HP V185E User manual

v185e/v185es
/
v185w/v185ws
/
w185
/
W185q LCD
Monitor User’s Guide

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or
editorial errors or omissions contained herein.
HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP.
This document contains proprietary information that is protected by copyright. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent of HP.
Hewlett-Packard Company
10955 Tantau Avenue
Cupertino, CA 95014-0770
USA
Copyright © 2009 Hewlett-Packard Development Company, L.P.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited pay-
per-view viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.
HP supports lawful use of technology and does not endorse or encourage the use of its products for purposes other than those
permitted by copyright law.
The information in this document is subject to change without notice.

Preface
About This Guide
This guide is intended for anyone who uses the v185e / v185es / v185w / v185ws / w185 / W185q LCD Monitor. It
describes the monitor’s features, setup, and operation.
The sections are as follows:
ySafety and Maintenance Guidelines
ySetup
yUsing the Monitor
yInstalling Drivers and Using the Auto-Adjustment Feature
yTechnical Support FAQs
ySpecifications
yLCD Monitor Quality and Pixel Policy
yAgency Regulatory Notices
Notational Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These
blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your monitor.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data, and tells you how to
avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific
presentation of the warning is mandated by regulatory authority.
3

Safety and Maintenance Guidelines
Important Safety Information
The power cord is designed for use with your monitor. To use a different cord, use only a power source and
connection compatible with this monitor. For information on the correct power cord set to use with your monitor, see
Power Cord Set Requirements.
WARNING: To reduce the risk of electric shock or damage to your equipment, do not disable the power cord
grounding feature. The grounding plug is an important safety feature. Connect the equipment to a grounded
(earthed) power outlet.
For your safety, be sure that the grounded power outlet you plug the power cord into is easily accessible to
the operator and located as close to the equipment as possible. To disconnect power from the equipment,
unplug the power cord from the power outlet by grasping the plug firmly. Never pull on the cord.
Before connecting cables, disconnect power from the monitor by unplugging the power cord from the
electrical outlet.
Do not place anything on power cords or cables. Arrange them so that no one can accidentally step on or trip
over them. Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord by its
plug.
CAUTION: To protect your monitor, as well as your computer, connect all power cords for your computer and
its peripheral devices (such as a monitor, printer, or scanner) to a surge protection device such as a power
strip with surge protection or uninterruptible power supply (UPS).
Not all power strips provide surge protection; the power strips must be specifically labeled as having this
ability. Use a power strip whose manufacturer offers a damage replacement policy so you can replace your
equipment if surge protection fails.
Safety Precautions
CAUTION: Avoid applying pressure to the LCD screen; doing so can cause damage.
yUse only a power source and connection compatible with this monitor, as indicated on the label/back plate
of the monitor.
yBe sure the total ampere rating of the products connected to the outlet does not exceed the current rating
of the electrical outlet, and the total ampere rating of the products connected to the cord does not exceed
the rating of the cord. Look on the power label to determine the ampere rating (Amps or A) for each device.
4

yInstall your monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug
firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
yDo not allow anything to rest on the power cord. Do not walk on the cord.
Maintenance Guidelines
To enhance the performance and extend the life of your monitor:
yDo not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating
properly or has been dropped or damaged, contact your HP authorized dealer, reseller, or service provider.
yAdjust only those controls that are described in the operating instructions.
yTurn your monitor off when not in use. You can substantially increase the life expectancy of your monitor by using a
screen saver and turning off the monitor when not in use.
yKeep your monitor in a well-ventilated area, away from excessive light, heat, or moisture.
ySlots and openings in the cabinet are provided for ventilation. These openings must not be blocked or
covered. Never push objects of any kind into cabinet slots or other openings.
yUnplug your monitor from the wall outlet before cleaning.
yDo not drop your monitor or place it on an unstable surface.
yWhen removing the monitor pedestal base, you must lay the monitor face down on a soft area to prevent it from
getting scratched, defaced, or broken.
Cleaning the Monitor
The monitor is a high-quality optical device that requires special care when cleaning. To clean the monitor, follow
these steps:
1 Turn off the computer and the monitor.
2 Unplug your monitor from the wall outlet before cleaning.
CAUTION: Do not use benzene, thinner, ammonia, or any volatile substances to clean the monitor screen or
cabinet. These chemicals may damage the monitor. Do not use liquid cleaners or aerosol cleaners. Never use
water to clean an LCD screen.
3 Wipe the screen with a dry, soft, clean cloth.
•If the screen requires additional cleaning, use an antistatic screen cleaner.
4 Dust the monitor housing. Use a damp cloth to clean the cabinet.
•If the cabinet requires additional cleaning, use a clean cloth dampened with isopropyl alcohol.
5 Plug in the monitor.
6 Turn on the monitor and the computer.
5

