Hotpoint Ariston TCD 971 User manual

1
First time you turn on your dryer
you must select your preferred
language see Display
English, 1
Contents
Installation, 2
Warnings, 4
Care and Maintenance, 6
Control Panel, 8
Laundry, 8
The Display, 9
Start and Programmes, 11
Troubleshooting, 15
Assistance, 16
GB
TUMBLE DRYER
TCD 971
Instruction booklet
!This symbol reminds you to read this
instruction manual.
!Keep this manual at hand for immediate reference whenever
necessary. Always store this manual close to the tumble dryer and
remember to pass it on to any new owners when selling or tran-
sferring the appliance, so they may familiarise with the warnings
and suggestions herein contained.
!Read these instructions carefully: the following pages contain
important information on installation and useful suggestions for
operating the appliance.
www.hotpoint.eu
Italiano, 33
Ελληνικά, 17
GR IT
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Hotpoint Ariston
TCD 971 6CY1 o cerca il tuo prodotto tra le migliori offerte di Lavatrici eAsciugatrici

2
GB
Where to put your dryer
• Place your dryer at a
distance from gas ranges,
stoves,heaters,orcooktops
becauseflamescandamage
the appliance. The dryer
should be installed in an
ambient room temperature
of between 20 to 23°C
for optimum performance.
But will function if the room is between 14 and
30°C. If you are going to install the appliance
under a work counter, be sure to leave a 10 mm
space between the top and any other objects
on or above the machine and a 15 mm space
between the sides and lateral furnishings or
walls. This is to ensure proper air circulation.
The appliance must be installed with the rear
surface placed against a wall.
Ventilation
• When the dryer is in use, there has to be
adequate ventilation. Make sure you put your dryer
in an environment that is not damp and has proper
air circulation throughout. Airflow around the dryer
is essential to condense the water produced during
the washing, the dryer will not operate efficiently in
an enclosed space or cupboard.
! If using the dryer in a small or cold room
some condensation will be experienced.
! We do not recommend that the dryer is
installedin acupboardbutthedryermust never
be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite
side to that of the dryer door.
1
2
H<1m
1
2
Fig. A Fig. B
Water Drain
Ifthemachineispositionedclosetoadrainitispossibletodrainthe
condensed water directly without using the waterbottle. In which
case it is no longer necessary to empty the water bottle at the end
ofeachcycle.IftheDryerispositionedaboveorclosetoaWashing
Machine the same drainage can be used. Just remove the tube
indicated in figure A and connect it to the drainage. If the drainage
is further away than the length of the tube it is possible to buy and
connect a tube of the same diameter and the necessary length in
order to reach the drain. To install the new tube just substitute the
existing one as indicated in figure Binserting it in the same place.
!The drain tube has to be below 1 m from the bottom of
the Dryer.
! Once the Dryer has been installed please assure that
the drain tube is not bent or kinked.
Electrical connections
Before plugging the appliance into the socket,
check the following:
• Make sure your hands are dry.
• The socket must have an earth connection.
• The socket must be able to withstand
the machine’s maximum power output as
indicated on the rating plate.
• The power supply voltage must fall within
the values indicated on the data plate.
• The socket must be compatible with the
dryer’s plug. Should this not be the case,
replace the plug or the socket.
! DO NOT USE EXTENSION CORDS.
! The dryer must not be installed outdoors,
even if the space is sheltered. It can be very
dangerous if exposed to rain or storms.
! Once installed, the dryer’s electrical wire and
plug must be within reach.
! The power cord must not be bent or
squashed.
! If the plug being replaced is a non-rewirable
type, then the cut-off plug must be disposed of
safely. DO NOT leave it where it can be inserted
into a socket and create a shock hazard.
! The power must be regularly checked. If the
supply cord is damaged, it must be replaced
by the manufacturer, its service agent or
similarly qualified persons in order to avoid
a hazard. (see Assistance). New or longer
electric cords are supplied by authorised
dealers at a supplementary cost.
! The manufacturer denies any
responsibility should any of these rules
not be followed.
!If in doubt about any of the above
consult a qualified electrician.
Levelling the tumble dryer
The dryer must be installed level for correct
operation.
When you have installed your dryer in its final
location check that it is level first side-to-side,
then front to back. If the dryer is not level,
Installation
10 mm
15 mm 15 mm

3
GB
This household tumble drier is a Condenser
The weighted Annual Energy Consumption (AEc)* kWh 1) 340.0
This household tumble drier is a Automatic
Energy consumption full load; Edry - kWh 2) 2.85
Energy consumption partial load; Edry½ - kWh 2) 1.56
Power consumption: off-mode (Po) - Watts 0.14
Power consumption: left-on mode (Pl) - Watts 3.36
Prog. Time - weighted (Tt) full & partial load - minutes 3) 197
Full load (Tdry) - minutes 261
Partial load (Tdry½) - minutes 149
weighted (Ct) full & partial load 3) 81
full load (Cdry) 81
partial load (Cdry½) 81
Airborne acoustical noise emissions - dB(A) re 1 pW 70
70
Average condensation efficiency - %
the information in the label and the fiche relates. The standard cotton program is
suitable to dry at cupboard level (0%) cotton laundry and is the most efficient
programme in terms of energy consumption. Partial load is half the rated load.
2) based on 160 drying cycles of the standard cotton programme at full and
partial load, and the consumption of the low-power modes. Actual energy
consumption will depend on how the appliance is used.
3) Weighted average of 3 cycles at full load and 4 cycles at half load.
Regulation 932/2012.
0.68
Energy efficiency class on a scale from A+++ (low
consumption) to D (high consumption)
A+
Duration of the 'left-on mode' for power management system -
minutes
30
Condensation efficiency class on a scale from G (least efficient)
to A (most efficient)
B
Product Data - Regulation 392/2012.
Brand
HOTPOINT/ARISTON
Model
TCD 971 6CY1 (EU)
Rated capacity of cotton laundry for the "standard cotton
programme" at full load - kg
9.0
Maximum load sizes: 9kg
adjust the two legs up or down until your
dryer is level.
Preliminary information
Once you’ve installed your dryer and before you use it, clean
the inside of the drum to remove any dust that could have
accumulated during transportation.
Warning ! Before you use your dryer ensure that its has
been in a upright position for at least 6 hours.

