HOMCLOUD HY09RF WIFI User manual

1
Smart wi-fi Homcloud Chronothermostat RF
User Manual for
Gas Boiler and Water Underfloor Heating
PRODUCT SPECIFICATIONS
☆ Power Chronothermostat: USB
5V 1A DC or 4xAAA batteries ☆
Power RF Receiver: 90-240V AC
50/60HZ
☆ Temperature range: 1~70°C
☆ Display accuracy: 0.5°C
☆ Probe sensor: NTC (10k) 1%
☆ Temperature range: 5~35°C
☆ Contact capacity:5A/250V
☆ Size(mm)：130*90*25
☆ Homcloud code: XH-CTB
☆ Model n°: HY09RF WIFI
☆ Output: Switch relay
☆ Wireless frequency 2.412GHz ~
2.484GHz
☆ Max transmitting power:
802.11b:20dBm@1Mbps
☆ Network protocol: IEEE 802.11
b/g/n 2.4 GHz
☆ Encryption type: WPA/WPA2
☆ Antenna: PCB antenna
☆ Advanced password on App: 123456

2
DECLARATION OF CONFORMITY
Hereby, Life365 Italy S.p.A., declares that this wireless device complies with the essential
requirements and other related provisions of Directive 2014/53/EU of the European Parliament
and of the Council. The declaration can be consulted on the website www.homcloud.com/doc.
"Homcloud" is a registered trademark of Life365 Italy S.p.A.
INTEGRATION WITH ALEXA AND GOOGLE
Download and install Google Home or Amazon Alexa App and control your devices with your
voice with Smart Speakers or directly with your smartphone.
Important: If you want to link Homcloud App to Google Home or Alexa App you need to select
“Smart Life” App between the list of Google Home partners or Alexa skills. (after that
passage the user will be automatically direct to Homcloud App). NO NEED TO DOWNLOAD SMART
LIFE APP. JUST HOMCLOUD APP IS OK.
Please visit www.homcloud.com/config for support.
MAIN ICONS
Automatic Mode: run the
pre-set programmable mode
Manual mode
Holiday mode: you can set days
and temperature of holiday
(countdown mode)
Heating (if disappears means
stop heating)
Clock
Run the programmable
mode
P1 - run 5+2days 6 periods weekly
programmable mode P2 -
run 6+1days 6 periods weekly programmable
mode
P3 - run 7days 6 periods weekly
programmable mode
P1、P2、P3 select in the advanced setting
option AB (default is P1)
WIFI link status: connected
WIFI link status and cross:
disconnected
Cloud icon
EXPRESS INSTALLATION AND CONFIGURATION GUIDE (EXPERT)

3
1. ATTENTION: DISCONNET ELECTRICITY POWER BEFORE WORKING.
2. CONNECT THERMOSTATE AND RF RECEIVER TO POWER AND HEATING. SWITCH THEM
ON.
3. DOWNLOAD HOMCLOUD APP AND CREATE ACCOUNT.
4. WHEN THERMOSTAT AND RECEIVER ON, ON RECEIVER PRESS AND HOLD “PUSH”
BUTTON FOR 5-8 SEC UNTIL LED LIGHT ON RECEIVER IS SOLID BLUE (NOT BLINKING).
5. FOLLOW STEP ON APP TO FINISH CONFIGURATION. (ADD DEVICE..)
6. DEFAULT EXCHANGE OF INFORMATIO AND TEMPERATURE BETWEEN THERMOSTATE
AND RECEIVER AFTER THE FIRSTS 3 MINUTES WILL BECOME 20 MINUTES.
(YELLOW/ORANGE LIGHT ON RECEVIER BLINKING). IF YOU WANT TO SHORTEN
INTERVAL, JUST IF POWER IS BY USB, GO TO IP SETTINGS. (B5 AND B6)
7. DOWNLOAD AMAZON ALEXA or GOOGLE ASSISTANT APP AND LINK THEM TO
HOMCLOUD APP TO CONTROL DEVICE ALSO VOCALLY.
HOME SCREEN
BEFORE WIRING AND INSTALLING…
1. Keep out of the reach of children and away from water, dump or a wet environment.
2. Read these instructions carefully. Failure to follow them could damage the product or cause a

