Hotpoint Aqualtis AQCF 852 BI User manual

1
GB
English,1
Contents
Important Information, 2-3
Installation, 4
Where to put your dryer
Ventilation
Electrical connection
Before you start using your dryer
Dryer Description, 5
Open the door
The Features
Control Panel
The Display,
Start and Programmes, 7-12
Choosing a Programme
Special Programmes
Table of Programmes
The Controls
Laundry, 13-14
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 15
eneral safety
Disposal
Save energy and respect the
Environment
Maintenance and Care, 1
Switching off the electricity
Clean the filter after each cycle
Check the drum after each cycle
Empty the Water Container after each cycle
Cleaning the Condenser
Cleaning the dryer
Troubleshooting, 17
Service, 18
Spare parts
GB
TUMBLE DRYER
AQUALTIS
AQCF 852 BI
AQCF 852 BU
Instruction booklet
 This symbol reminds you to read this instruction manual.
 Keep this instruction booklet on hand in order to refer to it
when necessary. Take it with you when you move, and, should
you sell this appliance or pass it on to another party, make sure
that this booklet is supplied along with the dryer so that the new
owner may be informed about warnings and suggestions on how
the dryer works.
 Read these instructions carefully; the following pages contain
important information on installation and suggestions on how the
appliance works.

2
GB
Important Information
For your Condenser dryer to operate efficiently,
you must follow the regular maintenance
schedule shown below:
Fluff Filter  You MUST Clean the fluff filter
after every drying cycle.
Step 1
Open the door of your dryer.
Step 2
Pull out the filter (using the two
finger grips).
Step 3
Open the filter by releasing the
clip.
Step 4
Clean any fluff deposits from the
inside surface of the filter mesh.
Step 5
Refit the filter  Never run the
dryer without a filter.
Failure to clean the filter after every drying
cycle will affect the drying performance of your
machine  It will take longer to dry and as a
result will use more electricity during drying.
Water Container  You must empty the water
container after every drying cycle.
Step 1
Pull the water container
towards you and remove it fully
from the dryer.
Step 2
Empty the Water from the
Container.
Step 3
Refit the Water Container
ensuring that it is pushed fully
back into position...
Failure to empty the Water Container will result in:
- The machine will stop heating (so the load
may be wet at the end of the cycle).
- The Empty Water light will flash to tell you
that the Container is full.
 The water bottle/clean
filter light comes on when
you select a programme to
remind you to make sure
that the water bottle is
empty and that the filter is
clean before starting a new
cycle
Priming the Water Collection System
When your dryer is new, the Water Container will
not collect Water until the system is primed, this
will take 1 or 2 drying cycles. Once primed it
will collect Water during every cycle.
2

3
GB
Condenser unit - You must clean the fluff from
the condenser every month!
Step 1
Open the Condenser Cover
- hold the handle and pull
towards you.
Step 2
Remove the condenser by
rotating the 3 clips then pulling
the condenser towards you.
(There may be some water in the
tubes this is normal).
Step 3
Flush the condenser, from the
rear with water, to remove any
fluff deposits.
Step 4
Refit the condenser unit - ensure
that the unit is pushed in fully, all
3 clips are resecured and the
positioning arrows on the front of
the condenser are pointing
upwards.
Failure to clean the condenser could cause
premature failure of your dryer!

