Hotpoint ET6004 User manual

Instructions for Installation and Use
Electric Hob
Model: ET7424-ET6004-ET6124
TotheInstaller
Before installation fill in the product details on the back cover this book.
Theinformationcan be found ontherating plate.
TotheUser
Youmustreadtheinstructions prior to installing and using the appliance and
thenretainthemforfuturereference.

2
CONTENTS
Retention of this Instruction Book
This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of
theappliance.
If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book is also
providedso the new owner can become familiar with theappliance and safety warnings.
If the Book is lost or damaged a copy may be obtained from:
INDESIT Company UK LTD, MorleyWay, Peterborough, PE2 9JB
Introduction
Advice and recommendations
Installation and fastening
Electrical connection
Cooking zone description
The controls
Operation
The safety devices
Maintenance and care
After Sales Service
Hotpoint Guarantee
Key Contacts
3
4
5
6
7
8
9
10
11
12
13
Back Cover

3
Your new hob is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been
installed in accordance with the installation instructions detailed in this booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
Thehob is designedspecifically for domesticuse and responsibilitywill not beaccepted for usein any otherinstallation.
Introduction
*The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with this booklet.
(b) Has been properly connected to a suitable supply voltage as stated on the rating plate, attached to the
appliance.
(c) Has not been subjected to misuse or accident or been modified or repaired by any person other than the
manufacturers authorised employee or agent.
(d) Has been correctly installed.

4
Advice and recommendations
• This appliance was designed for non-professional,
household use.
• Before using the appliance, read the instructions in the
owner’s manual carefully sinceit contains all theinstruc-
tions you require to ensure safe installation, use and
maintenance.Keep this owner’s manual in a safe place
forfuture reference.
• When you have removed the packing, check whether
the appliance is intact. If you have any doubts, contact
aqualified professional before using the appliance.
• Neverleavethepackingcomponents (plastic bags, poly-
styrene foam, nails, etc.) within the reach of children
since these are a source of potential danger.
• The appliance must be installed by a qualified techni-
cian in compliance with the instructions provided by the
manufacturer.
• The latter denies all responsibility for improper installa-
tionwhich may harm persons and animals and damage
property.
• The electrical safety of this appliance can only be guar-
anteed if the latter is correctly and efficiently earthed, in
compliancewith regulations on electrical safety.Always
ensure that this vital safety measure has been taken. If
you have any doubts, call in a qualified technician to
check the electrical system thoroughly.
• The manufacturer denies all responsibility for damage
resultingfroma system which hasnotbeen earthedcor-
rectly.
• Beforepowering the appliance,check whether thetech-
nicalcharacteristicsfeaturedonthe appliance data plate
correspond with those of the mains electrical system.
• Check that the current load of the mains supply and of
thepower sockets is suitable forthe maximum power of
theappliance,indicated on the appliancedataplate. If in
doubt, contact a qualified professional.
• This appliance must only be used for the purpose for
which it was expressly designed. Any other use (such
as heating a room for example) is considered to be im-
properandconsequentlydangerous.
• The manufacturer denies all responsibility for damage
resultingfromimproperorincorrect use of the appliance.
First use:theglueused on the hob seals may leave greasy traces on the glass surface.We recommend youwipe these
off before using the appliance, with the aid of a non abrasive cleaner.During the first few hours of use, you may detect
a smell of rubber, which will disappear quickly.
• Certain fundamental rules mustbe followed when using
electrical appliances.The following are of particular im-
portance:
• do not touch the appliance with wet or damp hands,
• never use the appliance when barefoot,
• never use extensions,
• never pull on the power supply cable or the appliance
itself to unplug it from the mains socket,
• neverleavethe applianceexposedtoatmosphericagents
(rain, sun, etc.),
• donotallow children or persons whoarenot familiar with
the appliance to use it without supervision.
• Always unplug the appliance from the mains or switch
off the main switch before cleaning or performing any
cleaningor maintenance operations.
• If the surface of the glass cracks, unplug the appli-
ance immediately.Forany repairs, contact only an au-
thorisedafter-sales service centre and demand original
spare parts.Failure to comply with the above may com-
promise the safety of the appliance.
• Cut the power supply cable after disconnecting it from
the power mains when you decide not to use the appli-
ance any longer. Also make all potentially dangerous
parts of the appliance safe, above all for children who
could play with the appliance.
• The glass ceramic hob is resistant to thermal and me-
chanicalshocks.However,it may break due to a shock
caused by a sharp object, such as a tool for exam-
ple. In this case, unplug the appliance immediately
and contact an authorised after-sales service centre
to have it repaired.
• Remember that the heating area stays hot for at least
half an hour after being turned off; please refrain from
placinganycookwareorotheritemsonthecookingzone
while still hot.
• Do not turn on the heating zones if aluminium foil or
plastic items have been placed on the hob surface.
• Do not go near the heating zones when these are still
hot.
• If you use small electric appliances near the hob, make
sure their power supply cable does not come into con-
tact with the hot parts of the hob.
• Make sure all pan handles are always pointing inwards
towards the centre of the hob to prevent any accidental
spills.
Make sure that the air inlet behind the fan grille is
never obstructed. The built-in hob should, in fact, be
provided with suitable ventilation for the cooling of the
electronic components used in the appliance.
We advise against the installation of an induction hob
above an under-the-counter refrigerator (heat) or above
a washing machine (vibrations). In fact, there would be
insufficient space for the ventilation of electronic
components.

