HOMEDEPOT Merra CFN-1032 User manual

Read completely before installation & use and keep for future reference
CFN-1032 Ceiling Fan
User Manual
V20200306

1
TABLE OF CONTENTS
INTRODUCTION
Introduction ·················································································· 1
Package Contents ········································································· 2
Safety Information·········································································· 3
Preparation ·················································································· 4
Bracket Installation········································································· 5
Downrod Mounting········································································· 6
Electrical Connections ···································································· 7
Receiver Installation ······································································· 8
Fan Blades Installation···································································· 8
Remote Control Operation ······························································· 9
Troubleshooting ···········································································10
Contact Information·······································································10
Before beginning installation of this product, read the package list on page 2 and ensure all
parts are present and display no defects. If any part is missing or damaged, contact customer
service and do not attempt to install the product. Read all of the safety information on page
3 before installation or use.
Estimated assembly time: 120 minutes.
Additional tools required for assembly:
Electrical tape, flathead & Phillips screwdriver, pliers, safety glasses, step ladder, and wire
strippers.
Additional helpful tools:
AC tester light, tape measure, wiring handbook, and wire cutters.

2
Fan Blades (×3) Remote Control
Receiver
Mounting Bracket
Balance Kit
Wood Screw (×4) Wiring Caps (×6)
Metal Washers (×4)
Spring Washers (×4)
Joint Screws
Star Washers (×4) Bolts (×2)
Canopy
Downrod Coupling Cover Canopy Cover
Decorative Cover Kit
Fan Motor Assembly
TABLE OF CONTENTS

3
1. To reduce the risk of electric shock,ensure electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with national and local electrical codes. Electrical
installation should be performed by a qualified licensed electrician.
3. This fan is suitable for use with solid-state speed controls.
4. To reduce the risk of personal injury, use only the screws and washers provided with
the outlet box for mounting to the outlet box. Most outlet boxes commonly used for
the support of lighting fixtures are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
5. The outlet box and support structure MUST be securely mounted and capable of reliably
supporting a minimum of 50 pounds. Use only UL listed outlet boxes marked "FOR
FAN SUPPORT".
6. After marking electrical connections, spliced conductors should be turned upward and
pushed carefully up into outlet box. The wires should be spread apart with the grounded
conductor and the equipment-grounding conductor on one side of the outlet box.
7. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of
the blades to the floor.
8. Do not use the reverse switch while the fan blades are in motion. To prevent damage
and ensure long use, the fan must be turned off and the blades stopped before
reversing direction.
9. Do not place objects in the path of the blades.
10. Exercise caution when working around or cleaning the fan.
11. Use a soft dry cloth to clean the fan body and blades. Do not use water or detergent.
12. The electrical diagrams provided herein are for reference only. Light kits that are not
packaged with the fan must be UL listed and suitable for use with this fan. Switches must
be UL general use switches. Refer to their separate instructions for proper assembly.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY,
MOUNT FAN TO OUTLET BOX MARKED “ACCEPTABLE FOR FAN SUPPORT”.
SAFETY INFORMATION
Warning!
NEVER BEND THE BLADE BRACKETS/FLANGES FOR ANY REASON.

4
PREPAR ATION
1. Turn Off Your Power
Begin installation by removing fuses or turning off circuit
breakers to the wiring you will be using. Use your compatible
UL listed junction box if you already have one installed.
2. Choose Your Mounting Position
If you need to install a new UL listed junction box, secure it
directly to your building's structure usingappropriate fasteners
and materials. Do not use plastic boxes. The outlet box and its
supports must be able to support the MOVING weight of the fan
(at least 50 lb.) and be rated for fan support.
3. Choose a Suitable Location
Ensure the blades will be at least 30 inches from any
obstruction and at least 7 feet above the floor.
Failure to disconnect the power supply prior to
installation may result in serious injury or death.
Use only on flat ceilings
Do not use on slanted surfaces
7 feet
30 inches

5
Loosen the screws on the fan hanger and fix the fan hanger to the ceiling outlet box with the
wood screws and spring washers. Pass the electrical supply wires through the center hole
in the mounting bracket.
BRACKET INSTALLATION
Junction Box
Ceiling Mounting Bracket
Hook
110V Wires
Mounting Screws
(supplied with the junction box)
Washers

6
DOWNROD MOUNTING
Pin
Downrod
Clip
×2
Set Screw
×2
Hitch Pin Retaining
Clip
Downrod
Canopy
Canopy Cover
Coupling Cover
Downrod
Canopy
Canopy Cover
Coupling Cover
Slot
Step 1: Remove the pin
and clip from the downrod.
Then partially loosen the
two steel screws in the
yoke at the top of the
motor assembly.
Step 2: Carefully place the
canopy, canopy cover, and
coupling cover onto the
downrod. Feed the lead
wires from the fan motor
through the downrod.
Step 3: Install the downrod
onto the yoke, aligning the
holes, inserting the pin
through the downrod, and
reinstalling the clip. Then
tighten the steel screws.
Step 4: Place the downrod's mount into the bracket on
the outlet box. Rotate the entire assembly until the tab
has dropped into the mount's slot and locked firmly into
place. The motor assembly should no longer rotate if
seated properly.
Failure to reattach the hitch pin and/or properly seat the
downrod can cause the fan to fall from the ceiling
during operation.
DO NOT use the fan before ensuring it is properly
secured and the motor can no longer rotate.

