Holtkamp Maxi 3200 User manual

Operating instruction
Maxi 3200
Coin box

Important: For safe and proper use, read the instructions for use and further product-related documents carefully and keep
it for later use!
For errors, technical errors, printing errors and incompleteness, we assume no liability.

Holtkamp Electronics MAXI 3200 techn. stand 09.2017 4025_09.2017 V09.2019
- 3 -
Südstraße 40 / D-49084 Osnabrück
[e-mail] /
www.holtkamp.de
Telefon: [phone], Fax: [phone]
Geschäftsführung: Magnus Michael, Uwe Staudinger; Sitz der Gesellschaft: Osnabrück, AG Osnabrück HRB 213567
Banken: Deutsche Bank Osnabrück, IBAN: DE28 2657 0090 0039 5251 00; SW IFT/BIC: DEUTDE3B265
Die Lieferung erfolgt zu unseren Allgemeinen Geschäftsbedingungen mit Stand Juni 2011 nach ZVEI unter Einbeziehung der Softwareklausel
zur Überlassung von Standard-Software als Teil von Lieferungen mit Stand April 2012 nach ZVEI.
Zusätzlich gelten unsere Vertragsbedingungen „Hardware/Schaltplan/Layout“ und „Auftragsfertigung“.
Es gelten unsere Einkaufsbedingungen mit Stand Januar 2018.
EU-Konformitätserklärung / European Union conformity explanation
Für das nachfolgend bezeichnete Erzeugnis / For the following designated product
Zeitsteuerung vom Typ / Time control type
MAXI 3200
wird hiermit bestätigt, dass die Bauart, in der von uns in Verkehr gebrachten Ausführung, den unten genannten Normen
entspricht.
It is hereby confirmed, that the construction in that execution brought by us in traffic corresponds to the standards specified
down.
Diese Erklärung gilt für alle Geräte, die nach den beiliegenden technischen Unterlagen, welche Bestandteile dieser Erklärung
sind, hergestellt werden.
This explanation applies to all devices, after the enclosed technical documents, which are components of this explanation,
are manufactured.
Einschlägige EG-Richtlinien / Relevant EC guidelines
RoHS-Richtlinie 2011/65/EU / RoHS Directive 2011/65 / EU
1. 2006/95/EG (Niederspannungsrichtlinie)
2006/95/EG (low-voltage guideline)
geändert durch
changed through
2014/35/EU
2. 2004/108/EG (EMV-Richtlinie)
2004/108/EG (EMV guideline)
geändert durch
changed through
2014/30/EU
Angewendete harmonisierte Normen:
Applied one harmonized standards:
EN 60335-1 von 01/2012 (Sicherheit)
EN 60335-1 from 01/12 (security)
EN 55022 von 12/11 (Emissionen)
EN 55022 von 12/11 (emissions)
EN 61000-3, Teil 2 + 3 von (03/2015 und 03/2014) (Emissionen)
EN 61000-3, Teil 2 + 3 von (03/2015 und 03/2014) (emissions)
EN 61000-6, Teil 1 + 2 von (10/2007 und 03/2006) (Immunität)
EN 61000-6, Teil 1 + 2 von (10/2007 und 03/2006) (immunity)
Diese Erklärung ist bindend für den Hersteller
This declaration is binding on the manufacturer
Manfred Holtkamp Elektronik GmbH
Südstraße 40 in 49084 Osnabrück
abgegeben durch:
Signature:
M. Hashemizadeh (EMV-Beauftragter)
..........................................
Osnabrück, den 20.04.2016

