HP Rp5700 - Point of Sale System Manual

Computer Setup (F10) Utility Guide
HP rp5700

© Copyright 2007, 2009 Hewlett-Packard
Development Company, L.P. The
information contained herein is subject to
change without notice.
Microsoft, Windows, and Windows Vista are
either trademarks or registered trademarks
of Microsoft Corporation in the United States
and/or other countries.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products
and services. Nothing herein should be
construed as constituting an additional
warranty. HP shall not be liable for technical
or editorial errors or omissions contained
herein.
This document contains proprietary
information that is protected by copyright. No
part of this document may be photocopied,
reproduced, or translated to another
language without the prior written consent of
Hewlett-Packard Company.
Computer Setup (F10) Utility Guide
HP rp5700
Second Edition (July 2009)
Document Part Number: 445247-002

About This Book
This guide provides instructions on how to use Computer Setup. This tool is used to reconfigure and
modify computer default settings when new hardware is installed and for maintenance purposes.
WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily
harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage
to equipment or loss of information.
NOTE: Text set off in this manner provides important supplemental information.
ENWW iii

iv About This Book ENWW

Table of contents
Computer Setup (F10) Utility
Computer Setup (F10) Utilities ............................................................................................................. 1
Using Computer Setup (F10) Utilities .................................................................................. 2
Computer Setup—File ......................................................................................................... 3
Computer Setup—Storage .................................................................................................. 4
Computer Setup—Security .................................................................................................. 6
Computer Setup—Power ..................................................................................................... 8
Computer Setup—Advanced ............................................................................................... 9
Recovering the Configuration Settings ............................................................................................... 11
ENWW v

vi ENWW

Computer Setup (F10) Utility
Computer Setup (F10) Utilities
Use Computer Setup (F10) Utility to do the following:
●Change factory default settings.
●Set the system date and time.
●Set, view, change, or verify the system configuration, including settings for processor, graphics,
memory, audio, storage, communications, and input devices.
●Modify the boot order of bootable devices such as hard drives, optical drives, or USB flash media
devices.
●Enable Quick Boot, which is faster than Full Boot but does not run all of the diagnostic tests run
during a Full Boot. You can set the system to:
◦always Quick Boot (default);
◦periodically Full Boot (from every 1 to 30 days); or
◦always Full Boot.
●Select Post Messages Enabled or Disabled to change the display status of Power-On Self-Test
(POST) messages. Post Messages Disabled suppresses most POST messages, such as memory
count, product name, and other non-error text messages. If a POST error occurs, the error is
displayed regardless of the mode selected. To manually switch to Post Messages Enabled during
POST, press any key (except F1 through F12).
●Establish an Ownership Tag, the text of which is displayed each time the system is turned on or
restarted.
●Enter the Asset Tag or property identification number assigned by the company to this computer.
●Enable the power-on password prompt during system restarts (warm boots) as well as during
power-on.
●Establish a setup password that controls access to Computer Setup (F10) Utility and the settings
described in this section.
●Secure integrated I/O functionality, including the serial, USB, or parallel ports, audio, or embedded
NIC, so that they cannot be used until they are unsecured.
●Enable or disable removable media boot ability.
●Solve system configuration errors detected but not automatically fixed during the Power-On Self-
Test (POST).
ENWW Computer Setup (F10) Utilities 1

