Hoover HPI 82 User manual

HPI 82
Thank you for purchasing the HOOVER induction hob. Please read this instruction manual
carefully before using the hob and keep it in a safe place for future reference.
GR
Εγχειριδιο Χρησησ Επαγωγικησ Εστιασ

Safety Warnings
Your safety is important to us. Please read this
information before using your hob.
Installation
Electrical Shock Hazard
•Disconnect the appliance from the mains
electricity supply before carrying out any
work or maintenance on it.
•Connection to a good earth wiring system is
essential and mandatory.
•Alterations to the domestic wiring system
must only be made by a qualified electrician.
•Failure to follow this advice may result in
electrical shock or death.
Cut Hazard
•Take care - panel edges are sharp.
•Failure to use caution could result in injury or
cuts.
Important safety instructions
•Read these instructions carefully before
installing or using this appliance.
•No combustible material or products should
be placed on this appliance at any time.
•Please make this information available to the
EN-1
By placing the CE mark on this product, we are
confirming compliance to all relevant European safety, health
and environmental requirements which are applicable in
legislation for this product.

person responsible for installing the appliance
as it could reduce your installation costs.
•In order to avoid a hazard, this appliance
must be installed according to these
instructions for installation.
•This appliance is to be properly installed and
earthed only by a suitably qualified person.
•This appliance should be connected to a circuit
which incorporates an isolating switch
providing full disconnection from the power
supply.
•Failure to install the appliance correctly could
invalidate any warranty or liability claims.
Operation and maintenance
Electrical Shock Hazard
•Do not cook on a broken or cracked hob
surface. If the hob surface should break or
crack,switch the appliance off immediately at
the mains power supply (wall switch) and
contact a qualified technician.
•Switch the hob off at the wall before cleaning
or maintenance.
•Failure to follow this advice may result in
electrical shock or death.
Health Hazard
•This appliance complies with electromagnetic
EN-2

safety standards.
•However, persons with cardiac pacemakers or
other electrical implants (such as insulin
pumps) must consult with their doctor or
implant manufacturer before using this
appliance to make sure that their implants
will not be affected by the electromagnetic
field.
•Failure to follow this advice may result in
death.
Hot Surface Hazard
•During use, accessible parts of this appliance
will become hot enough to cause burns.
•Do not let your body, clothing or any item
other than suitable cookware contact the
Induction glass until the surface is cool.
•Beware: magnetisable metal objects worn on
the body may become hot in the vicinity of
the cooktop. Gold or silver jewellery will not
be affected.
•Keep children away.
•Handles of saucepans may be hot to touch.
Check saucepan handles do not overhang
other cooking zones that are on. Keep
handles out of reach of children.
•Failure to follow this advice could result in
burns and scalds.
EN-3

Cut Hazard
•The razor-sharp blade of a hob surface
scraper is exposed when the safety cover is
retracted.Use with extreme care and always
store safely and out of reach of children.
•Failure to use caution could result in injury or
cuts.
Important safety instructions
•Never leave the appliance unattended when in
use. Boilover causes smoking and greasy
spillovers that may ignite.
•Never use your appliance as a work or storage
surface.
•Never leave any objects or utensils on the
appliance.
•Do not place or leave any magnetisable
objects (e.g. credit cards, memory cards) or
electronic devices (e.g. computers, MP3
players) near the appliance, as they may be
affected by its electromagnetic field.
•Never use your appliance for warming or
heating the room.
•After use, always turn off the cooking zones
and the hob as described in this manual(i.e.
by using the touch controls). Do not rely on
the pan detection feature to turn off the
cooking zones when you remove the pans.
EN-4