5
Thefollowing instructions areintended for a qualifiedfitter
toguidehim/her alongtheinstallation,adjustmentand tech-
nicalmaintenanceproceduresascorrectlyaspossibleand
in full compliance with the applicable norms in force.
Important :unplug the hob before all operations.
Installation
• Thishob can be builtinto a worktop simply bycutting
out the corresponding slot.
• Theworktop mustbe made with a material designed
towithstand a temperature of approximately 100°C.
• The hob should be positioned at least 40 mm away
from the back wall or any other vertical surface in
order to allow for correct ventilation and to prevent
thesurfaces around the appliance fromoverheating.
• If you wish to install the hob on top of an oven, the
latter must be fitted with a cooling fan.
• Tryto avoid installingthe hob ontop of a dishwasher;
if this is unavoidable, place a watertight separating
elementbetween the two appliances.
Fastening
Very important: It is vital that you ensure the glass ce-
ramic hob is built into a perfectly flat supporting surface.
Deformations due to improper fastening could alter the
characteristics of the hob and compromise its perform-
ance.
The fastening springs are fastened by screws (see dia-
gram).
It is vital that these screws be kept accessible at all
times.
Insert the hob into the cut-out slot, applying pressure all
along the perimeter of the hob frame so that the latter
adheres fully to the worktop.
FRONT OF HOB
KITCHEN
WORKTOP
30
40
REAR SPRING ASSEMBLY
HOB FROM BELOW
Installation and fastening
10 mm
Distance to
keep between the
cut-out slot and
the cabinet
690
520
560 +/- 1
490 +/- 1
48
785
750 +/- 1
510
490+/- 1
48

