HP 8886 - Photosmart Camera Dock Digital Docking... User manual

ReWritable
Recordable
Recordable
Recordable
ReWritable
PHONES VOLUME
WRITING DISC IN
ACTIVE
PHONES VOLUME
WRITING DISC IN
ACTIVE
OPEN/CLOSE
OPEN/CLOSE
01_LAYOUT_GB 22-11-2000 09:21 Pagina 1a

Front view ©
1. Headphone plug
2. Headphone volume control
3. Write indicator
4. Disc Tray
5. Disc in/Active/error
indicator
. Open/Close button
7. Emergency eject
Rear view
8. Audio Line Out connector
9. Jumperblock
10. IDE connector
11. Host DC power connector
12. Digital Audio out
ReWritable
Recordable
Recordable
Recordable
ReWritable
PHONES VOLUME
OPEN/CLOSE
WRITING DISC IN
ACTIVE
PHONES VOLUME
OPEN/CLOSE
WRITING DISC IN
ACTIVE
CDRW 8x4x32 - Compact Disc Recordable/Rewritable
FIG 1
12
MASTER
SLAVE
CABLE SELECT
AUDIO OUT
R GND L
C
S
S
L
M
A
IDE PIN 1
DC INPUT
+5 GND +12
MASTER
SLAVE
CABLE SELECT
AUDIO OUT
R GND L
C
S
S
L
M
A
IDE PIN 1
DC INPUT
+5 GND +12
MASTER
SLAVE
CABLE SELECT
AUDIO OUT
R GND L
C
S
S
L
M
A
IDE PIN 1
DC INPUT
+5 GND +12
Front view
Rear view
Vorderansicht d
1. Anschlußbuchse Kopfhörer
2. Lautstärke Kopfhörer
3. Schreibanzeige
4. Schublade
5. Diskette ein/Aktiv/Fehler
anzeige
. Open/Close Taste
7. Notauswurf
Rückansicht
8. Analog Audio-Ausgang
9. Jumperblock
10. IDE Anschluß
11. Host Gleichspannungs-
anschluß
12. Digital Audio-Ausgang
Panneau avant f
1. Prise pour casque
2. Commande du volume du
casque
3. Témoin lumineux
d’enregistrement
4. Tiroir à disque
5. Témoin disque/Activé/erreur
. Touche ouvrir/fermer
7. Ejection d’urgence
Panneau arriëre
8. Connecteur de sortie de ligne
audio
9. Cavaliers
10. Connecteur IDE
11. Connecteurs au bloc
d’alimentation C.C. hôte
12. Sortie audio numérique
Parte anteriore i
1. Presa cuffie
2. Controllo volume cuffie
3. Indicatore di scriture
4. Cassetto del disco
5. Indicatore disco
inserito/Attivo/Errore
. Tasto Apertura/Chiusura
7. Espulsione di emergenza
Parte posteriore
8. Connettore Line Out Audio
9. Blocco Jumpers
10. Connettore IDE
11. Connettore alimentazione DC
12. Uscita audio digitale
Vista frontal e
1. Clavija de los auriculares
2. Control del volumen de los
auriculares C.D.
3. Indicador escritura
4. Bandeja del Disco
5. Indicador de Disco
introducido/Activo/Error
. Bóton de Apertura/Cierre
7. Expulsión de emergencia
Vista posterior
8. Conector de salida de Línea
de Audio
9. Bloque de conectores
10. Conector IDE
11. Conector de alimentacíon
12. Salida de audio digital
Voorzijde ñ
1. Hoofdtelefoon aansluiting
2. Hoofdtelefoon volumeregelaar
3. Schrijfindicator
4. Disc-lade
5. Disc aanwezig/
Actief/foutindicator
. Openen/sluiten-toets
7. Nood-eject
Achterzijde
8. Audio-connector lijnuitgang
9. Jumper-block
10. IDE connector
11. Voedingsconnector host
computer
12. Digital audio-uitgang
01_LAYOUT_GB 22-11-2000 09:21 Pagina 1b

