Home Decorators Collection 1006215481 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b)Thisproduct is for indoor use only. The electrical rating0.57 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
i)Thisisanelectricproduct–notatoy! Toavoidriskoffire,burnspersonal
injuryandelectricshockit shouldnot be playedwithor placedwheresmall
children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m)Do not cover the product with cloth, paperor any materialnotpart of the
product when in use.
n) Do not move the tree by pulling the tree tips or tree branches.
o)This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows, unplug
theproduct fromtheoutlet. Also unpluganyadditionalstringsor products
that may be attached to the product. Replace the fuse as per the User
Serving instructions (follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded.
p) Read and follow all instructions that are on the product or provided with
the product.
q) SAVE THESE INSTRUCTIONS.
CAUTION! – ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
CAUTION:
1. The product consists of non-replaceable LED lamps. To reduce the
risk of fire or electric shock, do not attempt to replace lamps or
modify string.
2. This product can only be used with the original adapter, not other
brands of adapter.
7.5 ft Elegant Grand Fir LED Pre-Lit Tree with
Timer
SKU# 1006215481
Package Contents
A. Top Section
Qty: 1
B. UpperMiddle
Section
Qty:1
C. LowerMiddle
Section
Qty:1

D. Bottom Section
Qty: 1
E. Standwithan
eyebolt
Qty:1
F. PowerCord
Qty:1

G. Remote Control
Qty: 1
H. Fuse
Qty:2

I. Latch
Qty:2


Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2. Open the stand to a 90 degree angle until the hole lines up with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
Pre-Assembly

Assembling the tree
Pleaseremove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (D) into the tree stand and tighten the screw.
(See Fig. 1)
Step2. Insertlowermiddlesection(C)intothetreebottom(D).(SeeFig.2)
Step 3 Insert upper middle section (B) into the lower middle section (C).
(See Fig. 3)
Step 4. Insert tree top (A) into the upper middle section (B). (See Fig. 4)
Warning: There is a tree top connector on the tree top (A). Do
not overload. Connect other lighting strings or tree toppers
end-to-end up to a maximum of 216 Watts (1.8 Amps). Do not
interconnect low-voltage products.
Step 5. Insert the provided power cord into the connector on the tree
bottom (D) in right direction properly and tightly (always match the
protuberance of the end connector of power cord to the concave
of the connector found on the tree bottom (D) according to the
magnified drawing on fig. 5.).
Step6. Allowbranchestofallinto place orgentlypullbranchesupandout.
When adjusting branches be sure that all wires are free of branch
hinges. (SeeFig. 6)
Step 7. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and oneat the center of the main
stem. Repeat pattern for each branch. (See Fig. 7)
Step 8. Plug the power cord into a proper outlet. The plugF1 controls the
treetoplights.TheplugF2controlsthetreelights.Thistreecomes
with a control box and a remote control. You can change the
lightingpatternsofthetreebyusingcontrolboxorremotecontrol.
Please see Instructions of control box and remote control as
below.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Instruction of control box and remote
control
Instruction of control box
1. Press the ON/OFF Timer button on control box to turn on and off
timer function.
2. Press the Timer button on control box to select below timer hours:
i. Indicator lights of timer on control box turn on at 2 position:
The tree lights will automatically run through a 2-hours
ON, 22-hours OFF cycle.
ii. Indicator lights of timer on control box turn on at 4 position:
The tree lights will automatically run through a 4-hours
ON, 20-hours OFF cycle.
iii. Indicator lights of timer on control box turn on at 6 position:
The tree lights will automatically run through a 6-hours
ON, 18-hours OFF cycle.
iv. Indicator lights of timer on control box turn on at 8 position:
The tree lights will automatically run through an 8-hours
ON, 16-hours OFF cycle.
No memory mode on timer whether the tree or the timer is
re-started.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1. Press the button ON or OFF to turn on or off the lights.
2. Press the 2H, 4H, 6H or 8H button to select the different timer hours.
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Replace with a new button cell “CR2025” (3 volt) into
the compartment.
CAUTION: DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
Maintenance
Replace the fuse.
Power cord plug F1 fuse replacement (replaceable 3 amp, 125 volt fuse
is located in spare parts bag):
1. Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
2. Open fuse cover. Slide open the fuse access cover towards the
blades of the attachment plug.
3. Remove fuse carefully.
4. Risk of fire. Replace fuse only with 3 Amp,
125 Volt fuse (provided with product).
5. Close fuse cover. Slide closed the fuse access cover.
6. Risk offire.Donot replace attachment plug.Containsasafetydevice
(fuse) that should not be removed. Discard product if the attachment
plug is damaged.

CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE REPLACEMENT.
Care and Cleaning
Step 1. Before using or reusing, inspect product carefully. Discard any
productthathave cut,damaged, or frayed wire insulationorcords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
Step 2. When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, orbushes, to avoid
anyunduestrain orstressontheproduct conductors,connections,
and wires. Remove all ornaments and decorations.
Step 3. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (D) and save them.
Step4. Gentlyliftthe tree top straightuptoremove from the center section
and fold all branches towards the pole.
Step 5. Repeat this step for the center and bottom tree sections.
Step6. Carefullyplacealltreesectionsintoashippingboxandtapeitshut.
Step 7. Store your tree neatly in a cool, dry place away from sunlight.
Troubleshooting
Problem Solution
The tree or
the tree top
does not
light
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Makesurethepowercordiswellconnectedtothetree
bottom (D). Ensure that the plug F2 is plugged into the
plug F1 and then plugged into the wall outlet.
Check for blown fuses at the power cord plug F1.
Replace as needed with the replacement fuses
provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Top section
does not light
Push downward and
rotatethetopsectionto
B section to make sure
they are connected
securely.
The device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Warning: Please note that changes or modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician
for help.
CAUTION
a) Toreducetheriskofelectricshock,useonlywiththepower-supply
cord provided or with a cord set intended for outdoor use.
b) Do not use a cracked, frayed, or damaged cord. Inspect the cord
periodically.
c) Do not abuse cord – Do not carry product by the cord or yank or
pull it to disconnect from the outlet.
d) Disconnect the product from the outlet when not in use.
Loose branches
If a branch of the tree falls off, follow the steps below to
reinstall it with a spare latch (I).
1) Place the branch into the slot of the bracket.
2) Insert a spare latch
through the hole
and use diagonal
pliers (not included)
to crimp the latch.
(See Fig. A)
Importer: Home Depot
Address: 2455 PACES FERRY ROAD ATLANTA, GA 30339
Tel: [phone]
Model No. LTW36C-12V1C(0.57A)