●Replicate the system setup by saving system configuration information to a USB flash media device
or a diskette-like device (a storage device set to emulate a diskette drive) and restoring it on one
or more computers.
●Execute self-tests on a specified ATA hard drive (when supported by drive).
●Enable or disable DriveLock security (when supported by drive).
Using Computer Setup (F10) Utilities
Computer Setup can be accessed only by turning the computer on or restarting the system. To access
the Computer Setup Utilities menu, complete the following steps:
1. Turn on or restart the computer.
2. As soon as the computer is turned on, press F10 when the monitor light turns green to enter
Computer Setup. Press Enter to bypass the title screen, if necessary.
NOTE: If you do not press F10 at the appropriate time, you must restart the computer and again
press F10 when the monitor light turns green to access the utility.
3. Select your language from the list and press Enter.
4. A choice of five headings appears in the Computer Setup Utilities menu: File, Storage, Security,
Power and Advanced.
5. Use the arrow (left and right) keys to select the appropriate heading. Use the arrow (up and down)
keys to select the option you want, then press Enter. To return to the Computer Setup Utilities
menu, press Esc.
6. To apply and save changes, select File > Save Changes and Exit.
●If you have made changes that you do not want applied, select Ignore Changes and Exit.
●To reset to factory settings or previously saved default settings (some models), select Apply
Defaults and Exit. This option will restore the original factory system defaults.
CAUTION: Do NOT turn the computer power OFF while the ROM is saving the Computer Setup (F10)
changes because the CMOS could become corrupted. It is safe to turn off the computer only after exiting
the F10 Setup screen.
Table 1 Computer Setup (F10) Utility
Heading Table
File Table 2Computer Setup—File on page 3
Storage Table 3Computer Setup—Storage on page 4
Security Table 4Computer Setup—Security on page 6
Power Table 5Computer Setup—Power on page 8
Advanced Table 6Computer Setup—Advanced (for advanced users)
on page 9
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
2 Computer Setup (F10) Utility ENWW

Computer Setup—File
Table 2 Computer Setup—File
Option Description
System Information Lists:
●Product name
●SKU number (some models)
●Processor type/speed/stepping
●Cache size (L1/L2) (dual core processors have this listed twice)
●Installed memory size/speed, number of channels (single or dual) (if applicable)
●Integrated MAC address for embedded, enabled NIC (if applicable)
●System BIOS (includes family name and version)
●Chassis serial number
●Asset tracking number
About Displays copyright notice.
Set Time and Date Allows you to set system time and date.
Flash System ROM
(some models)
Allows you to select a drive containing a new BIOS.
Replicated Setup Save to Removable Media
Saves system configuration, including CMOS, to a USB flash media device or a diskette-like device
(a storage device set to emulate a diskette drive).
Restore from Removable Media
Restores system configuration from a USB flash media device or a diskette-like device.
Default Setup Save Current Settings as Default
Saves the current system configuration settings as the default.
Restore Factory Settings as Default
Restores the factory system configuration settings as the default.
Apply Defaults and
Exit
Applies the currently selected default settings and clears any established passwords.
Ignore Changes
and Exit
Exits Computer Setup without applying or saving any changes.
Save Changes and Exit Saves changes to system configuration or default settings and exits Computer Setup.
ENWW Computer Setup (F10) Utilities 3

Computer Setup—Storage
Table 3 Computer Setup—Storage
Option Description
Device Configuration Lists all installed BIOS-controlled storage devices.
When a device is selected, detailed information and options are displayed. The following options
may be presented.
Hard Disk
●None (prevents BIOS data accesses and disables it as a boot device)
●Hard Disk (treated as hard disk)
Multisector Transfers (ATA disks only)
Specifies how many sectors are transferred per multi-sector PIO operation. Options (subject to
device capabilities) are Disabled, 8, and 16.
Translation Mode (ATA disks only)
Lets you select the translation mode to be used for the device. This enables the BIOS to access
disks partitioned and formatted on other systems and may be necessary for users of older versions
of UNIX (e.g., SCO UNIX version 3.2). Options are Automatic, Bit-Shift, LBA Assisted, User, and
Off.
CAUTION: Ordinarily, the translation mode selected automatically by the BIOS should not be
changed. If the selected translation mode is not compatible with the translation mode that was active
when the disk was partitioned and formatted, the data on the disk will be inaccessible.
Translation Parameters (ATA disks only)
NOTE: This feature appears only when User translation mode is selected.
Allows you to specify the parameters (logical cylinders, heads, and sectors per track) used by the
BIOS to translate disk I/O requests (from the operating system or an application) into terms the hard
drive can accept. Logical cylinders may not exceed 1024. The number of heads may not exceed
256. The number of sectors per track may not exceed 63. These fields are only visible and
changeable when the drive translation mode is set to User.
Default Values IDE/SATA
Allows you to specify the default values for the Multisector Transfers, Transfer Mode, and Translation
Mode for ATA devices.
Storage Options Removable Media Boot
Enables/disables ability to boot the system from removable media.
BIOS DMA Data Transfers
Allows you to control how BIOS disk I/O requests are serviced. When Enable is selected, the BIOS
will service ATA disk read and write requests with DMA data transfers. When Disable is selected,
the BIOS will service ATA disk read and write requests with PIO data transfers.
SATA Emulation
Allows you to choose how the SATA controller and devices are accessed by the operating system.
There are up to two supported options: IDE and RAID.
IDE is the default option. Use this option for "normal" (non-RAID) configurations.
Select the RAID option to enable DOS and boot accesses to RAID volumes. Use this option for RAID
configurations under Windows 2000, XP, or Vista with the appropriate RAID device driver.
4 Computer Setup (F10) Utility ENWW