Holtkamp Electronics MAXI 3200 techn. stand 09.2017 4025_09.2017 V09.2019
- 4 -
Content
1 Legal information......................................................................................................................................................................... 5
2 Warranty ................................................................................................................................................................................5
3 Safety notices .............................................................................................................................................................................. 5
4 Notes on cleaning and maintenance ......................................................................................................................................... 5
4.1 Change battery .................................................................................................................................................................. 5
5 Spezicdata ................................................................................................................................................................................6
6 General data ................................................................................................................................................................................6
7 Illustration ................................................................................................................................................................................7
7.1 Illustration of device............................................................................................................................................................ 7
7.2 Illustration of electronic....................................................................................................................................................... 8
8 Installation ................................................................................................................................................................................9
8.1 Installation notes.................................................................................................................................................................9
8.2 Mounting notes................................................................................................................................................................... 9
8.3 Mounting instructions..........................................................................................................................................................9
8.4 Electrical connection...........................................................................................................................................................9
 8.5 Operatingthersttime ..................................................................................................................................................... 11
9 Specications ............................................................................................................................................................................ 11
10 Programming .............................................................................................................................................................................12
 10.1 ExplanationtheProgramming ..........................................................................................................................................12
  10.1.1Specialfunction(timemeter-DIP1 ........................................................................................................................... 12
  10.1.2Adjustmentpre-begintime(DIP2).............................................................................................................................. 12
  10.1.3Adjustmentmaintime(DIP3)..................................................................................................................................... 13
11 Bookkeeping-statistic menu..................................................................................................................................................... 14
 11.1 Inquiryschema-deletethestatistics ...............................................................................................................................14
 11.2 Explanationofthebookkeeping-statisticmenu ................................................................................................................ 14
12 Not programmable special equipments .................................................................................................................................. 15
12.1 Contactor 2 x 20 A............................................................................................................................................................15
 12.2 Connectionfortimestop...................................................................................................................................................15
 12.3 Current-dependenttimestop............................................................................................................................................ 15
12.4 Potential free relay contact............................................................................................................................................... 15
 12.5 Current-dependenttimestop............................................................................................................................................ 15
 12.6 Short-timebutton.............................................................................................................................................................. 16
 12.7 Deleteentrance ................................................................................................................................................................16
12.8 Coin barrier....................................................................................................................................................................... 16
13 Malfunctions ............................................................................................................................................................................ 16
13.1 General errors ..................................................................................................................................................................16
13.2 Special errors .................................................................................................................................................................17

Holtkamp Electronics MAXI 3200 techn. stand 09.2017 4025_09.2017 V09.2019
- 5 -
4.1 Change battery
TheMAXIusedforthememorystatisticsabatteryTypCR2032,
thisshouldbechangedall2years.Ifthisnothappened,thesta-
tistics can be lost.
How to change the battery:
The battery-changing can only be done by authorised
 andqualiedelectricians!
RemovethevoltagefromtheMAXI.Removethefrontplate.Bra-
zeouttheoldbatteryandtakeanewbattery.Takecare,thatyou
brazethenewbatteryintherightway!Itisimportanttoconnect
the device after the changing for a short time. If this not hap-
pened,thenewbatterycanbeemptyinafewdays!IftheDIP-
points are ashing go over the bookkeeping-statistic menu to
deletethiserrormessage.
1 Legal information
Allrightsreserved.Nopartofthismanualmaynotbereproduced
orcopiedinanyformwithoutpermissionofHoltkampElektronik
GmbH.Therightsforcontainedsoftwareincontrolandmemory
blocksareexclusivelyfromthemanufacturer.Thereadingand
copyingoftheprogramcontentisstrictlyprohibited.
TheHoltkampElektronikGmbHisnotliabletothepurchaserof
this product or third parties for damages, losses, costs or ex-
pensescausedbythebuyeroranythirdpartyduetoaccident,
misuse or unauthorized alterations, repairs or improvements.
TheHoltkampElektronikGmbHshallremainliableforanyloss,
costs,disruptionsorconsequentialdamagesthatresultfromthe
use of the control.
Thetechnicaldata areup todate.Misprints, errorsandmodi-
cationsexcepted. Oldermanualsarenolongervalidwith the
publicationofthismanual.
ATTENTION:
The installation must be performed by authorized
personnel! Therefore, make sure that the installation
is carried out by an electronics specialist! Since this
isastationarydevicewithmain-sidexedconnecti-
on, a circuit breaker must be installed on the instal-
lation side!
4 Notes on cleaning and maintenance
Thedeviceismostlymaintenance-free.Bypoorcoinacceptan-
ce,the coinrunway ofthe mechanicsingle cointester canbe
cleanedwithadampclothorbrushtoremoveanydustorde-
posits.Themetalcasingcan becleanedwithadampclothor
acleaningagentwhichcanbedissolvedinwater.Donot use
underanycircumstances,thinners,petrol,acetoneorscouring
cleaning agents.
2 Warranty
Onthefunctionofthedeviceisgrantedforaperiodof12months.
Thewarrantyislimitedsolelytotechnicaldefectsoftheunit,it
can´tbeacceptedfurtherclaims.Furtherapplyourgeneralterms
andconditions,standofJune2011,forproductsandservicesof
theelectricalindustry(ZVEI)-alsoseewebsite:www.holtkamp.
de.
Anyliabilityextinguishedbythemanipulationofthedevice.
3 Safety notices
The coin boxes are built according to the prior art and the reco-
gnized safety rules.
Nevertheless,itsusethreatstolifeandlimboftheuserorthird
parties,orcausedamagetothedeviceorotherequipmentdu-
ringuse.Usethedeviceonlyinperfectcondition,andintended,
safetyandtheriskofdanger,incompliancewiththeinstruction
manual! Do immediately eliminate particular disorders, which
maya󰀨ectsafety!Alwayskeeptheoperatinginstructionsdirectly
tothecoinbox!Note,inadditiontotheuserguide,thegenerally
applicablelegalandothermandatoryregulationsrelevanttoac-
cidentpreventionandenvironmentalprotection!
Performnochangesand/ormodicationstothecoinboxwithout
approvalofthemanufacturer!Sparepartsmustmeettherequi-
rementsspeciedbythemanufacturer.Thisisguaranteedonly
fororiginalspareparts.Doobservetheintheusermanualspeci-
edorprescribeddeadlinesforrecurringmaintenanceintervals!
Doprovideforthesafeandenvironmentallyfriendlydisposalof
plasticpartsandelectronicreplacementparts!
Themanufacturerisnotliablefordamagecausedbyimproper
use.Theuserbearstherisk.Intendedusealsoincludescom-
pliancewiththeoperatinginstructionsandcompliancewiththe
inspectionandmaintenanceconditions



