HOMEDEPOT SHARON User manual

WARNING :
READ AND SAVE THESE INSTRUCTIONS. Follow these instructions carefully and be mindful of all warnings shown
throughout.
SHARON
Owner’s Manual
UL
R
KGS.
LBS.
Net weight

WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE
FOLLOWING:
READ AND SAVE THESE INSTRUCTIONS
1. Use this unit only in manner intended by the manufacturer. If you have questions, contact the
manufacturer at the address or telephone number listed in warranty.
2. Before servicing or cleaning unit, or installing a light kit, switch power off at service panel and look
service panel to prevent power from being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
5. If the fan will be mounted to ceiling box, the box and its support must be able to support the moving
weight of the fan (at least 40 lbs.) The box must not twist or work loose.
WARNING :
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET
BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH
OUTLET BOX.
6. If the fan will be mounted to a ceiling joist, the joist must be able to support the moving weight of the
fan (at least 40 lbs.)
7. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
8. This unit must be grounded.
9. After installation is complete, make sure that all connections are secure to prevent the fan from falling.
Make sure all wire connections are secure, and that there are no exposed conductor strands.
10.
11. Make sure that your installation will not allow the fan to come into contact with any adjacent obstacles
such as doors, hanging lamps, etc.
12. If you are installing more than one ceiling fan, do not mix the blade sets.
13. The fan must be mounted with at least 7 feet of clearance between fan blades and floor.
14. This fan is suitable for OUTDOOR locations.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE
BRACKETS WHEN INSTALLING THE BRACKETS, BALANCING THE BLADES, OR CLEANING THE
FAN. DO NOT INSERT FOREIGN OBJECTS IN BETWEEN ROTATING FAN BLADES.
WARNING: THE USE OF ANY SPEED CONTROL NOT SPECIFICALLY APPROVED FOR THIS FAN
COULD RESULT IN FIRE, ELECTRICAL SHOCK, OR PERSONAL INJURY.
3. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
4. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
P1

OFF OFF OFF
Turn off power at breaker box
to avoid possible electrical
shock.
Use metal outlet box suitable for
fan support.
Secure outlet box directly to the
building structure using ceiling joist
screws (included).
Outlet box must support 40 lbs min.
Install mounting bracket to
outlet box in ceiling using
washers and the screws
provided with the outlet box.
Outlet Box
Mounting Bracket
4.
3.
1.Unpack and inspect fan carefully to be certain all contents are
included.
2.
P2
Yoke
Cotter Pin
Cross Pin
Downrod
Wires
Canopy
Downrod Set Screw
Cross Pin
Yoke
Downrod
5a-1. Yoke & Downrod Assembly
(1) Feed motor lead wires through yoke cover, canopy
and and insert downrod into yoke.downrod
(2)Insert the cross pin through Yoke & Downrod
and secure with Cotter Pin.
(3)Tighten both Downrod Set Screws to further
secure Downrod, then pull down the yoke
cover to coveryoke
Yoke cover
Cotter Pin
Gasket
And make sure the gasket ( for wet location only ) on
top of ball is properly inserted for effective water proofing.
( for wet location only )
Fan assembly
Blade holder
Blade
Mounting Bracket
Canopy
Downrod
Hardware bag
Spring Washer 2 pcs
Lock Washer 2 pcs
Wood Screw 2 pcs
Blade Screw 16pcs
Rubber Washer 16pcs
Pull Chain Knob 2 pcs
Blade Balance Kit 1 pc
Motor screw 11 pcs
Canopy set screw 3 pcs
Wire nut 3 pcs
Light kit fitter
Yoke cover

5b-1. Making wire connection ( for 110~120VAC/60Hz )
P3
Lift fan assembly onto mounting bracket. Carefully lift fan assembly onto mounting bracket.
Rotate fan so that the notch on the ball engages the
ridge in the mounting bracket.
5a-2. Hanging the fan
Ball Notch
Mounting
Bracket
White White
(Motor-N)
Black Black
(Motor-L)
Blue
Green
Green
Green
From House From Fan
Secure with twist - lock wire nuts. (Included)
(AC-N)
(AC-L)
( for light kit )
( from downrod & motor )
( from mounting bracket )
( for ground wire )
Follow diagram below and make sure that all exposed wires are secured inside wire nuts.
Note : Wires from house may vary in color and may not include ground wire ( green ). After wiring
is completed, gently push wires into junction box with nuts pointing upward.
Make sure that all exposed wires are secured inside wire nuts.
Gently push wires into Mounting bracket with nuts point upward.
Attach blade to blade arm with screws
& washers provided in hardware bag.
Make sure that all Screws are firmly
tightened.
7. Blades installation Screws
Washers
Blade arm
1.Push up the Canopy until the two screws on mounting
bracket are engaged with Key Holes in canopy.
2.Rotate the canopy slightly until the two screw heads
are in the small end of the Key Holes.
3.Tighten both screws.
6. Canopy installation
Canopy
Remote
Control
Receiver
Mounting
Bracket
Canopy
Key Holes
Screw

P4
2.Attach the blade assembly to motor using
motor screws from hardware bag.
NOTE: Do not bend blade or blade arm to
prevent wobble.
8. Blade assembly to motor
Motor
Blade Assembly
Motor screw
Motor stopper
1.Remove 3pcs of motor stoppers.
10. LIGHT KIT INSTALLATION
(1)
Install bulbs
to lamp holders.
( max. 60Wx4 )
(2)
Connect pull chain knob
to pull chain.
Switch Housing
Screw
Nut
Switch Housing
Cover
Blue Wire
Black Wire
Light Kit
Fitter
9. Make wire connections for light kit
White Wire
White Wire
11. Turn on the power, your fan is ready for operation.
Loosening 3 screws from the switch housing cover of light kit.
( 1 ). White wire from Light Kit to white wire from fan
and connect by wire nut.
( 2 ). Black wire from Light Kit to blue wire
from fan and connect by wire nut.
Attach light kit cover and light kit assembly to switch housing by 3 original screws.