6
Electrical connection
This appliance conforms with the following European
Community Directives:
- 73/23/EEC of 19/02/73 (LowVoltage)and subsequent
amendments;
- 89/336/EEC of03/05/89(Electromagneticcompatibility)
andsubsequent amendments;
- 93/68/EEC of22/07/93 and subsequentamendments;
- 2002/96/EC
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of
in the normal unsorted municipal waste stream. Old
appliancesmust becollectedseparatelyinorder tooptimise
the recovery and recycling of the materials they contain
and reduce the impact on human health and the
environment.The crossed out“wheeledbin”symbolonthe
product reminds you of your obligation, that when you di-
spose of the appliance it must be separately collected.
Consumers should contact their local authority or retailer
forinformation concerning the correct disposal of their old
appliance.
Warning: If the hob is fitted above a built-in oven, the hob
and the oven must be connected to the mains separately
for safety reasons and to simplify operations when it is
necessary to pull the oven out for some reason.
• The electrical safety of this appliance can only be guar-
anteed if the latter is correctly and efficiently earthed,
in compliance with regulations on electrical safety.Al-
ways ensure that this vital safety measure has been
taken.If you haveany doubts, call ina qualified techni-
cian to check the electrical system thoroughly.
• The manufacturer denies all responsibility for damage
resulting from a system which has not been earthed
correctly.
• Beforepoweringtheappliance,check whether the tech-
nicalcharacteristicsfeatured ontheappliancedataplate
correspond with those of the mains electrical system.
• Check that the current load of the mains supply and of
the power sockets is suitable for the maximum power
ofthe appliance, indicatedon the appliance dataplate.
If in doubt, contact a qualified professional.
Disconnect the appliance from the electricity supply
before all operations.
Connect your hob to the electrical system by means of a
junction box: if the appliance is connected permanently
to the mains, an omnipolar circuit breaker, accessible if
necessary, with aminimumcontact openingof3mmshould
be installed.
Valid only for models without a power supply cable
Some models are not fitted with a power supply cable, as
thecableshouldbesizedaccordingto the type of electrical
connectioninuse(seeconnectiontablebelow).To connect
the cable, proceed as follows:
• Usinga screwdriver,prise onthesidetabs oftheterminal
boardcover;
• Pull open the cover of the terminal board.
LN
12345
To install the cable, proceed as follows:
• unscrewthe wire clampscrew and the contactscrews.
• to make the desired electrical connection (see table),
use the jumpers housed inside the box. Position the
power supply cable wires according to the indications
in the table.
• once the connections have been made, tighten all the
terminal screws fully.
• Fasten the supply cable in place with the clamp and
close the cover of the terminal board.
Electrical connections Voltage,
Frequency Fuses, Sections
230V-1+N~50 Hz 25 A*
2,5 mm²
* Application of the simultaneity coefficient in accordance with
cei 60335-2-6 norm

7
Cooking zone description
Induction is the fastest cooking method available.
Unlike traditional cooking zones, the induction zone does not heat up the glass surface.The pan itself is the heating
element: the pan evenly transfers heat to its contents as long as it is made of ferromagnetic material.
Each zone is controlled:
• by a selector key whose silk screen printing reproduces the cooking zone drawing,
• and by a power adjustment set comprising two parts (+,-).
Aslongas the temperature of thecookingzones remains above 60°C, evenafteruse,the residual heat indicators stay
on(the power display indicates H) to prevent the risk of burns.
HOBS ET 6004 ET 6124 ET 7424
Cooking zones Power (in W) Power (in W) Power (in W)
Back Right (BR) I 1800 ID 1800 – B 3000* I 2400 – B 3000*
Front Right (FR) I 1200 I 1200 – 600 if BR* I 1200 – 600 if BR*
Front Left (FL) I 1800 I 1800 IO 1200/2400 – B 3000*
Back Left (BL) I 1200 I 1200 I 1200 – 600
Overall power 6000 6600 7200
Ièsingle induction zone
IO èoval induction zone
B 3000* èthe zone can be boosted to 3000 W
600 if BR* èthe power of the cooking zone is reduced to 600 W as long as the BR zone is boosted
(for example)

8
The controls
Booster
15.
0
00
5.
1
2 2
6 5
10
11
12
4
8
97
3
33
3
1. ON/OFF key
2. Cooking zone selector keys
3. Power (from 0 to 9) and residual heat indicators (H)
4. Zone selection indicator:
• on: the corresponding zone is selected and can be
modified,
• off: the corresponding zone is not selected, no modi-
fication can be made.
5. Power increase key
6. Power decreasekey
7. Timer control key for cooking time programming (only
on hobs fitted with a timer)
8. Programmedcooking time indicator
9. Indicatorlight corresponding tothe programmed cook-
ingzone
10.Booster key
11.Controls lock key
12.Lock indicator light

