HOME2US SMP-6200 User manual

DIGITAL SET-TOP-BOX
Irdeto CA Satellite Receiver
SMP-6200
USER’S MANUAL

Digital Satellite Receiver SMP-6200
Table of Contents
1.PRE-INSTALLATIONCHECKUP 3
2.SAFETYWARNINGS 4
3.CONNECTIONS 6
4.REMOTECONTROL 8
4.1 Remote Control Unit 9
5. MENU INSTRUCTION 10
5.1MainMenu 10
5.1.1TVGuide 11
5.1.2 Radio Guide 11
5.1.3Installation 12
5.1.3.1Installation 12
5.1.3.1.1 Antenna Setting 13
5.1.3.1.2 Auto Searching 17
5.1.3.1.3 Manual Searching 18
5.1.3.1.4 Factory Default 24
5.1.4 Channel Management 24
5.1.4.1 Favorite/Lock Channel 25
5.1.4.2EditChannel 25
5.1.4.2.1 Move 26
5.1.4.2.2 Delete 26
5.1.4.2.3 Rename 27
5.1.4.3DeleteTP 27
5.1.5SystemSetting 28
5.1.5.1 Time Setting 28
5.1.5.2 A/V Output 28
5.1.5.3 Parental Control 29
5.1.5.4Timer 31
5.1.5.5 Power up Channel 31
5.1.6SystemInformation 32
5.1.6.1 CA Status 32
5.1.6.2 IRD Status 33
5.1.6.3 Load Status 33
5.1.6.4 Mail Message 34
5.1.6.5 Announcement 34
5.1.6.6 Upgrade software 34
6.SPECIFICATIONS 35
6.1Compliance 35
6.2MajorFeatures 35

2
Digital Satellite Receiver SMP-6200
1. PRE-INSTALLATION CHECKUP
Please check the following items after opening the package: digital satellite receiver, remote control, battery, A/V cable,
RF cable, and user’s manual. Please keep the packing box, packing materials, and plastic bag in safe place for
repackaging in the future.

3
Digital Satellite Receiver SMP-6200
2. SAFETY WARNINGS
The normal operating temperature of the digital satellite
receiver is between 0ºC and 40ºC.
Please prevent the receiver from operating in dusty
conditions.
The receiver shall be operated in ventilated environment
away from heat sources.
Do not open or disassemble the outer chassis in order to
avoid the danger of electric shock and damaging to the
receiver. Opening the chassis will also void the warranty.

4
Digital Satellite Receiver SMP-6200
The satellite antenna that is connected to the receiver shall
be equipped with anti-shock device from lightning.
When the receiver is inoperative, please consult the
Customer Support.

5
Digital Satellite Receiver SMP-6200
3. CONNECTIONS
Please refer to Figure 1 and Figure 2 for the following instructions. Connect the LNB cable from the dish antenna to the
LNB IN connector on the back of the digital satellite receiver. Use the RCA audio/video cables to connect the Audio
Left, Audio Right, and Video Output to the corresponding connectors on TV.
Figure 1 Front Panel
POWER/ESC To switch between standby and power-on states.
ef To adjust the volume output of the receiver when receiving TV programs, or change parameters
within the menu.
cd When receiving TV programs, pressing these keys switches to the next higher or lower numbered
program, or to move the scroll bar up or down on the menu.
MENU To bring up the main menu, or exit from menu or submenu.
SELECT To enter the next lower level submenu or to confirm the parameter value entered.

