Standard Change-Makers BX Series Quick guide

Standard Change-Makers, Inc.
Indianapolis, Indiana
Two-Year
Limited Product Warranty
MC, BX and BCX Machine Series
Standard Change-Makers, Inc. (“Manufacturer”) warrants the machine (the “Product”), excluding any component(s) not manufactured by Standard
Change-Makers, Inc. (Third Party Product(s)), to be free from defects in material and workmanship if properly installed according to the Manufacturer’s
Installation Instructions and serviced and operated under normal conditions according to the Manufacturer’s instructions. THE MANUFACTURER
MAKES NO EXPRESS WARRANTIES WITH RESPECT TO, AND DISCLAIMS ANY IMPLIED WARRANTIES APPLICABLE TO, ANY
THIRD PARTY PRODUCT(S) INCORPORATED INTO THE PRODUCT INCLUDING WARRANTIES AGAINST INFRINGEMENT,
WARRANTIES OF MERCHANTABILITY AND WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE. However, the manufacturer
of Third Party Product(s) may have a warranty which is applicable to the owner of the product. Please contact the Manufacturer for additional warranty
information regarding the Third Party Product(s).
No other promise or affirmation of fact concerning the Product and no other description, sample or model of the Product shall be construed as augmenting
or supplementing this limited warranty, unless the additional warranty is in writing and signed by an authorized representative of Manufacturer. The
warranty period commences on the date the Product is put into service (“Installation Date”).
During the first twelve months after the Installation Date, Manufacturer shall repair or replace (without charge to the owner) the Product, or any component
or part thereof (except Third Party Product(s)), which is determined, in the sole discretion of Manufacturer, to have defects in materials or workmanship
prior to the Installation Date.
During the second twelve months after the Installation date, Manufacturer shall repair or replace the Product, or any component or part thereof, (except
Third Party Product(s)), which is determined, in the sole discretion of Manufacturer, to have had defects in materials or workmanship prior to the
Installation Date. During the second twelve months after the Installation Date, Manufacturer shall pay all costs for replacement parts, but the owner shall
pay all labor costs.
MANUFACTURER SHALL ONLY BE OBLIGATED TO PERFORM WARRANTY WORK IF THE PRODUCT, OR ANY COMPONENT
OR PART THEREOF, IS RETURNED TO MANUFACTURERS FACTORY, OR ONE OF ITS COMPANY-OWNED SERVICE CENTERS.
TRANSPORTATION CHARGES SHALL BE PREPAID BY THE OWNER.
Each Product shipped from the factory contains Owner’s Manuals. Before shipping a Product to Manufacturer or one of its company-owned service centers
for warranty work, the owner shall be certain that the source of difficulty could not be corrected by performing one or more of the procedures described
in the Owner’s Manuals. If Manufacturer finds, in its sole discretion, that the difficulty could have been corrected by following a procedure in an Owner’s
Manual, MANUFACTURER RESERVES THE RIGHT TO MAKE THEIR REGULAR CHARGE FOR ANY WORK PERFORMED.
This limited warranty shall not apply to any Product which must be repaired or replaced because of normal wear, which has been subject to misuse,
negligence, or accident, or which has been repaired or altered outside of Manufacturers factory, or one of its company-owned service centers, unless
authorized by Manufacturer. Manufacturer shall not be liable for any loss, damage, or expense (including, without limitation, the loss of money caused by
inadvertent machine dispense or by the use of counterfeit or bogus money) caused from or related in any way to the use of the Product or from any other
cause.
No person, agent, dealer, or any other entity is authorized to give or alter any warranties on behalf of Manufacturer nor to assume for Manufacturer any
other obligation or liability in connection with the Product. Manufacturer reserves the right to make design and/or operational changes to the Product
without obligation to incorporate these changes in to the Product covered by this warranty.
THIS LIMITED WARRANTY IS VALID ONLY IF AN OWNER’S WARRANTY REGISTRATION CARD HAS BEEN FULLY AND
PROPERLY COMPLETED AND IS ON FILE WITH THE MANUFACTURER. THIS LIMITED WARRANTY SUPERSEDES AND IS
GIVEN IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES APPLICABLE TO THE PRODUCT, THE BILL ACCEPTOR
OR BILL DISPENSER (WHETHER ARISING UNDER STATUTE, COMMON LAW, CONVENTION OR TREATY), INCLUDING
WARRANTIES AGAINST INFRINGEMENT, WARRANTIES OF MERCHANTABILITY AND WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE. MANUFACTURER’S OBLIGATION TO REPAIR OR REPLACE ANY PRODUCT, OR ANY COMPONENT OR
PART THEREOF, AS SET FORTH ABOVE SHALL BE IN LIEUOF ALL OTHER REMEDIES. IN NOEVENT SHALL MANUFACTURER
BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Effective January 1, 2003

