Hoover HSPN 1L390PW User manual

EN

!
2
Thank you for choosing a Hoover dish
washer. We are confident it will assist you
loyally in washing your daily dishes in full
safety.
Carefully read this manual for correct and
safe appliance use and for helpful tips on
efficient maintenance.
Only use the dish washer
after
carefully reading these instructions. We
recommend you always keep this manual
to hand and in good condition for any
future owner.
Please check that the appliance is
delivered with this instruction manual, the
warranty certificate, the service centre
address and the energy efficiency label.
Each product is identified by a unique 16-
digit code, also called the “serial number”,
printed on the warranty certificate or on
the serial plate found inside the door, on
the upper right hand side. This code is a
sort of product-specific ID card that you
will need to use to register the product or
if you need to contact the Technical
Assistance Centre.
Fig. A
15
4
32
1. GENERAL SAFETY RULES
2. WATER CONNECTION
3. LOADING THE SALT
4. ADJUSTING THE UPPER BASKET
(ONLY ON SOME MODELS)
5. LOADING DISHES
6. INFORMATION FOR TEST
LABORATORIES
7. LOADING THE DETERGENT
8. TYPES OF DETERGENT
9. LOADING THE RINSE AID
10. CLEANING THE FILTERS
11. PRACTICAL HINTS
12. CLEANING AND MAINTENANCE
13. DESCRIPTION OF THE CONTROL PANEL
14. TECHNICAL DATA
15. PROGRAMME SELECTION AND SPECIAL
FEATURES
16. REMOTE CONTROL (Wi-Fi)
17. PROGRAMME LEGEND
18. WATER SOFTENER UNIT
19. TROUBLESHOOTING AND WARRANTY
20. ENVIRONMENTAL CONDITIONS
A. WIRELESS PARAMETERS (PAG.36)
Contents

!
EN
3
1. GENERAL SAFETY
RULES
! This appliance is intended to
be used in household and
similar applications such as:
−Staff kitchen areas in
shops, offices and other
working environments;
−Farm houses;
−By clients in hotels, motels
and other residential type
environments;
−Bed and breakfast type
environments.
A different use of this appliance
from household environment
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded
even in the above applications. If
the appliance is used in a manner
inconsistent with this it may reduce
the life of the appliance and may
void the manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer to
the fullest extent permitted by law.
!This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved. Children shall
not play with the appliance.
Cleaning and user maintenance
shall not be made by children
without supervision.
!Children should be supervised
to ensure that they do not play
with the appliance.
!Children of aged 3 and under
should be kept away unless
continuously supervised.
!If the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard. We
recommend using an original
component, which can be
requested from the Technical
Assistance Centre.
! Only use the hose-sets
supplied with the appliance for
the water supply connection
(do not reuse old hose-sets).
! Water pressure must be
between 0.05 MPa and 0.8
MPa.

!
4
! Make sure carpets or rugs do
not obstruct the base or any of
the ventilation openings.
!After installation, the appliance
must be positioned so that the
plug is accessible.
! Do not leave the door open in
a horizontal position, in order
to avoid potential dangers (e.g.
tripping).
!For further information on the
product or to consult the technical
data sheet, please refer to the
manufacturer's website.
! The technical details (supply
voltage and power input) are
indicated on the product rating
plate.
! Make sure that the electrical
system is earthed and complies
with all applicable laws, and
that the socket is compatible
with the plug of the appliance.
The manufacturer declines all
responsibility for any damage
to people or property due to
non-earthing of the machine.
!Ensure that the dishwasher
does not crush power cables.
!In general it is not advisable to
use adaptors, multiple plugs
and/or extension cables.
!Before cleaning or maintaining
the dishwasher, unplug the
appliance and turn off the
water supply.
!Do not pull on the power cord
or appliance to unplug the
machine.
!Do not leave the appliance
exposed to the elements (rain,
sun, etc.).
!Leaning or sitting on the open
door of the dishwasher could
cause it to tip over.
! The dishwasher is designed for
normal kitchen utensils. Objects
that have been contamined by
petrol, paint, traces of steel or
iron, corrosive chemicals, acids
or alkalis must not be washed in
the dishwasher.
WARNING:
Knives and other utensils
with sharp points must be
loaded in the basket with
their points down or placed
in a horizontal position.
Electrical connections and
safety instructions