6
Digital Satellite Receiver SMP-6200
Figure 2 Rear Panel
LNB OUT Satellite signal loop through terminal
LNB IN Satellite signal input terminal from LNB
RS-232 RS-232 serial port
S-VIDEO Connect to S-VIDEO Jack of the TV or VCR
VIDEO (Yellow) Line signal output of video
AUDIO (White) Line signal output of left audio channel
AUDIO (Red) Line signal output of right audio channel
DIGITAL AUDIO Connect to digital amplifier
RF OUT RF signal output to TV
PAL CH21-69 NTSC CH3-4
RF IN RF signal input from ANT or CATV system
AC 90-240V AC power cord
50Hz/60Hz
POWER Receiver power switch

7
Digital Satellite Receiver SMP-6200
4. REMOTE CONTROL
KEY FUNCTION
POWER Turns power ON/OFF of the receiver.
MAIL Directly goes into mail screen.
TV/AV Switch output between TV, AV and VCR.
TV/RADIO Switches between TV and Radio mode.
0~9 Enters number of the required menu item or
selects a channel number to watch.
SIGNAL Displays the signal strength and quality
information.
FAVLIST Displays the favorite channel list.
FAV+ / FAV- Moves up/down in the favorite channel list.
TIMER Calls up Timer Recording Table.
EPG Calls up the EPG (Electronic Program Guide).
AUD Selects the audio input mode.
INFO Displays the selected channel information in TV
guide screen or radio guide screen.
PRV Returns to the previous channel.
R/L Selects the different audio output modes.
EXIT Exits from current menu/submenu.
MENU Presses this key one time to run menu on screen
and calls command box.
OK Executes the selected item in the menu screen, or
enters the desired value in any input mode.
CH+, CH- These keys are used to switch to the next higher
or lower program, or to move the scroll bar up or
down in the menu.
VOL+, VOL- These keys are used to adjust the volume output
level of the receiver, or to select the next
available parameters within the menu.
MUTE This key is used to toggle in or out of muting
mode.
Figure 3 Remote Control
TELETEXT Display teletext, if there is teletext information in
stream.

8
Digital Satellite Receiver SMP-6200
4.1 Remote Control Unit
Please refer to the following diagram (Figure 4) when using the remote control. The maximum distance for usage is 10
meters (30 feet) with look angle 60 degrees. Please aim the infrared transmitter in the front of the remote control to the
front panel of the receiver.
Figure 4 Remote Control Unit Range

9
Digital Satellite Receiver SMP-6200
5. MENU INSTRUCTION
5.1 Main Menu The contents of main menu are as follows:
Main Menu
Installation
Channel Management
System Setting
System Information
 Move Select Exit
OK EXIT
Installation
Installation is used to search for new services or to edit existing ones. It can also be used to load the default setup of the
receiver.
Channel Management
This is used to edit the downloaded channels, to set the favorite channels and to lock channels. User can also delete the
stored TP.
System Settings
The system settings provide a convenient way of selecting different power-up channels, adjusting the time and A/V
output mode, and adjusting parental control rating.
System Information
System information provides all information regarding the receiver, including CA, loader, mail message, announcement,
and all details of the upgraded software.

10
Digital Satellite Receiver SMP-6200
5.1.1 TV Guide This shows the list of TV program, press OK button can enter to TV guide.
You can select one of the TV programs (event name) by pressing c/dkeys follow with pressing the OK key.
You can press the Info button to show the channel information.
8. Suroyo TV
7. CMC
6. HRT
5. CGNTV
4. Planeta TV
3. VPTV
2. TV TWRAM
1. Lawyers TV
Main Menu
TV Guide
5.1.2 Radio Guide This shows the list of Radio program, press TV/Radio key to change the options between
“TV guide” and “Radio Guide” in TV guide screen.
You can access one of the Radio programs (event name) by pressing c/dkeys follow with pressing the OK key.
You can press the Info button to show the channel information.
2. Radio 2
3. Radio 3
4. Radio 4
5. Radio 5
6. Radio 6
7. Radio 7
8. Radio 8
1. Radio 1
Main Menu
Radio Guide

11
Digital Satellite Receiver SMP-6200
5.1.3 Installation
Installation is used to search for new services or edit existing ones. It can also be used to load the default setup of the
receiver.
To enter this menu, you have to input the PIN Code first. The default PIN Code is 0000.
Main Menu
Installation
Channel Management
System Setting
System Information
xx
Please Input Your Password
Message Box
 Move Select Exit
OK EXIT
5.1.3.1 Installation This menu provides all the settings for customizing. There are two ways in searching
new services, auto search and manual search. Resetting to default setup is also set in this
menu.
Installation
Main Menu
Antenna Setting
Auto Search
Manual Search
Factory Default
 Move Select Exit
OK EXIT

