Hotpoint Spacemaker DSKP333ECWW User manual

For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
360430
Specification Revised 11/11
Listed by
Underwriters
Laboratories
DSKP333EC
GE Spacemaker® Portable Dryer
Dimensions and Installation Information (in inches)
Dryer Note:
Dryer wall outlet must be locted within 36" of service cord entry and accessible
when dryer is mounted in position.
80
100
120
140
OFF
10
20
30
OFF
OFF
EXTRA
DRY
OPTIMUM
REGULAR HEAT
60
50
40
30
20
10
cool down
cool
down
AU TO M AT I C CYCLE
NO HEAT
FL U F F C YCLE
PU SH TO STAR T
HIGH HEAT
*
PREFERRED SETTING
TI M E D C YCLE
DSKP333ECWW
33-1/4
24-1/2
23-7/8
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on
a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are:
0" either side
3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open
area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with
a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local
codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223
for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" both sides
3" rear

For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
360430
Specification Revised 11/11
Listed by
Underwriters
Laboratories
DSKP333EC
GE Spacemaker® Portable Dryer
Dimensions and Installation Information (in inches)
Best performance
Domestic
dryer models
Maximum length of 4"
dia. rigid metal duct
Number
of
90°
turns
Exhaust hood type
A
4"
opening
B
2-1/2"
opening
DSKS433EB
DSKS333EC
DSKP333EC
WSM2780H
0
1
2
3
46 ft.
38 ft.
31 ft.
24 ft.
37 ft.
30 ft.
22 ft.
15 ft.
WSM2700H
0
1
2
3
56 ft.
46 ft.
34 ft.
32 ft.
42 ft.
36 ft.
28 ft.
18 ft.
WSM2420D*
WSM2480D*
0
1
2
43 ft.
33 ft.
23 ft.
36 ft.
26 ft.
16 ft.
A
4
B
2-1/2
*Foil ducting not allowed
A
For complete information, see installation instructions packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal
exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal
(semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be
necessary to connect the dryer to the house vent using a flexible metal (foil-type)
duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations
where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a
4” diameter can be maintained throughout the entire length of the transition duct.
Please see installation instruction packed with your dryer for complete instructions
when using flexible metal (foil type) ducting.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to
the side or bottom of dryer, add one turn.
2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be
tolerated is shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should
be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any
enclosed house floor (crawl space), or into an attic, since the accumulated lint could
create a fire hazard or moisture could cause damage. Never terminate the exhaust
into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts,
bird nesting, etc. The wall cap must also be located at least 12" above the ground or
any other obstruction with the opening pointed down.

For answers to your Monogram,® GE Profile™or
GE®appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
360430
Specification Revised 11/11
Listed by
Underwriters
Laboratories
DSKP333EC
GE Spacemaker® Portable Dryer
Features and Benefits
• 3.6 Cu. Ft. Capacity
• 3 Dry Cycles: Cottons – Automatic regular, timed dry
(150 mins.) and quick fluff (no heat) - 30 mins.
• 3 Heat Selections (Timer)
• DuraDrum™ Interior
• Quiet-By-Design™
• Portable Model
• ADA Compliant - Designed for easy operation and access
• Model DSKP333ECWW – White on white
80
100
120
140
OFF
10
20
30
OFF
OFF
EXTRA
DRY
OPTIMUM
REGULAR HEAT
60
50
40
30
20
10
cool down
cool
down
AU TO M AT I C C YCLE
NO HEAT
FL U F F C YCLE
PUS H TO STAR T
HIGH HEAT
*
PREFERRED SETTING
TI M E D C YCLE
DSKP333ECWW