4
GB
Warnings
!This appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons
and must be followed carefully.
General safety
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
• After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that
children do not use it as a toy.
• Children should be supervised to ensure
that they do not play with the dryer.
• Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
at the front of the dryer should never be
obstructed (see Installation).
• Never use the dryer on carpeting where
the pile height would prevent air from
entering the dryer from the base.
• Check to see if the dryer is empty before
loading it.
• The back of the dryer could become
very hot. Never touch it while in use.
• Do not use the dryer unless the filter,
watercontainer and condenser are securely in
place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are still
warm items inside.
• Clean the filter after each use (see
Maintenance).
• Empty the Water Container after each use
(see Maintenance).
• Clean the Heat Pump filter unit at regular
intervals (see Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire in your tumble
dryer, the following should be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed and
been through the spin cycle. It is a fire hazard
to dry items that HAVE NOT been washed
with water.
• Do not dry garments that have been treated
with chemical products.
• Do not tumble dry items that have been
spotted or soaked with vegetable or cooking
oils, this constitutes a fire hazard. Oil-affected
items can ignite spontaneously,especially
when exposed to heat sources such as
a tumble dryer. The items become warm,
causing an oxidisation reaction with the
oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent heat
from escaping and so create a fire hazard.
If it is unavoidable that fabrics containing
vegetable or cooking oil or those that have
been contaminated withhair care products
be placed in a tumble dryer they should first
be washed with extra detergent - this will
reduce, but not eliminate the hazard. They
should not be removed from the dryer and
piled or stacked while hot.
• Do not tumble dry items that have previously
been cleaned in or washed in, soaked in
or soiled with petrol/gasoline, dry cleaning
solvents or other flammable or explosive
substances. Highly flammable substances
commonly used in domestic environments
including cooking oil, acetone, denatured
alcohol, kerosene, spot removers, turpentine,

5
GB
waxes and wax removers. Ensure these
items have been washed in hot water with
an extra amount of detergent before being
dried in the tumble dryer.
• Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
• Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by
the manufacturer of the fabric softener
product.
• Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
• Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• Remove all objects from pockets such as
lighters and matches.
!WARNING: Never stop the dryer before
the end of the drying cycle unless all
items are quickly removed and spread
out so that the heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water before
tumble drying (if you use a washing machine first, select
a high spin cycle). Doing this will save time and energy
during drying.
• Always dry full loads - you save energy: single items or
small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).

6
GB
Disconnecting the power supply
!Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying. Clean the filter once
drying is completed, by
rinsing it under running
water or cleaning it
with a vacuum cleaner.
Should the filter become
clogged, the flow of air
inside the dryer will be
seriously hampered:
drying times becomes
longer and more energy
is consumed. Moreover,
the dryer may become
damaged.
The filter is located in
front of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic handle upwards (see
Picture).
2. Clean the fluff off the filter and replace it
correctly. Ensure that the filter is pushed fully
home.
!Do not use the dryer unless the filter has
been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items
(handkerchiefs) that could have been left inside the dryer.
Cleaning the drum
!Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on the
stainless steel drum surface: it may be caused by a combina-
tion of water and/or cleaning agents such as wash-softeners.
This coloured film does not affect the dryer’s performance.
Emptying the water container after each
cycle
2
Remove the water container and
empty it into a sink or other
suitable drain outlet, then
replace it correctly.
Always check the water
container and empty it before
starting a new drying cycle.
-Failure to empty the water container may cause the
following:
- The dryer stops heating (thus the load may still be
damp at the end of the drying cycle).
Priming the Water Collection System
When your dryer is new, the Water Container will not
collect Water until the system is primed, this will take
1 or 2 drying cycles. Once primed it will collect Water
during every cycle.
Cleaning the Heat Pump Filter Unit
• Periodically (every 5 drying cycles) remove
Heat pump filter unit and clean any build up
of fluff from the surface of the filter by rinsing
it under running water or with your vacuum
cleaner.
We however recommend that you clean this
filter after every drying cycle to optimize the
dryers performance.
To remove Heat pump
filter unit:
1. Unplug the dryer and
open the door.
2. Remove the filter unit
by rotating the 4 clips
to the vertical position
then pulling the filter
unit towards you.
3. Separate the two
parts of the filter unit and clean the surface of
the filter.
!Warning: The front of
the heat pump is made
from thin metal plates.
Take care that you do
not damage these or cut
yourself when cleaning,
removing or replacing
the filter unit.
4.Whenever you clean the Heat pump filter
unit always clean any build up of fluff from
Care and maintenance

7
GB
the surface of the metal
plates. Carefully clean
this fluff off with a damp
cloth,sponge or vacuum
cleaner. Never use your
Fingers.
5. Assemble the two
parts of the filter clean
the surface of the
seals and replace with the 4 clips into the
horizontal position, sure that the catches
have been secured.
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be
cleaned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the Heat pump filter unit and from the filter
area, using a vacuum cleaner every so often.
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and
mechanical parts work safely (see Assistance).
Water container
Heat pump
filter unit
Cover
Catches
Filter
Handle
Air intake
Heat Pump Protection System
The heat pump system has a compressor protection
feature that operates if you open the door or there is a
power disruption or if you turn off the dryer. This system
will prevent the heat pump compressor from starting for
5 minutes after the door is closed and the programme is
started.
Quick Tips
!Remember to clean your filter and Heat
Pump filter unit after each load.
! Remember to empty your water container
after each load.
! Doing this will keep your machine working
at its BEST!
2
Model & Serial numbers Rating plate
Adjustable feet

8
GB
Control panel
PROGRAMME
Selection Buttons
Display Unit
ON/OFF
Button CHILD LOCK &
OPTIONS
Buttons & Lights
START/PAUSE
Button & Light
The ON/OFF button : - if pressed when the dryer is
running: If the display shows TURNING OFF the dryer
stops. If the display shows PRESS AND HOLD , hold the
botton and the display counts down 3, 2, 1 and then stops.
Press and hold again for more than 3 seconds, the display
briefly shows POWER ON .
The PROGRAMME selection buttons set the programme:
press the button corresponding to the programme you
want to select (see Start and Programmes).
The OPTION buttons/indicators: these buttons select
available options for your selected programme (see The
Controls). The indicators on the display unit next to the
bottom buttons light to show that the option has been
selected.
The START/PAUSE button/light starts a selected
programme. When a programme is running, pressing this
button in pauses the programme, there will be one beep,
the display will show PAUSE and the dryer stops.
The light is green when the programme is running, flashing
Sorting laundry
• Check the symbols on the care labels of the various gar-
ments to verify whether the garments can be safely tumble
dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
!Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum.
The following values indicate the weight of dry garments:
Natural fibres: maximum kg
Synthetic fibres: maximum kg
Laundry
amber if the programme has been paused or flashing
green if on standby waiting to start a programme (see
Start and Programmes).
Note: This light also flashes amber during the Post
Care phase of a programme.
The Display Unit gives warnings and information about
the programme selected and its progress (see next page).
The CHILD LOCK button/icon : Press and hold this
button after selecting your programme and any options,
this prevents the programme settings from being changed,
the display will briefly show LOCKED . When the icon
is lit, the other buttons are disabled. Hold the button to
cancel and the icon will go out, the display will briefly show
UNLOCKED .
Note: This tumble dryer, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press and hold the ON-OFF button
until the display briefly shows POWER ON , and the dryer
then reactivates.
!Do not overload the dryer as this may result is reduced
drying performance.
Care labels
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
3
9