4
GB
Installation
Where to put your dryer
 Place your dryer at a distance
from gas ranges, stoves,
heaters, or cooktops because
flames can damage the
appliance.
If you are going to install the
appliance under a work counter,
be sure to leave a 10 mm
space between the top and any
other objects on or above the
machine and a 15 mm space
between the sides and lateral
furnishings or walls. This is to ensure proper air circulation.
Ventilation
 When the dryer is in use, there has to be adequate
ventilation. Make sure you put your dryer in an environment
that is not damp and has proper air circulation throughout.
Airflow around the dryer is essential to condense the water
produced during the washing, the dryer will not operate
efficiently in an enclosed space or cupboard.
 If using the dryer in a small or cold room some
condensation will be experienced.
 We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed behind a
lockable door, a sliding door or a door with a hinge on the
opposite side to that of the dryer door.
Water Drain
If the machine is positioned close to a drain it is possible to
drain the condensed water directly without using the
waterbottle. In which case it is no longer necessary to
empty the water bottle at the end of each cycle.If the Dryer
is positioned above or close to a Washing Machine the
same drainage can be used. Just unlink the tube indicated
in figure A and connect it to the drainage.
If the drainage is further away than the length of the tube it
is possible to buy and connect a tube of the same diameter
and the necessary length in order to reach the drainage.
To install the new tube just substitute the existing one as
indicated in figure B inserting it in the same place.
 The drain tube has to be below 1 m from the bottom
of the Dryer.
 Once the Dryer has been installed please assure that
the drain tube is not bent or contorted.
10 mm
15 mm 15 mm
Electrical connection
Make sure of the following before you insert the plug into
the electrical socket:
 Ensure your Hands are dry.
 The socket must be grounded.
 The socket must be able to sustain the machines maximum
power, which is indicated on the rating label (see Dryer Description).
 Power voltage must be within the values indicated on the
rating label (see Dryer Description).
 The socket must be compatible with the dryers plug.
Should this not be the case, replace the plug or the socket.
 Do not use extension cords.
 The dryer must not be installed outdoors, even if the space is
sheltered. It can be very dangerous if exposed to rain or storms.
 Once installed, the dryers electrical wire and plug must
be within reach.
 The power cord must not be bent or squashed.
 The power cord is supplied fitted with a BS1363 plug
and with a 13 amp BS1362 fuse. If it is necessary to fit a
replacement fuse, it must be a 13 Amp ASTA approved to
BS1362 type. WARNIN : The plug must not be used
without a fuse cover.
If a replacement fuse holder/cover is required, it must be of the
same colour coding or wording as shown on the base of the plug.
Replacements are available from authorised dealers.
Changing the plug
The wires in the power cord are coloured in accordance
with the following.
 If the plug being replaced is a non-rewirable type, then the
cut-off plug must be disposed of safely. DO NOT leave it where
it can be inserted into a socket and create a shock hazard.
 The power cord should be checked periodically and replaced
by a cord specially prepared for this dryer and fitted only by
authorized technicians (see Service). New or longer power
cords are supplied at an extra charge by authorized dealers.
 The manufacturer denies any responsibility should any of
these rules not be followed.
 If in doubt about any of the above consult a ualified electrician.
Before you start using your dryer
Once youve installed your dryer and before you use it,
clean the inside of the drum to remove any dust that could
have accumulated during transportation.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
Moulded plug
Green and Yellow (Earth)
wire to terminal marked
E, symbol x, or coloured
green and yellow.
Blue (Neutral) wire to
terminal marked N or
coloured black.
13A ASTA approved fuse
to BS 1362.
Brown (live) wire to teminal
marked L or coloured
red.
2
H<1m
2
Fig. A Fig. B

5
GB
To open door
Option Buttons and Lights
On/Off Button & Light Display Panel Child Lock
Button & Light
Start/Pause Button &
Light
Clean
Condenser
Light
Programme
Progress Light
Programme Knob Empty Water
Clean Filter
Light
Dryer Description
Control Panel
Indicator
The On/Off button/ light , if the dryer is running and this
button is pressed the dryer is turned off. The light signals
that your dryer is in use or ready to select a programme.
The Programmes knob sets the programme: rotate until
the indicator is pointing to the programme you want to
select (see Start and Programmes).
The Option buttons/ lights select available options for your
selected programme. The lights indicate that the option
has been selected (see Start and Programmes).
The Display Panel has three sections: Sensor Dry = Drying
level, Timed dry = Drying time and Time to End / Delay start
each with a corresponding selection button (see The Display).
START/PAUSE button with indicator light : when the
green indicator light flashes slowly, press the button to
start the programme. When the cycle has started, the
indicator light is illuminated in a fixed manner. To pause the
programme, press the button again; the indicator light will
turn orange and begin to flash again.
To restart the programme from the point at which it was
interrupted, press the button again (see Start and
Programmes).
The Programme Progress Lights indicate each state of the
programme by turning on as appropriate.(see Start and
Programmes).
The Empty Water indicator H2O signals that the water
container should be emptied. The light will take a few
seconds to go out after replacing the empty water
container; the dryer must be running for this to happen (see
The Controls).
Note: if the water bottle is full the display shows H2O
and the indicator flashes, the heat is turned off and your
clothes will not dry.
The Empty Water Clean Filter Light gives a reminder
before every programme, that its essential to clean the
filter and empty the water container every time the dryer is
used (see Maintenance and Care).
The Clean Condenser Light gives a reminder, that its
essential to clean the condenser at regular intervals (see
Maintenance and Care).
The Child Lock button/light Press and hold this button
after selecting your programme and any options. This
prevents the programme settings from being changed.
When the light is lit the other buttons and programme knob
are disabled. Hold the button to cancel and the light will go
out.
ECO Light - this light is illuminated as you select options
that use less energy (see the controls).
The Features
Pull on handle
Condenser unit
(cover open)
Water
container
Rating
Plate
Condenser
cover handle
(Pull to open)
Filter
Air Intake
Grille
Model &
Serial
Numbers
ECO Light