12
Digital Satellite Receiver SMP-6200
5.1.3.1.1 Antenna Setting
You can select the Antenna and LNB settings for service searching, as well as the settings of 22KHz tone and DiSEqC
switch and dish options. There are 32 possible antenna settings. The values set in this menu are available for selection in
other Service Searching Menus. LNB type has two options to switch to, normal and universal. If normal is selected,
there will be only one Freq available. If universal is selected, there will be two frequencies provided to be selected, i.e.,
LNBF Freq low and LNB Freq High.
Antenna Setting
Installation
Main Menu
●
A
ntenna AMC-4 
●LNB T
yp
e Normal 
●Fre
q
uenc
y
12120
●LNB Powe
r
ON 
●22KHz AUTO 
●DiSE
q
COFF 
●Dish FIXED 
●Save ●Auto Search  Move OK
OK
●Save & Exit
Select Exit
EXIT
Press c/dkeys to choose between the following items, press e/fto change its value. Press OK to show all available
options.
Antenna It shows the satellite name. User can select the satellite name by pressing e/fkeys. The total
number is 32.

13
Digital Satellite Receiver SMP-6200
LNB Type There is two options to be selected from: normal and universal. Press e/fkeys to switch between
the options. If normal is selected, the figure is as above, if the universal is selected, the figure is as
following:
Antenna Setting
Installation
Main Menu
●
A
ntenna AMC-4 
●LNB T
yp
e Universal
●LNB Fre
q
Low 9750
●LNB Fre
q
Hi
g
h10600
●LNB Powe
r
ON 
●22KHz AUTO 
●DiSE
q
COFF 
●Dish FIXED 
●Save ●Auto Search  Move OK
●Save & Exit
Select Exit
OK
EXIT

14
Digital Satellite Receiver SMP-6200
Frequency When the LNB Frequency is single, press OK to display the list of Frequency, then press c/dkeys
to select. User can always select “user defined” to add a new Frequency.
Antenna Setting
Installation
Main Menu
●
A
ntenna AMC-4 
1. 5150
2. 9750
3. 10600
4. 10700
5. 10750
6. 11200
3. 10600
●LNB T
yp
e Normal 
●Fre
q
uenc
y
12120
●LNB Powe
r
ON 
●22KHz ON 
●DiSE
q
COFF 
●Dish FIXED 
●Save ●Auto Search  Move OK
OK
●Save & Exit
Select Exit
EXIT
LNB Power Press e/fkeys to switch the LNB Power between ON and OFF.
22KHz When LNB type is set to normal, 22KHz has two different options: ON and OFF. When LNB type is
set to universal, 22KHz will be auto selected. Press e/fkeys to change between the options. Set
OFF to select dual-LNB or set ON to select two antennas connected to a 22KHz tone switch.
DiSEqC According to the option and position of DiSEqC switch, you can select from Ato Dof DiSEqC and
turn it OFF.
Dish Press e/fkeys to switch between the options fixed and motor. Setting to fixed, the dish can not be
moved. Setting to motor, the dish will be movable.
Help Menu Press c/dkeys to select between the following items, presse/for input 0~9 to change its value:
press OK to show all available options.
Press Red key on remote to save the settings. The saved message will be displayed. After saving, this menu will remain
the same.

15
Digital Satellite Receiver SMP-6200
Antenna Setting
Installation
Main Menu
●
A
ntenna AMC-4 
●LNB T
yp
e Normal 
●Fre
q
uenc
y
●LNB Powe
r
●22KHz
●DiSE
q
C
11300
13/18V 
AUTO 
OFF 
Saving data, Please wait…
Message Box
●Dish FIXED 
●Save ●Auto Search  Move OK
OK
●Save & Exit
Select Exit
EXIT
Press Blue key on remote, the setting will be saved and meanwhile it returns to the previous menu.
Press Green key on remote, it will directly get into auto search menu.