9
GB
The Display
Selecting your language
The first time you turn on your dryer you should select your preferred language from the available list.
Understanding the display
Programme selection and display
The selected programme is shown on the first line of the display, this message is shown while the programme is running.
Eight of the buttons have two selections, press the button once for the first choice and press again for the second choice, your
selected programme is displayed. The final button selects My Cycle.
My Cycle. When you select the My Cycle button the Display will show your selected programme with ‘M’ before its
name. ie. M STANDARD COTTON (see Start and Programmes).
Dryness levels
During programme selection for an automatic programme that has different dryness levels available (see Programmes
Table).
The second line of the display shows the dryness level you require, for each press of the Dryness Level button the next
option from the list below is selected and displayed. The display also shows 1 to 7 bars depending on your selection and
these are displayed during the programmes progress.
! Some automatic programmes do not allow the dryness level to be changed or do not have all the dryness level options.
To change: the language current selection must flash, on the first
line of the display.
- Press the On/Off button to turn off the display then press and hold
all 3 buttons: Heat Level, Timed Dry, and Sensor Dry
for 5 seconds.
- Press the Heat Level or the Timed Dry button to scroll up
or down through the list.
- When your required language is flashing on the top line of the
display, pressing the Sensor Dry button will select your choice.
DAMP
IRON DRY
HANGER PLUS
HANGER DRY
LIGHT DRY
CUPBOARD DRY
EXTRA DRY
Dries your items ready to be ironed using a machine or rotary ironer.
Dries your items ready to be ironed with a hand iron.
Dries your delicate items ready to be hanged for final drying.
Dries your items ready to be hanged for final drying.
Dries your delicate items ready to be put away.
Dries your items ready to be put away.
Dries your clothes ready to be worn.
Programme progress
The second line of the display shows the status of the programme as it progresses:
(long messages scroll across the line)
(if option Crease Care selected)
DRY
COOL TUMBLE
HEATING
READY
END OF CYCLE, CREASE CARE
END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE

10
GB
The Display
Timed drying
After selecting a programme that has a Timed Dry
option, press the Timed button and the display will
increment the selected time, each time you press and
release the button (see Start and Programmes).
Delay and Time to End
Some programmes can have a delayed start
(see Start and Programmes). Press the ,
Delay button and the icon flashes.
Each press of the Delay button advances
the delay setting in 1 hour increments, from:
to ,then and then after a couple of
seconds cancels the delay.
The delay time is shown on the display next to the Delay button.
The display counts down the minutes of the delay period after the Start/Pause button is pressed. The second line of the
display shows STARTS IN
You can change or cancel the delay time selected anytime if you wish.
After the Start/Pause button is pressed the Delay or Time to End is displayed in hours and minutes and counts down each
minute.
Time to End
After the delay period finishes, or for all the programme if delay not selected, this part of the display will show:
- the estimated time to the end of the programme, for automatic programmes
- the actual time remaining during a timed programme
When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.
When Automatic programmes are selected the time displayed is an estimate of the time remaining. When the programme is
selected the display shows the time required to dry a full load. The time remaining is constantly monitored during the drying
cycle and is updated to show the best forecast.
The colons between the hours and minutes in the display flash to show the time is counting down.
Each press reduces the time duration and number of available time options depending on the programme/material
selected.
The Timed Dry icon is displayed next to the time..
The selected time remains displayed after the programme starts, but can be changed anytime you wish.
My Cycle button:
First time you press this button the display will show PRESS AND HOLD TO STORE
After selecting your favorite programme and options you can save these settings by pressing and holding in the My Cycle
button for at least 5 seconds, the top line will show a flashing Mfollowed by the selected programme. The
buzzer will then beep and the second line of the display shows MEMORY
The next time you need this programme press the M, button, then the Start/Pause button (and this programme will run.
If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold
in the Mbutton (as above).

11
GB
Choosing a programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see Laundry).
3. Open the door and make sure the filter is clean and in
place and the water container is empty and in place (see
Maintenance).
4. Load the machine and make sure items are not in the way
of the door seal. Close the door.
5. If the Display is not lit: Press the ON/OFF button .
6. Press the Programmes Selection button that corresponds
with the type of fabric being dried by checking the
Programmes Table (see Programmes) as well as the
indications for each type of fabric (see Laundry).
- if the Mbutton is selected; steps 7 and 8 are not required
(see below).
7. Choose Timed Drying or Dryness Levels option:
- If Timed Drying press and release the Timed button until
the required time is displayed.
or - To change from default dryness setting, press and
release the Dryness Levels button until required level is
indicated.
!See Programmes Table, for more details: availability of
Dryness Levels, Timed Dry and Options.
8.Set a delay time and other options if necessary (see The
Display).
Start and Programmes
9.Press the Start/Pause button to begin. The display
will show the estimated time to end. During the drying
programme, you can check on your laundry and take out
items that are dry while others continue drying. When you
close the door again, press the Start/Pause button in
order to resume drying.
If you open the door to check your laundry you will extend
the drying time as the heat pump compressor will not start for
5 minutes after you close the door and press the Start/Pause
button (see The Controls).
10. During the last few minutes of Drying Programmes,
before the programme is completed, the final COOL
TUMBLE phase is entered (fabrics are cooled), this phase
should always be allowed to complete.
11. At the end of the drying cycle a message is displayed:
- if END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE
is shown, the buzzer will beep 3 times (Note: If the SOUND
option was selected the buzzer beeps 3 times every 30
seconds for 5 minutes).
- if END OF CYCLE, CREASE CARE is shown, Crease Care
option has been selected and if you do not remove the
laundry immediately, the dryer will tumble occasionally for 10
hours or until you open the door, the buzzer will beep 3 times
to confirm the programme is completed.
12. Open the door, take the laundry out, clean the filter and
replace it. Empty the Water Container and replace it (see
Maintenance).
13. Unplug the dryer.
Drying times
Drying times are approximate and may vary depending on the following:
• Amount of water retained by items after the spin cycle: towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture and thickness may have different drying times.
• Amount of laundry: single items and small loads may take longer to dry.
• Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete
drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature of the room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the drying process. We suggest removing these items and replacing them
in the dryer once they have been shaken out: repeat this procedure several times during the course of the drying cycle.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep them soft and fluffy.
The drying times provided refer to the automatic Cupboard dry programmes.
The Timed drying settings are also indicated to enable you to select the most suitable timed option.
The weight refers to dry items.