01_LAYOUT_GB 22-11-2000 09:21 Pagina 1c

WARNING
This device complies with Part 15 of the FCC (U.S.A.) Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can be used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning this equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.
FOR CANADA (ICES-003)
This class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte toutes les exigences du
Reglement sur le materiel brouilleur de Canada.
FOR EUROPE
“The CDRW 8x4x32 is in conformity with the EMC
directive and low-voltage directive
IMPORTANT
Any change or modifications to the equipment by the user not expressly
approved by the grantee or manufacturer could void the user's authority
to operate such equipment.
01_LAYOUT_GB 22-11-2000 09:21 Pagina 1d

CONTENTS
CONTENTS
CDRW
ENGLISH ©
DEUTSCH d
FRANÇAIS f
ITALIANO i
ESPAÑOL e
NEDERLANDS ñ
EINLEITUNG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
BEDIENELEMENTE UND ANSCHLÜSSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
BEDIENUNG UND PRÜFUNG DES CD-RECORDABLE/REWRITABLE-SYSTEMS . . . . . . . . . . . . . . . . .41
ZUSÄTSLICHE INFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
HINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
RÉSUMÉ DES COMMANDES ET CONNEXIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
UTILISEZ/TESTEZ VOTRE SYSTÈME POUR CD ENREGISTRABLE/RÉENREGISTRABLES . . . . . . . . . . .55
INFORMATIONS COMPLÉMENTAIRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
REMARQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
INTRODUZIONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
INSTALLAZIONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SOMMARIO DEI COMANDI E DEI COLLEGAMENTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
USO/VERIFICA DEL FUNZIONAMENTO DEL SISTEMA REGISTRATORE/REWRITABLE . . . . . . . . . . . 9
ALTRE INFORMAZIONI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
NOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
INTRODUCCIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
INSTALACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
RESUMEN DE CONTROLES Y CONECTORES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
FUNCIONAMIENTO/PRUEBA DEL SISTEMA DE CD-GRABABLE/REESCRIBIBLE . . . . . . . . . . . . . . . . .83
INFORMACIÓN ADICIONAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
OBSERVACÍONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
INLEIDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
INSTALLEREN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
BEDIENINGSOVERZICHT EN AANSLUITINGEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
BEDIENEN/TESTEN VAN UW CD-RECORDABLE/REWRITABLE-DRIVE . . . . . . . . . . . . . . . . . . . . . . .97
EXTRA INFORMATIE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
OPMERKINGEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SUMMARY OF CONTROLS AND CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
OPERATING/TESTING YOUR CD-RECORDABLE/REWRITABLE SYSTEM . . . . . . . . . . . . . . . . . . . . . .11
ADDITIONAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
01_LAYOUT_GB 22-11-2000 09:21 Pagina 1e

LASER SAFETY
This unit employs a laser. Do not remove the cover or attempt to service this
device when connected due to the possibility of eye damage.
LASER-SICHERHEIT
In das Gerät ist ein Laser eingebaut. Nehmen Sie die Abdeckung nicht ab und
versuchen Sie nicht, das Gerät zu reparieren, solange es angeschlossen ist. Es
besteht die Gefahr einer Augenverletzung.
CAUTION
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS LASER RADIATION EXPOSURE.
WARNUNG
DIE VORNAHME VON REGELUNGEN ODER EINSTELLUNGEN ODER DIE
DURCHFÜHRUNG VON VERFAHREN, DIE NICHT IN DIESEM DOKUMENT
(DIESER BESCHREIBUNG; IM NACHSTEHENDEN TEXT) ANGEGEBEN
SIND, KANN EINE GEFÄHRLICHE EINWIRKUNG VON LASERSTRAHLUNG
ZUR FOLGE HABEN.
CLASS 1
LASER PRODUCT LUOKAN I
LASERLAITE
KLASS 1
LASERAPPARAT
CAUTION INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO
BEAM
VARO! AVATTAESSA OLET ALTIINA NÄKYMÄTTÖMÄLLE LASER SÄTTEILYLLE
ÄLÄ KATSO SÄTEESEN
VARNING OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD
BETRAKTA EJ STRÅLEN
ADVERSEL USYNLIG LASERSTRÅLING VED ÅBNING. UNDGÅ UNSAETTELSE FOR
STRÅLING
DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT
EXPOSURE TO BEAM
VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET
NICHT DEM STRAHL AUSSETSEN
KLASSE 1
LASER-PRODUKT
LASER
Type Semiconductor laser GaAlAs
Wavelength 780~800 nm (at 25° C)
Output Power (measured above the objective lens)
1 mW (Read)
30 mW (Write)
Beam divergence 0 degree.
01_LAYOUT_GB 22-11-2000 09:21 Pagina 1f