Contents
1.0 Quick Start Guide.................................................................................................................... 4
1.1 Placing The Machine.............................................................................................................. 4
1.2 Removing The Internal Shipping Restraints.......................................................................... 4
1.3 Connecting Power To The Machine ...................................................................................... 5
1.4 Loading The Coin Dispenser ................................................................................................. 5
1.5 Loading the Bill Dispenser Cartridge .................................................................................... 5
1.6 Testing the Machine Operation............................................................................................ 11
1.7 Troubleshooting An Error Condition On The Dispenser..................................................... 11
1.8 Resetting the Dispenser........................................................................................................ 12
1.9 Removing Bills From The Bill Acceptor Bill Box .............................................................. 12
1.10 Emptying The Coin Dispenser............................................................................................. 13
1.11 Removing Coins From The Coin Acceptor Box.................................................................. 14
1.12 Power Considerations .......................................................................................................... 15
1.13 Environmental Considerations............................................................................................. 15
1.14 Bill Acceptor Considerations............................................................................................... 16
1.15 Bill Dispenser Considerations.............................................................................................. 16
2.0 Installation Details ................................................................................................................. 16
2.1 Cabinet Installation Instructions .......................................................................................... 16
2.2 Location of the Changer....................................................................................................... 17
2.3 Optional Base Installation Instructions................................................................................ 17
2.4 Wall Mount Changers.......................................................................................................... 17
2.5 Rear Load Changers............................................................................................................. 18
2.6 Mounting the Changer Cabinet............................................................................................ 19
2.7 Electrical Hook-Up .............................................................................................................. 20
2.8 The Locations Electrical Supply.......................................................................................... 20
3.0 Lock Operation ...................................................................................................................... 21
4.0 Understanding Machine Operating Concepts..................................................................... 22
4.1 Dual Redundancy Operating Mode...................................................................................... 24
5.0 Machine and Device Features............................................................................................... 25
5.1 Bill Acceptance and Bill Security (Feature Type = Device)................................................ 25
5.2 Fast Vend Shutoff (Feature Type = Machine) ..................................................................... 25
5.3 Error Timeout (Feature Type = Machine and Device)......................................................... 26
5.4 Serial Control (Feature Type = Machine)............................................................................ 26
5.5 Power Reset (Feature Type = Device)................................................................................. 26
5.6 Hold Escrow (Feature Type = Machine).............................................................................. 26
5.7 Dispenser Transfer (Feature Type = Machine).................................................................... 27
5.8 Forced Dispense Feature (Feature Type = Machine)........................................................... 27
5.9 Forced Dispense Override (Feature Type = Machine)......................................................... 28
5.10 Accumulate (Feature Type = Machine) ............................................................................... 28
5.11 Dispenser Type (Feature Type = Device)............................................................................ 28
5.12 Dispenser Sub Type (Feature Type = Device)..................................................................... 28
5.13 Stringing Detection Level (Feature Type = Machine)......................................................... 29
5.14 Count Out Items (Feature Type = Device)........................................................................... 29
5.15 No Bill Acceptor Shutdown (Feature Type = Machine)...................................................... 29
5.16 No Coin Acceptor Shutdown (Feature Type = Machine).................................................... 29
5.17 Like Value Override (Feature Type = Machine) ................................................................. 30
5.18 Mylar Note Check (Feature Type = Dispenser)................................................................... 30
5.19 Overpay Timer (Feature Type = Machine).......................................................................... 30