12
GB
n° Programme Description of program
The duration of the drying cycles can be checked on the display1.
1
Standard
Cotton
• This is a programme for cotton items.
• The Standard Cotton programme to EU Regulation 392/2012 is Programme 1 selection with High Heat and Dryness Level
Cupboard Dry (the standard/default starting configuration). It is the most efficient programme in terms of energy consumption
(to EU.392/2012).
max
Shirts
Cottons
• This is a programme for shirts made from cotton.
• Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If this
is the case, try turning the shirts inside out and running the programme again for a short period.
3 kg
2
Bed & Bath1
• This is a programme for cotton towels and sheets.
• Loads dried using the Extra Dry setting are usually ready to use, the edges or seams may be slightly damp especially on
large items. If this is the case, try opening them out and running the programme again for a short period.
max
Anti
Allergy
• This programme has the ‘Seal of Approval’ endorsement from Allergy UK, which reflects the effective reduction and
elimination of allergens from the clothes with the special Anti Allergy cycle. With this programme, thanks to the achie-
vement of constant temperature for an extended period of time, the effects of the most common allergens (including
House Mites and Pollen) are neutralised.
• Can be used on a full size wet load to dry and treat, or on a 4 kg dry load just to treat your laundry. If the display shows
CLEAN FILTER TO ENSURE ANTI ALLERGY ACTION : Clean the filter and re-start the programme.
max or 4 kg
3
Synthetics
• This is a programme for items of Synthetic with low heat setting or Synthetic/Cotton mixtures with medium heat setting.
3 kg
Shirts
Sytnthetic
• This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such as
polyester and cotton.
• Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If this
is the case, try turning the shirts inside out and running the programme again for a short period.
3 kg
4
Jeans
• This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.
• Do not mix dark and light coloured items.
• It can also be used on other garments made from the same material, such as jackets.
• Loads dried using the Extra Dry setting are usually ready to wear, the edges or seams may be slightly damp. If this is the
case, try turning the jeans inside out and running the programme again for a short period.
! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.
3 kg
Duvet
! Take care with this programme DO NOT dry any items that are damaged which could result in the filling blocking the filter
and air vent resulting in a fire hazard.
• Must only be used on single size duvets: NOT suitable for double or king size items.
• Loads dried using this programme are usually ready to use, but may be slightly damp in places. If this is the case, try
opening them out and shaking them and running the programme again for a short period.
• Also suitable for down filled jackets.
• Select high heat for Cotton Duvets and medium heat for Synthetic duvets.
-
Note:
1 - The duration of the program will depend on the size of the load, types of textiles, the spin speed used in your washer and any extra options
selected.

13
GB
Note:
1 - The duration of the program will depend on the size of the load, types of textiles, the spin speed used in your washer and any extra options
selected.
n° Programme Description of program
The duration of the drying cycles can be checked on the display1.
5
Wool
• This is a programme for tumble dryer safe garments marked with the symbol .
• We recommend that garments are turned inside out before drying.
• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly
damp. Allow these to dry naturally as over-drying could damage garments.
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.
! This programme is not suitable for Acrylic garments.
1 kg
Silk
• This is a programme for drying your delicate silk.
• Loads dried using the Cupboard Dry setting are usually ready to use, but on some garments the edges may be slightly
damp. If this is the case, try opening them out or turn items inside out and running the programme again for a short
period.
0,5 kg
6
Delicates
• This is a programme for drying your delicate clothes ie. Acrylics.
• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly
damp. If this is the case, try turning items inside out and running the programme again for a short period.
2 kg
Baby
• This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille) and for
drying your delicate clothes.
• DO NOT dry items such as bibs and nappy pants with plastic coverings.
• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly
damp. If this is the case, try turning items inside out and running the programme again for a short period.
2 kg
7
Cuddly Toy
• With this programme you can remove dust easier and wash the cuddly toys more often because the drying time is very
much reduced compared to drying in the open air. It is a delicate drying cycle that dries at low temperature and with soft
mechanical action to maintain at best the original look and shine of the fur.
Note: For allergy protection, just freeze cuddly toys for 24 hours then wash and dry them. Repeat every 6 weeks.
• Before drying remove accessories such as clothes, collars or sound boxes and protect plastic eyes with masking tape
after drying them with a cloth.
• The programme time will vary dependant on the exact make up of the load. The maximum load should not exceed 2.5
kg and no individual item should be greater than 600 g.
2,5 kg
Heat & Enjoy
• This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for warming
clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature), the display shows HEATING
and runs at this temperature for a maximum of 4 hours or until you stop the cycle by opening the door when the display
shows READY .
Note: The Start/Pause button is disabled during this programme.
3 kg
8
Refresh
!‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.
• It can be used on any load size, but is more effective on smaller loads.
• Do not overload your dryer (see Laundry).
• This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.
-
Pre Iron
• ‘Pre Iron’ is a treatment cycle for use with dry clothes and reduces creases in order to facilitate ironing and folding, it has a
maximum duration of 15 minutes.
!‘Pre Iron’ is not a drying programme and should not be used for wet articles of clothing.
• For best results:
1. Do not load more than the maximum capacity. These numbers refer to the dry weight: (Fabric-Maximum load) Cotton and
Cotton mixtures-2.5 kg; Synthetics-2 kg; Denim-2 kg.
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put them away in the closet.
Should this not be possible repeat the programme.
2,5 kg

14
GB
The Controls
!Warning, after pressing the START/PAUSE button ,
the programme cannot be changed. To change a selected
programme, press the START/PAUSE button the light
flashes Amber to indicate the programme is paused. Select
the new programme and any options required, the light will
then flash green. Press the START/PAUSE button again
and the new programme will start.
• Option buttons
These buttons serves to personalise the selected
programme according to personal requirements.
Not all options are available for all programmes.
Some options are incompatible with the ones
previously set. If the button of any unavailable option
is pressed, the buzzer will beep 3 times. If the option
is available, the option light will stay on.
Delay Timer (Time Delay)
The start of some programmes (see The Display and
Programmes tables) can be delayed for up to 24 hours.
Ensure the water container is emptied before setting a
delayed start.
Crease Care
The pre-care option is only available if a delayed start has
been selected. It tumbles the clothes occasionally during
the delayed period to help prevent creases developing. The
post-care option occasionally tumbles the clothes after end
of the drying and cool tumble cycles to prevent creases
developing, should you not be available to remove the load
immediately the programme is complete
Note: The START/PAUSE light flashes Amber during
this phase. Selecting this option enables both the pre and
post care functions if appropriate.
Heat Level button, Display and Icons
Not all programmes allow you to change the heat level and
some programmes allow all three heat level options:
Low, Medium and High.
When the heat level options are available pressing this
button changes the heat level and the display briefly shows
the selected heat level, along with a display of the selected
level icon:
HIGH HEAT MEDIUM HEAT LOW HEAT
Extra Care
This Anti-Ageing function for Cottons helps to maintain the
brightness of your laundry for a long time, thanks to the
correct drum rotation (reduced in the last part of the cycle)
and the correct temperature.
Less Tangled
This option has the drum movement modified to give a
tumbling action that reduces tangling and knotting of your
clothes. The Less Tangled option gives best results when
used with smaller loads.
Ready to Iron
This option allows you to dry loads where only some of the
items need ironing and you do not wish to fully dry those
items. When Iron Dry level is reached, a buzzer sounds to let
you know that the items that need ironing can be removed.
The dryer then stops and the START/PAUSE light flashes
orange. Remove the items you wish to iron, close the
door and press the START/PAUSE button , the dryer
continues until the remaining items reach the selected dryness
level. It can be used for load sizes up to 3kg.
.
• TIME DISPLAY
The display shows either the amount of time delay remaining or
an indication of the amount of time left for a drying programme
(see The Display). The display also shows if there is a problem
with your dryer, if this occurs the display will show F followed by
a fault code number (see Troubleshooting).
• Empty Water Container
(Messages about emptying can be ignored if you have plumbed
your dryer into a drain as there is no need to empty the water
container). Messages are displayed to reminds you to empty
the water container (see The Display). If the water container fills
during a programme, the heater turns off and the dryer does a
period of Cool Tumble. After this it stops and a message tells
you to EMPTY THE WATER CONTAINER . You must empty the water
container and restart the dryer or the clothes will not dry. After
re-starting the dryer the message will take a few seconds to go
out. To avoid this always empty the water container each time
you use the dryer (see Maintenance).
• Door Opening
Opening the door during a programme will stop the dryer and
have the following effects:
Note: The START/PAUSE light flashes Amber during the
Post Care phase of a programme
 • The display shows PAUSED .
• During a delay phase the delay will continue to count down.
The START/PAUSE button must be pressed to resume
the delay programme. The display will change to show current
status.
• The START/PAUSE button must be pressed to resume
the programme. The display will change to show the
current status.
• During the Post Care phase, the programme ends. Pressing
the START/PAUSE button will restart a new programme
from the beginning.
• Note
If you have a power cut, switch off the power or remove the
plug. When power is restored, press and hold the On/Off
button until the display briefly shows POWER ON and the dryer
reactivates. Then press the START/PAUSE button and the
programme will resume.