•Do not allow children to play with the
appliance or sit, stand, or climb on it.
•Do not store items of interest to children in
cabinets above the appliance. Children
climbing on the cooktop could be seriously
injured.
•Do not leave children alone or unattended in
the area where the appliance is in use.
•Children or persons with a disability which
limits their ability to use the appliance should
have a responsible and competent person to
instruct them in its use. The instructor should
be satisfied that they can use the appliance
without danger to themselves or their
surroundings.
•Do not repair or replace any part of the
appliance unless specifically recommended in
the manual. All other servicing should be
done by a qualified technician.
•Do not use a steam cleaner to clean your hob.
•Do not place or drop heavy objects on your
hob.
•Do not stand on your hob top.
•Do not use pans with jagged edges or drag
pans across the Induction glass surface as
this can scratch the glass.
•Do not use scourers or any other harsh
abrasive cleaning agents to clean your
cooktop, as these can scratch the Induction
EN-5

glass.
•If the power supply cable is damaged, it must
only be replaced by a qualified technician.
•This appliance is designed for domestic use
only.
•This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not play
with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
•WARNING: Unattended cooking on a hob with
fat or oil can be dangerous and may result in
fire. NEVER try to extinguish a fire with water,
but switch off the appliance and then cover
flame e.g. with a lid or a fire blanket.
•Metallic objects such as knives, forks, spoons
and lids should not be placed on the hob
surface since they can get hot.
•After use, switch off the hob element by its
control and do not rely on the pan detector.
•The appliance is not intended to be operated
by means of an external timer or separate
remote-control system.
EN-6

Congratulations on the purchase of your new Induction Hob.
We recommend that you spend some time to read this Instruction / Installation
Manual in order to fully understand how to install correctly and operate it.
For installation, please read the installation section.
Read all the safety instructions carefully before use and keep this Instruction /
Installation Manual for future reference.
Product Overview
Top View
Control Panel
1. max. 1800/3000 W zone
2. max. 1800/3000 W zone
3. max. 3000/4000 W zone
4. max. 1400/2000 W zone
5. Flexible zone. 3000/4000 W
6. Glass plate
7. Control panel
1. Heating zone selection controls
2. Timer control
3. Boiling prompt control
4. keep warm control
5. Flexible zone control
6. Power / Timer slider touch control
7. Boost control
8. Keylock control
9. ON/OFF control
1
5
2987
6
3 4
EN-7
6
3
4
1
5
2
7

A Word on Induction Cooking
Induction cooking is a safe, advanced, efficient, and economical cooking
technology. It works by electromagnetic vibrations generating heat directly in
the pan, rather than indirectly through heating the glass surface. The glass
becomes hot only because the pan eventually warms it up.
Before using your New Induction Hob
•Read this guide, taking special note of the ‘Safety Warnings’ section.
•Remove any protective film that may still be on your Induction hob.
Using the Touch Controls
•The controls respond to touch, so you don’t need to apply any pressure.
•Use the ball of your finger, not its tip.
•You will hear a beep each time a touch is registered.
•Make sure the controls are always clean, dry, and that there is no object (e.g.
a utensil or a cloth) covering them. Even a thin film of water may make the
controls difficult to operate.
iron pot
magnetic circuit
ceramic glass plate
induction coil
induced currents
EN-8

Choosing the right Cookware
•Only use cookware with a base suitable for induction
cooking. Look for the induction symbol on the
packaging or on the bottom of the pan.
•You can check whether your cookware is suitable by carrying out
a magnet test. Move a magnet towards the base of the pan. If it
is attracted, the pan is suitable for induction.
•If you do not have a magnet:
1. Put some water in the pan you want to check.
2. Follow the steps under ‘To start cooking’.
3. If does not flash in the display and the water is heating, the pan is suitable.
•Cookware made from the following materials is not suitable: pure stainless steel, aluminium
or
copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and
is the same size as the cooking zone. Use pans whose diameter is as large as
the graphic of the zone selected. Using a pot a slightly wider energy will be used
at its maximum efficiency. If you use smaller pot efficiency could be less than
expected. Pot less than 140 mm could be undetected by the hob. Always centre
your pan on the cooking zone.
Always lift pans off the Induction hob –do not slide, or they may scratch the
glass.
EN-9