!
EN
5
! If there is a water softening
device installed in the home
there is no need to add salt to
the water softener fitted in the
dishwasher.
! If the appliance breaks down or
stops working properly, switch it
off, turn off the water supply and
do not tamper with it. Repair work
should only be carried out by an
approved service agent and only
genuine spare parts should be
fitted. Any failure to follow the
above advice may have serious
consequences for the safety of
the appliance.
!If it you need to move the
machine after removing the
packaging, do not try to lift it by
the bottom of the door. Open
the door slightly and lift the
machine by holding on the top.
By marking this product,
we confirm, under our own
responsibility, full compliance
of this product with all
relevant safety, health and
environmental requirements
under European legislation.
! Remove all elements of the
packaging.
!Do not install or use the
dishwasher if it is damaged.
! Follow the instructions supplied
with the product.
Installation
WARNING:
Keep packaging materials
away from children.

!
6
2. WATER CONNECTION
!The inlet and drain hoses can be directed
to left or right.
! Water pressure must be between 0,08
MPa and 0,8 MPa.
! The inlet hose must be connected to a tap
so that the water supply can be cut off
when the machine is not in use (fig. 1 B).
!The dishwasher is fitted with 3/4" threaded
connector (fig. 2).
!Connect inlet hose "A" to water tap "B"
with a 3/4" attachment making sure that it
has been properly tightened.
!If it is necessary, the inlet pipe can be
lengthened up to 2,5 m. The extension
pipe is available from the After Sales
Service Centre.
!If the dishwasher is connected to new pipes
or to pipes which have not been inuse for a
long time run water through for a few
minutes before connecting the inlet hose. In
this way no deposits of sand or rust will
clog up the water inflow filter.
1
B
2
B
A
The appliance must be connected to
the water mains using new hose-sets.
The old hose-sets should not be
reused.
The dishwasher can be connected to
either cold or hot water, as long as it
is no hotter than 60°C.

!
EN
7
SOME MODELS may include one or more
of the following features:
!WATERBLOCK (fig. 3)
The waterblock system has been designed to
improve the safety of your appliance. The
system prevents flooding which might be
caused by a machine malfunction or as a
result of a fracture on the rubber pipes
and in particular on the water supply pipe.
How it works
A sump located on the base of the appliance
collects any possible water leakage and
operates a sensor which activates a valve
placed under the water tap and blocks any
water, even with the tap fully opened.
If box "A" containing the electrical parts is
damaged, remove the plug from the socket
immediately. To ensure perfect operation of
the safety system, the hose with box "A"
should be connected to the tap as shown in
the figure. The water supply hose should
not be cut, as it contains live parts. If the
hose is not long enough for correct
connection, it must be replaced with a longer
one. The hose can be obtained from the
Technical Assistance Centre.
3A
!AQUASTOP (fig. 4):
A device located on the supply tube that
stops water flow if the tube deteriorates;
in this case, a red mark will appear in the
window "A" and the tube must be
replaced. To unscrew the nut, press the
one-way lock device "B".
B
A
4
! AQUAPROTECT - SUPPLY TUBE WITH
GUARD (fig. 5):
Should water leak from the primary internal
tube "A", the transparent containment
sheath "B" will contain water to permit
the washing cycle to complete. At the
end of the cycle, contact the Customer
Service Centre to replace the supply
tube.
B
A
5
Hydraulic safety devices
All the dishwashers are equipped with
an overflow safety device which, if
water exceeds normal levels due to
malfunctions, automatically blocks
water flow and/or drains excess
quantities.