ENGLISH
CDRW
INTRODUCTION
INTRODUCTION
INTRODUCTION
CDRW 8x4x32 is a new generation Half Height 5.25" Built-in CD-
Recor able/ReWritable rive with the popular (Enhance ) IDE
interface.
The rive is in fact a multi-function evice, since it can be use as:
• fast CD-ROM rea er (max 32x)
• 8x spee CD-Recor er, e.g. to recor your own
CD-ROM's or Au io-CD's
• 4x spee CD-ReWritable evice to use as your
personal storage me ium, by using Incremental
Packet Writing
The CDRW 8x4x32 is the i eal tool for publishing large amounts of
ata in compact form on CD. The Incremental Packet Writing
function will make this rive attractive to the general esktop PC-
user for personal ata storage.
CD-Recor able iscs can be recor e at 8x spee , an in all
stan ar formats, e.g. CD-Au io, CD-ROM (XA), CD-i an Vi eo-
CD among others.
Since these iscs are recor e in accor ance with the Orange Book
(part II) specification, these iscs can be playe back on all
compatible CD-players.
CD-ReWritable is a feature which allows re-use of previously
written iscs by rewriting portions or the complete isc in
accor ance with the Orange Book (partIII) specification. These
iscs can be recor e at qua ruple spee in all stan ar formats.
1
01_LAYOUT_GB 22-11-2000 09:21 Pagina 1

ENGLISH
CDRW
INTRODUCTION
INTRODUCTION (CONT)
2
Features of the CDRW 8x4x32 CD-Recor able/ReWritable rive:
• Multi-function evice (CD-ROM rea er, CD-Recor er
an CD-ReWritable rive)
• Supports Incremental Packet Writing for ata storage
applications an " rag & rop" File System support
through the CD-UDF stan ar (en orse by Optical
Storage Technology Association or OSTA)
• Supports stan ar ise Multi Me ia Comman set
(MMC-2) as stan ar ise by the American National
Stan ar s Institute (ANSI)
• Plug & Play rea compatibility un er Win ows
95/98/2000 an Win ows NT
• Interfaces irectly to low cost stan ar ise
(Enhance ) IDE connector on PC motherboar
• Supports Fast Format (Backgroun Formatting)
epen ing on the application software, which
re uces formatting time of a CD-RW isc to only a
few minutes.
Unpacking
If the CDRW 8x4x32 package shows evi ence of rough han ling or
amage an the rive oes not function properly on initial startup:
return the rive an amage package to your supplier an request
a replacement.
Lift out the CDRW 8x4x32 an remove the packing pieces.
Check that the package contains following items :
• User manual
• Mounting screws
An IDE flatcable an /or au io cable coul be part of this package
epen ing on the commerical package. It can also be obtaine
from your local supplier.
01_LAYOUT_GB 22-11-2000 09:21 Pagina 2

ENGLISH
CDRW
INSTALLATION
INSTALLATION
3
INSTALLATION
Precautions
This CD-Recor able/Rewritable rive, like all electronic
equipment, is static sensitive.
• Please take the proper precautions when han ling the rive,
for example by touching the PC - chassis before touching the
rive.
• Avoi touching the IDE connector pins as well as the au io-
connector pins an the jumper pins.
• Keep the rive in its con uctive wrapping until you are rea y
to install the rive in your computer.
Safety Precautions
• Europe: This rive shall be installe only with an EN60950
(IEC950) approve Power supply.
• USA/Cana a: This rive is for use only with IBM compatible
UL liste Personal Computers or Macintosh UL
liste workstations weighing less than 18 kg.
Copyright Statement
It is a criminal offence, un er applicable copyright laws, to make
unauthorise copies of copyright-protecte material, inclu ing
computer programs, films, broa casts an soun recor ings. This
equipment shoul not be use for such purposes.
01_LAYOUT_GB 22-11-2000 09:21 Pagina 3