NOTE: The RAID device driver must be installed prior to attempting to boot from a RAID volume.
If you attempt to boot from a RAID volume without the required device driver installed, the system
will crash (blue screen). Also, do not select the RAID option while the DriveLock feature is enabled
on any attached hard drives. Doing so will cause the DriveLocked drives to remain locked and
inaccessible during subsequent reboots until another SATA Emulation mode is selected.
For more information on RAID, see Redundant Array of Independent Disks (RAID) on dc7700 and
dx7300 Business Desktops Using Intel Matrix Storage Manager at http://www.hp.com/support.
Select your country and language, select See support and troubleshooting information, enter
the model number of the computer, and press Enter. In the Resources category, click Manuals
(guides, supplements, addendums, etc). Under Quick jump to manuals by category, click
White papers.
SATA 0 and 2
Allows you to enable or disable DOS and boot accesses to the Primary channel of the first SATA
controller. This feature only applies when SATA Emulation = IDE.
NOTE: Advanced operating systems like Windows may reenable the channel.
SATA 1 and 3
Allows you to enable or disable DOS and boot accesses to the Secondary channel of the first SATA
controller. This feature only applies when SATA Emulation = IDE.
NOTE: Advanced operating systems like Windows may reenable the channel.
DPS Self-Test Allows you to execute self-tests on ATA hard drives capable of performing the Drive Protection
System (DPS) self-tests.
NOTE: This selection will only appear when at least one drive capable of performing the DPS self-
tests is attached to the system.
Boot Order Allows you to:
●Specify the order in which attached devices (such as a USB flash media device, hard drive,
optical drive, or network interface card) are checked for a bootable operating system image.
Each device on the list may be individually excluded from or included for consideration as a
bootable operating system source.
●Specify the order of attached hard drives. The first hard drive in the order will have priority in
the boot sequence and will be recognized as drive C (if any devices are attached).
NOTE: MS-DOS drive lettering assignments may not apply after a non-MS-DOS operating system
has started.
Shortcut to Temporarily Override Boot Order
To boot one time from a device other than the default device specified in Boot Order, restart the
computer and press F9 when the monitor light turns green. After POST is completed, a list of bootable
devices is displayed. Use the arrow keys to select the preferred bootable device and press Enter.
The computer then boots from the selected non-default device for this one time.
Table 3 Computer Setup—Storage (continued)
ENWW Computer Setup (F10) Utilities 5