15
GB
Troubleshooting
Possible causes / Solution:
• The plug is not plugged into the socket, or not making contact.
• There has been a power failure.
• The fuse has blown. Try to plug another appliance into the socket.
• You are using an extension cord? Try to plug the dryer’s power cord directly into the
socket.
• The door is not closed securely?
• The programme has not been set properly (see Start and Programmes).
• The Start/Pause button has not been pressed (see Start and Programmes).
• You have set a delayed time (see Start and Programmes).
• The filter has not been cleaned (see Maintenance).
• The water container needs emptying? The empty water message is displayed? (see
Maintenance).
• The heat pump filter needs cleaning? (see Maintenance).
• The temperature setting is not ideal for the type of fabric you are drying (see Start
and Programmes, and see Laundry).
• The correct drying time has not been selected for the load (see Laundry).
• The air intake grille is obstructed (see Installation, and see Maintenance).
• The items were too wet (see Laundry).
• The dryer was overloaded (see Laundry).
• The water container was probably not emptied at the start of the programme. Do not
wait for the empty water signal, always check and empty the container before starting
a new drying programme (see Maintenance).
• This is normal, the:
message is shown as a reminder to empty the container (see The Display and Start
and Programmes).
!For safety the dryer has a maximum programme time of 5 hours. If an automatic
programme has not sensed the required final moisture in this time the dryer will
complete the programme and stop. Check the above points and run the programme
again, if the results are still damp, contact the Service Centre (see Service).
• If the display shows a fault:
- Turn off and remove the plug. Clean the filter and the heat pump filter unit (see
Maintenance). Then replace the plug, turn on and start another programme. If a fault
is then displayed: Note down the code and contact the Service Centre (see Service).
• The dryer is in ‘Demo’ mode. Press and hold both the On/Off and Start/Pause
buttons for 3 seconds. The display will show DEMO OFF for 3 seconds and then the
dryer will resume normal operation.
• The dryer has gone into standby mode to save power. This occurs if you have had a
power cut or leave your dryer either without starting a programme or after your drying
programme has finished.
- Press and hold the On/Off button and the lights will come on.
Problem:
The tumble dryer won’t start.
Drying cycle will not begin.
Its taking a long time to dry.
Empty water message is displayed but
the dryer has only been running for a
short period.
Empty water message is displayed and
the water container is not full.
Programme finishes and clothes are
damper than expected.
The display shows a fault
code F followed by one or two
numbers.
The display briefly shows
DEMO ON every 6 seconds.
The lights on the dryer control
panel are off although the
dryer is switched on.
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following
troubleshooting suggestions:
END OF CYCLE, CLEAN FILTER AND EMPTY THE WATER BOTTLE

16
GB
Service
Information on recycling and disposal
As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components
to reduce costs for our customers and to minimise materials wastage.
• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the
appliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.
Disposal of old household appliances
The European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposedof in the normal unsorted municipal waste stream. Old appliances must be
collected separately in order tooptimise the recovery and recycling of the materialsthey contain and reduce the impact on
human healthand the environment. This dryer has a sealed heat pump unit containing Fgases which should be recovered
and destroyed.The crossed out “wheeled bin” symbol on theproduct reminds you of your obligation,thatwhen you dispose of
the appliance it must beseparately collected.Consumers should contact their local authority orretailer for information concer-
ning the correct disposalof their old appliance.
This appliance has been designed, constructed and distributed in compliance with the
requirements of European Directives:
- LVD 2014/35/EU, EMC 2014/30/EU and RoHS 2011/65/EU.
Heat Pump System
This dryer is fitted with a sealed heat pump system to dry
your clothes. To operate, the heat pump contains fluorinated
greenhouse gases ( F gases) which are covered by the Kyoto
Protocol. These F gases are contained in a hermetically
sealed unit. This sealed unit contains kg of the F gas
R134a which acts as a refrigerant. GWP = 1430 (0.4 t C02).
If the sealed unit fails then it must be replaced by a new
sealed unit. Contact your nearest service centre for advise.
Note: The gases contained in the sealed unit are not
hazardous to health, but if they escape they will have an
impact on global warming.
Before calling the Service Centre:
• Use the troubleshooting guide to see if you can solve the
problem yourself (see Troubleshooting).
• If not, turn off the dryer and call the Service Centre closest to
you.
Spare Parts
This dryer is a complex machine. Repairing it yourself or
having a nonauthorised person try to repair it could cause
harm to one or more persons and to the machine, and could
invalidate the spare parts warranty.
Call an authorised technician if you experience problems
while using the machine.
Please note that it is an offence for an unqualified person
to undertaken any servicing or repair work that involves
breaking into the sealed heat pump unit.
What to tell the Service Centre:
• Name, address, and post code;
• telephone number;
• the type of problem;
• the date of purchase;
• the appliance model (Mod.);
• the dryer serial number (S/N).
This information can be found on the data label inside the
door of the machine.
0,29

