Homeworks 75-101-BTC User manual

Homewerks.com
DIMMABLE LED
MIRROR WITH
BLUETOOTH®
SPEAKERS
MODELS 75-101-BTC, 75-101A-BTC
Español p. 9
12/30/2020
U.S. Pat. No. 9,398,357
The BLUETOOTH®word mark and logos are registered trademarks owned by BLUETOOTH SIG, Inc. and any use of the said
mark by Homewerks Worldwide is under license. Other trademark and trade names are those of their respective owners.
Questions, problems, missing parts? Before returning to the store, call our customer
service department at 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
READ AND SAVE THESE INSTRUCTIONS
ATTACH YOUR RECEIPT HERE
Serial Number _______________ Purchase Date ______________
Conforms to UL Standard 962

2Homewerks.com
PACKAGE CONTENTS
A
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment.
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modications or changes to this equipment. Such
modications or changes could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Compliance
HARDWARE INCLUDED (not shown actual size)
AA BB CC DD EE
Mounting Screw Drywall Anchor Wire Connector Z-bar Locking screw
Qty. 3 Qty. 4 Qty. 3 Qty. 1 Qty. 1
PART DESCRIPTION QUANTITY
A LED mirror 1

3
Homewerks.com
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package and
hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement parts.
Estimated Installation Time: 30 minutes
Tools Required for Assembly (not included): Tape Measure, Phillips Screwdriver, Hammer, Electric Drill,
Drill Bits, Level.
Please follow all local electrical codes and consult an electrician when wiring this product.
WIRING DIAGRAM
Installation may vary depending on how the previous mirror was installed and the presence of the power
source. Supplies necessary for installation of your new mirror are not all included; however, most are available
at your local home improvement or hardware store.
*House wires may vary in color. Please be sure to verify actual house wires with a certied electrician before
installation.
House
Electrical
Wires*Mirror
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
1. Always disconnect the power supply prior to installing, servicing or removing the LED mirror.
2. Installation work and electrical wiring must be done by a qualied person(s) in accordance with all appli-
cable codes and standards, including re-rated construction.
3. Follow all local building, safety and electrical codes as well as NEC (National Electrical Code) and OSHA
(Occupational Safety and Health Act).
4. Electric service supply must be 120 volts, 60 hertz.
5. This product must properly connect to the grounding conductor of the supply circuit.
6. Do not bend or kink the power wires.
7. When cutting or drilling into the wall or ceiling, do not damage electrical wiring and other hidden utilities.
8. Avoid putting sharp or hard objects against mirror surface. Damage and/or injury may occur if punctured.
9. Turn off product during storms or power surge situations to avoid damage to internal components.

4Homewerks.com
3. Using a 7/32 in. drill bit (not included), drill holes in the
wall where marked and insert drywall anchors (BB).
Hardware Used
BB Drywall anchor x 3
BB
3
4. Place the Z-bar (DD) on the wall and insert the mounting
screws (AA) through the Z-bar (DD) and into the drywall
anchors (BB). Tighten the mounting screws (AA) until the
z-bar (DD) is securely attached to the wall.
Hardware Used
AA Mounting
screw x 3
DD Z-bar x 1
AA DD
BB
4
INSTALLATION INSTRUCTIONS
WARNING: Turn off power at circuit breaker or remove fuse before attempting installation.
1. Determine the midpoint of where the mirror will be installed
and mark with a pencil. Place the Z-bar (DD) on the wall
with the middle hole of the Z-bar (DD) positioned over the
midpoint.
Hardware Used
DD Z-bar x 1
DD DD
AA
1
2. Using a level, make sure the Z-bar (DD) is straight and
mark the other two holes on the Z-bar (DD) located to the
right and left sides. Remove the Z-bar (DD).
Hardware Used
DD Z-bar x 1
DD
2

5
Homewerks.com
INSTALLATION INSTRUCTIONS (Continued)
5. Using a level, mark down from the center of the Z-bar (DD)
22-3/4 in. for horizontal mirror orientation or 28-7/8 for the
vertical mirror orientation. Drill a 7/32 in. hole at this
location and insert a drywall anchor (BB).
Hardware Used
BB Drywall anchor x 1
Vertical mount
DD 22-3/4"
Horizontal mount
DD 28-7/8"
5
6. Drive the locking screw (EE) into the lower drywall
anchor (BB), leaving 1/2 in. exposed.
1/2"
EE
BB
6
7. Connect the white wire from the mirror (A) to the white wire
from the electrical box. Connect the black wire from the
mirror (A) to the black wire from the electrical box. Connect
the green ground wire from the mirror (A) to the ground wire
from the electrical box. Cover and secure each wire connec-
tion with a wire connector (CC).
Hardware Used
CC Wire connector x 3
7
8. Carefully attach the mirror (A) to the z-bar (DD), centering it
and ensuring it is secure. The locking screw (EE) will align
with the keyhole bracket on the back of mirror. Once the
locking screw (EE) is aligned through the keyhole slot,
move the mirror slightly to either side to lock it in place.
Once the mirror (A) is securely in place on the Z-bar
(DD), turn on the power at the circuit breaker or reinsert
the fuse.
Hardware Used
EE Locking
screw x 1
DD Z-bar x 1
A
DD
EE
8