9
Operation
Controls lock
When the hob is in use, you can lock the controls to avoid
anyaccidentalchangestothesettings(bychildren or when
cleaning,for example).
Just press the key, the indicator light next to the key
lights up and the controls are locked.
To change the power level setting or stop cooking, the
controls have to be unlocked:press the key, the indi-
cator light turns off and the controls are unlocked.
To access the setting of a cooking zone again, select the
zone by pressing the corresponding control key.
Cooking time programming
youmayprogramme all the cookingzonessimultaneously
for a maximum cooking time of 99 minutes.
Proceed as follows:
• select the cooking zone by pressing the corresponding
control key,
• set the desired heating power using the “+” and “-”
keys,
• press the programming key ,
• setthe desired cooking time usingthe “+” and “-” keys,
• confirmyourprogramming by pressing the programming
key again.
Thecountdownbeginsimmediately.
The end of programmed cooking is signalled by a beep
(oneminute long)andthecooking zoneconcernedisturned
off.
When you connect the hob to the power supply, a beep
will sound after a few seconds: you can now turn the hob
on.
Turning on the hob
Press key to turn the hob on.
Cooking zone control
Each cooking zone is operated by a control key and by a
power adjustment set (+ and -).
Turning on a cooking zone
• To turnacooking zoneon,press the corresponding con-
trol key and set the desired heating power (from 0 to 9)
using the “+” and “-” keys.
• To set the maximum power directly (9), press key “-”
briefly.
Turning off a cooking zone
To turn off a cooking zone, press the corresponding con-
trol key and:
• press both “+” and “-”simultaneously:thecooking
zone power drops immediately to zero and the zone
is turned off.
•orpressthe“-” key:the heating powerdropsprogres-
sively until the zone eventually turns off.
Turning off the hob
Press the key; the appliance has been turned off.
If you have locked the hob controls (see paragraph be-
low), the same will still be locked when you turn the hob
backon. Unlock the controls inorder to operate the cook-
ing zones.
The booster
To speed up the rise in temperature of the cooking zones
(see cooking zone table on the previous page), press the
Booster
key.
The power display will indicate “P”.The booster function
comes to an automatic stop after 4 minutes.
When the booster function is on, certain cooking zones
(see the cooking zone table on the previous page) are
limited to a maximum power of 600W.
0
00
5.

10
The safety devices
Acoustic signal
Anomalies such as:
• an object (such as a saucepan or a lid, etc.) placed
for more than 10 seconds on the control zone,
• boiled-overliquidsor food spilled on thecontrolzone,
• prolonged pressure on a key,...
could cause a beep to sound and the hob to turn off.
To stop the beep from sounding, remove the cause of the
malfunction.
To use the hob, turn it back on and re-select the cooking
zone(s) you wish to use.Set the desired heating power.
Safety cut out
Your appliance is fitted with a safety cut out which inter-
venes after a certain amount of time (see table below)
depending on the power setting.When the safety cut out
has intervened, the power display indicates “0”.
for example: the back right cooking zone is set to 5 and
the front left zone is set to 2.The back right zone will turn
off after 3 hours of operation and the front left zone will
turn off after 10 hours of operation.
To unlock the controls, turn the hob off by pressing the
key.
Overheating protection device
Shouldyourappliance’s electronic componentsoverheat,
thehob will turn offautomatically and “—” will come upon
the power level display.
Theletter will disappear assoon as the temperaturedrops
back down to an acceptable level.
Power level Maximumduration of operation
1-2 10hours
3 5hours
4 4hours
5-6 3hours
7-8 2hours
9 1hour
Pan recognition
Each induction cooking zone is fitted with a pan recogni-
tion device. The cooking zone only provides heat in the
presence of a pan which is suitable for the cooking zone.
A blinking pan recognition indicator could signal:
• that the pan is made of unsuitable material, which is
notferromagnetic,
• that the diameter of the pan is too small,
• that the pan has been removed.
Always match the diameter of the pan with that of the
cooking zones.
Warning:oval cooking zones
Oval cooking zones can only be boosted if the full oval is
enabled.
Donot place twosmall saucepans on ovalcooking zones.
What cookware to use
Given that induction only exists when the magnetic field
issealedbya metallic recipient, thepanstopsbeingheated
as soon as it is taken off the cooking zone.
Use cookware made of material which is compatible
with induction (ferromagnetic material).
Cast iron, enamelled steel or special induction stain-
less steel saucepans are ideal.
Copper, ceramic,earthenware,glass,terracotta,aluminium
and non magnetic stainless steel cookware is incompat-
iblewith induction cooking.
The easiest way to find out whether the pan is suitable
is with a magnet. If the magnet is attracted by the pan
bottom and stays “stuck” to the same, the pan is made of
ferromagneticmaterial and canbe used onyour induction
hob.
We recommend you use pans with a very flat and thick
bottom and avoid at all costs all cookware with irregular
rough bases which could scratch the glass surface.
*
SUITABLE UNSUITABLE
Cast iron
Enamelled steel
Special stainless steel
Copper,
Aluminium, Glass, Earthenware,
Ceramic, non magnetic Stainless steel
For the attention of wearers of pacemakers or other
activeimplants:
The hob complies with all current standards on
electromagneticinterference.Yourinductionhobistherefore
perfectly in keeping with legal requirements (89/336/CEE
directives).It is designed not to create interference onany
otherelectrical apparatus beingused on condition thatthe
apparatus in question also complies with this legislation.
Yourinduction hob generatesshort-rangemagneticfields.
Toavoidany interferencebetween yourinduction hob and
a pacemaker, the latter must be designed to comply with
relevantregulations.Inthisrespect,wecan only guarantee
ourownproduct conformity.Pleaseconsultthepacemaker
manufacturer or your doctor concerning its conformity or
any possible incompatibility.