17
GR
Contents
Εγκατάσταση, 18
Προειδοποιήσεις, 20
Φροντίδα και συντήρηση, 22
Πίνακας χειρισμού - Μπουγάδα, 24
ΗΟθόνη, 25
Εκκίνηση και προγράμματα, 27
Προβλήματα και λύσεις, 31
Υποστήριξη, 32
TCD 971
GR
Οδηγίες χρήσης
ΣΤΕΓΝΩΤΗΡΙΟ
!Το σύμβολο αυτό σου θυμίζει να
διαβάζεις αυτό το εγχειρίδιο οδηγιών.
!Να διατηρείτε εύχερα το παρόν εγχειρίδιο ώστε να μπορείτε
να το συμβουλεύεστε εύκολα οποτεδήποτε. Να διατηρείτε το
εγχειρίδιο πλησίον του στεγνωτηρίου. Στην περίπτωση που η
συσκευή πωληθεί ήπαραχωρηθεί σε άλλα άτομα, θυμηθείτε να
τους παραδώσετε αυτό το εγχειρίδιο, ώστε να μπορούν και οι
νέοι κάτοχοι να γνωρίζουν τις προειδοποιήσεις και τις υποδείξεις
για τη χρήση του στεγνωτηρίου.
!Διαβάστε προσεκτικά αυτές τις οδηγίες: οι σελίδες που
ακολουθούν περιέχουν σημαντικές πληροφορίες για την
εγκατάσταση και χρήσιμες υποδείξεις για τη λειτουργία της
οικιακής ηλεκτρικής συσκευής.
www.hotpoint.eu
Την πρώτη φορά που
θα ενεργοποιήσετε το
στεγνωτήριο σας πρέπει
να επιλέξετε την επιθυμητή
γλώσσα βλ. ΗΟθόνη
Ελληνικά

18
GR
Που εγκαθίσταται το στεγνωτήριο
• Οι φλόγες μπορεί να
προξενήσουν ζημιές
στο στεγνωτήριο, που
πρέπει να εγκατασταθεί
μακριά από κουζίνες
αερίου, θερμάστρες,
καλοριφέρ ήπλαίσια
μαγειρέματος.
Το στεγνωτήριο πρέπει
να εγκατασταθεί σε ένα
χώρο με θερμοκρασία μεταξύ των 20 και 23
°C για να έχετε τις βέλτιστες επιδόσεις. Σε
κάθε περίπτωση, ησωστή λειτουργία είναι
εγγυημένη μεταξύ των 14 και 30°C.
Αν ηηλεκτρική συσκευή πρέπει να
εγκατασταθεί κάτω από έναν πάγκο
εργασίας πρέπει να αφήσετε ένα χώρο 10
mm μεταξύ του επάνω πάνελ της ηλεκτρικής
συσκευής και άλλων αντικειμένων
ευρισκόμενων πάνω από αυτό και ένα χώρο
15 mm μεταξύ των πλευρών της ηλεκτρικής
συσκευής και των τοιχωμάτων ήτων
γειτονικών σε αυτό επίπλων. Με τον τρόπο
αυτό διασφαλίζεται επαρκής κυκλοφορία
αέρα.
Ησυσκευή πρέπει να εγκατασταθεί με την
πίσω επιφάνεια τοποθετημένη κόντρα σε
τοίχο
Αερισμός
• Όταν το στεγνωτήριο είναι ενεργό πρέπει να υπάρχει
επαρκής αερισμός. Βεβαιωθείτε ότι εγκαθιστάτε το
στεγνωτήριο σε χώρο χωρίς υγρασία και που διαθέτει
κατάλληλη κυκλοφορία αέρα. Ηροή αέρα πέριξ του
στεγνωτηρίου είναι βασική για να επιτραπεί ησυμπύκνωση
του παραγόμενου νερού κατά το πλύσιμο. Το στεγνωτήριο
δεν λειτουργεί σωστά αν τοποθετηθεί σε χώρο κλειστό ή
στο εσωτερικό ενός επίπλου.
!Αν το στεγνωτήριο χρησιμοποιείται σε μικρό ήκρύο
δωμάτιο μπορεί να δημιουργηθεί λίγο συμπύκνωμα.
!Δεν προτείνεται ηεγκατάσταση του
στεγνωτηρίου σε ντουλάπι. Ηοικιακή
ηλεκτρική συσκευή δεν πρέπει ποτέ να
εγκαθίσταται πίσω από πόρτα που κλείνει
με κλειδί, από συρόμενη πόρτα ήαπό
πόρτα με μεντεσέ στο πλευρό το αντίθετο
της πόρτας του στεγνωτηρίου.
Άδειασμα του νερού
Αν ημηχανή τοποθετηθεί πλησίον ενός σωλήνα
αποστράγγισης μπορεί να εκρεύσει το συμπύκνωμα νερού
απ’ ευθείας χωρίς να χρειαστεί να χρησιμοποιήσετε το
δοχείο συλλογής του νερού. Στην περίπτωση αυτή δεν
απαιτείται πλέον να αδειάζετε το δοχείο συλλογής νερού
μετά από κάθε κύκλο.
Αν το στεγνωτήριο τοποθετηθεί πάνω ήδίπλα σε
πλυντήριο μπορεί να μοιράζεται το ίδιο σύστημα
αποστράγγισης. Αρκεί να αποσυνδέσετε το σωλήνα
που φαίνεται στην εικόνα Aκαι να τον συνδέσετε στην
αποστράγγιση.
Αν το άδειασμα βρίσκεται πιο μακριά από το μήκος του
σωλήνα, για να το φτάσετε μπορείτε να αποκτήσετε και να
συνδέσετε ένα σωλήνα ίδιας διαμέτρου και του αναγκαίου
μήκους.
Για να εγκαταστήσετε το νέο σωλήνα αρκεί να
αντικαταστήσετε τον υπάρχοντα όπως υποδεικνύεται στην
εικόνα Bεισάγοντάς τον στην ίδια θέση.
!Ηαποστράγγιση πρέπει να βρεθεί 1 m χαμηλότερα σε
σχέση με τη βάση του στεγνωτηρίου.
!Αφού εγκαταστήσετε το στεγνωτήριο βεβαιωθείτε ότι ο
σωλήνας αποστράγγισης δεν είναι διπλωμένος κι ούτε
τυλιγμένος.
Εικ. A Εικ. B
Ηλεκτρική σύνδεση
Πριν εισάγετε το βύσμα στην ηλεκτρική
πρίζα ελέγξτε τα ακόλουθα:
• Βεβαιωθείτε ότι τα χέρια είναι στεγνά.
• Ηπρίζα πρέπει να διαθέτει γείωση.
• Ηπρίζα πρέπει να είναι σε θέση να
αντέχει την μέγιστη προβλεπόμενη ισχύ
για τη μηχανή, που αναφέρεται στην
πινακίδα των στοιχείων λειτουργίας
(βλέπε Περιγραφή του στεγνωτηρίου).
• Ητάση τροφοδοσίας πρέπει να κυμαίνεται
στις τιμές που υποδεικνύονται στην
πινακίδα των δεδομένων λειτουργίας (
βλέπε Περιγραφή του στεγνωτηρίου).
• Ηπρίζα πρέπει να είναι συμβατή με
τον τύπο βύσματος του στεγνωτηρίου.
Σε διαφορετική περίπτωση, προβείτε
στην αντικατάσταση της πρίζας ήτου
βύσματος.
!ΜΗ ΧΡΗΣΙΜΟΠΟΙΕΊΤΕ ΠΡΟΕΚΤΆΣΕΙΣ.
!Το στεγνωτήριο δεν μπορεί να
εγκατασταθεί σε χώρους εξωτερικούς,
ακόμη και προφυλαγμένους. Πράγματι,
μπορεί να είναι πολύ επικίνδυνο να
Εγκατάσταση
10 mm
15 mm 15 mm
1
2
H<1m
1
2

