Honeywell Pro-Watch 7000 User manual

Install Guide
Pro-Watch 7000
Input Module
PW7K1IN

Copyright © 2020 Honeywell. All rights reserved.
All product and brand names are the service marks, trademarks, registered trademarks, or registered service marks of their
respective owners. Printed in the United States of America. Honeywell reserves the right to change any information in this
document at any time without prior notice.
Pro-Watch® is a trademark of Honeywell International, Inc.
Ordering Information
Please contact your local Honeywell representative or visit us on the web at www.honeywellintegrated.com for information
about ordering.
Feedback
Honeywell appreciates your comments about this manual. Please visit us on the web at www.honeywellintegrated.com to
post your comments.
Discover | Customer Portal
Self-Service Product Support and Learning Management System
https://honeywelldiscovertraining.com/login/discover/default.asp
YouTube | Honeywell Help and Support
https://www.youtube.com/channel/UCBEL6ouNV_LN5lEpYRujMTg/featured

PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 i
TABLE OF CONTENTS
Notices......................................................................................................................................... iii
Warnings and Cautions........................................................................................................ iii
Disclaimer.................................................................................................................................. iv
Compliance .................................................................................................................................v
CE + WEEE Marking.................................................................................................................v
Unpacking Procedure ........................................................................................................... vi
Shipping Instructions ........................................................................................................... vi
Limited Warranty ................................................................................................................... vii
Confidentiality ........................................................................................................................ vii
Chapter 1 - PW-7000 Input Module.............................................................9
Description........................................................................................................................................ 9
Specification ................................................................................................................................. 10
Set Up............................................................................................................................................... 11
LED Operation.............................................................................................................................. 12
Power................................................................................................................................................ 13
Communications......................................................................................................................... 13
Wiring............................................................................................................................................... 14
Alarm Contact Wiring.......................................................................................................... 15
Control Output Wiring ........................................................................................................ 15
Mounting Options....................................................................................................................... 16
Installing the Module................................................................................................................. 16
Wiring Diagram for Connectors 1 through 12................................................................. 17
Wiring Diagram for Connectors 10 through 12.............................................................. 18

ii PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
This page is intentionally left blank

PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 iii
Notices
Warnings and Cautions
Wiring methods shall be in accordance with the National Electrical Code (ANSI/
NFPA70), Canadian Electrical Code, Part I (CSA C22.1) Safety Standard for Electri-
cal Installations, local codes, and the authorities having jurisdiction.
Warning:
Before installation, TURN OFF the external circuit breaker which supplies power to the system.
Before connecting the device to the power supply, verify that the output voltage is within
specifications of the power supply.
Do not apply power to the system until after the installation has been completed. Personal
injury or death could occur, and the equipment could be damaged beyond repair, if this
precaution is not observed!
Warning: Fire Safety and Liability Notice (Not Evaluated by UL for fire,
life safety, or burglary applications)
Never connect card readers to any critical entry, exit door, barrier, elevator, or gate without
providing an alternative exit in accordance with all fire and life safety codes pertinent to the
installation. These fire and safety codes vary from city to city and you must get approval from
local fire officials whenever using an electronic product to control a door or other barrier. Use of
egress buttons, for example, may be illegal in some cities. In most applications, single action
exit without prior knowledge of what to do is a life safety requirement. Always make certain that
any required approvals are obtained in writing. DO NOT ACCEPT VERBAL APPROVALS,
BECAUSE THEY ARE NOT VALID.
Honeywell never recommends using the PW-7000 or related products for use as a primary
warning or monitoring system. Primary warning or monitoring systems should always meet
local fire and safety code requirements. The installer must also test the system on a regular
basis by instructing the end user in appropriate daily testing procedures. Failure to test a
system regularly could make the installer liable for damages to the end user if a problem
occurs.