Pan Dimension
The cooking zones are, up to a limit, automatically adapted to the diameter of
the pan. However the bottom of this pan must have a minimum of diameter
according to the corresponding cooking zone. To obtain the best efficiency of
your hob, please place the pan in the centre of the cooking zone.
Using your Induction Hob
To start cooking
1. Touch the ON/OFF control.
After power on, the buzzer beeps once, timer control
show “ CL “ ，heating zone selection controls show
“00, indicating that the induction hob has entered
the state of standby mode.
2. Place a suitable pan on the cooking zone that
you wish to use.
•Make sure the bottom of the pan and the surface
of the cooking zone are clean and dry.
3.Touching the heating zone selection control,
and a indicator upon you touched will flash
Cooking zone
The base diameter of induction cookware
Minimum (mm) Maximum (mm)
1,2, 140 220
3220 300
4120 160
Flexible zone 220 220x400
EN-10

4. Adjust heat setting by touching the slider control.
•If you don’t choose a heat setting within 1
minute, the Induction hob will automatically
switch off. You will need to start again at step 1.
•You can modify the heat setting at any time
during cooking.
If the display flashes alternately with the heat
setting
This means that:
•you have not placed a pan on the correct cooking zone or,
•the pan you’re using is not suitable for induction cooking or,
•the pan is too small or not properly centred on the cooking zone.
No heating takes place unless there is a suitable pan on the cooking zone.
The display will automatically turn off after 1 minute if no suitable pan is
placed on it.
When you have finished cooking
1. Touching the heating zone selection
control that you wish to switch off.
2. Turn the cooking zone off by touching the slider
to the left. Make sure the display shows”0”.
EN-11

3. Turn the whole hob off by touching the
ON/OFF control.
4. Beware of hot surfaces
H will show which cooking zone is hot to touch. It will disappear when the
surface has cooled down to a safe temperature. It can also be used as an
energy saving function if you want to heat further pans, use the hotplate
that is still hot.
Using the Boost function
Actived the boost function
1. Touching the heating zone selection control
2. Touching the boost control ,the zone indicator shows “b”and the
power reaches Max.
Cancel the Boost function
1. Touching the heating zone selection control
For which you wish to cancel the boost function.
EN-12

2. a: Touching the boost control “”, then the cooking zone will revert to its
original setting.
b: Touching the slider control, then the cooking zone will revert to the level
you select.
OR
•The function can work in all cooking zones
• The cooking zone returns to its original setting after 5 minutes.
• As the boost function of 1st cooking zone is activated ,the 2nd cooking zone is
limited under level 2 automatically. vice versa
• If the original heat setting equals 0, it will return to 15 after 5 minutes.
Using the Keep Warm function
Actived the keep warm function
1. Touching the heating zone selection control
2. Touching the keep warm control ,the zone indicator show “|”.
EN-13

Cancel the keep warm function
1. Touching the heating zone selection control
2. a:Touching the slider control, then the cooking zone will revert to the level
you select.
b: Touching the function control such as or , then the cooking
zone will revert to the level you previously selected.
FLEXIBLE AREA
• This area can be used as a single zone or as two separate zones, accordingly
to the cooking needs.
• The flexible area is made of two independent inductors that can be controlled
separately. When working as a single zone, if a cookware is moved from one
zone to the other one within the flexible area it will keep the same power level
of the zone where the cookware originally was placed, and the part that is not
covered by cookware will automatically switch off.
•IMPORTANT：Make sure to place the cookwares in the center of the single
cooking zone. In case of large pan, oval, rectangular and long pans make sure
it is placed in the center of the cooking zone covering both logos.
EN-14