!
8
!The outlet hose should disharge into a
standpipe, making sure that there are no
kinks (fig. 6).
!The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
!It is advisable to fit an anti-odour air trap
(fig. 6X). If necessary the outlet hose can
be extended up to 2,5 m, provided that it
is kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the After Sales Service
Centre.
!The hose can be hooked over the side of
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 6Y).
!When installing the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest
possible position under the worktop
(fig. 6Z).
!Check that there are no kinks in the inlet
and outlet hoses.
6
Z
Y
X
Connecting the outlet hose

!
EN
9
3. LOADING THE SALT
(Fig. A "1")
!The appearance of white stains on dishes
is generally a warning sign that the salt
container needs filling.
!On the bottom of the machine there is a
container for the salt for regenerating the
softener.
!It is important to use only a salt that is
specifically designed for dishwasher.
Other types of salt contain small
quantities of insoluble particles which
over a long period of time may affect and
deteriorate the softener performance.
!To add salt, unscrew the cap of the
container on the bottom and then refill the
container.
!During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
!After loading the salt, it is recommended
running a complete washing cycle, or
COLD RINSE programme.
!The salt dispenser has a capacity of
between 1.5 and 1.8 kg and, for efficient
use of the appliance, it should be refilled
from time to time .
After loading the salt, YOU MUST run
a complete washing cycle, or the
PRE-WASH/COLD RINSE/REFRESH
programme.
(Only for first start up) When the
appliance is used for the first time,
after completely filling the salt
container, it is necessary to add water
until the container overflows.

!
10
4. ADJUSTING THE UPPER
BASKET (ONLY ON SOME
MODELS)
! If 29 cm to 32.5 cm plates are regularly
used, load them onto the lower basket
after the upper basket has been placed in
its upper position, as detailed below
(according to the model):
Type "A":
1. Turn front blocks "A" outwards;
2. Remove the basket and remount it in
the upper position;
3. Replace blocks "A" in the original
position.
Dishes that are greater than 20 cm in
diameter can no longer be loaded onto the
upper basket, and the mobile supports
cannot be used when the basket is in the
upper position.
Type "A"
A
A
Type "B": (ONLY MODELS WITH EASY CLICK):
1. Remove the upper basket;
2. Hold the basket on both sides and lift it
upwards (fig. 1).
Dishes that are greater than 20 cm* in
diameter can no longer be loaded onto the
upper basket, and the mobile supports
cannot be used when the basket is in the
upper position.
*In models fitted with a third basket, dishes
measuring more than 14 cm in diameter
can no longer be loaded onto the upper basket.
ADJUSTING THE BASKET TO THE
LOWER POSITION:
1. Hold the basket on both sides and lift it
gently upwards (fig. 1);
2. Then slowly release into the correct
position (fig. 2).
N.B.: NEVER LIFT OR LOWER THE
BASKET FROM ONE SIDE ONLY (fig. 3).
WARNING:
We recommend adjusting the basket before
loading the dishes.
Type "B"
1
3
a
b
a
b
2

!
EN
11
5. LOADING DISHES
!The upper basket is provided with mobile
racks hooked to the sides of the basket,
which can be regulated into 4 positions.
!In the lowered position (A-A1) the racks
may be used for such items as: tea and
coffee cups, kitchen knives and ladles.
Also glasses with stems may be safely
hung on the ends of the racks.
! In the upright position (B-B1) the racks
allow you to load dinner plates and soup
plates. Plates should be loaded vertically
with the underside of the plate towards
the back of the dishwasher with a space
between each plate to allow water to pass
freely.
!It is advisable to load large plates
(approx. 26 or more cm) slightly tilted
towards the rear to facilitate introduction
of the basket into the machine.
!Salad bowls and plastic bowls may also
be loaded on the upper basket. It is
advisable to block these in place so that
the jets of water do not make them
overturn.
! The upper basket has been designed to
offer maximum flexibility in use and can
be loaded with up to 24 plates on two
rows, up to 30 glasses on five rows or a
mixed load.
example of loading see fig. 1, 2 e 3.
Upper basket (fig. 1)
Upper basket (fig. 2)
Upper basket (fig. 3)
!Saucepans, oven dishes, tureens, salad
bowls, lids, serving dishes, dinner plates,
soup plates and ladles can be loaded on
the lower basket.
Using the upper basket
Using the lower basket