4
hazardous condition.
3. Check the ratings given in the instructions and on the product to make sure the produce is suitable for
your application.
4. Installer must be a trained experienced service technician.
5. After installation is complete, check out produce operation as provided in these instructions
6. Please remove batteries when USB power is working for a better using.
WIRING DIAGRAMS
CAUTION
Please arrange professional technician to install the product according to drawings and instructions.
Disconnect power supply before making any connection. Contact with components carrying hazardous
voltage can cause electrical shock.
13
the created group for convenient operation.
o Device information；Contains virtual ID；IP address；Mac address；Device time
zone
o Remove device: After deleting the device, you need to reconnect the network if
you want to use it.
o Third-party controls supported: amazon alexa/google assistant/IFTTT, click to
enter, you will see the steps
o
Imported by: Life365 Italy S.p.A. - European General Agency
Viale Roma 49/a, 47122 Forlì, Italy - Made in China

12
When no fault, normally on when loading or exchanging information
temporary.
PERMANENT RED LIGHT (solid or blinking): Faulty
When fault:
1. IP fault (IP:FFFF) : Light blinks 2 times every 2s
2. No wifi signal within 1h: Light blinks 3 times every 2s
3. External sensor fault: Light blinks 4 times every 2s
4. Sensor fault: Display says error “E1” or “E2”. Thermostat stop heating
until the fault I eliminated.
YELLOW/ORANGE LIGHT: RF matching
(B3 - IP matching code) When receiver is power-on, orange light is normally
on within 10s. Light goes off when finish matching. When receiver is
power-off, orange light is blinking within 10s.
BLUE LIGHT: Wifi matching
When power on state, long press receiver button “push” to match wifi.
SOLID BLUE: Normal pairing on EZ mode.
BLINKING BLUE: AP mode.
MAIN FEAUTURES ON APP
1. Power on/off button
2. Mode key: Manual mode, Auto mode, Holiday mode.
3. Child lock: If turned on, thermostate on wall cannot be operated.
4. Set key: After clicking on, you can select the programmed mode (5+2, 6+1, 7
days) and set the temp and time for 6 periods of the weekdays and weekend.
5. Settings:
o Device location: it is important to set a location if you want to use device with
geolocalization
o Share device: Share the device to the mobile phone or email account of the
registered family member
o Create Group: Add all the devices which need to operate at the same time to
5
INSTALLATION AND WI-FI SCHEME

6
DOWNLOAD AND REGISTRATION
(if you have got already Homcloud App on your mobile and an Account go to Configuration).
a. Download Homcloud App from App Store or Google Play or scan QR code below.
b. Enter the register/login interface and register with your country area code and phone
number/email address.
c. Wait a few minutes for verification code (by email or text message) and enter it where required
along with a password. (between 6 and 20 numbers and letters).
CONFIGURATION
Our App only support 2.4GHz Wi-Fi networks IEEE 802.11 b/g/n. For configuration both device
11
IMPORTANT: Considering battery usage, RF data updates every 20 minutes. If you prefer to
shorten interval, please use USB power and remove batteries. Follow B5 and B6 operation to
change this setting. (see below)
NO Setting Options Data Setting Factory
Default
B1 IP code low setting 00-FF 00
B2 IP code high setting 01-FF 01
B3 IP matching code (if any
problem, you can pair
thermostate and reciver here
again)
When you on B3 page, switch off and
then on at this moment receiver. After
that you should see “55” on display, and
that means IP matched successfully.
After that press “ ” on thermostat to
exit.
-
B4 Sensor state Sensor state
N1:single built-in sensor
N3:both built-in sensor and external
sensor. (when receiver with external
sensor, this option is automatically
recognized and cannot be changed)
N1
B5 Minute interval of RF
transmission
1: 1-30 minutes
2: 0 (set seconds on B06)
20 min
B6 Second interval of RF
transmission
3-30 seconds 30 s
RF RECEIVER INDICATOR LIGHT
GREEN LIGHT: Power-on
TEMPORARY RED LIGHT: Loading