5.20 Bonus Tokens (Feature Type = Machine) ............................................................................30
5.21 Dispenser Value (Feature Type = Device)............................................................................31
5.22 Ticket Coast Time (Feature Type = Device) ........................................................................31
5.23 Ticket Transfer Factor (Feature Type = Device)..................................................................32
5.24 Tickets Per Notch (Feature Type = Device).........................................................................32
5.25 Bin Low Count Value (Feature Type = Device)...................................................................32
5.26 Bin Low Override (Feature Type = Device).........................................................................33
6.0 Troubleshooting & Maintenance...........................................................................................34
6.1 Dispenser Flash Codes..........................................................................................................34
6.2 Troubleshooting Chart ..........................................................................................................35
6.3 Frequently Asked Questions.................................................................................................37
6.4 Maintenance..........................................................................................................................38
6.5 Optional Coin Dispenser Counter.........................................................................................40
6.6 Coin Dispenser Sold-Out Configurations.............................................................................40
7.0 Bill Dispenser...........................................................................................................................41
7.1 Fujitsu Bill Dispenser ...........................................................................................................41
7.1.1 Bill Dispenser Cassette Magnets ......................................................................................41
7.1.2 How To Set Cartridge Position Magnets..........................................................................41
7.1.3 Setting The Magnets for The Correct Cassette Locations................................................42
7.1.4 Setting the cassette bill denomination...............................................................................43
8.0 Part Ordering Information....................................................................................................43
8.1 Bill Acceptors .......................................................................................................................44
8.2 Interconnecting Cables..........................................................................................................44
8.3 Coin Acceptor Kits ...............................................................................................................45
8.4 Miscellaneous Parts ..............................................................................................................45
8.5 Coin Dispenser......................................................................................................................45
8.6 Coin Dispenser Part Numbers...............................................................................................45
9.0 Model Specifications, Mounting & Packaging Detail..........................................................46
10.0 How To Change A Feature Setting........................................................................................58
11.0 APPENDIX –Switch Settings For All Features....................................................................A
Service Centers...................................................................................................................................FF

4
1.0 QUICK START GUIDE
Your machine has been shipped preprogrammed from the factory. All settings will be programmed to the
factory default unless otherwise specified at the time of order. The majority of new machine owners need
only read this section in order to learn the basic installation and operating features of your machine. For
more detail, or if you just enjoy reading technical information, see the remaining sections of this manual.
1.1 Placing The Machine
The machine should be located in an area where it can be easily bolted to the floor or to a wall
for security purposes.
The door should be able to swing fully open and not come in contact with anything else. This
allows easy access for filling the hoppers and removing the deposited money. Some models
require a full 180-degree door swing to allow the hopper contents (coins) to be manually
dumped.
If the machine is to be installed in an outdoor location, we recommend a Rear Load model
changer. The machine should be located in an area where it will not be directly exposed to the
elements: excessive dust/dirt, direct sunlight, and/or direct rainfall. We recommend the use of
a canopy over the machine to ensure a longer trouble-free service life as well as to provide a
convenience for your customers.
The machine power cord should be secured in a manner that will prevent accidental or
intentional unplugging.
1.2 Removing The Internal Shipping Restraints
Internal shipping restraints are typically used to secure the internal machine components during shipping.
The restraints used are of various types: shipping tape, shipping brackets or shipping bars. Shipping
brackets and bars can be identified by a label with the marking indicating their purpose. These should be
removed to allow full access to each device. See examples of shipping restraints below.
!!!! CAUTION !!!!
Always disconnect the 24V power supply(s) before adding or removing a module.
Failure to do so can result in corrupt data and premature component failure.
SHIPPING BAR –F50
FUJITSU
BILL DISPENSER
SHIPPING TAPE ON
BILL
ACCEPTOR
SHIPPING BRACKET-MC900
COIN DISPENSER
REMOVE BOTH
HEX. NUTS

