Hotpoint Ariston Aqualtis AQ9D 49 X User manual

EN
1
English,1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
Technical data
Description of the machine, 4-5
Touch control panel
Running a wash c cle, 6
Wash c cles and options, 7
Table of wash cycles
Wash options
Detergents and laundr , 8
Detergent
Preparing the laundry
Washing recommendations
Precautions and advice, 9
General safety
Load balancing system
Disposal
pening the porthole door manually
Care and maintenance, 10
Cutting off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser drawer
Caring for your appliance drum
Cleaning the pump
Checking the water inlet hose
Trouble shooting, 11
Assistance, 12
EN
WASHING MACHINE
AQUALTIS
AQ9D 49 X
Instructions for
installation and use
Français,13
F

EN
2
Installation
 This instruction manual should be kept in a safe place
for future reference. If the washing machine is sold,
given away or moved, please ensure the manual is kept
with the machine, so that the new owner may benefit
from the advice contained within it.
 Read these instructions carefully: they contain vital
information relating to the safe installation and operation
of the appliance.
 Inside the pack containing this manual, you will also
find the guarantee and all the details necessary for
installation.
Unpacking and levelling
Unpacking
1. nce you have removed all the packaging from the
washing machine, make sure it has not been damaged
during transportation.
If it has been damaged, contact the retailer and do not
proceed any further with the installation process.
2. Remove the 4
protective screws (used
during transportation) and
the corresponding spacer,
located on the rear part of
the appliance (see figure).
3. Close off the holes using the plastic plugs supplied in
the pack.
4. Keep all the parts in a safe place; they will be needed
again if the washing machine is moved to another
location, to prevent the inside of the appliance being
damaged.
 Packaging materials should not be used as toys for
children.
Levelling
1. Place the washing machine on a flat sturdy floor,
without resting it up against walls or cabinets.
2. If the floor is uneven,
the front feet of the
machine may be adjusted
until it reaches a horizontal
position (the angle of
inclination must not
exceed 2 degrees).
 If the appliance is levelled correctly, it will be more
stable and much less likely to cause vibrations and noise
while it is operating, particularly during the spin cycle.
 If it is placed on carpet or a rug, adjust the feet in such
a way as to allow a sufficient ventilation space
underneath the washing machine.
Connecting the electricit and water
supplies
Connecting the water inlet hose
 Before connecting the inlet hose to the water supply,
run the water until it is perfectly clear.
1. Connect the inlet hose
to the machine by
screwing it onto the cold
water inlet of the
appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
2. Connect the inlet hose
by screwing it to a cold
water tab using a 3/4 gas
threaded connection (see
figure).
3. Make sure that the hose is not folded over or bent.
 The water pressure at the tap must fall within the
values indicated in the Technical data table (see next
page).
 If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
 Never use second-hand or old inlet hoses; use the
products supplied with the machine.

EN
3
Technical data
Model AQ9D 49 X
Dimensions
width 59,5 cm
height 85 cm
depth 64,5 cm
Capacit from 1 to 9 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed up to 1400 rotations per minute
Energ rated
programmes
according to
regulation
EN 60456
programme ; temperature 60°C;
using a load of 9 kg.
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2006/95/EC (Low Voltage)
- 2002/96/EC
65 - 100 cm
Connecting the drain hose
Connect the drain hose to
drain duct piping or a wall
drain located between 65
and 100 cm above the
floor, making sure it is not
bent at all.
Alternatively, rest the drain
hose on the side of a
washbasin or bathtub,
fastening the duct
supplied to the tap (see
figure).
The free end of the hose
should not be underwater.
 We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150
cm in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
 the socket is earthed and complies with all applicable
laws;
 the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
 the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
 the socket is compatible with the plug of the
appliance. If this is not the case, have the socket or
the plug replaced.
 The machine must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain, storms and other weather
conditions.
 The mains socket must remain within easy reach after
the washing machine has been installed.
 Do not use extension cords or multiple sockets.
 The cable should not be bent or compressed.
 The power supply cable and plug must only be
replaced by authorised technicians.
Warning! The company shall not be held responsible in
the event that these regulations are not respected.

