Home Styles 88 5061 761 User manual

Part List (in this carton)
B.
Side Frame
1 pc.
C.
Side Frame
1 pc.
F.
Stretcher
1 pc.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
88 5061 761
Storage Stand
For assembly see instructions in carton 88 5061 762
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
IMPORTANT NOTE.
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.

Hardware List
Hex Wrench
1 pc. M6x12
Head Cap Bolt
(short)
12 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
Part List (in this carton)
D.
Shelf
4 pcs.
E.
Support
4 pcs.
A.
Top
1 pc.
Spring Washer
20 pcs. (+1 extra)
Flat Washer
20 pcs. (+1 extra)
M6x16
Head Cap Bolt
20 pcs. (+1 extra)
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Also need the Parts in carton 88 5061 761
M4x32
Wood Screw
12 pcs. (+1 extra)
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit, Level
88 5061 762
Storage Stand
IMPORTANT NOTE.
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.

Assembly Instructions 2/4
STEP 2
Attach Shelves (D)
to unit with Flat Washers,
Spring Washers and
Head Cap Bolts,
tightening the bolts only half way.
Tighten all Head Cap Bolts
used in Steps 1 and 2.
STEP 1
IMPORTANT
* Do not tighten all the Head Cap Bolts until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
Figure 1
Figure 2
Place Top (A) upside down on a soft cloth.
Attach Side Frames (B) and (C) to Top (A)
with Head Cap Bolts (short),
tightening the bolts only half way.
(See Figure 1)
Attach Stretcher (F) to unit with
Flat Washers, Spring Washers and Head Cap Bolts,
tightening the bolts only half way.
(See Figure 2)
B
C
F
A
Head Cap Bolt
(short)
D
D
D
D
Head Cap Bolt
Head Cap Bolt
Spring Washer
Spring Washer
Flat Washer
Flat Washer

Assembly Instructions 3/4
To level the unit, adjust the adjustable
levelers on the bottom of unit. (See Figure 3)
Note: Unit must be level to work properly.
(Figure 3)
STEP 3
Attach Supports (E)
to unit with Wood Screws.
Turn the unit over to its’ upright position.
STEP 4
E
E
E
E
Wood Screw

Assembly Instructions 4/4
Wall Screw
M4x16
Machine Screw
1 pc.(+1 extra)
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
Drill 3/8” hole in wall
Top of unit
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
M3.5x40
Wall Screw
1 pc.(+1 extra)
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Machine Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight. Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
Machine
Screw