Holtkamp Electronics MAXI 3200 techn. stand 09.2017 4025_09.2017 V09.2019
- 6 -
5 Spezicdata
Write down the following data:
Keynumber(imprintonthekey)
Numberofidenticationfromdevice(seebookkeeping-statisticmenu)
Commission(namecustomer)
Trader (viawhichthedevicewaspurchased)
6 General data
Casingmaterial Galvanisedsteelplate1,5mm
Casing color Powder-coatedwhiteRAL9016
Color design foil yellow orange
Designfoilfromcustomer on request
Dimensions h255mmxw170mmxd135mm
Weight ca.4,0kg
Temperaturerange 0° to 50°C
Voltagemaintenance 230Vor24V,50/60Hz
Switched power 6,3Abycosphi=1;230V/24V
Power absorption 3,3VA
Protection class I by 230 V~ or III by 24 V
Protection type IP20
FusecircuitboardSI1 50mAT
Attention: Fuses may only be replaced with the same
value!
We reserve the right to technical changes in the production and
technical developments.

Holtkamp Electronics MAXI 3200 techn. stand 09.2017 4025_09.2017 V09.2019
- 7 -
7 Illustration
7.1 Illustration of device
1 Housing-lower part
2 Coin acceptor
3 Coin slot
4 Rejectbuttonforcoins*
5 Coin reject
6 Coin box
7 Removelofcoins
8 Lock
9 Buttonforaccounting-statisticsmenu
10 Frontplate
11 LED-Display
12 Designfoin(standard)
* (Special equipment) You can used the rejcet button for coins as door opener.
1
2
3
4
5
6
7
8
9
10
11
12