!
12
!Place the cutlery in the plastic cutlery
holder with the handles pointing upwards.
!Place the cutlery holder on the lower
basket (fig. 4 and 5), making sure that
the cutlery does not get in the way of the
rotating arms.
Please load the dishwasher sensibly to
ensure the best wash results.
example of loading see. fig. 4 e 5
Lower basket (fig. 4)
Lower basket (fig. 5)
Cutlery basket (fig. 6)
The cutlery basket is made with two
detachable parts which will enable various
loading options. The two parts can be
detached by sliding the left section away
from the right section. The top of cutlery
basket can be removed, for enable various
loading options.
6. INFORMATION FOR
TEST LABORATORIES
Please ask information required for
comparison testing and measuring noise
levels, according to EN normative, to the
following address:
testinfo-[email protected]
In the request, please specify model name
and number of the dishwasher (see rating
plate).
The lower basket has a safety-stop
device, for its safe extraction, also
especially useful with a full load. For
loading salt, cleaning filter and for
ordinary maintenance, the complete
extraction of the basket is necessary.

!
EN
13
7. LOADING THE
DETERGENT
(Fig. A "2")
Unsuitable detergents (like those for
washing up by hand) do not contain the
proper ingredients for use in a dishwasher,
and stop the dishwasher from working
correctly.
The detergent container is inside the door
(fig. A "2"). If the lid of the container is
closed, press the button (A) to open. At the
end of every wash cycle the lid is always
open and ready for the next time the
dishwasher is used.
The amount of detergent to be used varies
according to how dirty the dishes are and
on the type of dishes to be washed. We
advise using 20:30 g of detergent in the
wash section of detergent compartment (B).
After pouring the detergent into the
container, close the lid, firstly pushing (1)
and then pressing on it (2) until you hear
the click.
Since not all detergents are the same the
instructions on the boxes of detergent can
vary. We should just like to remind users
that too little detergent does not clean the
dishes properly whilst too much detergent
will not produce better results and is also a
waste.
The detergent
It is essential to use a detergent that is
specifically designed for dishwashers
either in powder, liquid,gel or tablet form.
Filling the detergent container
WARNING
When loading the lower basket, please
ensure that the plates or others do not
obstruct the detergent dispenser.
Do not use an excessive amount of
detergent and help limit damage to the
environment at the same time.

!
14
8. TYPES OF DETERGENT
Detergent tablets of different manufacturers
dissolve at different speeds, for this reason,
during short programmes, some detergent
tablets may be not fully effective, because
they are not completely dissolved. If these
products are used, is recommended to
choose longer programmes to guarantee
the complete use of the detergent.
The concentrated detergents, with reduced
alkalinity and with natural enzymes, in
conjunction with 50°C wash programmes,
have a smaller impact on the environment
and they protect the dishes and the
dishwasher. The 50°C wash programmes
purposely exploit the dirt-dissolving
properties of the enzymes, allowing
therefore, with the use of the concentrated
detergents, to achieve the same results of
the 65°C programmes but at a lower
temperature.
The detergents that also contain the rinse
aid must be placed in the wash section of
the detergent container. The rinse aid
container must be empty (if it is not empty,
set the rinse aid regulator to lowest position
before using combined detergents).
If you are planning to use "TABS" (“3 in
1 “/ “4 in 1”/ “5 in 1”, etc.) combined
detergents i.e. those with built in salt and/or
rinse agent, we would advise the following:
! read carefully and follow the manufacturer’s
instructions given on the packaging;
!the effectiveness of detergents
containingthe built in water softener/salt
depends on the hardness of your water
supply. Check that the hardness of your
water supply is within the effective range
given on the detergent packaging.
If when using this type of product, you
don't get satisfactory washing results,
please contact the detergent manufacturer.
In certain circumstances use of combined
detergents can cause:
!limescale deposits on dishes or in the
dishwasher;
!a reduction in washing and drying
performance.
Please note that using the "TABS"
combined detergents, the rinse aid and
salt indicator lights (only used on
selected models) are superfluous, so
you must ignore the lights.
If washing and/or drying problems occur,
we recommend you return to use traditional
separate products (salt, detergent and rinse
agent). This will ensure that the water
softener in the dishwasher operates
correctly.
In this case, we recommends that you:
!refill both the salt and rinse aid container;
!run one normal washing cycle without a
load.
Please note that on return to the use of
conventional salt, a number of cycles will be
required before the system becomes fully
efficient again.
Detergent tablets
To get satisfactory washing results,
the tablets MUST be placed in the
wash section of the detergent
container and NOT directly in the tub.
Concentrated detergents
Combined detergents
"TABS" combined detergents
Any problems which arise as a direct
result of the use of these products are not
covered by our warranty.