10
IP SETTING (RF RECEIVER)
Power off state, long press “ “ for 3-5 seconds to do advanced setting. Short press
“ ” to switch and confirm. Press “ ” and “ ” to adjust options from B1 to B6. After finish
setting, standing for 5 seconds it will save setting then exit.
A1 Temperature
Calibration -9-+9
℃
0.5
℃
A2 Temp tolerance of
built in Sensor 0.5-2.5
℃
1
℃
A3 Temp tolerance of
external Sensor 1-9
℃ (NOT THIS MODEL)
2°C
A4 Children Lock 0:half lock 1:full lock 0
A5 Max temp of External
sensor
35-70
℃
(If when setting temp is lower than
35
℃
, screen display【--】, cancel high temp
protection)
(NOT THIS MODEL)
-
A6
Min temp of integrated
sensor
(anti-freeze protection)
1-10
℃
(If when setting temp is higher than
10
℃
, screen display【--】, cancel anti freeze
protection )
5
℃
A7 Min Temp Setting 1-10
℃
5
℃
A8 Max Temp Setting 20-70
℃
35
℃
A9 Descaling function
0:Close descaling function
1:Open descaling function（Function works for 3
minutes every no-operating 100 hours）
0
AA Power off Memory
when power cutting
0: Stay last state before power cutting
1: Electricity back - turn off
2: Electricity back - turn on
0
AB Weekly Programmable
Function
P1: 5+2 days
P2: 6+1 days
P3: 7 days
P1
AC Restore to factory
defaults
Display A o, long press until show the whole
screen -
7
and smartphone need to be connected at the same
Wi-Fi network. If you can, it is better to switch off temporary 5GHz networks just during
configuration.
Thermostate and Receiver are already paired. (yellow/orange light blinking when powered both
on). If any problem please enter in advanced IP settings (B3) and re-pair them. (see IP advanced
setting instructions)
STANDARD - EZ MODE
1. See “Wiring diagrams” if you haven’t done it yet and connect thermostat and receiver
to power accordingly.
2. OPTION 1 (PAIRING ON RECEIVER): Connect to the power and turn on thermostate and
receiver. Then press and hold receiver button “push” for 5-8 seconds until solid blue led
light (EZ matching mode). If blue light is blinking (AP MODE) it means it is not ready to
pair so please, please try above passage again until blue led light on receiver is solid and
continuose.
2b. Or OPTION 2 (PAIRING ON THERMOSTATE DISPLAY): Connect to
power and turn on thermostat and receiver. On thermostate press and
hold “ ” for 3-5 seconds untill the icon with text “OFF” and icon “ ”
are blinking together on display. Then short press one time “ ” to enter
into wifi config.
3. Press "Add Device" or "+" in the upper right corner to add the device and select the
device type "Smart wifi Homcloud Chronotermostat RF”
4. On your app, Click “Confirm icon rapidly blink”, then select your network and back to
your app to enter the password of your wireless router and confirm. The app will
connect automatically. This may typically take up to 5~90 seconds to complete.
5. Your room name could be edited when the device is connected and you can choose the
corresponding room location.

8
OPTION B – AP MODE – MANUAL MODE (ONLY IF STANDARD EZ MODE FAILED)
1. Same step as before to make this icon“ “ blinking. On app, click “AP Mode” on the
upper right corner.
2. Click “Confirm icon is blinking” then select your network and back to your app to enter
the password of your wireless router and confirm. The app will go into another page
with all wireless connections available.
3. Press Connect now to select the wifi signal Smartlife-XXXX of your thermostat
(thermostate hot spot).
4. Go back to your app and click “Connect now” then the app will connect automatically.
This may typically take up to 5~90 seconds to complete.
QUICK OPERATIONS – BASIC OPTIONS
NO Icon Description
A Turn ON/OFF
B 1 Short press to switch automatic mode and manual mode
2 Power on state, long press for 3-5 seconds to do programmable setting
3 Power off state, long press for 3-5 seconds to do advanced setting
C 1 Confirm value: press “ ”
2 Short press it: set time
3 Long press: Holiday mode setting: OFF close this function, ON open this
function.
D 1 Decrease value
2 Long press to lock /unlock
E
1 Increase value
2 When in Auto mode state, press or to enter into temporary
manual mode 3
Long press to check external sensor temperature
(only used for the receiver with external sensor)
9
PROGRAMMABLE MODE SETTING
6 times period setting and weekly programmable mode setting: 5+2 days (factory default), 6+1
days, 7 days
TIME SETTING: Power on state, long press “ ” 3-5 seconds to enter into first time period then
set hour, minutes, period temperature, press “ ” and “ ” to adjust values. Same for all 6
periods. After finish setting, stand for about 10 sec will save setting and exit. The most
comfortable temperature is 18°C-22°C.
- 6 times period setting -
Wake up Out door Back home
6：00 20
℃
8：00 15
℃
11：30 20
℃
Out door Back home Sleep
13：30 15
℃
17：00 21
℃
22：00 18
℃
HOLIDAY MODE SETTING
Power on state, long press for 3-5 seconds to set holiday mode setting. Press “ ” and
“ ” to change ON to OFF. Then press to switch days and temperatures, press “ ” and
“ ” to change values. Press again to confirm. If you want to close holiday mode press
“ ”.
ADVANCED OPTIONS
Power off state, long press “ ” for 3-5 seconds to do advanced setting.
Short press“ ” to switch options and confirm. Press “ ” or “ ” to adjust values.
After finish setting stand for about 5 seconds it will save setting then exit.
NO Description Range Default