Holtkamp Electronics MAXI 3200 techn. stand 09.2017 4025_09.2017 V09.2019
- 8 -
1 DIPswitchforpricesettings
2 Connection for coin barrier
3 Connectionformechanicalhourcounter
4 Connectionformechanicalimpulsecounter
5 Connection for free use
6 Connectionforaccountstatisticmenubutton
7 Elektrical connection
8 Fusecircuitboard
9 Battery3VCR2032
10 DIPswitchfortimesettings(seechapter4)
11 Conntectionforshorttimebutton
12 Remotestart
13 Connectionfortimestop
14 Deleteentrance
15 Connection for coin acceptor
Specialequipment
7.2 Illustration of electronic
Circuit board MM-V99-1 230 V~
1
2
3
4
5
6
7
8
10
11 13 14 15
9
12

Holtkamp Electronics MAXI 3200 techn. stand 09.2017 4025_09.2017 V09.2019
- 9 -
8.4 Electrical connection
The electrical connection can be carried out only by
 authorizedandqualiedpersonnel!
The electrical connection can only be carried out by the local
VDEregulations.Withapermanentconnection,anallpolemains
separatorwithatleast3mmcontactgapmustbeused.Before
startingtheelectriccircuitmustbedisconnected.Shutdownthe
mainsinputbyactivatingtheseparatorswitch,removethefuse
or release the main safety fuse. Mains and low voltage cable
mustbespacedapart.Lowvoltagecablesshouldbegenerally
spaced as screened cables.
AftertheelectricalconnectiontheMAXIcancompleted.
Mainsandlowvoltagecablesmustbelaidseparatelyfromeach
other.Lowvoltagecablesshouldbelaidgenerallyasshielded
cables.Aftertheelectricalconnectionhasbeenmade,theMAXI
canbecompletedagain.
8 Installation
8.1 Installation notes
Throughmicro-electronics,the"MAXI3200"reachesahighreli-
ability in the daily use. This can only be reached if the installation
takesplaceexpertly.Heedwiththeinstallationnecessarily,…
● ShemustafterVDE-ruleandfromelectroexpertsisen
forced.
●With counters with 230V is necessary the connection of the
protection-leader and with counters with 24V is required the
protection-ladder as function-earth.
● Theoormustantistaticandconductive,thatnotstatically
loads.
8.2 Mounting notes
● TheMAXI3200weredesignedforthemontageonthewall
and for partial into the wall.
● Thecointimermustbewellfast.Forthis,pleaseusethe
 attachmentsofrearfromcasing.
● Thedeviceiscabledbymeansofthreadedmetricthreads
 onthebottomorrear.
●The MAXI 3200 corresponds to the protection-type IP20
 andcanbeusedonlyindryrooms/areas..
●TheMAXI3200mustbeinstalledverticallyandhorizontally
exactly. The inclination should not exceed 2° in any direction.
8.3 Mounting instructions
● Disconnectthepowersupplybymovingthecorresponding
 disconnector,withfuseorevenbytriggeringoftheprotecti-
ve switch.
● Unlockthelockofcoinacceptanceandremovethecoin
 ap.
● Loosenthetwofrontpanelscrewsandliftthefrontpanel.
● Disconnecttheelectricalconnectorsandremovethefront
 panelcompletely.
● Usingaspiritlevel,alignthebottomofthehousinghorizon-
 tallyandverticallyandmarkthethreemountingholes.
● Drill the holes and insert suitable dowels. Make
the electrical connection through the holes in the rear-
 wallorfrombelow.Metricthread(M20)ttingsarerequired
 whenwiringfrombelow.
● Thenxthehousingwithsuitablescrews.Nowrestorethe
electrical connections. Now replace the front panel and
 screwitinplace.Insertthecoinbox,thenplacetheremovel
 ofcoins,folditandlockit.
Control cable and remote
start connection have to be
kept away from each other.


Holtkamp Electronics MAXI 3200 techn. stand 09.2017 4025_09.2017 V09.2019
- 10 -
Connection 230 V
Connection lead
Remote start
(potential free)
Connection 230V~ Connection 24V~
MAXI 3200 MAXI 3200
230V~ 24V~
L2 PE N L3 L2 U0U1
LH NLU0U1
violet
Earth wire green-yellow
blue
black
LN
brown
L1
LH
violet
Earth wire green-yellow
blue
black
LN
brown
L1 PE
Remotestart Remotestart
LeadblindingtoPE
clamp!