5
1.3 Connecting Power To The Machine
The machine can be connected to a standard 115VAC power outlet. We strongly recommend a dedicated
line to the breaker panel. If the machine is located in a harsh electrical environment, or if dedicated line is
not feasible, the use of a high quality surge suppressor (same as used for home computers) is
recommended. If hardwiring of the machine is necessary, a qualified electrician should perform it.
1.4 Loading The Coin Dispenser
Loading the coin dispenser is a simple task. For coins contained in a bank bag, grasp the neck of the
bank bag and twist it to choke the mouth of the bag. Invert the bag and insert the neck of the bag into
the top of the coin dispenser. Loosen your grip on the bag neck slowly, letting coins feed down into the
dispenser. The table below shows a convenient filling level for the various standard coin dispensers.
When possible, you can turn your bank bags inside out and lessen the chance of small strings and threads
from accumulating in your coin dispenser. Clean coffee cans or plastic pails can also be used to fill the
coin dispensers.
Type
No. of Coins
Value
Nickel Dispenser
3,800
$190
Dime Dispenser
7,800
$780
Quarter Dispenser
3,200
$800
Dollar Dispenser
2,400
$2,400
1.5 Loading the Bill Dispenser Cartridge
If your machine is equipped with a bill dispenser read this section carefully. Bill dispenser reliability is
directly related to the condition of the bills loaded into the dispenser as well as to the care taken when
loading them. Several models and brands of bill dispensers are available. Identify the one included in your
machine using the pictures below and become familiar with the bill loading process.
Basic considerations for any bill dispenser are as follows:
BILL CONDITION - Bills that are in average to good condition will dispense more reliably than
heavily worn bills with folds and creases in them. Optimum performance of the bill dispenser is
achieved if the note condition is ATM fit or good teller grade currency. Torn, taped or curled bills
Modular
Coin
Dispenser
Quick view of
coins remaining
Status LED
(Yellow)
Power LED
(Green)
Coin Out LED
(Red)
Push Button
(Reset)

6
should be culled out. Broken packages (bricks) of new currency mixed with circulation notes will
feed but increase the possibility of stoppages. The use of broken packages (bricks) alone or in
significant quantities is not recommended. Ensure there are no folds that overlap neighboring
notes. For best results, the notes should be loaded into the cassette in 50-100 note batches.
Loading the cassette in larger batches can cause the edges of the notes to fold up as they are
inserted.
CORRECT DENOMINATION - Ensure that the denomination loaded into the bill cassette is the
correct denomination. The dispenser does not have the ability to verify that the bills loaded are the
correct denomination assigned to the bill dispenser. Note –the value is assigned at the factory and
is based on the customer order. To change a dispenser value, see the section in this manual called
Machine and Device Features, sub topic Dispenser Value.
BILL ALIGNMENT - It is important that the edges of the notes be reasonably aligned prior to
insertion into the cassette. This will reduce the number of jams and bills rejected to the reject bin.
CASSETTE HANDLING - Gently press bills into the cassette, do not force them.
REMOVING REJECTED BILLS - Bills that could not be successfully dispensed will be diverted
to the reject tray. These are not counted in the audit and the customer will still receive the correct
amount. These bills should be removed from the bill tray. Do not attempt to reuse them as they
will not likely dispense the second time either.
SOLD OUT GENERAL –A small number of bills will remain in the dispenser when it becomes
“sold out”. This insures that enough bills remain to finish any dispense that is in progress. These
bills may be reloaded along with new bills.
SOLD OUT FUJITSU –40 to 70 bills will remain in the Fujitsu dispensers after it signals a Sold
Out condition. An optional filler plate is available that will reduce this number to 10-30. The part
number for the filler plate is 4M00774-M. Avoid using this plate if any number of bills to be
dispensed during a transaction is greater than 10. Using the plate in this case may not leave enough
bills to finish a payout in progress and in turn can prevent the Transfer Feature from functioning
as desired. Example: Dispensing 20 - $1 bills and 6 - $5 bills for a $50 deposit. If the filler plate
is used the $1 bills can run out before the vend cycle is completed. If only12 of the $1 are present,
the user cannot possibly receive the correct change since an odd number of $1 bills are dispensed;
12 - $1 bills and 7 - $5 bills will be dispensed in this case if the Transfer Feature is active. Since
only 12 - $1 bills were present at the start of the vend, the user will be short changed $3. In this
case if the filler plate is not used the 20 - $1 bills would have been available.
CAUTION!
Some cabinet models include a tilting or rotating slide plate to allow easy access for loading bills.
Use caution when operating these to avoid pinching your fingers or damaging the cables.

7
BILL DISPENSER MODELS AVAILABLE
FUJITSU –MODEL F50
FUJITSU-MODEL F53
Glory - MinMech
Glory - MultiMech

8
FUJITSU MODEL F50 DISPENSER LOADING –Rear load machines (door on back of machine) utilize
a “slide” and “rotate” plate for optimum access for bill loading. Front load machines do use a slide only.
They do not include the rotate plate.
STEP 1
- Slide / pull dispenser out as far as it
will go.
STEP 2
- Swivel the dispenser (rear loads only) to
allow additional bill compartment access.
STEP 3
–Open the bill compartment door of the
dispenser.
STEP 4
–Slide the pressure plate back and snap
into position.
STEP 5 –Load bills so they are standing on end. Release the pressure plate so the bills are
pushed forward.