11
Hobcare
The vitroceramic glass used for the heating surface is
smooth and poreless and it is also resistant to thermal
shocks and to mechanical shocks under normal condi-
tionsof use.In orderto preservetheseproperties,werec-
ommend you care for your hob as follows:
• for ordinary maintenance, just wipe it with a damp
spongeand dry it thoroughly using paper towels.
• If the hob is dirty, rub clean using a special cleaner
suitablefor vitroceramic glass,rinse off anddry thor-
oughly.
• foodresidue anddirt can be removedusing a special
scraper. Do this as soon as possible, do not wait for
the hob to cool down in order to avoid incrustations.
For excellent results, use a special stainless steel
wool pad for vitroceramic glass cleaning soaked in
soapy water.
• When the hob is clean, you can apply a special prod-
uct for the care and protection of the same: this type
of product leaves an invisible film on the surface of
the hob to protect the same against any spills and
boiled-over food. It is best if you do this when the
hob is lukewarm or cold.
• Makesure you always rinse thehob with clean water
and dry it thoroughly: otherwise the cleaning prod-
ucts could become encrusted onto the hob during
subsequentcooking.
Recommendations
• Neveruseabrasive or corrosive substances, such
as aerosolcleaners for grills and ovens, stain remov-
ersor rust removers, scouring powdersand abrasive
sponges: even the delicate ones could scratch the
hob surface irreversibly.
• We recommend youkeep all items which could melt
away from the hob,such as plastic utensils,sugar
or products with a high sugar content. Should liq-
uidboil overontothe hobsurface, remove it immedi-
ately (while the hob is still hot) using a razor blade
scraper, in order to avoid damaging the surface.
• Use this hob exclusively for cooking. Do not place
items on the hob when the same is not in use. Do not
usethe hob as awork surface (by placinglids, sauce-
pans or dishcloths on it, for example), nor as a chop-
pingboard.
• Neverleave aluminium wrappers, aluminium foil and
plastic cookware on the hob when hot or still warm.
• Donot use steamcleaners or highpressure cleaners
toclean your appliance.
• Donot place metal items on the hob (such asknives,
spoons, lids, etc.).
• Never heat up unopened tins: they could burst.
Theguarantee does not cover damageto the hob caused
by incorrect use.
Maintenance and care
Advice on using your appliance
To get the best from your hob, it is vital that you follow a
fewfundamentalrules during cooking andwhenpreparing
food.
• Use pans with a flat bottom so they adhere fully to the
heatingzone.
• Always use pans whose diameter covers the cooking
zone fully so that all the available heat can be used.
• Make sure the pan base is always clean and dry, to
guarantee good contact and long life for the cooking
zones and pans alike.
• Avoid using pans used normally on gas burners.The
concentration of heat on gas burners can warp the
bottomofthepan, consequently you wouldneverobtain
the desired result when using the pan on the glass
ceramichob.
• Never leave a cooking zone on without a pan on it as
themaximumheat levelwouldbereached very quickly,
which could damage the heating elements.
• The glass ceramic hob is resistant to thermal and
mechanical shocks. However, it may break due to a
shock caused by a sharp object. In this case, unplug
the appliance immediately andcontactanauthorised
after-sales service centre to have it repaired.
Alwayskeepyourhobclean.Beforeproceedingwithmain-
tenance operations, check that all the cooking zones are
turned off and have cooled down completely.
Stainless steel frame (only on somemodels)
Stainless steel can stain as an effect of enduring contact
with limescale in water or as an effect of highly aggres-
sive detergents (containingphosphorus).Werecommend
you rinse and dry it thoroughly after maintenance. It is
preferable to remove any water spills immediately.