EN
4
CONTROL
PANEL
1
2
20
Description of the machine
PORTHOLE DOOR
Always use the handle to
open the porthole door (see
figure).
DETERGENT DISPENSER DRAWER
The detergent dispenser
drawer is located inside the
machine and can be
accessed by opening the
door.
For more information on
detergent measures, please
refer to the chapter entitled
Detergents and laundry.
Note: stick the label showing
the wash cycle descriptions and options on the front of
the detergent dispenser drawer. ou will find the sticker
in the pack containing this manual.
1. pre-wash compartment:
use powder detergent.
2. main wash compartment:
use powder or liquid
detergent. If using the latter
type of detergent, we
recommend it is poured into
the drawer immediately
before you start the washing
machine.
washing additives compartment: for fabric softener or
liquid additives. We recommend that the maximum level
indicated by the grille is not exceeded, and that
concentrated fabric softeners are diluted.
TOUCH CONTROL PANEL
To adjust the settings, gently
press the icon inside the
sensitive (touch control) area
as illustrated in the figure.
Standb mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after a few minutes if no activity
is detected. Press the N- FF button briefly and wait
for the machine to start up again.
PORTHOLE DOOR
PORTHOLE DOOR
HANDLE
ADJUSTABLE FEET
KICK STRIP

EN
5
WASH CYCLE
SELECTOR knob
Button withON/OFF
indicator light
Touch control panel
Button with ON/OFF indicator light: press this briefly to
switch the machine on or off. The green indicator light
indicates that the machine is switched on. To switch off the
washing machine during the wash cycle, press and hold the
button for approximately 3 seconds; if the button is
pressed briefly or accidentally the machine will not switch
off. If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR knob: may be turned in either
direction. To select the most suitable wash cycle, please refer
to the Table of wash cycles.
The knob will not move during the wash cycle.
M1-M2-M3 buttons: press and hold one of the buttons to
store a cycle with your own set preferences in the memory of
the machine. To recall a previously-stored cycle, press the
corresponding button.
TEMPERATURE button: press to modify or exclude the
temperature setting; the value selected will appear on the
display above (see Running a wash cycle).
SPIN CYCLE button: press to modify or exclude the spin
cycle; the value selected will appear on the display above (see
Running a wash cycle).
DELAYED START button: press to set a delayed start
for the selected wash cycle; the set delay time will appear on
the display above (see Running a wash cycle).
OPTION buttons: press to select the available options. The
indicator light corresponding to the selected option will remain
lit (see Running a wash cycle).
WASH CYCLE PHASE icons: these illuminate to indicate the
progress of the wash cycle (Wash  Rinse  Spin 
Drain ). The text lights up when the cycle is complete.
START/PAUSE button with indicator light: when the green
indicator light flashes slowly, press the button to start a wash
cycle. nce the cycle has begun the indicator light will remain
lit in a fixed manner. To pause the wash cycle, press the button
again; the indicator light will flash in an orange colour. If the
Door locked indicator light is switched off, the door may
be opened. To start the wash cycle from the point at which it
was interrupted, press the button again.
DOOR LOCKED indicator light: indicates that the
porthole door is locked. To open the door, pause the wash
cycle (see Running a wash cycle).
CONTROL PANEL LOCK button with indicator light: to
activate or deactivate the control panel lock, press and hold
the button for approximately 2 seconds. when the indicator
light is illuminated, the control panel is locked. This means it is
possible to prevent wash cycles from being modified
accidentally, especially where there are children in the home.
ECO indicator light: the icon lights up when, after altering
the washing parameters, an energy saving of at least 10% is
made. Furthermore, before the machine enters Standby
mode, the icon will light up for a few seconds; when the
machine is switched off the estimated energy saving will be
around the 80% mark.
CHANGE LANGUAGE
The first time the machine is switched on, the first
language will flash on the display. The " ", "OK" and "V"
symbols will appear on the display, in line with the 3 buttons
on the right-hand side. The languages change automatically
every 3"; alternatively, they can be changed by pressing the
buttons next to the " " and "V" symbols. Use the "OK" button
to confirm the language, which will be set after 2". If no
buttons are pressed, the automatic language change will
begin again after 30".
The language may only be changed while the machine is
switched off.
Press and hold the temperature +spin +delayed start
buttons for 5''; a short beep sounds and the set language
flashes on the display. Press the buttons next to the " " and
"V" symbols to change the language. Use the button next to
the "OK" symbol to confirm the language, which will be set
after 2". If no buttons are pressed, the language set previously
will be displayed after 30".
Switch on the machine.
TEMPERATURE
button
OPTION
buttons
SPIN
button
DISPLAY
M1
ECO
indicator light
DELAYED START
button
START/PAUSEbutton
with indicator light
DOOR LOCKED indicator light
WASH
CYCLE
PHASE
icons
CONTROL PANEL
LOCK button with
indicator light
M2
M3