GB
The Display
The Display has three sections each with its corresponding button.
Sensor Dry
After selecting a programme that has a Sensor Dry Option, press and release the button until the required
dryness sensing level is displayed. If the sensing option is not available the display will flash and the buzzer
beeps three times.
 Some drying programmes are not compatible with all 5 sensor drying levels.
Dryness levels available
Damp: Retains maximum moisture in the garments, which is ideal for difficult to iron fabrics such as linen.
Iron: Retains moisture in your clothes to help make ironing easier.
Hanger: Dries you clothes ready to be hanged for final drying; Use for items that can simply be
hung up to finish drying.
Cupboard: Dries your items to put away.
Ready to wear: Dries clothes so that they are immediately ready to wear.
Timed Dry
After selecting a Programme that has a Timed Dry Option, press the Timed Button to insert a drying
time. The display will reduce the selected time each time you press and release this button (see Start
and Programmes). Each press decreases the set time 180, 160, 120, 90, 60, 30, 20 and then repeats.
If the Timed Dry option is not available the display will flash and the buzzer beeps three times.The
selected time remains displayed after the programme starts and cannot be changed after the Start/
Pause Button , is pressed.
You can either choose a sensor dry level or a drying time.
Delay Start
After selecting a Programme that has a Delay Start Option a delay start time can be selected.
Each press of the Delay start button advances the delay setting in 1 hour increments from 1h to
24h then OFF and then after five seconds cancels the delay.
For delays of 10 hours or more the display counts down the time in hours until 10 hours, then the display
shows 9:59 and then counts down in minutes. For delays of 9 hours or less the display shows hours and
minutes and then counts down in minutes for all of the delay.
After the Start/Pause Button is pressed the time cannot be changed.
When the delay period finished the symbol is off and the Time to End is displayed.
If you have chosen a timed drying the display during programming will show the drying time only in
the timed drying display in the middle. After having pressed start the machine will turn the time
display on and visualize the countdown of the programme time.
Time to End
If the delay icon is off the time displayed is the Time to End of the programme running.
When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.
When an Automatic programme is selected the time displayed is an estimate of the time remaining.
When the programme is selected the display shows the time required to dry a full load, after around
10 minutes the controller calculates a better estimate of the cycle time.
The time to end is displayed in hours and minutes and counts down each minute.
The colon between the hours and minutes display flashes to show that the time is counting down.
The Display also shows if there is a problem with your dryer, if this occurs the display will show F
followed by a fault code number, the four option lights and the pause light will also flash Orange
(see Troubleshooting).

