1: 0.0 EUR
Therevaluebonusstep1o󰀨ersthepossibility,tosetacertain
revalue amount, which the chip card type 11 is revalued with an
extra bonus to the value of the revalue bonus amount 1.The re-
value bonus step can be set in steps of 0.1 from 0.0 to 999.9.
With the RESET and PLUS the values can be changed by the
OK button you switch to the next menu item.
The revalue bonus amount must be programmed in an in-
creasing sequence that means, the revalue bonus amount
1 must be smaller than revalue bonus amount 2 etc.

Revalue bonus step 2-5 0.0 EUR
Analogue revalue bonus step 1
Revalue bonus step 2-5 0.0 EUR
Analogue revalue bonus step 1

Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 19 -
Change bonus step
1: 0.0 EUR
Thechangebonusstep1o󰀨ersyouthepossibilitytosetachan-
ge amount, which the change bonus amount 1 will be included
to the changed money which will be paid out. The change bonus
step 1 can be set in steps of 0.1 from 0.0 to 999.9. With the
RESET and PLUS button you can alter the values, with the OK
button you switch over to the next menu item.
The change bonus steps must be programmed in an in-
creasing sequence that means, the changed bonus step 1
must be smaller than change bonus step 2 etc. When 5
revalue bonuses are not required, the ones which are not
used can be set at 0.0, they are then deactivated.
The particular revalue bonus amount is automatically
suspended.
The acceptance of token must be disabled


Change bonus amount
1: 0.0 EUR
Thechangebonusamount1,o󰀨ersthepossibilitytosetthech-
ange bonus amount which is included in the pay out when a ch-
ange amount reaches the setting of the change bonus step 1.
The change bonus amount should be programmed in an
increasing sequence, that means, the change bonus step 1
must be smaller than change bonus step 2 etc.
Important! The bonus must be set so that the type of
 coinllingofthehoppercanbepaidout!
If a change bonus amount is set at 0, the operating be-
haviour of the SunCash change operation changes,
see 6.1 money changing operation.

Change bonus step 2-5 0.0 EUR
Analogue change bonus step 1
Change bonus amount 2-5 0.0 EUR
Analogue change bonus step 1


Holtkamp Electronics SUNCASH engl. techn. Stand 04.2016 4047_04.2016 V09.2019
- 20 -
to open: Card initialisation menu:
1 2 3 4
DIP switch
no. 3 to
„ON“
(upwards) insert
chip card
type 73
leave by:
Press RESET button
or automatically after 20 seconds
13.1.3 Card initialisation menu
Card
initialisation!
Theinitialisationmodeo󰀨erstheoperatorthepossibility,toset
the chip cards type 11 to a certain value. Should there be a resi-
dual amount on the chip card, this will be deleted and then with
the pre-set value overwritten.
The deleted amounts will be deposited in the statistic menu.
pull out
chip card
type 73
insert
chip card
type 11
insert
chip card
type 11
insert
chip card
type 11
Card
initialisation!
One moment
please…
Card
initialisation!
One moment
please…
Card
initialisation!
Card
initialisation!
ready