ENGLISH
CDRW
INSTALLATION
INSTALLATION (CONT)
4
Installing the rive
11Turn off your computer, monitor an other peripherals.
To isconnect your configuration completely from the mains,
the mains plug has to be isconnecte .
OPEN THE COVER FLAP OF THIS BOOKLET FOR
LOCATING THE DRIVE-CONNECTORS AND THEIR ORIENTATION.
22Remove the cover from your computer.
Please consult the manuals that came
with your computer for specific etails.
NOTE:
01_LAYOUT_GB 22-11-2000 09:21 Pagina 4

ENGLISH
CDRW
INSTALLATION
INSTALLATION (CONT)
5
33In or er to mount the rive insi e your PC (or other type
of computer), locate a free 5.25" bay an follow the instructions,
as provi e with your computer systems, for installing the rive.
When you are planning to use 8 cm iscs your rive shoul be
mounte horizontaly or you shoul use an a apter
(for information contact your local supplier).
44You have several possibilities to install your IDE ata cable
epen ing on your existing configuration:
(See page 18 for Jumper block)
A) Har -Disc connecte as Master to Primary IDE Port,
CD-ROM connecte as Master to Secun ary IDE Port:
Connect CDRW 8x4x32 as Slave to Secun ary IDE Port.
Primary Port Har -Disc -
Secun ary Port CD-ROM -
MASTER SLAVE
Primary Port Har -Disc -
Secun ary Port CD-ROM CDRW 8x4x32
MASTER SLAVE
Jumper
Block
Existing
PC Configuration
PC Configuration
after Installation
C
SSM
01_LAYOUT_GB 22-11-2000 09:21 Pagina 5

ENGLISH
CDRW
INSTALLATION
INSTALLATION (CONT)
6
B) Single Har - isc connecte as master to Primary IDE Port:
Connect CDRW 8x4x32 as Master to Secun ary Port.
C) Har - isc connecte as Master to Primary IDE Port,
CD-ROM connecte as Slave to Primary IDE Port:
Connect CDRW 8x4x32 as Master to Secun ary IDE Port.
D) CS (Cable Select) (With use of CS Cable)
The MASTER/SLAVE settting will be set automatically
epen ing on the har ware configuration. Please refer to
your PC manual for etails.
INSTALLATION A IS PREFERRED FOR SYSTEMS WITH
AN IDE HARD-DISC AND CD-ROM.
INSTALLATION B IS PREFERRED FOR SYSTEMS WITH
ONLY AN IDE HARD-DISC.
NOTE:
NOTE:
Primary Port Har -Disc CD-ROM
Secun ary Port - -
MASTER SLAVE
Primary Port Har -Disc CD-ROM
Secun ary Port CDRW 8x4x32 -
MASTER SLAVE
Jumper
Block
C
SSM
Existing
PC Configuration
PC Configuration
after Installation
Primary Port Har -Disc -
Secun ary Port - -
Primary Port Har -Disc -
Secun ary Port CDRW 8x4x32
Jumper
Block
C
SSM
Existing
PC Configuration
PC Configuration
after Installation
01_LAYOUT_GB 22-11-2000 09:21 Pagina 6

ENGLISH
CDRW
INSTALLATION
INSTALLATION (CONT)
7
55Locate the free en of the IDE ata cable an threa it
out through the open rive bay. Do the same with the
power cable an the (optional) au io cable ( igital or
analogue). Your system will either be equippe with an analogue
or igital soun car connector. Use the appropriate connector on
the rive recognisable with the amount of pins.
66Connect your (optional) au io cable, IDE
ata cable an the power cable into the
back of the CDRW 8x4x32. Make sure you
correctly align pin 1 of the cable to pin 1 of
the connectors.
Audio cable
(Digital or
analogue)
IDE
Data cable
Power
cable
11
1
IDE
Data Cable
Power
Cable
Audio
Cable
(digital)
Audio
Cable
(analogue)
01_LAYOUT_GB 22-11-2000 09:21 Pagina 7