Computer Setup—Security
Table 4 Computer Setup—Security
Option Description
Smart Card Options
(some models)
Allows you to enable/disable the Smart Card to be used in place of the Power-On Password.
Setup Password Allows you to set and enable setup (administrator) password.
NOTE: If the setup password is set, it is required to change Computer Setup options, flash the
ROM, and make changes to certain plug and play settings under Windows.
See the Troubleshooting Guide on the Documentation and Diagnostics CD for more information.
Power-On Password Allows you to set and enable power-on password. The power-on password prompt appears after a
power cycle. If the user does not enter the correct power-on password, the unit will not boot.
NOTE: This password does not appear on warm boots , such as Ctrl + Alt + Delete or Restart
from Windows, unless enabled in Password Options, below.
See the Troubleshooting Guide on the Documentation and Diagnostics CD for more information.
Password Options
(This selection appears
only if a power-on
password or setup
password is set.)
Allows you to:
●Lock legacy resources (appears if a setup password is set)
●Enable/disable network server mode (appears if a power-on password is set)
●Specify whether the password is required for warm boot (Ctrl + Alt + Delete) (appears if a power-
on password is set)
●Enable/Disable Setup Browse Mode (appears if a setup password is set) (allows viewing, but
not changing, the F10 Setup Options without entering setup password)
See the Desktop Management Guide on the Documentation and Diagnostics CD for more
information.
Embedded Security
(This menu item only
appears after the
Embedded Security
Device is made available
under Device Security.)
Allows you to:
●Enable/disable the Embedded Security device
●Reset the device to Factory Settings
●Enable/disable power-on authentication support (some models)
●Reset authentication credential (some models)
This feature is supported on some models only. See the Desktop Management Guide on the
Documentation and Diagnostics CD for more information.
Device Security Allows you to set Device Available/Device Hidden for
●Serial ports
●Parallel port
●All USB ports
●Front USB ports
●System audio
●Network controllers (some models)
●Embedded security device (some models)
6 Computer Setup (F10) Utility ENWW

Network Service Boot Enables/disables the computer’s ability to boot from an operating system installed on a network
server. (Feature available on NIC models only; the network controller must be either a PCI expansion
card or embedded on the system board.)
System IDs Allows you to set:
●Asset tag (18-byte identifier) and ownership tag (80-byte identifier displayed during POST).
See the Desktop Management Guide on the Documentation and Diagnostics CD for more
information.
●Ownership Tag. This tag is a string that is displayed under the POST splash screen that may
be used to identify the owner of the computer.
●Chassis serial number or Universal Unique Identifier (UUID) number. The UUID can only be
updated if the current chassis serial number is invalid. (These ID numbers are normally set in
the factory and are used to uniquely identify the system.)
●Keyboard locale setting (for example, U.S. or Deutsch) for System ID entry.
DriveLock Security Allows you to assign or modify a master or user password for hard drives. When this feature is
enabled, the user is prompted to provide one of the DriveLock passwords during POST. If neither
is successfully entered, the hard drive will remain inaccessible until one of the passwords is
successfully provided during a subsequent cold-boot sequence.
NOTE: This selection will only appear when at least one drive that supports the DriveLock feature
is attached to the system.
See the Desktop Management Guide on the Documentation and Diagnostics CD for more
information.
OS Security (some
models)
NOTE: An OS Security selection is in effect only if the processor and operating system being used
comprehend and utilize the security feature.
●Data Execution Prevention (some models) (enable/disable) Helps prevent OS security
breaches.
●OS Management of Embedded Security Device (enable/disable). Enabling this option allows
the OS the ability to manage the Embedded Security Device.
●Reset of Embedded Security Device though OS (enable/disable). A Setup Password is required
to change this setting. Enabling this option allows the OS the ability to reset the Embedded
Security Device back to its factory defaults.
●Virtualization Technology (some models) (enable/disable) Changing this setting requires
turning the computer off and then back on.
Setup Security Level Provides a method to allow end-users limited access to change specified setup options, without
having to know the Setup Password.
This feature allows the administrator the flexibility to protect changes to essential setup options,
while allowing the user to view system settings and configure nonessential options. The administrator
specifies access rights to individual setup options on a case-by-case basis via the Setup Security
Level menu. By default, all setup options are assigned Setup Password, indicating the user must
enter the correct Setup Password during POST to make changes to any of the options. The
administrator may set individual items to None, indicating the user can make changes to the specified
options when setup has been accessed with invalid passwords. The choice, None, is replaced by
Power-On Password if a Power-On Password is enabled.
NOTE: Setup Browse Mode must be set to Enable in order for the user to enter Setup without
knowing the setup password.
Table 4 Computer Setup—Security (continued)
ENWW Computer Setup (F10) Utilities 7