!
EN
15
9. LOADING THE RINSE AID
(Fig. A "3")
The rinse aid, which is automatically
released during the last rinsing cycle, helps
the dishes to dry quickly and prevents spots
and stains forming.
The rinse aid container can be found to the
left of the detergent container (fig. A "3").
To open the lid, push the reference mark
and, in the same time, pull the tab of
opening. It is always advisable to use rinse
aid that is specifically designed for
dishwasher. Check the rinse aid level
through the indicator eye (C) which is
located on the dispenser.
FULL
EMPTY
dark
light
The regulator (D) is placed under the lid
and can be turned using a coin. The
recommended position is 4.
The limestone content of the water
considerably affects the formation of
limescale and the drying performance.
It is therefore important to regulate the
quantity of rinse aid to achieve good
washing results.
If, after the wash, streaks occur on the
dishes, decrease the amount by one
position. If whitish spots occur, increase the
amount by one position.
The rinse aid
Filling the rinse aid container.
Regulating the rinse aid from
1 to 6

!
16
10. CLEANING THE FILTERS
(Fig. A "4")
The filter system consists of:
A.A central container that traps the larger
particles;
B.A micro filter, located beneath the
gauze, that traps the tiniest particles
ensuring a perfect rinse;
C.A flat gauze that continuously filters the
wash water.
!To achieve excellent results every time,
the filters should be checked and cleaned
after each wash.
!To remove the filter unit, simply turn the
handle anticlockwise (fig. 1).
!For ease of cleaning, the central
container is removable (fig. 2).
!Remove the gauze filter (fig.3) and wash
the whole unit under a jet of water. If
necessary a small brush can be used.
!With the Self-cleaning Micro filter,
maintenance is reduced and the filter unit
need only be checked every two weeks.
Nevertheless, after each wash it is advisable
to check that the central container and the
gauze filter are not clogged.
WARNING
After cleaning the filters, make sure that
they are correctly reassembled and
that the gauze filter is properly
positioned at the bottom of the
dishwasher. Make sure that the filter
is screwed back, clockwise, into the
gauze, as poor seating of the filter unit
could have an adverse effect on the
efficiency of the appliance.
Never use the dishwasher without the
filters.

!
EN
17
11. PRACTICAL HINTS
!Before placing the dishes in the
dishwasher, remove any remaining food
(bones, shells, pieces of meat or
vegetables, coffee grounds, skin of fruit,
cigarette ash, thooth picks etc. to avoid
blocking the filters, water outlet and
washing arm nozzles.
!Try not to rinse the dishes before loading
them into the dishwasher.
!If saucepans and oven dishes are
encrusted with the remains of burnt or
roast food, it is advisable to leave them to
soak before washing.
!Place the dishes face downwards.
!Try to place the dishes in such a way that
they are not touching one another. If they
are loaded properly you will get better
results.
!After loading the dishes check that the
washing arms can rotate freely.
!Pans and other dishes that have
particularly stubborn food particles or
remnants of burnt food should be left to
soak in water with dishwasher detergent.
!To wash silver properly:
a) rinse the silver immediately after use,
especially if it has been used for
mayonnaise, eggs, fish etc.;
b) do not sprinkle detergent onto it;
c) keep it separate from other metals.
!If you want the dishwasher to give a
complete wash, place the dishes in the
dishwasher at the end of each meal and if
necessary turn on the COLD RINSE cycle
to soften the food remains and remove
bigger particles of food from the new load
of dishes. When the dishwasher is full
start the complete wash cycle
programme.
!If the dishes are not very dirty or if the
baskets are not very full select an
ECONOMY programme, following the
instructions in the program list.
!It should be remembered that not all
dishes are suitable for washing in a
dishwasher. We advise against using the
dishwasher to wash items in
thermoplastic, cutlery with wooden or
plastic handles, saucepans with wooden
handles, items in aluminum, crystal
leaded glass unless otherwise stated.
!Certain decorations may fade. It is
therefore a good idea before loading the
whole batch to wash just one of the items
first so as to be sure that others like it will
not fade.
!It is a good idea not to put silver cutlery
with non-stainless steel handles into the
dishwasher as there could be a chemical
reaction between them.
!In order to avoid any dripping from the top
rack, remove the lower rack first.
!If the dishes are to be left in the machine
for some time, leave the door ajar, to let
some air circulate and to improve the
drying performance.
How to get really good wash
results.
How to make savings.
What not to wash.
When buying new crockery or cutlery
always make sure that they are
suitable for washing in a dishwasher.
Useful hints