ENGLISH
CDRW
INSTALLATION
INSTALLATION (CONT)
8
77Insert the CDRW 8x4x32 into the rive bay. Using all the
screws inclu e in the bag to secure the CDRW 8x4x32
into the bay.
88Replace the cover. Connect the mains plug
of your configuration. When you have
successfully installe the rive an establishe all connections, it
is now time to switch on the PC. You are rea y to install the
software.
ReWritable
Recordable
Recordable
Recordable
ReWritable
PHONESVOLUME
OPEN/CLOSE
WRITINGDISC IN
ACTIVE
PHONESVOLUME
OPEN/CLOSE
WRITINGDISC IN
ACTIVE
01_LAYOUT_GB 22-11-2000 09:21 Pagina 8

ENGLISH
CDRW
CONTROLS
CONTROLS
9
SUMMARY OF CONTROLS AND CONNECTIONS
Front view (See Cover Flap Fig.1)
1. HEADPHONE PLUG
Connect your hea phone to listen to au io or music iscs (or
tracks).
2. HEADPHONE VOLUME CONTROL
Turn the wheel to the right to increase the au io volume of
your hea phone.
3. WRITE INDICATOR
Lights “orange” when writing of a isc occurs.
Flashes “orange” uring write emulation.
4. DISC TRAY
5. DISC IN/ACTIVE/ERROR in icator ( ual color LED)
Lights “green” when a isc is present. Flashes “green”
asymmetrically when ata is being rea from isc or written to
the isc. Flashes “green” symmetrically when starting up a isc.
Lights “re ” upon error (e.g. after faile selftest).
6. OPEN/CLOSE BUTTON
Press the OPEN/CLOSE button to open the isc loa ing tray.
To close the isc loa ing tray, gently push the front of the
tray or press the Open/Close button.Using the open/close
button to close the tray will calibrate the movement of the
tray in case this evitates from the original setting ue to for
instance eaging
7. EMERGENCY EJECT
In case you are not able to power up your PC, an want to take
the isc out of the rive, push with a ro (paperclip) of about
5 cm through the hole in the front to isengage the gears
insi e. Then pull the tray out. After taking the isc, gently push
it back to its original position
This is only in case of emergency, not meant for normal
operations.
01_LAYOUT_GB 22-11-2000 09:21 Pagina 9

ENGLISH
CDRW
(CONT)
CONTROLS
CONTROLS
10
Rear view (See Cover Flap Fig.1)
8. AUDIO LINE OUT CONNECTOR
1: Left 2: GND
3: GND 4: Right
9. JUMPERBLOCK
These jumpers are use to select Master/Slave mo e an
Cable Select (See Appen ix for more information).
10. IDE CONNECTOR
40 pin IDE flatcable connector (See Appen ix for more
information).
11. HOST DC POWER CONNECTOR (type AMP 00641737-1)
1: +12V 2: GND
3: GND 4: +5V
12. DIGITAL AUDIO OUT
1 2
Pin number Meaning
1 Dig. Au io signal
2 Groun
Pinout table for igital Au io Out connector
4 3 2 1
4 3 2 1
01_LAYOUT_GB 22-11-2000 09:21 Pagina 10

ENGLISH
CDRW
OPERATING/TESTING
OPERATING/TESTING
11
OPERATING/TESTING YOUR CD-RECORDABLE/REWRITABLE
SYSTEM
Loa ing an unloa ing a isc
11To open the tray: Press the Open/Close button.
22Loa a isc, with the label facing upwar s. The tray
accommo ates iscs with 8 cm iameter (CD-Single) or the more
usual 12 cm iscs (the 8 cm isc can only be use in rives
mounte horizontaly).
33To close the tray, either push gently at the front of the tray or
press the Open/Close button.
FOR OPTIMAL RESULTS, USE ORANGE BOOK CD-R OR
CD-RW MEDIA.
DON’T USE GENERAL PURPOSE COMMERCIAL HEAD
CLEANING DISCS.
8 CM R- AND RW-DISCS CAN NOT BE RECORDED IN THIS
DRIVE.
NOTE:
NOTE:
NOTE:
PHONESVOLUME
OPEN/CLOSE
WRITINGDISC IN
ACTIVE
PHONESVOLUME
OPEN/CLOSE
WRITINGDISC IN
ACTIVE
(5")
12cm
(3")
8cm
(3")
8cm
OPE /CLOSE
Button
01_LAYOUT_GB 22-11-2000 09:21 Pagina 11