9
FUJITSU MODEL F53 DISPENSER LOADING –Push the green release button (label) on the cassette
to be removed and view instruction decals located inside the dispenser cartridge.
STEP 1 –Push green release button on front of
cassette to remove it from the dispenser.
STEP 2
–Press green button on back of cassette
to open it.
STEP 3 –Lift pressure plate in rear as shown.
STEP 4 –Lift pressure plate in front and load
bills.
STEP 5 –Return pressure plates to
original position and install cassette into
correct location in the dispenser.

10
GLORY MINIMECH DISPENSER LOADING
GLORY MULTIMECH DISPENSER LOADING
STEP 3 –Return the pressure plate to the
original position and install the cassette.
STEP 2 –Pull the green pressure plate
towards you and insert a stack of good
conditioned bills.
STEP 1 –Use the handle to pull the cassette
from the bill dispenser.
STEP 2 –Insert and rotate the key. Slide
the latch to the right while lifting the lid.
STEP 1 –Use the handle to pull
the cassette from the bill
dispenser.
STEP 3 –Pull the green pressure plate
towards you and insert a stack of good
conditioned bills.
STEP 4 –Return the pressure plate to the
original position, close the lid and install
the cassette.

11
1.6 Testing the Machine Operation
TURNING POWER ON / OFF –Your machine is equipped with a power disconnect feature. The type of
disconnect used is dependent upon the machine model purchased. Below are pictures of the various each
disconnects used. It is always a good idea to unplug the machine from the 110VAC power source
whenever possible.
It is always a good idea to position the machine power cord in a location where it cannot easily be tampered
with.
STATUS INDICATORS - When installation is complete and an ample supply of coins has been loaded
in the dispenser(s), and power has been turned on, the machine is ready for operation. The Status LED
(yellow / top) on each dispenser should be flashing at a fast steady rate of approximately 5 flashes per
second. This flash rate indicates that this dispenser is ready to operate. Be sure to check the status LED
on every dispenser to ensure the machine is fully functional; the machine can remain in service even if a
dispenser is not functional. You are now ready to test the machine for proper operation. Note: A slower
flash rate (approx. 1 flash per second) indicates an error condition.
1.7 Troubleshooting An Error Condition On The Dispenser
If an error condition is present on any dispenser, the status LED will be flashing at a rate of one flash per
second and there will be a brief delay(LED will be off for approx. 3 seconds) between consecutive flashes.
This flash pattern indicates an error condition. If this occurs, count the number of flashes between the
pause. Do this several times to verify the correct Flash Code (number of consecutive flashes before the
pause). Refer to the “ATTENTION MACHINE OWNER” decal shown below (also found in machine) to
determine the source of the error for this flash code. Next, refer to the troubleshooting section of this
manual and find the probable causes for the error, as identified in the Troubleshooting Chart. Once the
failure cause has been corrected, reset the dispenser using the procedure outlined below. The status LED
flash rate should now return to the fast (5 flashes per second) steady rate.
Fast Vend Shut-Off
Bill Acceptor Error
Dispenser Sold-Out
Stringing Detected
Bill Jammed Error
Stacker Missing or Full
4
6
3
2
1
Power Fault Detected
6D00327
Unknown Error
Dispenser Error
Fatal Memory Error
9
8
condition is cleared.
ATTENTION MACHINE OWNER
FLASH CODE TABLE:
CODE
FLASH PROBLEM CODE FLASH PROBLEM
center.
511
10
7Coin Acceptor Error
12 Illogical Programming
13 Data Bad Error
14 Overpay Logic Error

12
1.8 Resetting the Dispenser
1.9 Removing Bills From The Bill Acceptor Bill Box
The bill box is attached to the rear of the bill acceptor. Each bill box will have an access door that can be
easily opened to allow the accepted bills to be removed. The location of the access door varies depending
on the bill acceptor model, yet all are easily viewable. See the pictures below for the common access door
locations.
Pyramid Acceptor
Mars Acceptor
Coinco Acceptor
Each dispenser is equipped with a push
button that can be used to reset the
dispenser from an error condition. It is
only necessary to reset the coin dispenser
that is displaying the error flash code.
Allow at least 45 seconds after releasing
the button, for the entire reset process to be
completed. The flash code should change
back to the steady flashing pattern if the
error was successfully reset.
Coin Dispenser Without Door
PUSH BUTTON