Computer Setup—Power
Table 5 Computer Setup—Power
Option Description
OS Power
Management
●Runtime Power Management— Enable/Disable. Allows certain operating systems to reduce
processor voltage and frequency when the current software load does not require the full
capabilities of the processor.
●ACPI S3 Hard Disk Reset—Enabling this causes the BIOS to ensure hard disks are ready to
accept commands after resuming from S3 before returning control to the operating system.
●ACPI S3 PS2 Mouse Wakeup—Enables or disables waking from S3 due to PS2 mouse activity.
●USB Wake on Device Insertion (some models)—Allows system to wake from Standby on USB
device insertion.
●Unique Sleep Blink Rates—This feature is designed to give the user a visual indication of the
sleep state the system is in. Each sleep state has a unique blink pattern:
◦S0 = Solid green LED.
◦S3 = 3 blinks at 1Hz (50% duty cycle) followed by a pause of 2 seconds (green LED), i.e.,
repeated cycles of 3 blinks and a pause.
◦S4 = 4 blinks at 1Hz (50% duty cycle) followed by a pause of 2 seconds (green LED), i.e.,
repeated cycles of 4 blinks and a pause.
◦S5 = LED is off.
If this feature is disabled, S4 and S5 both have the LED off. S1 (no longer supported) and S3
use 1 blink per second.
Hardware Power
Management
●S5 Maximum Power Savings (some models)—Enable/Disable. Enabling this feature reduces
the power of this system as much as possible in the S5 state. Power is removed from the wake
up circuitry, the expansion slots, and any management features while in S5.
●SATA power management enables or disables SATA bus and/or device power management.
Thermal ●Fan idle mode—This bar graph controls the minimum permitted fan speed.
NOTE: This setting only changes the minimum fan speed. The fans are still automatically
controlled.
8 Computer Setup (F10) Utility ENWW

Computer Setup—Advanced
Table 6 Computer Setup—Advanced (for advanced users)
Option Heading
Power-On Options Allows you to set:
●POST mode (QuickBoot, FullBoot, or FullBoot every 1–30 days).
●POST messages (enable/disable).
●F9 prompt (enable/disable or hidden/displayed). Enabling this feature will display the text F9 =
Boot Menu during POST. Disabling this feature prevents the text from being displayed.
However, pressing F9 will still access the Shortcut Boot [Order] Menu screen. See Storage >
Boot Order for more information.
●F10 prompt (enable/disable or hidden/displayed). Enabling this feature will display the text
F10 = Setup during POST. Disabling this feature prevents the text from being displayed.
However, pressing F10 will still access the Setup screen.
●F11 prompt (hidden/displayed). Setting this feature to displayed will display the text
F11 = Recovery during POST. Hiding this feature prevents the text from being displayed.
However, pressing F11 will still attempt to boot to the HP Backup and Recovery partition. See
Factory Recovery Boot Support for more information.
●F12 prompt (enable/disable or hidden/displayed). Enabling this feature will display the text
F12 = Network during POST. Disabling this feature prevents the text from being displayed.
However, pressing F12 will still force the system to attempt booting from the network.
●Factory Recovery Boot Support (enable/disable). Enabling this feature will cause an additional
prompt, F11 = Recovery, to be displayed during POST on systems with HP Backup and
Recovery software installed and configured with a recovery partition on the boot hard drive.
Pressing F11 causes the system to boot to the recovery partition and launch HP Backup and
Recovery. The F11 = Recovery prompt can be hidden with the F11 prompt (hidden/displayed)
option (see above).
●Option ROM prompt (enable/disable) Enabling this feature will cause the system to display a
message before loading option ROMs. (This feature is supported on some models only.)
●Remote wakeup boot source (remote server/local hard drive).
●After Power Loss (off/on/previous state). If set to Off, the computer remains powered off when
power is restored. If set to On, the computer automatically powers on as soon as power is
restored. If set to Previous State, the computer automatically powers on as soon as power is
restored if it was powered on when power was lost.
NOTE: If you turn off power to the computer using the switch on a power strip, you will not be able
to use the suspend/sleep feature or the Remote Management features.
●POST Delay (None, 5, 10 15, or 20 seconds). Enabling this feature will add a user-specified
delay to the POST process. This delay is sometimes needed for hard disks on some PCI cards
that spin up very slowly, so slowly that they are not ready to boot by the time POST is finished.
The POST delay also gives you more time to select F10 to enter Computer (F10) Setup.
●I/O APIC Mode (some models) (enable/disable). Enabling this feature will allow Microsoft®
Windows Operating Systems to run optimally. This feature must be disabled for certain non-
Microsoft Operating Systems to work properly.
●Hyper-threading (some models) (enable/disable)
●Limit CPUID Maximum Value to 3. Restricts the number of CPUID functions reported by the
microprocessor. Enable this feature if booting to Windows NT.
●Bypass F1 Prompt. This feature allows the system to boot without pressing F1 at the prompt
when the configuration changes.
ENWW Computer Setup (F10) Utilities 9