iv PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
Note: See the Remote Enclosure Installation manuals PW5K2ENC1/PW5K2ENC2 or
PW5K1ENC3 for installation instructions.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This document and the data in it shall not be duplicated, used, or disclosed to others
for procurement or manufacture, except as authorized by and with the written
permission of, Honeywell, Inc. The information contained in this document or in the
product itself is considered the exclusive property and trade secrets of Honeywell,
Inc. Copyright laws of the United States protect all information in this document or in
the software product itself.
Note: Any use of this product is subject to the terms and acceptance of the Honeywell, Inc.
Software Agreement. Please request a copy from Honeywell, Inc., and review the
agreement carefully.
Disclaimer
Product Liability; Mutual Indemnification
In the event that a Customer receives a claim that a Product or any component
thereof has caused personal injury or damage to property of others, Customer
shall immediately notify Honeywell in writing of all such claims. Honeywell shall
defend or settle such claims and shall indemnify and hold Customer harmless for
Warning:
EARTH ground all enclosures for proper installation.
Warning:
Use suppressors on all door strikes. Use S-4 suppressors for installation. Honeywell
recommends only DC strikes.
Caution:
IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST BE FILED WITH THE
COMMERCIAL CARRIER RESPONSIBLE.
Caution:
Electrostatic discharge can damage CMOS integrated circuits and modules. To prevent
damage, always follow these procedures:
• Use static shield packaging and containers to transport all electronic components,
including completed reader assemblies.
• Handle all ESD sensitive components at an approved static-controlled workstation. These
workstations consist of a desk mat, a floor mat, and an ESD wrist strap. Workstations are
available from various vendors.

PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 v
any costs or damages including reasonable attorneys' fees which Customer may
be required to pay as a result of the defective Product or the negligence of Honey-
well, its agents, or its employees.
Customer shall hold harmless and indemnify Honeywell from and against all
claims, demands, losses, and liability arising out of damage to property or injury to
persons occasioned by or in connection with the acts or omissions of Customer
and its agents and employees, and from and against all claims, demands, losses,
and liability for costs of fees, including reasonable attorneys' fees, in connection
therewith.
Compliance
To obtain applicable EU compliance Declaration of Conformities for this product,
please refer to our website, https://www.security.honeywell.com/All-Categories/
access-control-systems/control-panels-hardware. For any additional information
regarding the compliance of this product to any EU-specific requirements, please
contact:
Honeywell Security & Communications
Honeywell Security - Quality Assurance Dept., Newhouse Industrial Estate Mother-
well
Lanarkshire ML1 5SB Scotland
United Kingdom
Tel: [phone]
Email: [e-mail]
CE + WEEE Marking
Description of the used symbol.
CE -Standard -Logo. This product complies with
the harmonized Regulation of the EU
WEEE symbol.It indicates this product is to be
recycling and not been thrown in the dustbin

vi PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
Unpacking Procedure
The following steps are used to unpack equipment in preparation for installation:
Step 1. Open the container and remove the unit(s) and all packing material.
Retain the container and all packing materials. They may be used again
for reshipment of the equipment, if needed.
Step 2. Inspect the contents for shortage. If items are missing items, contact the
order entry department at 800-323-4576.
Step 3. Visually check contents. If damage is discovered, perform the following:
• If shipping caused damage to the unit, a claim must be
• filed with the commercial carrier.
• If any other defect is apparent, call for a return authorization.
Shipping Instructions
To ship equipment back to Honeywell, Inc.:
Step 1. Contact the customer service department at 800-323-4576 before
returning equipment. When you call please have available:
• A description of the problem or reason you are returning the equipment.
• Your original purchase order number, invoice number and if the unit is still
under warranty.
• A new purchase order number if the unit is not under warranty.
Step 2. From the customer service department, obtain the Return Authorization
Number (RMA).
Step 3. Show the RMA number on all packages shipped. Packages which are not
marked with an RMA number will be refused at the factory and returned
to you COD.
Step 4. Carefully pack the equipment for shipment. Use the original packing
material whenever possible.
Caution:
If any damage to the shipment is noticed before unpacking, a claim must be filed with the
commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to the
contents.

PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 vii
Limited Warranty
All Products sold or licensed by Honeywell include a warranty registration card
which must be completed and returned to Honeywell by or on behalf of the end
user in order for Honeywell to provide warranty service, repair, credit or exchange.
All warranty work shall be handled through Customer which shall notify Honeywell
and apply for a Return Merchandise Authorization (RMA) number prior to returning
any Product for service, repair, credit, or exchange. Honeywell warrants that its
Products shall be free from defects in materials and workmanship for a period of
two years from date of shipment of the Product to Customer. The warranty on Ter-
minals, Printers, Communications Products and Upgrade kits is 90 days from
date of shipment.
Satisfaction of this warranty shall be limited to repair or replacement of Products
which are defective or defective under normal use. Honeywell's warranty shall not
extend to any Product which, upon examination, is determined to be defective as a
result of misuse, improper storage, incorrect installation, operation or mainte-
nance, alteration, modification, accident or unusual deterioration of the Product
due to physical environments in excess of the limits set forth in Product manuals.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THIS PROVISION. THIS
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS,
IMPLIED OR STATUTORY, INCLUDING IMPLIED WARRANTIES OF MERCHANT-
ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. NO REPRESENTATION
OR WARRANTY OF THE DISTRIBUTOR SHALL EXTEND THE LIABILITY OR
RESPONSIBILITY OF THE MANUFACTURER BEYOND THE TERMS OF THIS PRO-
VISION. IN NO EVENT SHALL HONEYWELL BE LIABLE FOR ANY RE-PROCURE-
MENT COSTS, LOSS OF PROFITS, LOSS OF USE, INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES TO ANY PERSON RESULTING FROM THE USE OF HON-
EYWELL'S PRODUCTS.
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and
other materials furnished by Honeywell relating to the design, use and service of
the Products shall remain confidential and shall constitute proprietary rights of
Honeywell and Customer agrees to treat such information as confidential. Cus-
tomer shall acquire no rights in the design of the Products or the related materials
except to use such information solely for the purpose of and only during the time it
sells the Products.
Customer shall not copy the design of any of the Products or use or cause to be
used any Product design or related materials for its own benefit or for the benefit of
any other party. The covenants contained in this section shall remain effective
throughout the term of this Agreement and thereafter unless specifically waived by
Honeywell in writing.

viii PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
This page is intentionally left blank

CHAPTER
1
PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 9
PW-7000 INPUT MODULE
Description
The PW-7000 Input Module provides connections for 16 supervised inputs and
two relay outputs. You can either mount the board in a rack or open and flat. If you
rack-mount the board, only one edge is accessible for wiring; however, a flat mount
increases the amount of available I/O slightly but significantly decreases the num-
ber of boards that can be mounted in one enclosure.
Starting at the bottom of the rack-mount side of the board:
• The first connector provides power to the board.
• The next connector provides communication with the Controller (PW7K1IC or
PW6K1IC).
• Continuing up this edge, the next eight connectors provide supervised input
connections.
• The last connector on the rack-mount edge provides terminals for one relay
output.
When the board is mounted flat, one additional relay output and two dedicated
alarm inputs for cabinet tamper and power fault detection are provided on the
opposite edge of the board.
Both form-C relay outputs are designed to handle dry-circuit signals. All of the
inputs are capable of four-state supervision by using End-of-Line (EOL) resistor
termination except the two dedicated inputs. Communication to the control panel
is accomplished via an RS-485 interface. This board requires 12 VDC input power.
When communication to the controller is lost, this board maintains all previous
output settings at the time communication was lost.

10 PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
Specification
The Input Board is for use in low voltage, class 2 circuits only.
Primary power:
12VDC + 10%, 250mA maximum
Relay contacts:
Relays 0 and 1 outputs, Form-C, 2A @ 30VDC, resistive
Inputs:
• 16 supervised, End of Line resistors 1k ohm ± 1% tolerance
• 2 unsupervised dedicated inputs
Wire requirements:
Mechanical:
Environment:
Power 1 twisted pair, 18AWG
RS-485 24AWG, 4,000 feet (1,200 m) max., 2-twisted pair with shield
(120 ohms, 23pf) (Belden 9842 or equiv.)
Alarm inputs 1 twisted pair per input, 30 ohms max.
Outputs As required for the load
Dimension 5.5" (140mm) W x 9" (229mm) L x 1" (25mm) H
Weight 12 oz. (340g) nominal
Temperature 0°C to +49°C, operating, -55°C to +85°C, storage
Humidity 0% to 85% RHNC

PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 11
Set Up
Table 1: PW-7000 Input Module Jumper Settings
Table 2: PW-7000 Input Module DIP Switch Settings
Jumper Setting Default Selected
J1 OFF X Port 1 RS-485 EOL terminator is not active
ON Port 1 RS-485 EOL terminator is active
S8 S7 S6 S5 S4 S3 S2 S1 Selection
OFF OFF OFF OFF OFF ADDRESS 0
OFF OFF OFF OFF ON ADDRESS 1*
OFF OFF OFF ON OFF ADDRESS 2
OFF OFF OFF ON ON ADDRESS 3
OFF OFF ON OFF OFF ADDRESS 4
OFF OFF ON OFF ON ADDRESS 5
OFF OFF ON ON OFF ADDRESS 6
OFF OFF ON ON ON ADDRESS 7
OFF ON OFF OFF OFF ADDRESS 8
OFF ON OFF OFF ON ADDRESS 9
OFF ON OFF ON OFF ADDRESS 10
OFF ON OFF ON ON ADDRESS 11
OFF ON ON OFF OFF ADDRESS 12
OFF ON ON OFF ON ADDRESS 13
OFF ON ON ON OFF ADDRESS 14
OFF ON ON ON ON ADDRESS 15
ON OFF OFF OFF OFF ADDRESS 16
ON OFF OFF OFF ON ADDRESS 17
ON OFF OFF ON OFF ADDRESS 18
ON OFF OFF ON ON ADDRESS 19
ON OFF ON OFF OFF ADDRESS 20
ON OFF ON OFF ON ADDRESS 21
ON OFF ON ON OFF ADDRESS 22
ON OFF ON ON ON ADDRESS 23
ON ON OFF OFF OFF ADDRESS 24
ON ON OFF OFF ON ADDRESS 25
ON ON OFF ON OFF ADDRESS 26
ON ON OFF ON ON ADDRESS 27
ON ON ON OFF OFF ADDRESS 28
ON ON ON OFF ON ADDRESS 29
ON ON ON ON OFF ADDRESS 30
ON ON ON ON ON ADDRESS 31
OFF OFF Reserved

12 PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
* = Default
LED Operation
The Input Board uses two onboard LEDs (D1 and D2) to provide status information
during the power-up sequence as well as during normal operation.
Table 3: PW-7000 Input Module Onboard LED Settings
In addition to the status LEDs, there are two additional relay status LEDs and 16
input status LEDs on board. The input LEDs flash when there is an alarm associ-
ated with the input. When any relay or input is energized or ON, its corresponding
status LED becomes ON also. The LED remains ON for as long as the relay is ener-
gized.
The assignment for each relay status LED is shown in the following table.
OFF ON 9,600 BPS
ON OFF 19,200 BPS
ON ON 38,400 BPS*
OFF Not Used*
S8 S7 S6 S5 S4 S3 S2 S1 Selection
Mode LED D1 LED D2 Description
Power-up sequence ON OFF Start power-up, hardware setup.
OFF ON Testing RAM.
ON ON Testing ROM and completing initialization.
FLASH ON LED D1 flashes four times after power-up is completed.
Normal Operation FLASH This is the processor heartbeat LED. It flashes once every second. A short ON
time (~20% duty cycle) indicates the board is offline or has lost serial
communication with the Controller board. A long ON time (~80% duty cycle)
indicates the board is Online and communicating with the Controller board.
FLASH Flash when there is activity on its Serial Port.

PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 13
Table 4: Additional PW7000 Input Module LEDs
Power
The Input Board accepts 12VDC with an operating range of 10 to 14VDC and con-
sumes 250mA of current. Locate power source as close to this board as possible.
Connect power with minimum of 18AWG wire.
Note: POLARITY for 12VDC power is important. Make sure the +12 VDC is connected to the
terminal labeled +12V and the return is connected to the terminal labeled GND.
Communications
The Input Board communicates to the host controller through an RS-485 inter-
face.The interface allows for multi-drop communication of up to 4,000 feet (1,200
m) total per port. Use two twisted pair (minimum 24AWG) with shield for communi-
cation (Belden 9842 or equiv.). The default speed of this port is 38.4Kbps but it can
be downgraded to 19.2Kbps or 9.6Kbps if the line conditions or receiving equip-
ment require it (see Table 1: PW-7000 Input Module Jumper Settings (page 11) for
jumper settings and Table 2: PW-7000 Input Module DIP Switch Settings (page 11)
for DIP switch settings).
LED number Description
D3 Input 0 status
D4 Input 1 status
D5 Input 2 status
D6 Input 3 status
D7 Input 4 status
D8 Input 5 status
D9 Input 6 status
D10 Input 7 status
D11 Input 8 status
D12 Input 9 status
D13 Input 10 status
D14 Input 11 status
D15 Input 12 status
D16 Input 13 status
D17 Input 14 status
D18 Input 15 status
D19 Tamper status
D20 Power status
D21 Relay 0 status
D22 Relay 1 status

