Neptune IoT Hub Lite
HM-HUB-120
5. NETWORK CONFIGURATION SETUP
The Neptune hub comes with an intuitive web graphical user interface (Web-GUI) that allows users to easily configure its
various features through a web browser such as Internet Explorer, Firefox, Safari, or Chrome. Following these steps to access
the Web-GUI configuration utility from computer:
STEP 1: Connect computer to Neptune hub through its LAN port or WiFi access.
Ethernet: select “Obtain an IP address automatically” option for the computer’s network adapter, and then connect
it to the hub’s LAN port.
WiFi: search WiFi SSIDs: “Neptune_2.4G”, “Neptune_5GH”, “Neptune_5GL”, and connect to one of these SSIDs (no
password is required).
STEP 2: Open a web browser, and then enter the default IP address of the hub: 192.168.123.1.
STEP 3: Enter the default username: homa and password: homa in the Username and Password fields. Click Login to bring
up interface for configuration.
For WiFi Access Point mode (or Bridge mode) configuration, proceed further as follows:
STEP 4: Switch to /Network/WiFi menu, select Access Point mode (or Bridge mode), then select operating frequency band
(2.4GHz, 5GHz High-Band, or 5GHz Low-Band). For each frequency band, set the desired SSID name, password,
encryption type, access channel, and transmitted power level.
STEP 5: Click Apply to save the configuration.
After finishing WiFi configuration setups, following these steps to form Zigbee network:
STEP 6: Switch to /Network/Zigbee menu. Enable Permit Join to allow Zigbee client devices to join the network.
STEP 7: Follow the instructions on each Zigbee client device to register them to the network.
For complete WiPoNTM mode configuration to extend the network, and other advanced settings (such as forming Z-wave
network to connect Z-wave enabled IoT devices or connecting to 3G/LTE network through USB dongles), download the full
User’s Manual for Neptune IoT Hub Lite from the link: www.homatechs.com/support/Neptune/manual.
6. HOMA SMART APPS TO MANAGE AND CONTROL IOT DEVICES
Homa Home App is pre-installed on Homa Panel, a 10-inch Android tablet (Model: HM-PAN-210). This app is used to
communicate with the Neptune hub through WiFi to control IoT devices in every room, to get important notifications about what
is happening in your house, and to do the settings for whole Homa’s smart system.
Homa Mobile App lets you easily control, monitor, and secure your house from anywhere in the world. The app is
available to download on both Android and iOS platforms.
Federal Communication Commission Interference Statement
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This equipment may not cause harmful interference
(2) This equipment must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC
Caution:
Any
changes
or modifications
not
expressly
approved
by
the
party
responsible
for
compliance
could
void
the
user's authority to operate this equipment.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 24
cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the US/CANADA.
Operation of this device is restricted to indoor use only.
Support
Thank you for purchasing this HOMA product.
You
can
visit
www.homatechs.com/support/Neptune
to
access
the
latest
downloads
and
user
manuals. We
recommend
that
you
use
only
official
HOMA
support
resources.
If
you
need
further
assistance,
please
email
HOMA
Technical
Support:
support@homatechs.com.
HOMA Copyrights and Trademarks
©Copyright HOMA TECHNOLOGIES, JSC, 2019. All Rights Reserved.
HOMA, the HOMA logo, WiPoNTM are all trademarks or registered trademarks of HOMA TECHNOLOGIES, JSC (“HOMA”).
Any non-HOMA trademarks or trade-names in this publication are used for reference purposes only.
No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as
translation or adaptation) without written permission from HOMA. HOMA reserves the right to revise this publication and to
make changes in content from time to time without obligation on the part of HOMA to provide notification of such revision or
change.
HOMA provides this guide without warranty of any kind, implied or expressed, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose. HOMA may make improvements or changes in the product(s)
described in this guide at any time. The capabilities, system requirements and/or compatibility with third-party products
described herein are subject to change without notice.