19
GR
Μέγιστο μέγεθος φορτίου: 9kg
Αυτό το οικιακό στεγνωτήριο είναι Αυτόματο
Ενεργειακή κατανάλωση πλήρους φορτίου. Edry- kWh 2) 2.85
Ενεργειακή κατανάλωση μερικού φορτίου. Edry½,- kWh 2) 1.56
Κατανάλωση ισχύος: Εκτός λειτουργίας (Po) - Watts 0.14
Κατανάλωση ισχύος: Κατάσταση αναμονής (Pl) - Watts 3.36
Πλήρες φορτίο (Tdry) - λεπτά 261
Μερικό φορτίο (Tdry½) - λεπτά 149
σταθμισμένο (Ct) πλήρες και μερικό φορτίο 3) 81
Πλήρες φορτίο Cdr 81
Μερικό φορτίο Cdry½ 81
Συνθετικά: Ενεργειακή κατανάλωση πλήρους φορτίου. kWh 0.68
Συνθετικά: Πλήρες φορτίο - λεπτά 70
κανονισμό 932/2012.
Συνθετικά: Μερικό φορτίο Μ/Ε
Μέση απόδοση συμπύκνωσης - %
Εκπομπές αερόφερτου ακουστικού θορύβου - dB(A) re 1 pW
70
1) Το "τυπικό πρόγραμμα βαμβακερών" με πλήρες και μερικό φορτίο και το " τυπικό
πρόγραμμα βαμβακερών " μερικού φορτίου είναι τα τυπικά προγράμματα στα οποία
αναφέρονται οι πληροφορίες στην ετικέτα και στην καρτέλα. Τα προγράμματα αυτά
είναι κατάλληλα για πλήρες στέγνωμα (0%) βαμβακερών και είναι τα πιο
αποτελεσματικά προγράμματα με όρους κατανάλωσης ενέργειας. Το μερικό φορτίο
είναι το μισό του πλήρους φορτίου.
2) Ετήσια κατανάλωση βασισμένη σε 160 κύκλους στεγνώματος του τυπικού
προγράμματος βαμβακερών σε πλήρες και μερικό φορτίο, και κατανάλωση των
καταστάσεων λειτουργίας σε χαμηλή ισχύ. Ηπραγματική κατανάλωση ενέργειας
ανά κύκλο θα εξαρτάται από τον τρόπο χρήσης της συσκευής. **Το Τυπικό
Πρόγραμμα Βαμβακερών
3) Μέσο βάρος 3 κύκλων πλήρους φορτίου και 4 κύκλοι μισού φορτίου.
Διάρκεια της κατάστασης αναμονής για σύστημα διαχείρισης
ισχύος - λεπτά
30
Πρόγρ. Σταθμισμένος χρόνος (Tt) πλήρους και μερικού φορτίου-
λεπτά 3)
197
Τάξη απόδοσης συμπύκνωσης σε κλίμακα από το G (ελάχιστη
απόδοση) έως το Α(μέγιστη απόδοση)
B
Αυτό το οικιακό στεγνωτήριο είναι
Συμπυκνωτής
Τάξη ενεργειακής απόδοσης σε κλίμακα από A+++ (χαμηλή
κατανάλωση) έως D (υψηλή κατανάλωση)
A+
Ησταθμισμένη Ετήσια Κατανάλωση Ενέργειας (AEc)* Kwh 1)
340.0
Στοιχεία Προϊόντος - κανονισμό 392/2012
εμπορικό σήμα·
HOTPOINT/ARISTON
μοντέλου
TCD 971 6CY1 (EU)
Διαβαθμισμένη χωρητικότητα πλυμένων βαμβακερών για το
τυπικό πρόγραμμα βαμβακερών σε πλήρες φορτίο - kg
9.0
εκθέσετε την ηλεκτρική αυτή συσκευή στη
βροχή ήσε κακοκαιρία.
!Μετά την εγκατάσταση του στεγνωτηρίου
το ηλεκτρικό καλώδιο και το βύσμα πρέπει
να είναι ευχερή.
!Το ηλεκτρικό καλώδιο δεν πρέπει να
διπλώνει κι ούτε να τσαλακώνει.
!Αν το βύσμα προς αντικατάσταση
είναι ενσωματωμένου τύπου, πρέπει να
το διαθέσετε με τρόπο ασφαλή. ΜΗΝ
το αφήνετε εκεί που θα μπορούσε να
εισαχθεί σε μια πρίζα και να προκαλέσει
ηλεκτροπληξίες.
!Το ηλεκτρικό καλώδιο θα πρέπει να
ελέγχεται περιοδικά. Αν το καλώδιο
τροφοδοσίας είναι χαλασμένο, θα πρέπει να
αντικατασταθεί από τον κατασκευαστή, από
την υπηρεσία του τεχνικής υποστήριξης ή
από άλλο ειδικευμένο επαγγελματία για την
αποσόβηση κινδύνων. (βλέπε Υποστήριξη).
Τα νέα ήτα μακρύτερα ηλεκτρικά καλώδια
παρέχονται από τους εξουσιοδοτημένους
μεταπωλητές με πρόσθετο κόστος.
!Οκατασκευαστής αποποιείται κάθε
ευθύνης όταν δεν τηρούνται οι κανόνες
αυτοί.
!Σε περίπτωση αμφιβολίας σχετικά με
τα παραπάνω, επικοινωνήστε με έναν
ειδικευμένο ηλεκτρολόγο.
Ισοστάθμιση του στεγνωτηρίου
Το στεγνωτήριο πρέπει να εγκατασταθεί
οριζόντια για να λειτουργήσει σωστά.
Αφού εγκαταστήσετε το στεγνωτήριο στην
οριστική θέση, ελέγξτε την ισοστάθμισή του
πρώτα από πλευρά σε πλευρά και στη συνέχεια
από εμπρός με πίσω.
Αν το στεγνωτήριο δεν είναι ισοσταθμισμένο,
ρυθμίστε τα δύο εμπρόσθια ποδαράκια προς τα
επάνω ήτα κάτω, μέχρι να οριζοντιοποιηθεί.
Προκαταρκτικές πληροφορίες
Αφού εγκατασταθεί το στεγνωτήριο, πριν το θέσετε
σε λειτουργία καθαρίστε το εσωτερικό του κάδου και
απομακρύνετε τη βρωμιά που μπορεί να συσσωρευτεί κατά
τη μεταφορά.