14 PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
For wiring to an RS-485 port:
Step 1. TR+ is the plus side of the transmit and receive differential signal.
Step 2. TR- is the negative side of the transmit and receive differential signal.
Step 3. GND is the signal ground. The wiring for this signal is required and NOT
optional. This signal must NOT be connected to chassis GND.
Step 4. Use 24 AWG low capacitance, two twisted-pair, shielded cable (Belden
9842 or equiv.).
Note: For RS-485 Communication Connections, twist the blue pair together and use as the
common; use the orange pair as your data pair, observing polarity. Connect the
external drain shield to the appropriate earth ground on one end.
Step 5. When daisy-chaining RS-485 ports together, connect the TR+ wires from
the upstream and downstream boards to the TR+ terminal. Likewise,
connect the TR- wires from the upstream and downstream boards to the
TR- terminal.
By factory default J1 is set open. If this board is the last board on the RS-485 bus,
install jumper J1 across both pins (closed). Closing J1 provides the bus termina-
tion required.
Wiring
This section presents information on alarm contact wiring and control output wir-
ing.

PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 15
Alarm Contact Wiring
Inputs 0 to 15 may be configured to use normally open or normally closed contacts
and non-supervised or supervised (with standard ±1 tolerance 1K ohm). All 16
inputs can be configured to monitor general-purpose alarm sensors or can be
used as control inputs.
Additional inputs TMP and PFL are typically used for monitoring cabinet tamper
and power failure respectively. These two inputs are not supervised and are not
accessible when the board is rack-mounted. These inputs are used when this board
is mounted remotely and cannot take advantage of the tamper and power fail
detect inputs on the controller board. If these inputs are not used, install a short
piece of wire at the input to indicate safe condition.
Input configuration including sensitivity and hold time is set via host software.
Control Output Wiring
Two form-C relay contacts are provided for controlling other devices. Each may be
assigned to a general-purpose output. They are configurable as standard (energize
to activate) or fail-safe (de-energize to activate) by the host software.
The energized or ON time of each relay can be configured using pulse control for
single or repeating pulses via host software. The energized or ON time of a single
pulse can be extended up to 24 hours. For repeating pulses, the on/off time can be
defined in 0.1 second increments and be repeated up to 255 times.
Relays 0 and 1 are rated for dry contact signal or load switching. While they are
sized to handle typical loads, load switching can cause abnormal contact wear and
premature contact failure. Switching of inductive loads (e.g., strikes) also causes
EMI (electromagnetic interference) which may interfere with normal operation of
other equipment. To minimize premature contact failure and to increase system
reliability, a contact protection circuit is highly recommended. The following circuit
is suggested. Locate the protection circuit as close to the load as possible (within
12 inches [30cm]); the effectiveness of the circuit decreases as the distance from
the load increases.