Examples of correct pan placement and incorrect pan placement.
As large zone
1. To activate the flexible area as a single large zone, simply press the
dedicated keys.
2. The power setting works as any other normal area.
3. If the pan is moved from the front to the rear part (or vice versa),the
flexible area detects automatically the new position, keeping the same
power.
4. To add a further pan, press again the dedicated keys, in order to detect the
cookware.
Two independent zones
To use the flexible area as two separete zones with different power settings,
press the dedicated keys.
EN-15

Locking the Controls
•You can lock the controls to prevent unintended use (for example children
accidentally turning the cooking zones on).
•When the controls are locked, all the controls except the ON/OFF control are
disabled.
To lock the controls
Touch the keylock control. The timer indicator will show “Loc “
To unlock the controls
1. Touch and hold the keylock control for a while.
2. You can now start using your Induction hob.
When the hob is in the lock mode, all the controls are disable except the
ON/OFF, you can always turn the induction hob off with the ON/OFF control
in an emergency, but you shall unlock the hob first in the next operation
Over-Temperature Protection
A temperature sensor equipped can monitor the temperature inside the
Induction hob. When an excessive temperature is monitored, the Induction hob
will stop operation automatically.
Detection of Small Articles
When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other
small item (e.g. knife, fork, key) has been left on the hob, the hob automatically
go on to standby in 1 minute. The fan will keep cooling down the induction hob
for a further 1 minute.
Auto Shutdown Protection
Auto shut down is a safety protection function for your induction hob. It shuts
down automatically if ever you forget to turn off your cooking. The default
working times for various power levels are shown in the below table: .
Power level
Keep warm
1~5
6~10
11~14
15
Default working timer (hour)
2
8
4
2
1
When the pot is removed, the induction hob can stop heating immediately and
the hob automatically switch off after 2 minutes.
EN-16

People with a heart pace maker should consult with their doctor before
using this unit.
Using the Timer
You can use the timer in two different ways:
•You can use it as a minute minder. In this case, the timer will not turn any
cooking zone off when the set time is up.
•You can set it to turn cooking zones off after the set time is up.
•You can set the timer for up to 99 minutes.
Using the Timer as a Minute Minder
If you are not selecting any cooking zone
1. Make sure the cooktop is turned on.
Note: you can use the minute minder even if you’re not selecting any
cooking zone.
2. Touch timer control , the “10”will be shown in the
timer display where you touched and the “0”flashes.
3. Set the time by touching the slider control. (e.g. 6)
4. Touch timer control again, the “1”will flash.
5. set the time by touching the slider control (e.g.9),
now the timer you set is 96 minutes.
EN-17

6. Buzzer will beep for 30 seconds and the timer
indicator shows “00 “when the setting time
finished.
Setting the timer to turn cooking zones off
If the timer is set on one zone:
1. Touching the heating zone selection control
that you want to set the timer for.
2. Touch timer control , the “10”will be shown on the
timer display and the “0”flashes.
3. Set the time by touching the slider control. (e.g. 6)
4. Touch timer control again, the “1”will flash.
set the time by touching the slider control (e.g.9),5.
now the timer you set is 96 minutes.
EN-18

6. When the time is set, it will begin to count down
immediately. The display will show the remaining
time and the timer indicator flash for 5 seconds.
NOTE: The red dot next to power level indicator
will illuminate indicating that zone is selected.
7. When cooking timer expires, the corresponding
cooking zone will be switch off automatically.
Other cooking zone will keep operating if they are turned on previously.
If the timer is set on more than one zone:
1. When you set the time for several cooking zones simultaneously, decimal
dots of the relevant cooking zones are on. The minute display shows the
min. timer. The dot of the corresponding zone flashes.
(set to 15 minutes)
(set to 45 minutes)
2. Once the countdown timer expires, the corresponding zone will switch off.
Then it will show the new min. timer and the dot of corresponding zone will
flash.
•Touch the heating zone selection control, the corresponding timer will be
shown in the timer indicator.
EN-19