13
1.10 Emptying The Coin Dispenser
The majority of coins in a dispenser can be removed from the hopper using the bulk dump method. Bulk
dumping refers to the manual method of emptying coins from a dispenser into a container. A few coins
will remain in the dispense disk following a bulk dump; these coins can be removed by performing an
electronic dump.
CAUTION
As a safety precaution you should never place your fingers in or near the coin dispense chute or in the
coin storage area of the coin dispenser when power is applied to the dispenser.
Bulk Dump Method
Electronic Dump - The coin dispenser must first be in a “Sold Out” condition and not in error. This
condition occurs when the remaining coins are insufficient to complete a vend for a large denomination
bill. The diagnostic LED will be blinking at a slow steady pace indicating a Sold Out condition. To
begin, turn the machine power off, then back on. Wait for the machines Out Of Service lamp to change
from the constant ON state to a BLINKING or OFF state. Make sure that the dispenser is flashing a
dispenser sold out code. If any other flash code is shown when pressing the Push Button, it will reset the
dispenser. You will have to power cycle the dispenser again. Next, press and release the Push Button
(see diagram above for location). The dispenser will begin dispensing within 5 seconds. The coin
dispenser will stop when all coins have been cleared. Note: The push button must be pressed within 5
minutes of the time the power was turned off / on to the machine.
Dump
Position
Coin Dispenser –Bulk Dump
Bulk dumping is performed the same way for all
standard capacity (3200 quarters) coin
dispensers. Do not use the bulk dump method to
empty a high capacity hopper unless it has only
30% or less of the coins remaining. Coin
dispensers in front load machines tilt forward,
and dispensers in rear load machines tilt back.
Always TURN POWER OFF before bulk
dumping a hopper for safety purposes. To tilt the
coin dispenser, pull forward at the top edge of
the dispenser.
MC920 Bulk Dumping a 10K Hopper

14
1.11 Removing Coins From The Coin Acceptor Box
If your machine was equipped with the optional coin acceptor, you will need to empty the coin acceptor
box when it becomes full. To do this you need only to lift the coin box from the retaining bracket, empty
the box and then return it to the original position. The coin box should be free to be removed without the
use of tools. Some models have a shipping bolt or nut that is used to attach the coin box to the mount
during shipping. If this has not been removed, remove it at this time. The shipping bolt or nut is no longer
required.
NOTE: ON THE MC700 CHANGER, REMOVE THE 2 SCREWS IN THE BOTTOM OF THE
CHANGE BOX TO ALLOW THE BOX TO BE REMOVED TO DUMP THE COINS.

15
EXTERNAL CONSIDERATIONS
1.12 Power Considerations
GENERAL RANGE DETAILS
OPERATING VOLTAGE
105 VAC - 135 VAC
See “Power Considerations”
POWER CONSUMPTION
80W (min) - 360W (max)
See “Power Considerations”
OPERATING TEMPERATURE
0 - 60oC (32 - 140oF)
See “Environmental Considerations”
ELECTRICAL SERVICE
15A –DEDICATED RUN
See “Electrical Hook-up”
The MC machine series is equipped with a highly efficient “switching power supply”. One advantage of
this type of power supply is its abilityto deliver steady output power when encountering large fluctuations
in input voltage - 100VAC to 135VAC. In addition, this supply will only use power when it is needed
during the change making process. This means the heat created by the power supply is only generated for
brief periods of time and as a result will create very little heat build-up inside the machine. Heat build-up
can have adverse effects on the life of the machine components as well as the performance of the bill
acceptor.
The power consumption of your particular machine model will vary depending on the number of modules
in the model you have purchased. One hopper machines will require a maximum of 60 Watts of
momentary power, two hopper machines will require 80 Watts, and Dual machines models that include a
second supply may require up to 160 Watts momentarily.
Ancillary items can increase the overall machine power consumption requirement. An example would be
the power consumption of a heater kit. The power consumption of this device (device draws 100% load
when on) is equal to the wattage of the heating element. A 100 Watt heating element in addition to the
momentary power supply draw of 80W would bring the total maximum power consumption of the
machine to 180 Watts. The maximum wattage for the entire machine, including ancillary items, should
not be allowed to exceed 360 Watts.
1.13 Environmental Considerations
Advance consideration should be given to the environmental conditions (temperature, dirt and moisture
extremes) the machine will be exposed to. A base machine model is intended for use in locations where
moderate temperatures are encountered and the machine has minimal exposure to the elements. A typical
location where a base model would be used is one where the machine is located inside a building. If
extended environmental conditions exist, the machine should be equipped with the additional ancillary
items required to ensure proper performance.
Moderate Environments –typically indoors:
These environments have a minimum temperature of 0o C (32o F) and a maximum of no more than 41o C
(106o F) as measured inside the machine. Keep in mind that all electro-mechanical equipment found inside
an enclosure will be affected by two sources of heat: the outside temperature of the enclosure and the heat
generated by the components inside the enclosure. The MC machine series is equipped with a highly
efficient “switching power supply” that generates very little heat. Therefore, the heat generated inside the
cabinet is of minimal consequence. As a rule of thumb: The power supply heat will only raise the inside
temperature to within 3–7o C (5-10o F) of the temperature outside the machine.