16 PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
Relay 1 is a general-purpose relay output and is not available when the board is
rack-mounted.
Use sufficiently large gauge of wires for the load current to avoid voltage loss.
Mounting Options
This board can be mounted on-edge in the rack-mount enclosure provided by
Honeywell or it can be mounted flat against any surface using standoffs under the
mounting holes provided in each of the four corners of this board.
When this board is rack-mounted, the connectors for one general-purpose output,
two general-purpose outputs, and two dedicated inputs are not accessible and
should not be used.
The most common reason for mounting a board flat is that it is being installed
remotely to be located near the alarms being monitored. In this case, mount it in its
own enclosure. Use the two dedicated inputs to monitor cabinet tamper and power
fault. The additional general-purpose output provided allows for control of a local
horn or other equipment.
Installing the Module
Step 1. Set Jumpers and DIP switches.
Step 2. Mount this board in the appropriate enclosure. If this board is being
mounted in a rack, the component side of the board is to your right as you
face the rack.
Step 3. Connect the communications and power supply to the circuit boards with
the Power Supply Harness.
Step 4. Connect wiring to alarm input sensors or install jumper wire as
appropriate.
Step 5. Connect relay output wiring as appropriate.
Step 6. Connect communications wiring to the Intelligent Controller.
Step 7. Recheck wiring for correct connections and continuity.
Step 8. When all boards have been installed, connect the power supply cord for
proper connections and power.
Step 9. Set up the panel controls using the host software.
Warning: DO NOT CONNECT THE POWER SUPPLY TO THE AC SOCKET
UNTIL ALL WIRING HAS BEEN INSTALLED AND RECHECKED.

PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1 17
Wiring Diagram for Connectors 1 through 12
Figure 1: PW-7000 Input Module Wiring: Connectors 1-12
Note: See LED Operation for descriptions of LEDs D1-D22.
DIP SWITCHES
ON
OFF
87654321
INPUT BOARD
Short
together*
Power
RS-485
NO
C
CardRack PWR
and
Com Harness*
(Rack Mount
Only)
EOL
EOL
Alarm
Input
Sensor
Input
RS-485 TR+
RS-485 TR-
RS-485 GND
+ 12V
GND
IN14
IN14 Common
IN15
IN15 Common
IN12
IN12 Common
IN13
IN13 Common
IN10
IN10 Common
IN11
IN11 Common
IN8
IN8 Common
IN9
IN9 Common
IN6
IN6 Common
IN7
IN7 Common
IN4
IN4 Common
IN5
IN5 Common
IN2
IN2 Common
IN3
IN3 Common
IN0
IN0 Common
IN1
IN1 Common
Relay 0 NO
Relay 0 C
Relay 0 NC
Self-Powered
Audio / Visual
Alarm Indicator
K 1
K 2
J 1 - RS-485
Termination
J 2
{
1
2
3
1
2
3
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
5
1
2
3
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22

18 PW-7000 Input Module (PW7K1IN) Installation Guide, Document 800-25674V1
Wiring Diagram for Connectors 10 through 12
Figure 2: PW-7000 Input Module Wiring: Connectors 10-12
Note: For RS-485 Communication Connections, twist the blue pair together and use as the
common; use the orange pair as your data pair, observing polarity. Connect the
external drain shield to the appropriate earth ground on one end.
DIP SWITCHES
ON
OFF
87654321
INPUT BOARD
Power
RS-485
RS-485
Com Bus Cable
From Di. Panel*
(Remote Mount
Only)
N/C - Low Battery
C - Low Battery
C - No Charging
N/C - No Charging
+12VDC Power
Supply
DC Output
+
_
Input 1
Input 1
Common
Switch
Common
Power Fail
PWR +
PWR -
NC
Chassis GND at Other Panel
Connect to chasis
GND at one side
ONLY !
* REMOTE MOUNT CONFIGURATION
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
RS-485 TR+
RS-4845 TR-
RS-485 GND
+ 12V
GND
IN14
IN14 Common
IN15
IN15 Common
IN12
IN12 Common
IN13
IN13 Common
IN10
IN10 Common
IN11
IN11 Common
IN8
IN8 Common
IN9
IN9 Common
IN6
IN6 Common
IN7
IN7 Common
IN4
IN4 Common
IN5
IN5 Common
IN2
IN2 Common
IN3
IN3 Common
IN0
IN0 Common
IN1
IN1 Common
Relay 0 NO
Relay 0 C
Relay 0 NC
K 1
K 2
J 1 - RS-485
Termination
J 2
{
Relay 1 NC
Relay 1 C
Relay 1 NO
Tamper
Ground
Power Fail
Temper Switch
(In CLOSED position
when Cabinet Door is
closed)
The connectors on this side
of the board are not
accessible when it is rack
mounted.
1
2
3
1
2
3
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
5
1
2
3