Execute Memory Test
(some models)
Restarts the computer and executes the POST memory test.
BIOS Power-On Allows you to set the computer to turn on automatically at a time you specify.
Onboard Devices Allows you to set resources for or disable onboard system devices (serial port or parallel port).
PCI Devices ●Lists currently installed PCI devices and their IRQ settings.
●Allows you to reconfigure IRQ settings for these devices or to disable them entirely. These
settings have no effect under an ACPI-based operating system.
PCI VGA Configuration Displayed only if there are one or more PCI graphics controllers in the system and the integrated
video is enabled. Allows you to specify which VGA controller will be the “boot” or primary VGA
controller.
Bus Options On some models, allows you to enable or disable:
●PCI SERR# generation.
●PCI VGA palette snooping, which sets the VGA palette snooping bit in PCI configuration space;
only needed when more than one graphics controller is installed.
Device Options Allows you to set:
●Printer mode (Bi-Directional, EPP + ECP, Output Only).
●Num Lock state at power-on (off/on).
●S5 Wake on LAN (enable/disable).
◦To disable Wake on LAN during the off state (S5), use the arrow (left and right) keys to
set the S5 Wake on LAN feature to Disable. This obtains the lowest power consumption
available on the computer during S5. It does not affect the ability of the computer to Wake
on LAN from suspend or hibernation, but will prevent it from waking from S5 via the
network. It does not affect operation of the network connection while the computer is on.
◦If a network connection is not required, completely disable the network controller (NIC) by
using the arrow (left and right) keys to select the Security > Device Security menu. Set
the Network Controller option to Device Hidden. This prevents the network controller
from being used by the operating system and reduces the power used by the computer
in S5.
●Processor cache (enable/disable).
●Integrated Video (enable/disable) Allows you to use integrated video and PCI Up Solution video
at the same time (available on some models only).
●Internal speaker (some models) (enable/disable) (does not affect external speakers)
●Monitor Tracking (enable/disable). Allows BIOS to save monitor asset information.
●NIC PXE Option ROM Download (enable/disable). The BIOS contains an embedded NIC option
ROM to allow the unit to boot through the network to a PXE server. This is typically used to
download a corporate image to a hard drive. The NIC option ROM takes up memory space
below 1MB commonly referred to as DOS Compatibility Hole (DCH) space. This space is
limited. This F10 option will allow users to disable the downloading of this embedded NIC option
ROM thus giving more DCH space for additional PCI cards which may need option ROM space.
The default will be to have the NIC option-ROM-enabled.
Table 6 Computer Setup—Advanced (for advanced users) (continued)
10 Computer Setup (F10) Utility ENWW

Recovering the Configuration Settings
This method of recovery requires that you first perform the Save to Removable Media command with
the Computer Setup (F10) Utility before Restore is needed. (See Save to Removable Media
on page 3in the Computer Setup—File table.)
NOTE: It is recommended that you save any modified computer configuration settings to a a USB
flash media device or a diskette-like device (a storage device set to emulate a diskette drive) and save
the diskette or device for possible future use.
To restore the configuration, insert the USB flash media device or a diskette-like device (a storage device
set to emulate a diskette drive) with the saved configuration and perform the Restore from Removable
Media command with the Computer Setup (F10) Utility. (See Restore from Removable Media
on page 3in the Computer Setup—File table.)
ENWW Recovering the Configuration Settings 11