16
Digital Satellite Receiver SMP-6200
5.1.3.1.2 Auto Searching
To enter this menu, user can press OK key from the installation screen. There are two bars on the bottom to indicate the
signal strength and quality. The bars in green color show the signal is in good condition. This menu will automatically
search for the existing channels by the frequencies.
Auto Search
Installation
Main Menu
●Satellite AMC-4
●Fre
q
uenc
y
12120 
●Scan mode All 
●Start Scan  Move OK
OK
●Antenna Setup  Select Exit
EXIT
Satellite It shows the satellite name. User can select the satellite name by pressing e/fkeys. The total
number is 32. Press OK key to show all satellite lists.
Frequency It shows the frequency of the transponder user selected. The corresponding symbol rate and
polarization that have been confirmed. Press OK to display the list of existing frequencies.
Scan Mode It shows two scan modes in this entry by pressing e/fkey. Set scan mode to all, all the channels in
the transponder you selected will be download if the signal is locked. Set scan mode to FTA, only
free-to-air channels can be downloaded.
Help Menu Press c/dkeys to select between the following items, presse/for input 0~9 to change its value:
press OK to show all available options.
Press Red key on remote to get into search menu.
Press Blue key on remote to return to antenna setting menu.

17
Digital Satellite Receiver SMP-6200
5.1.3.1.3 Manual Searching
After setting the search parameters like frequency, symbol rate etc, you can find the services in the transponder you
selected. There are two bars on the bottom to indicate the signal strength and quality. The bars in red color show the
signal is in good conditions.
Manual Search
Installation
Main Menu
●Satellite AMC-4 
●Fre
q
uenc
y
12120 
●S
y
mbol Rate 30000
●Polarization V
60%
76%
●Start Scan ●Edit TP  Move OK
●Antenna Setup
●Scan Mode All 
●Network Search Off 
●PID Search Off 
Strength
Quality
OK
 Select Exit
EXIT
You can press c/dkeys to select between the following items, press e/fkey or 0…9 to change its value.

18
Digital Satellite Receiver SMP-6200
Satellite It shows the satellite name. User can select the satellite name by pressing e/fkeys. The total
number is 32. Press OK key to show all satellite lists.
Manual Search
Installation
Main Menu
●Satellite AMC-4
Galaxy 16
IA 5
Galaxy 3C
IA 6
AMC-1
2. 9750
A
MC-4
●Fre
q
uenc
y
12120 
●S
y
mbol Rate 30000
●Polarization V
●Scan Mode All 
●Network Search Off 
●PID Search Off 
60%
Strength
76%
Quality
●Start Scan ●Edit TP  Move OK
OK
●Antenna Setup
 Select Exit
EXIT

19
Digital Satellite Receiver SMP-6200
Frequency It shows the frequency of the transponder user selected. Press OK to display the list of existing
frequencies. If the frequency exists in the list, the corresponding symbol rate and polarization are also
confirmed.
Manual Search
Installation
Main Menu
●Satellite AMC-4 
●Fre
q
uenc
y
12120 
2. 3706
3. 3760
4. 3840
5. 3860
6. 3880
1. 4000
1. 4000
●S
y
mbol Rate 30000
●Polarization V
●Scan Mode All 
●Network Search Off 
●PID Search Off 
60%
Strength
76%
Quality
●Start Scan ●Edit TP  Move OK
OK
●Antenna Setup
 Select Exit
EXIT
When user selects new TP stored on the bottom of the list, user can input the frequency by using digital keys from 0 to 9;
furthermore, the symbol rate and polarization also need to be input by user. User can set the polarization of the
transponder to Horizontal or Vertical. In horizontal case, the 18V and in vertical case, the 13V are output through LNB
line.