Home International Furniture CHARLOTTE D520-05 User manual

CHARLOTTE TWIN BED
ASSEMBLY INSTRUCTIONS
Images for illustration only
Assembly Requirements
The products’ assembly system works according to the increasing
order of the indicated numbers. For example: 01, 02, 03, 04 … to the
end of the assembly.
ASSEMBLY SYSTEM
To clean your furniture, use a dry or wet cloth, and do not use
chemicals that may damage your product.
NOTICE
D520-05 White
D520-90 Gray
D520-101 Coffee
1

*Please check contents and read the instructions before commencing assembly.
*Assemble this product following the enclosed instructions carefully.
*Please take care to avoid damaging panels during assembly.
*Please assemble on a clean soft suface to avoid damage.
Please Note:
The below parts have all been stamped with the
part number to help identify them during assembly.
PARTS LIST
ITM/D520-
01
02
05
05
06
08
09
10
11
12
12
12
12
13
13
12
04
07
14
14
14
14
14
14 14
03
Item Box Qty Description Size (measurements)
(inches)
Size (measure-
ments) (mm)
01 2/2 01 Headboard upper rear frame support 38,7 x 2,2 x 0,6 982 x 55 x 15
02=05 1/2 01 Small Headboard Panel 38,7 x 4,5 x 0,6 982 x 115 x 15
03 1/2 01 Left Headboard leg 46,7 x 5,1 x 1,6 1187 x 130 x 40
04 1/2 01 Central Panel 38,7 x 4,5 x 0,6 982 x 115 x 15
05=02 1/2 02 Small Panel 38,7 x 4,5 x 0,6 982 x 115 x 15
06 1/2 01 Lower Headboard panel 38,7 x 9,3 x 0,6 982 x 235 x 15
07 1/2 01 Headboard central rear frame support 25 x 2,4 x 0,6 636 x 60 x 15
08 1/2 01 Right Headboard Leg 46,7 x 5,1 x 1,6 1187 x 130 x 40
09 1/2 01 Footboard Panel 38,7 x 9,2 x 1,0 982 x 234 x 25
10 1/2 01 Left Footboard leg 18,3 x 3,9 x 1,6 465 x 100 x 40
11 1/2 01 Right Footboard leg 18,3 x 3,9 x 1,6 465 x 100 x 40
12 2/2 05 Foundation Support Brace 40,1 x 1,7 x 0,8 1018 x 43 x 21
13 2/2 02 Side Rails 75,6 x 5,1 x 1,0 1920 x 130 x 25
14 2/2 07 Sltas 72 x 2,4 x 0,4 1830 x 60 x 11
2

ITM/D520-
FITTINGS LIST
08x
39x
04x24x
08x10x08x
A
I
HF
DCB
Screw 1/4x3.1/2 (90mm)
Ringed Nails 12x12mm
Shoe
Dowel 8x25mm
Screw 4,0x25mm CHT.Screw 4,5x50mm CHT.Screw 4,5x60mm FLA.
18x
08x
08x08x
G
J
NM
Cylindrical nut
Half moon nut
16mm hole plugs12mm hole plugs
10x
Bolt cover adhesive 10mm
E
04x10xLK
Rails holding supportSlats holding support
3

Pre-Assembly ITM/D520-
2x
5x
01
02 05
04
06
09
12
G
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
G
G
G
G
G
G
G
G
G
G
24x
F
Dowel 8x25mm
18x
G
Cylindrical nut
4

Pre-Assembly ITM/D520-
H
H
H
H
I
I
I
I
03
08
10
11
04x04xIH
Ringed Nails 12x12mmShoe
5

ITM/D520-
01
02
03x
D
Screw 4,0x25mm CHT.
1
D
D
D
6

ITM/D520-
04
06
05
05
03
2
BM
M
M
B
B
03x
B
Screw 4,5x60mm FLA.
03x
M
12mm hole plugs
3
7

05x
D
Screw 4,0x25mm CHT.
ITM/D520-
4
DDDD
D
07
8

03x
B
Screw 4,5x60mm FLA.
03x
M
12mm hole plugs
ITM/D520-
5
M
M
M
B
B
B08
9

ITM/D520-
6
7
02x
B
Screw 4,5x60mm FLA.
02x
M
12mm hole plugs
M
M
B
B
09 10
11
10x
C
Screw 4,5x50mm CHT.
10x
Bolt cover adhesive 10mm
E10x K
Slats holding support
C
C
C
C
CC
C
C
C
C
E
E
E
E
E
E
E
E
K
K
K
K
K
K
K
K
K
K
13
13
12
12
12
12
12
10

ITM/D520-
8
L
L
A
A
A
A
N
N
N
N
J
J
J
J
08x
A
Screw 1/4x3.1/2 (90mm)
08x08x
J N
Half moon nut 16mm hole plugs
04x
L
Rails holding support
9
L
L
A
A
A
A
N
N
N
N
J
J
J
J
11

ITM/D520- Rev.001
10
III
35x
I
Ringed Nails 12x12mm
Recommended evenly distributed maximum weights.
14
14
14
14
14 14 14 14 14
14
I
I
I
I
12