Home Accents Holiday Coffin Skeleton User manual

READ AND SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTION
CAUTION
-Risk of burn, fire or electrical shock.
-For indoor use only.
-Please read instruction manual before using.
-Don’t immerse in liquid.
-Not for space heating purpose.
FOG MACHINE TECHNICAL SPECIFICATIONS
Item Code: 5724319
Model: FM1000-AH
Rating Voltage: AC120V, 60Hz
Power: 1000W
Ambient Temperature: -10 ~ 45°C
WARNING
To prevent risk of personal injury, fire, and electric shock:
● Never leave unit unattended while plugged in. Unplug when not in use.
● Read all important safety instructions and cautions.
● Connect only to a properly grounded outlet.
● Place product on a flat, level HARD surface and connect the cord to prevent the product
from overturning.
● For use only in covered areas. Keep unit dry, do not expose to rain or moisture. Do not
immerse unit.
● Leave enough space for good ventilation. Keep unit cool and away from other objects.
● Use only with SVI Fog Liquid (sold separately).
● Do not operate unit without fog liquid.
● Pour fog liquid carefully to avoid spills which could result in electrical shock. Do not use
if liquid spills onto unit. Let unit dry completely before plugging in.
● Do not overfill the liquid.
1000W Watt Coffin Skeleton
Fog Machine USER MANUAL
Fuse: 10A, 125V
Preheat Time: 3 ~ 5 Minutes
Fog Output: 3,000 CFM
Tank Capacity: 1.1 Liter
Dimensions: L411 × W211 × H250 mm
L16.1 × W8.3 × H9.8 inch
USA/ États-Unis 1004189173
YOW 1004126187

● Keep away from flames and flammable/explosive substances to avoid fire or explosions.
Never pour flammable liquids such as gas, perfume etc. into the fog machine.
● Keep product and fog liquid out of reach of children. Use only under adult supervision.
● Do not spray in the direction of flames or people. Stay at least 20 inches (50cm) from the
nozzle at the front of the unit.
● Do not obstruct the nozzle.
● Do not open unit. No user serviceable parts inside, please refer to your vendor. Only an
electrician can change the power cord.
● Clean unit before storage to avoid damages.
PARTS LIST
A. Fog Machine B. Remote
C. Power Cable D. Fog Liquid (not included)
E. Handle F. Handle Screw (2 Pieces)
illustration 1
illustration 2
A
B
F
C
DE
GENERAL ASSEMBLY AND OPERATION
INSTRUCTIONS
Please follow all directions below and as marked on the fogger while
in use:
1. Remove all the packing before use. Note: Please contact the store
if you find any broken or missing parts. Place the unit on a flat,
level surface. Plug the remote connector into the 3-pin connector
located on the back of the Fog machine.
2. Secure the handle with the handle screws. (See illustration 1)
3. Unscrew the tank lid on the reservoir tank towards the back of the
Fog Machine and pour the Fog Liquid inside. Do not spill Fog
Liquid onto the unit. Do not overfill. If liquid gets into Fog Machine,
allow unit to dry completely before plugging in. Close the lid to the
reservoir tank tightly. Always make sure there is enough Fog
Liquid in the tank before using the Fog Machine. (See illustration 2)
4. Connect the unit with proper power supply (120VAC). Turn on the
switch on the back of the unit.

WARNING: Risk of Electric Shock – DO NOT REMOVE grounding pin on plug or use
ground pin adaptors.
5. Warm up time is approximately 3 – 5 minutes. When fully heated, the light on the remote will
turn on, and then put the switch of remote to on-position to produce fog.
6. Turn off the unit before refilling the fog machine.
7. Unplug the unit when not in use.
8. To refill the tank; turn off the unit, unplug and follow the directions in Step 3.
ADDITIONAL INFORMATION
(a) It is normal for condensation to appear on the nozzle of the Fog Machine.
(b) A small amount of fog may spray during or after operation.
(c) The unit will have to reheat after long bursts of use. The unit will stop operation for a
short period in order to heat up to operating temperature again. While this is happening,
fog cannot be produced. The light on the remote will turn on again when the unit is
ready to generate more fog.
MAINTENANCE & SERVICING
Note: Use of fogger liquids not included or those other than SVI Fog Liquid are not
recommended and may result in blockage, leakage, or other damage to the unit.
INSPECTION
Before each use, check unit for any cracks in the enclosure, remote control, cords, and
plugs. Make sure there are no exposed wires. Do not use if any of the above conditions
are found.
CLEANING
Should you experience low fog output after many hours of continuous operation or after
the machine has been idle or in storage for a long time, it is recommended to run a cleaning
solution through the system to prevent the accumulation of particles in the heating element.
(a) While the unit is unplugged and cool, empty all Fog Liquid from the machine and replace
with a fog machine cleaning solution in the tank. SVI Fog Machine Cleaning Fluid
(not included) is recommended. Plug unit in and allow to warm as usual.
(b) Run unit in a well-ventilated area until tank is empty.
(c) Cleaning is now complete.
All fog machines are prone to clogging due to the consistency of Fog Liquid and the high
temperatures at which it vaporizes. However a well maintained machine should provide years
of reliable use.

STORAGE
It is important to remove all fluid from the unit when storing for an extended period of time.
1. When the unit is unplugged and cool, empty all Fog Liquid from the machine. Plug in unit
and allow to warm as usual.
2. Run unit in a well-ventilated area for 10-seconds to confirm tank is empty and dry.
3. Store on a flat, level surface. Keep in a well-ventilated, cool and dry location.
For best performance, operate unit for 10-minutes every 3 months. Follow the Operation
Instructions and Storage instructions accordingly.
FUSE REPLACEMENT
If the unit does not function at all when connected to the main power supply then it is highly
likely that the fuse has blown.
WARNING: Risk of electric shock and fire. Disconnect from main power supply
before attempting to replace fuse.
1. Turn the fuse knob counterclockwise to reveal the fuse.
2. Replace the fuse with the same size and type fuse: 10A, 125V.
3. Place fuse in cover and reinstall by turning clockwise. Be sure not to over tighten.
Congratulations on the purchase of your new fog machine!
FOR INDOOR USE ONLY
SAVE THESE INSTRUCTIONS
© Seasonal Visions International
Emeryville, CA 94608
Tel: [phone]
All Rights Reserved
MADE IN CHINA