7
GB
Start and Programmes
Choosing a Programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see Laundry).
3. Open the door and make sure the filter is clean and in
place and the water container is empty and in place (see
Maintenance).
4. Load the machine and make sure that the items are not
in the way of the door seal. Close the door.
5. If the ON/Off light is not lit; press the On/Off Button .
6. Select the Programmes selection that corresponds with
fabric being dried by checking the Programmes table (see
Programmes) as well as the indications for each type of
fabric (see Laundry).
7. Where available, choose Sensor Dry or Timed Dry
option pressing and releasing the corresponding button until the
desired level or time is read.
 See programmes table, for more details.
8. Set a delay time and other options as necessary (see The
Display).
9. If you wish the buzzer to sound at the end of the
programme, press the ALARM button .
10. Press the START button to begin. The display will
show the estimated time to end.
Special Programmes
Easy Iron Programme
Easy Iron is a short 10 minute programme (8 minutes of heat followed by a 2 minutes cool tumble period) which fluffs the
fibres of clothing that has been left in the same position/location for an extended period of time. The cycle relaxes the fibres
and makes them easier to iron and fold.
 Easy Iron is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than maximum capacity. These numbers refer to dry weight:
Fabric: Max
Cotton and Cotton mix 2.5 kg
Synthetics 2
Denim 2
2. Unload the dryer immediately after the end of the drying cycle, hang, fold or iron the articles and put them away in the
closet. Should this not be possible, repeat the cycle.
The Easy Iron effect varies from one fabric to the next. It works very well on traditional fabrics like Cotton or Cotton mix, and
less well on acrylic fibres and on materials such as Tencel.®
Wool Programme
 This is a programme for tumble dryer safe garments marked with the symbol .
 It can be used for load sizes up to 1 kg (approximately 3 sweaters).
 We recommend that garments are turned inside out before drying.
 This programme will take about 60 minutes, but may take longer depending on the size and density of the load and the
spin speed used in your washer.
 Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly
damp. Allow these to dry naturally as over-drying could damage garments.
 Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.
 This program is not suitable for Acrylic garments.
Jeans
 This is a programme for Jeans made from Denim Cotton. Before drying your Jeans turn the front pockets inside out.
 It can be used for load sizes up to 3 kg (approximately 4 pairs).
 It can also be used on other garments made from same material such as jackets.
 This programme will take about 85 minutes, but may take longer depending on the size of the load and the spin speed
used in your washer.
 Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try
turning the jeans inside out and running the programme again for a short period.
 Use this cycle only for a 100% cotton load, do not mix dark and light coloured items. Do not use this cycle for garments
with embroidery and accessories (pins,...), turn the pockets insideout
 We do not recommend that you use this programme if your jeans have elastic waste bands or embroidery.
During the drying programme, you can check on your
laundry and take out the items that are dry while the others
continue drying. When you close the door again, press
START in order to resume drying.
11. During the last few minutes of Drying Programmes
before the programme is completed, the final COOL
TUMBLE phase is entered (fabrics are cooled), this
phase should always be allowed to complete.
12. The buzzer (if option selected) will warn you when the
programme is complete and the display shows END.
Open the door, take your laundry out, clean the filter and
replace it. Empty the water container and replace it (see
Maintenance).
If the Post care option has been selected and you do
not take the clothes out immediately the clothes will tumble
occasionally for 10 hours or until you open the door.
13. Switch dryer off using the On/Off button.
Standby mode
This tumble dryer, in compliance with new energy saving
regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the On-Off button briefly and wait for the
machine to start up again.

8
GB
Special Programmes
Shirts - High Heat
 This is a programme for Shirts made from Cotton.
 It can be used for load sizes up to 3 kg (approximately 10 shirts).
 This programme will take about 80 minutes, but may take longer depending on the size of the load and the spin speed
used in your washer.
 Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try
turning the shirts inside out and running the programme again for a short period.
Shirts - Low Heat
 This is a programme for Shirts made from synthetic materials or a mixture of natural and synthetics materials such as
Polyester and Cotton.
 It can be used for load sizes up to 3 kg (approximately 14 shirts).
 This programme will take about 65 minutes, but may take longer depending on the size of the load and the spin speed
used in your washer.
 Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try
turning the shirts inside out and running the programme again for a short period.
Silk
 This is a programme for drying your Delicate Silk.
 It can be used for load sizes up to 0.5 kg.
 This programme will take about 110 minutes, but may take longer depending on the size and density of the load and the
spin speed used in your washer.
 Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly
damp. If this is found try removing the load and open them out then run the programme again for a short period.
 Only for garments labelled suitable for tumble drying.
Duvet programmes
 Take care with these programme do not dry any items that are damaged which could result in the filling blocking the filter
and air path resulting in a fire hazard.
 Must only be used on Single size duvets not suitable for double or king size items.
 Loads dried using this programme are usually ready to use, but may be slightly damp in places. If this is found try removing
the load and open them out and shake then run the programme again for a short period.
 Also suitable for down filled jackets.
Duvet Cotton
 This is a programme for drying your Cotton Duvets. With Cotton outer cover and down filling.
 This programme will take about 120 minutes, but may take longer depending on the size and density of the load
and the spin speed used in your washer.
 Only for garments labelled suitable for tumble drying.
Duvet Synthetic
 This is a programme for drying your Synthetic Duvets, with synthetic filling.
 This programme will take about 115 minutes, but may take longer depending on the size and density of the load
and the spin speed used in your washer.
 Only for garments labelled suitable for tumble drying.
Baby
 This is a programme for drying your babys small delicate items of clothing and bedding.
 Use it for items made from Cotton and Chenille, do not dry items such as bibs and nappy pants with plastic coverings.
 It can be used for load sizes up to 2 kg.
 This programme will take about 120 minutes, but may take longer depending on the size and density of the load and the
spin speed used in your washer.
 Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly
damp. If this is found try turning them inside out and running the programme again for a short period.
Lingerie
 This is a programme for drying your very delicate lingerie including silk.
 It can be used for load sizes Max 1 kg, close bras hooks, buttons or zip before drying.
 This programme will take about 90 minutes, but may take longer depending on the size and density of the load and the
spin speed used in your washer.
 Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly
damp. If this is found try turning them inside out and running the programme again for a short period.