ENGLISH
CDRW
(CONT)
OPERATING/TESTING
OPERATING/TESTING
12
DO NOT SWITCH OFF THE COMPUTER AND/OR THE DRIVE
DURING THE RECORDING PROCESS, SINCE THIS MIGHT RESULT IN
AN UNREADABLE DISC. PLEASE MAKE SURE THAT THE COMPUTER
HAS FINISHED IT’S RECORDING PROCESS AND THAT THE WRITE
INDICATOR ON THE FRONT OF THE DRIVE IS OFF.
Operating the CD-Recor able/Rewritable on the
computer
Specific Application Software running on the computer platform in
use, esigne to work with the CDRW 8x4x32, must
be use in or er to be able to operate the CDRW 8x4x32 correctly.
Software installation
The installation an operation of the necessary software is epen ent
of the computer configuration in which the CDRW 8x4x32 is to be
use , e.g. PC’s, Win ows 95/98/2000, Win ows NT, UNIX or other
Operating Systems. Contact your supplier for the full list of
supporte host configurations an available software packages.
All tra emarks acknowle ge .
Comman escription
This rive supports comman s base on the in ustry stan ar MMC
(MultiMe ia Comman set). An extensive escription of the total
comman set is available on request.
NOTE:
01_LAYOUT_GB 22-11-2000 09:21 Pagina 12

ENGLISH
CDRW
ADDITIONAL INFO
ADDITIONAL INFO
13
ADDITIONAL INFORMATION
Care of iscs
• When loa ing a isc, allow time for the oor to open an then
gently insert the isc.
• Han le iscs only by the outer an inner e ges.
•Never write with a ballpoint on the
surface of the isc.
•Do not store a isc in places with high
temperature an humi ity. Do not place
the isc un er irect sunlight.
• Store iscs in their cases to prevent ust contamination,
scratches, ben ing an other amages.
• When a isc becomes irty, clean it with a cleaning cloth. Wipe
the isc from the centre out. Do not use solvents such as
benzine, thinner, commercially available cleaners, or anti-static
flui s. Using flui s of these types may amage the isc.
• Empty iscs are separately available through your ealer.
• To get an optimal temperature controle, you shoul close your PC
after installing the rive in this way the central fan will help cooling
your rive an keep performance accor ing specification.
• Unloa ing a isc after recor ing might take some time, because
the rive has to up ate the TOC before the isc can be
ejecte .
01_LAYOUT_GB 22-11-2000 09:21 Pagina 13

ENGLISH
CDRW
(CONT)
ADDITIONAL INFO
ADDITIONAL INFO
14
Technical ata
PERFORMANCE
Capacity
120mm isc 650 Mbytes/700 Mbytes
(74/80mm Au io)
80mm isc 200 Mbytes
Access time average 1/3 ata(1) 120 msec.
Access time max(1) < 300 msec.
Data-transfer-rate (recor ing) 1,4 MB/sec sustaine (8x
spee , mo e 2 ata)
Data-transfer-rate (rea only) Up to 5600 Kbytes/sec
(32 spee , mo e 2 ata)
Max. burst rate >_ 2,5 Mbytes/sec
Interface (Enhance ) IDE
Form factor 5,25" Half Height
Data integrity from rive,
assuming new iscs 10-12
Data buffer 2Mb
Disc loa ing Tray (motorise )
THIS DRIVE HAS AN ANGULAR VELOCITY 32 READ
SPEED MODE, THIS MEANS THAT THE MOMENTARY SPEED
WIL INCREASE FROM 21 TIMES SPEED AT THE INNER DIAMETER
OF THE DISC (IE. AT BEGINNING OF LEAD IN) TO THE MAXIMUM
OF 32 TIMES SPEED AT THE OUTER EDGE OF THE DISC.
(1) After spin up, including latency and command overhead, at 32 speed (only valid for
reading).
NOTE:
01_LAYOUT_GB 22-11-2000 09:21 Pagina 14