7
ELECTRICAL CONNECTIONS
Receiver
Ceiling
Mounting
Bracket
White (neutral)
Green or Bare
Copper (ground)
White (“AC IN N”)
Outlet Box
Black (hot)
Receiver Head
Black (“AC IN L”)
White (neutral)
Green (ground)
White (neutral)
Black (motor)
Red (for L)
Receiver
Red (for L)
Gray
(for N)
Gray (for N)
Black (“to motor L”)
GREY
Ensure there are no loose wires or connections,
and secure connectors with electrical tape.
Step 1: Insert the receiver into the tray with the
receiver facing the ceiling. For best performance,
make sure the white antenna on the end of the
receiver remains extended and not tangled with
any of the electrical wires.
Step 2: Connect the 4 colored wires from the
remote receiver to the 4 identically colored lead
wires from the fan motor. Secure each set with
the provided wire nuts.
Step 3: Connect the 2 colored wires from
the remote receiver to the 2 identically colored
lead wires from the outlet box. Secure each set
with the provided wire nuts.
Step 4: Connect the green or bare copper ground
wire from the outlet box to the ground wires from
the ceiling mounting bracket and the ceiling fan.
Separate the white and green connections from
the black wire connections, which should be kept
on opposite sides of the outlet box.
Again, ensure that the power has been
cut before working with the wiring. Use
the wire nuts provided with your fan.

8
RECEIVER INSTALLATION
FAN BLADE INSTALLATION
Receiver
Ceiling Mounting
Bracket
Outlet Box
Tuck all the connections neatly into the
ceiling outlet box. Slide the canopy up
to the mounting bracket and place one
of the key hole slots over the mounting
screw on the mounting bracket. Tighten
the screws.
Step 1: Install a blade on the main machine.
Step 2: Lock a washer ring inside the blade and tighten
the screws.
Step 3: Fix the remaining two blades on the main engine
and adjust the clearance between the blades.
Step 4: Install the decorative cover, pushing up and
turning.
Screw
Screw
Decorative Cover Kit

9
REMOTE CONTROL OPERATION
Start the fan at the indicated speed level from
low (1) to high (6)
Turns off the fan
Run the fan for the indicated number of hours
and then turns it off
Reverses the fan's direction
Key Function
1
2
3
4
5
6
Install the remote control holder onto any wall or suitable
flat surface using the two steel screws. Upon first use, connect
the remote control to its receiver in the fan by holding the
remote's button. There should be a beep to announce that
the remote has successfully connected to its receiver.
DO NOT press the button while the fan is in operation. Turn it off and wait for the blades
to fully stop their movement before reversing their direction.
This remote operates with a range of 30 feet (10 m). It uses 2 1.5V AAA batteries (not
included). If the remote will not be used for a prolonged period, it is recommended to
remove the batteries for better service life.

10
TROUBLESHOOTING
CONTACT US
Potential Problems
Fan blades
don't rotate
Fan is too noisy
Fan wobbles
during use
Common Solutions
Check fuses and/or circuit breakers and reset if needed.
Cut off power to the fan and check its internal electrical
connections.
Replace the remote control batteries.
Check that the fan cover is correctly placed and no screws
interfere with the movement of the blades.
Contact customer service to replace a faulty remote control.
Check that all screws and fasteners are well tightened.
Ensure the canopy housing has a short distance between
itself and the ceiling.
Upon initial installation, allow 24 hours of use for the machine
to break itself in.
Cut off power to the fan and check that the wire nut connections
are not rubbing against one another or the inner housing.
If you have installed a solid-state variable-speed control, cut
off power to the fan and disconnect this control from the
device. See if using the remote resolves the problem, which
can be caused by erratic signals from such controls.
Check that all screws and fasteners are well tightened.
Use the provided blade balancing kit to adjust the blades if
their tips are found to be an unequal distance from the ceiling
while well fastened.
Exchange the position of the various blades.
Again, do not bend the blades during any of these procedures.
Thank you for your purchase! If you have any questions or concerns, don’t hesitate contact us
at [email protected]. We'll resolve your problem ASAP! Customers are always the
best teachers to keep us growing!