20
GR
!Ησυσκευή έχει σχεδιαστεί και
κατασκευαστεί σύμφωνα με τα διεθνή
πρότυπα ασφαλείας. Οι προειδοποιήσεις
αυτές παρέχονται για λόγους ασφαλείας και
πρέπει να τηρούνται με προσοχή.
Γενική ασφάλεια
• Το παρόν στεγνωτήριο μπορεί
να χρησιμοποιείται από άτομα
(συμπεριλαμβανομένων των παιδιών
από 8 ετών και άνω) με μειωμένες
ικανότητες φυσικές, αισθητηριακές ή
νοητικές ήχωρίς εμπειρία και γνώση, αν
επιτηρούνται ήδέχονται οδηγίες σχετικές
με τη χρήση της συσκευής από άτομο
υπεύθυνο για την ασφάλειά τους.
• Το στεγνωτήριο αυτό έχει σχεδιαστεί για
οικιακή και όχι για επαγγελματική χρήση.
• Μην αγγίζετε τη συσκευή όταν είστε
ξυπόλητοι ήέχετε βρεγμένα χέρια ήπόδια.
• Όταν βγάζετε τη συσκευή από την πρίζα,
τραβάτε το ρευματολήπτη (φις) και όχι το
καλώδιο.
• Μετά τη χρήση, απενεργοποιήστε το
στεγνωτήριο και βγάλτε το από την
πρίζα. Κρατάτε την πόρτα κλειστή για
να βεβαιωθείτε ότι τα παιδιά δεν θα τη
χρησιμοποιούν σαν παιχνίδι.
• Τα παιδιά δεν πρέπει να μένουν χωρίς
επίβλεψη, ώστε να διασφαλίζεται ότι δεν
παίζουν με το στεγνωτήριο.
• Καθαρισμός και συντήρηση δεν πρέπει να
εκτελούνται από παιδιά χωρίς επιτήρηση.
• Τα παιδιά ηλικίας μικρότερης των 3 ετών
θα πρέπει να κρατιούνται σε απόσταση
από το στεγνωτήριο εκτός κι αν
επιτηρούνται συνεχώς.
• Ησυσκευή πρέπει να εγκαθίσταται σωστά
και να αερίζεται επαρκώς. Ηείσοδος αέρα
στη μπροστινή όψη του στεγνωτηρίου
δεν πρέπει να φράσσεται ποτέ. (βλ.
Εγκατάσταση).
• Ποτέ μην χρησιμοποιείτε το στεγνωτήριο
επάνω σε χαλιά όπου το ύψος του πέλους
μπορεί να εμποδίζει την είσοδο του αέρα
στο στεγνωτήριο από τη βάση.
• Ελέγξτε αν το στεγνωτήριο είναι άδειο
πριν το γεμίσετε.
• Το πίσω μέρος του στεγνωτηρίου
μπορεί να ζεσταθεί πολύ. Ποτέ μην το
αγγίζετε την ώρα που λειτουργεί.
• Μη χρησιμοποιείτε το στεγνωτήριο
εάν το φίλτρο, οπεριέκτης νερού και ο
συμπυκνωτής δεν έχουν στερεωθεί καλά
στη θέση τους (βλ. Συντήρηση).
• Μην υπερφορτώνετε το στεγνωτήριο (βλ.
Πλύσιμο ρούχων) για μέγιστα φορτία.
• Μην βάζετε στο στεγνωτήριο πλυμένα
ρούχα που στάζουν.
• Ελέγξτε προσεκτικά όλες τις οδηγίες
στις ετικέτες των ρούχων (βλ. Πλύσιμο
ρούχων).
• Μην στεγνώνετε μεγάλα, πολύ ογκώδη
είδη.
• Μην στεγνώνετε ακρυλικά υφάσματα σε
υψηλές θερμοκρασίες.
• Μην απενεργοποιείτε το στεγνωτήριο ενώ
περιέχει ακόμη ζεστά ρούχα.
• Καθαρίζετε το φίλτρο μετά από κάθε
χρήση (βλ. Συντήρηση).
• Εκκενώνετε τον περιέκτη νερού μετά από
κάθε χρήση (βλ. Συντήρηση).
• Καθαρίζετε τη αντλία θερμότητας
ανά τακτά χρονικά διαστήματα (βλ.
Συντήρηση).
• Μην αφήνετε να συγκεντρώνεται χνούδι
γύρω από το στεγνωτήριο.
• Ποτέ μην ανεβαίνετε επάνω στο
στεγνωτήριο, μπορεί να προκαλέστε βλάβη.
• Πάντα να τηρείτε τα ηλεκτρικά πρότυπα
και τις προδιαγραφές (βλ. Εγκατάσταση).
• Πάντα να αγοράζετε γνήσια ανταλλακτικά
και αξεσουάρ (βλ. Τεχνική υποστήριξη).
Για να ελαχιστοποιηθεί οκίνδυνος
πυρκαγιάς στο στεγνωτήριο σας,
θα πρέπει να προσέχετε τα εξής:
• Βάζετε στο στεγνωτήριο ρούχα μόνο αν
έχουν πλυθεί με απορρυπαντικό και νερό,
έχουν ξεπλυθεί και στυφτεί. Υπάρχει
κίνδυνος πυρκαγιάς αν στεγνώνετε ρούχα
που ΔΕΝ έχουν πλυθεί με νερό.
• Μην στεγνώνετε ρούχα που έχουν
υποβληθεί σε χημικά προϊόντα.
• Μη στεγνώνετε ρούχα που έχουν
λερωθεί ήεμποτιστεί με ελαιόλαδο ή
λάδι μαγειρικής, γιατί υπάρχει κίνδυνος
πυρκαγιάς. Τα λαδωμένα αντικείμενα
μπορεί να αναφλεγούν αυτόματα,
ιδιαίτερα όταν εκτίθενται σε πηγές
θερμότητας όπως το στεγνωτήριο. Τα
αντικείμενα ζεσταίνονται και προκαλούν
μια αντίδραση οξείδωσης με το λάδι,
ηοποία προκαλεί θερμότητα. Αν η
θερμότητα δεν μπορεί να διαφύγει, τα
αντικείμενα ενδέχεται να θερμανθούν
σε επίπεδο πρόκλησης πυρκαγιάς.
Ηστοίβαξη ήηφύλαξη λαδωμένων
αντικειμένων μπορεί να εμποδίσει τη
Προειδοποιήσεις