Hotpoint NVLR223EG User instructions

NVLR223EG – Hotpoint 5.8 Cu. Ft. Extra-Large Capacity Electric Dryer
Dryer Dimensions (in inches)
Exhaust Options:
4-way via rear, right, left and bottom.
Circuit Requirements:
An individual, properly-grounded branch circuit, protected by a
30-amp circuit breaker or a time-delay fuse, is required.
Electric Dryer Rating:
240V, 5600W, 60Hz, 24 Amp
208V, 4400W, 60Hz, 22 Amp
Installation Information: For complete information, see installation
instructions packed with product for current dimensional data.
*24-1/2” from the edge of the side panel to the front.
25-1/2” from front to edge of end caps.
Specification Revised 12/06
470150
Listed by
Underwriters
Laboratories
36
25-1/2
42
54-1/2
Side View
27
Rear View
36 42
27
23-1/2
2-1/2
25-1/2*
Side View Rear View
5-1/4
25-3/4
23-1/2
11-1/2
HTP Washer/Dryers XLC QSart
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a
label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side
3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of
60 sq. in. of open area equally distributed. If this closet contains both a washer and a
dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes,
with the National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides
3" rear

Dryer exhausting information
For complete information see installation instructions packed with dryer.
Important note:
5.8 cu. ft., 6.0 cu. ft. and 7.0 cu. ft. dryers do not require additional parts to convert to bottom
or side venting. Unitized models do not require a kit for side venting.
Ducting materials
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If “all rigid
metal” duct cannot be used, then “flexible all metal” venting can be used, but it will reduce the maximum
recommended duct length. The following kit or parts are available from your local service organization.
Kit WX8X75 – 7' aluminum duct and 4' hood, short tail.
(OR individual parts):
WX8X65 7' aluminum flex duct only
WX8X58 4' clamps (2)
WX8X67 4' exhaust hood
See installation instructions for complete information.
Exhaust length calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of
dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is shown in the
table. The maximum lengths for flexible ducts are less than for rigid duct.
See table in installation instructions. A turn of 45° or less may be ignored. Two 45° turns within the duct
length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large amounts of moisture
and lint from being blown into the room. Gas dryers or any dryer located in a closet must be exhausted to
the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor
(crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause
damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the
combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The
wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed
down. Other terminations, such as louvered wall boxes, are acceptable provided they are equivalent to a
4" opening dampered wall cap.
NVLR223EG – Hotpoint 5.8 Cu. Ft. Extra-Large Capacity Electric Dryer
Dryer Exhausting Information – Use Metal Duct Only
Vertical and Horizontal Ducting
Specification Revised 12/06
470150
Listed by
Underwriters
Laboratories
A
A
B
2-1/2
4
GE Dryer Vent
A
B
2-1/2
4
GE Dryer Vent
Best Performance
Maximum Length of 4" Dia.
Rigid Metal Duct
Maximum Length of 4" Dia.
Flexible Metal Duct
Exhaust Hood Type Exhaust Hood Type
Domestic
Dryer Models
Number
of
90°
Turns
A
4" Opening
B
2-1/2"
Opening
A
4" Opening
B
2-1/2"
Opening
7.0, 6.0 and 5.8
Capacity Models
all Electric Dryers
0
1
2
3
4
90 ft.
60 ft.
45 ft.
35 ft.
25 ft.
65 ft.
45 ft.
35 ft.
25 ft.
15 ft.
55 ft.
40 ft.
30 ft.
20 ft.
15 ft.
45 ft.
30 ft.
20 ft.
15 ft.
10 ft.
7.0, 6.0 and 5.8
Capacity Models
all Gas Dryers
0
1
2
3
90 ft.
60 ft.
45 ft.
35 ft.
60 ft.
45 ft.
35 ft.
25 ft.
55 ft.
40 ft.
30 ft.
20 ft.
45 ft.
30 ft.
20 ft.
15 ft.
Spacemaker®Models
DSKS433EB
DSKS333EC
DSKP333EC
WSM2780H
0
1
2
3
46 ft.
38 ft.
31 ft.
24 ft.
37 ft.
30 ft.
22 ft.
15 ft.
30 ft.
25 ft.
20 ft.
16 ft.
24 ft.
20 ft.
14 ft.
10 ft.
Spacemaker Model
WSM2700H
0
1
2
3
56 ft.
46 ft.
34 ft.
32 ft.
42 ft.
36 ft.
28 ft.
18 ft.
30 ft.
22 ft.
16 ft.
10 ft.
22 ft.
14 ft.
10 ft.
5 ft.
Spacemaker Models
WSM2420D
WSM2480D
0
1
2
43 ft.
33 ft.
23 ft.
36 ft.
26 ft.
16 ft.
30 ft.
24 ft.
16 ft.
24 ft.
18 ft.
10 ft.

NVLR223EG – Hotpoint 5.8 Cu. Ft. Extra-Large Capacity Electric Dryer
Features and Benefits
• 5.8 Cu. Ft. Extra-Large Capacity - Handles large-size items and family size loads
• DuraDrum™- Provides long-lasting dependability and durability
• Two Heat Selections - Provide the right drying temperatures for regular and
delicate clothes
• Two Dry Cycles - Convenient, preprogrammed settings for regular and delicate clothes
• Quiet-By-Design™- Engineered for quiet operation
• Reverse-A-Door - Offers added installation flexibility
• Upfront Lint Filter - Easy to reach and clean
• Rotary Electromechanical Controls - Allow fast, easy cycle selection
• Model NVLR223EGWW – White on white
Specification Revised 12/06
470150
NVLR223E-G
Start
PushtoStart
Cottons
Automatic
Medium Heat
80 Min
Optimum Dry
OFF
OFF
70
60
50
40
30
20
Time Dry