GB 12
"No company is better positioned to offer an after sales service on a
Hotpoint appliance than us - the manufacturer"
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts
and labour guarantee for the first 12 months. In addition to this you also have the advantage of free
replacement parts for the first 5 years when fitted by a Hotpoint
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales
service options:
Repair Service and Information Help Desk
UK:08709066066
www.theservicecentre.co.uk
Republic of Ireland: 1850 302 200
Note: Our operators will require the Model number and the Serial number of your appliance
Available 364 days a year with a fast, effective and value for money service.We have the largest white
goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a
parts and labour guarantee for 12 months from the date of the repair.
If you require any information or have any questions about your appliance, our operators are on hand with
help and advice.
All this ensures that you will receive the best available after sales service possible.
Extended Warranties
UK: 08709 088 088
www.theservicecentre.co.uk
Republic of Ireland: 1850 502 200
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover
plans to give you total peace of mind.
l Repair Protection Plan - FREE service repairs for a single Hotpoint appliance during the period
of cover.
l Kitchen Cover - FREE service repairs for all your Hotpoint appliances less than 8
years old.
Genuine Parts and AccessoriesUK: 08709 077 077
www.theservicecentre.co.uk
Republic of Ireland: [phone]
A wide range of genuine parts and accessories are available from our hotline or through our web site.
Genuine parts and accessories, extended warranties and service repairs are all
available on our web-site at:
www.theservicecentre.co.uk
After Sales Service

GB
13
Guarantee
"Satisfaction guaranteed or your money back"
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service
or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange for an
engineer to call. If the technical problem is not resolved under this guarantee, we will replace your
machine or, if you prefer, give you your money back.
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free
replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker
hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.
Guarantee terms and conditions
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the
following provisions that your appliance:
lHas been installed and used correctly in accordance with this instruction booklet.
lHas been used solely for domestic purposes and is located on domestic premises (ie. not for
commercial or trade use).
lHas been properly connected to a suitable electrical supply voltage as stated on the appliance
ratingplate.
lHas not been subject to misuse, accident, modified or repaired by anyone other than one of our
own service engineers.
For pre purchase information on any other Hotpoint product call: 08701 50 60 70
or visit: www.hotpoint.co.uk
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to
use quality recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the
appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged
into a mains socket, and the door cannot be locked shut.

14

15

Key Contacts
After Sales Service
02/2006-195043663.03
Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in
both the appliances and services we offer.
Repair Service and Information Desk
UK: 08709 066 066
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
www.theservicecentre.co.uk
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Modelnumber:
Serialnumber:
Extended Warranties
UK: 08709 088 088
(Open 8 to 8 Mon - Sun)
www.theservicecentre.co.uk
Republic of Ireland: 1850 502 200
Genuine Parts and Accessories
UK: 08709 077 077
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)
www.theservicecentre.co.uk
Republic of Ireland: [phone]
Indesit Company UK Ltd.Morley Way, Peterborough, PE2 9JB.