9
Delicates
 This is a programme for drying your Delicate Clothes i.e. Acrylics.
 It can be used for load sizes up to 2.0 kg.
 This programme will take about 120 minutes, but may take longer depending on the size and density of the load and the
spin speed used in your washer.
 Loads dried using this programme are usually ready to use, but on some garments may be slightly damp. If this is found
try removing the load and open them out or turn inside out then run the programme again for a short period.
Bed & Bath
 This is a programme for Cotton Towels and sheets.
 It can be used for load sizes up to 8 kg.
 This programme will take about 150 minutes, but may take longer depending on the size of the load and the spin speed
used in your washer.
 Loads dried using this programme are usually ready to use; the edges or seams may be slightly damp especially on large
items. If this is found try opening them out and running the programme again for a short period.
Refresh
Airing is not a drying programme and should not be used for wet articles of clothing.
 If can be used on any load size up to 8 kg, but is more effective on smaller loads.
20-minute programme that airs your clothes with cool air. Use also to cool warm clothes.

10
GB
Program-
me What it does How to set it Notes / Options available
Easy Iron
Brief programme (approximately
10 minutes) that softens fibres of
clothing that is ready for ironing.
1. Position the PRO RAMME knob on .
2. Select Alarm Option if required.
3. Press the Start Button .
 This is not a drying programme (see
previous page).
Options available
Alarm .
Refresh
20 min cool programme to air
your clothes
1. Position the PRO RAMME knob on .
2. Select Alarm Option if required.
3. Press the Start Button . Alarm .
Cottons
Cotton -
High Heat
Dries: your Cotton clothes on
High heat.
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry or Timed Dry (see
next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Mini Load .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry , Ready to Wear .
Cotton -
Low Heat
Dries: your Cotton clothes on
Low heat.
N.B: Max. load 6 kg
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry or Timed Dry (see
next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Mini Load .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry .
Shirts
Shirts -
High Heat
Dries your shirts on a high heat.
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry or Timed Dry (see
next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Mini Load .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry .
Shirts -
Low Heat
Dries your shirt on low heat.
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry or Timed Dry (see
next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Mini Load .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry .
Jeans
Dries denim clothes on a high
heat.
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry (see next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry , Ready to Wear .
(We suggest to use only Ready to Wear).
Synthetics
Dries: your synthetics clothes on
High heat.
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry or Timed Dry (see
next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Mini Load .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry .
Bed & Bath
Dries your Towels and bedding
on High heat.
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry (see next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry . (We suggest to use
only Cupboard dry).
Duvet
Cotton
Dries your Duvet on a Low heat.
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry (see next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry . (We suggest to use
only Cupboard dry).
Duvet
Synthetic
Dries you Duvet bedding on Low
Heat.
1. Position the PRO RAMME knob on .
2. Choose Sensor Dry (see next page).
3. Select any Options if required.
4. Press the Start Button .
Alarm . Delay Start .
Pre care . Post care .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger dry
Cupboard dry . (We suggest to use
only Cupboard dry).
Programmes Table
 If the On/Off light is not lit; Press the On/Off Button and then select programme.