!
18
12. CLEANING AND
MAINTENANCE
(Fig. A “5”)
!To clean the dishwasher outside, do not
use solvents (degreasing action) neither
abrasives, but only a cloth soaked with
water.
!The dishwasher does not require special
maintenance, because the tank is self-
cleaning.
!Regularly wipe the door gasket with a
damp cloth to remove any food remains
or rinse aid.
!Dishwasher cleaning is recommended, in
order to remove limestone deposits or
dirt. We suggest you run a washing cycle
periodically with specialist dishwasher
cleaning products. For all cleaning
operations the dishwasher must be
empty.
!If, in spite of the routine cleaning of the
filters, you notice that the dishes or pans
are not properly washed or rinsed, check
that all the spray heads on the rotor arms
(fig. A “5”) are clear.
If they are blocked, clean them in the
following way:
1) to remove the upper rotor arm, turn it
until it lines up with the stop marked by
the arrow (fig. 1b). Push it upwards
(fig. 1) and, keeping it pushed in,
unscrew it in a clockwise direction (to
reassemble it repeat the same
operation, but turn it anticlockwise).
The lower rotor arm can be removed
simply by pulling it upwards (fig. 2);
2) wash the rotor arms under a jet of water
to clear any blockage in the spray
heads.
3) when you have finished, refit the rotor
arms in the same position,
remembering to re-align the arrow and
screw into position.
!Both the door lining and the tank lining
are in stainless steel; however, should
spots caused by oxidation occur, this is
probably due to a high level of iron salts
presents in the water.
!The spots can be removed with a mild
abrasive agent; never use chlorine based
materials, steel wool, etc.
11b
2
After every wash it is essential to turn off
water supply and to switch off the machine
by pressing the On/Off button to the off
position.
Do not use tools that can deform the
spray heads.
WHEN CYCLE IS FINISHED.

!
EN
19
If the machine is not going to be used for
some time, it is advisable to follow these
rules:
1. do an empty wash with detergent in
order to clean the machine of any
deposits;
2. pull out the electric plug;
3. turn off the water tap;
4. fill the rinse aid container;
5. Ieave the door ajar;
6. keep the inside of the machine clean;
7. If the machine is left in places where the
temperature is below 0°C any water left
inside the pipes may freeze. Wait until
the temperature rises above zero and
then wait for about 24 hours before.

!
20
13. DESCRIPTION OF THE
CONTROL PANEL
G "RINSE AID EMPTY" light
H
"PROGRAMME STATUS" lights/"DELAY START" time lights
I D+E CHILD LOCK
L "OPTION SELECTION" light
M "PROGRAMME SELECTION" light
N "Addish" light
A ON/OFF Button
B "Start/Reset" button (start/cancel programme)
C "PROGRAMME SELECTION" button/ENROLMENT Wi-Fi
D "Express" option button
E "START DELAY" button
F "Reset" button for "SALT EMPTY" light
14. TECHNICAL DATA
SIZE
BUILT-IN
FULL-INTEGRATED
59,8x81,8 ÷ 89,8x55
117
TECHNICAL DATA (See rating plate)
16
9 people
Min. 0,08 – Max. 0,8
See rating plate
HALF-INTEGRATED
59,8x81,8 ÷ 89,8x57
117
15
9 people
FREE-STANDING
WITHOUT
WORKTOP
59,8x82x58
117
13
8 people
WITH
WORKTOP
60x85x60.9
120
Place settings (EN 50242)
Capacity with pans and dishes
Water supply pressure (MPa)
Fuse / Power input / Supply voltage
DATA
Width x Height x Depth (cm)
Depth with door open (cm)