16
Extended Environments –typically outdoors:
These environments are characterized by temperatures either below or above that of the moderate
environment, and / or where the machine is exposed to additional weather elements. We recommend a
properly equipped Rear Load model changer for these locations. Whenever possible, we highly
recommend the rear load changer be placed in an area that minimizes the machine’s exposure to excessive
dust/dirt, direct sunlight, and/or direct rainfall. A canopy or other cover, that protects the machine from
direct exposure to sunlight and the elements, is strongly recommended. This simple precaution will not
only reduce maintenance issues for the changer’s major operating components; it will also increase the
potential operating life of the machine.
For climates that see sustained temperatures below the previously defined moderate levels (0o C / 32o F),
an optional Heater Kit is strongly recommended. For climates that see sustained temperatures above the
previously defined moderate levels (41o C / 106o F), the optional Outdoor Rated Power Supply is strongly
recommended.
The Outdoor Rated Power Supply will continue to function properly when exposed to temperatures up to
60o C (140o F). Therefore, it is stronglyrecommended for regions in the Southern and Southwestern United
States.
1.14 Bill Acceptor Considerations
The performance and life of the bill acceptor supplied with your machine is limited to the particular
manufacturers' specifications. See the Bill Acceptor owners' manual for the recommended operating
specifications.
NOTE: Most OEM bill acceptors are specified to operate properly between 0o C (32o F) and 50o C (122o
F) ambient temperature. These conditions meet our recommended specifications for a moderate
environment application. If the precautions, outlined above, for extended environment applications are
met, we do not anticipate any adverse operating conditions associated with OEM bill acceptors.
1.15 Bill Dispenser Considerations
The performance and life of the bill dispenser supplied with your machine is limited to the particular
manufacturers' specifications. Most bill dispensers will perform more reliably in environments that have
low humidity and are operated between a 0o C (32o F) and 50o C (122o F) ambient temperature. A cabinet
heating kit will help keep the humidity level low during daily temperature transitions (night to day when
humidity can increase rapidly) and seasonal changes.
2.0 INSTALLATION DETAILS
2.1 Cabinet Installation Instructions
(REFER TO MANUAL: #8M00356 Modular Series Machine Installation Manual on our web site)
Standard Change-Makers manufactures change machines in the following cabinet styles: 1) Free standing
consoles, 2) Front loading wall mount, 3) Through-the-wall rear load and 4) Slim-line vending changer.
Because physical locations vary, we do not suggest an exact method of installation. To assure proper
operation of your changer the following general guidelines should be observed:

17
2.2 Location of the Changer
The following points should be considered when locating a changer:
Service Access: Full swing of the door when opened for removing and replenishing revenues.
User Access: Easily accessed by customers and proper height from the floor. The height will vary
depending upon the changer model. Accessibility for the handicapped, as required by the Americans with
Disabilities Act (ADA) specifies that all controls (coin cup, coin insertion slots and bill acceptor slots)
shall not be higher than 48” (1220 mm), or no less than 15” (230 mm) from the floor for Forward Reach
or “Straight On” access. For Side Reach or “Side” Access, ADA requires that all controls shall not exceed
48” (1220 mm), or no less than 15” (230 mm) from the floor (revised in 2011).
The measurement shown is taken from the base (bottom) of the machine to the floor. Additionally, ADA
requires a 30” (760mm) by 48” (1220mm) “clear floor space” to provide sufficient clearance for a single
wheelchair and occupant.
OPTIONAL HEADER INSTALLATION:
The starter holes on top of cabinet should be pre-drilled (#35 0.1100 drill bit size) to remove the paint
inside of the hole. This will ensure proper tightening of the self-tapping screw. Install header using self-
tapping screws and flat washers (included) to top of cabinet. All screws should be tightened till snug, do
not over tighten. Make sure the screws will not damage anything inside the machines.
FOR MORE INFORMATION ON THE INSTALLATION AND ADA COMPLIANCE SEE
MANUAL #8M00356 –MODULAR SERIES INSTALLATION GUIDE. The ADA Compliance
Chart of installation rough opening heights is available for download from our web site. (SEE:
SERVICE TAB –OWNER’S MANUALS).
2.3 Optional Base Installation Instructions
The painted ¼-20 hex. bolts must be removed and discarded from top of base. Install cabinet using new
¼-20 hex bolts and flat washers (included) to top of base. All bolts should be tightened until tight.
2.4 Wall Mount Changers
Type of wall construction: For maximum security, it is recommended that the changer be installed on a
wall made of cement block, brick or other type of masonry. A wooden stud wall is acceptable but will
not provide the security or strength usually associated with masonry.
The mounting holes on the back of the changer will accommodate four 1/4-inch diameter bolts. See
Section 10 for all MC changers mounting hole patterns.
WARNING!
CHANGERS MOUNTED ON BASES ARE TOP HEAVY
The changer MUST be secured to a rigid vertical surface, as well as
to the stand to provide appropriate security, stability, and safety.

18
If the wall to which the changer will be mounted does not meet the construction standards above, we
recommend using the Standard Change-Makers stand. The stands are provided with mounting holes on
the top surface for mounting the changer and holes are also provided on the bottom for securing the stand
to the floor. A drill template is included with each stand. When using the stand, we recommend that the
changer be bolted to the wall as well as to the stand. This provides a highly secure installation. See Section
11 for all the stand assembly diagrams.
WARNING!!!
Welding the cabinet to any kind of mounting could cause damage to electrical components within the
machine! Warping of the cabinet may also occur. Welding of any kind to the cabinet during installation
will void the manufacturer’s warranty!
If welding is ultimately necessary, all components within the machine must be removed prior to
welding! Please contact our Service Department with any questions.
If the changer is to be mounted to a post, the post should be sunk in concrete for stability. It is also
recommended that the post be filled with concrete for strength. A steel plate with approximately the same
dimensions as the changer should be welded to the post. Bolt the changer to the steel plate through the
four 1/4-inch mounting holes drilled into the plate. Tack weld the heads of the mounting bolts to prevent
their removal. Four nuts and washers inside the changer can then secure the changer. If this method is
not feasible, the bolts can be bent after installation to prevent removal.
2.5 Rear Load Changers
A rear load changer cabinet must mount through a hole in the wall. The
stainless steel front plate, which extends 2 inches beyond the cabinet on all
sides, must be tight against the wall surface. The cabinet will be 13”-18”
deep. Its protrusion into the back room will be the difference between this
depth and the thickness of your wall. Allow for proper door swing. Also,
lay a bead of caulking inside the front plate before installation to prevent
moisture incursion.
Angle iron mounting brackets are available to secure the changer in place.
One side of the angle iron should be secured to the side of the cabinet. The
other side of the angle iron mounts to the wall. The installed angle irons will
provide additional support needed to minimize cabinet flexing when the door
is opened.
Some rear load models have the coin hoppers mounted on the door. When the hoppers are full and the
door is opened, a significant load occurs on the cabinet. This load can result in cabinet flexing if the cabinet
is not sufficiently supported. Repeated flexing of the cabinet can result in metal fatigue and stressed weld
joints on the cabinet.
When the cabinet is installed in a cinder block wall, as shown in Figure 1, the block wall will typically
provide enough support on the sides and bottom of the cabinet to prevent flexing. In locations where this
type of mounting is not feasible, for example a 2x4 stud wall, additional support is required. To sufficiently
support the cabinet, at least 75% of the cabinet bottom should be supported with load-bearing, non-flexing
material such as cinderblock or iron. In addition, the sides of the cabinet must also be supported to prevent
the cabinet from twisting when the door is opened. See Figure 2 for the required support areas.
Figure 1