Setup
Base and Tilt
Attaching the Base
1 Set the panel face down on a flat , protected surface , such as a table top.
2 Using both hands , align the base with the pedestal and push in firmly to lock in place.
Make sure that the base is securely locked in place before continuing with the setup procedure.
CAUTION: To prevent damage, avoid applying pressure to the panel front.
6

Removing the Base
1 Set the panel face-down on a flat, protected surface.
2 Squeeze the tabs in the bottom of the base to release the lock.
3 Remove the base from the pedestal.
CAUTION: To prevent damage, avoid applying pressure to the panel front.
Adjusting the Tilt
For optimal viewing, adjust the screen tilt to your own preference, as follows:
1 Face the front of the monitor and hold the stand so that you do not topple the monitor while changing the tilt.
2 Adjust the tilt by moving the monitor’s top edge toward or away from you.
CAUTION: To avoid breakage or other damage, do not touch the LCD screen while changing the tilt.
7

Cables
Attaching the Cables
1 Turn off your computer.
2 If you are attaching a VGAcable, connect one end of the 15-pin D-Sub VGA cable (blue connector) to the back of
the monitor and connect the other end to the computer VGA port.
3 If attaching a DVI cable, connect one end of the cable to the back of the monitor and connect the other end to the
computer.
8

4 Connect one end of the power cord to the back of the monitor and plug the other end into a grounded outlet.
5 Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image,
see Technical Support FAQs and Using the Monitor.
9

Wall Mounting Arm
Preparing to Install a Wall Mounting Arm (Not supplied)
This monitor can be attached to a wall mounting arm that you purchase separately.
CAUTION: Before disassembling the monitor, turn off the monitor power, and disconnect all power, video, and
audio cables.
1 Disconnect the cables from the monitor.
2 With the panel face-down on a protected surface, remove the screws and the pedestal/base attachment.
3 Follow the manufacturer’s instructions to assemble the wall mounting arm.
Installing a Wall Mounting Arm
1 Set the monitor screen down on a flat, soft, protected surface.
2 Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the mounting holes in
the back of the monitor.
3 Insert four screws into the mounting holes and tighten.
4 Reconnect the cables. Refer to the user’s manual that came with the wall mounting arm (purchased separately)
for instructions on attaching it to the wall.
10

Using the Monitor
Operating Instructions
Control buttons are located on the front of the panel, as shown below. Use the Menu button (B) to adjust the display
settings to your personal preferences:
ySet up the monitor, attach the cables, and adjust the tilt as described in the Setup section above.
yPress the Power button (E) to turn the monitor on and off. The power indicator lights up when the monitor is on.
yThe monitor must be turned on for the other control buttons to work.
ySet the resolution (Setting the Optimal Resolution) and adjust the volume (Adjusting the Volume).
yAdjust the onscreen display (OSD) settings (Adjusting On-screen Display Settings).
11

External Controls
A Auto button Automatically fine-tunes the image quality.
B Menu button Opens, selects, or exits the OSD menu.
C – (minus) button Navigates backward through the OSD menu and decreases adjustment levels.
If the OSD menu is inactive, activates the Volume decrease.
D + (plus) button Navigates forward through the OSD menu and increases adjustment levels.
If the OSD menu is inactive, activates the Volume increase.
E Power button Turns the monitor on or off.
F Power LED Fully powered = green
Sleep mode = amber
Sleep timer mode = flashing amber
See Technical Support FAQs for more information.
12

Settings
Setting the Optimal Resolution
The recommended resolution for this monitor is 1366 x 768.To configure the monitor to this resolution, complete the
setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the
following:
1 Click the Windows Start Button®, and then click Control Panel.
2 Under Appearance and Personalization, click Adjust Screen Resolution.
3 Set the resolution slide bar to 1366 x 768.
NOTE: If 1366 x 768 is not shown, download the monitor driver from the Web. See Using the Monitor for instructions.
Adjusting the Volume
While the monitor is turned on but the OSD menu is inactive, press the volume increase and decrease (plus and
minus) buttons to adjust volume to the desired level. Volume can range from 0 (mute) to 100. The preset value is 50.
Locking and Unlocking the OSD
To change the lock status of the on-screen display (from locked to unlocked, or from unlocked to locked) press and
hold the Menu button for 10 seconds while the monitor is on. If the OSD is locked, the message “OSD Lock” displays
for 10 seconds.
13

Adjusting On-Screen Display Settings
Use the OSD menu to adjust the screen image and change settings. To access the OSD menu:
1 If the monitor is not already on, press the Power button to turn the monitor on.
2 Press the Menu button to activate the OSD menu.
3 Press the – (minus) and + (plus) buttons to navigate through the functions. Once the desired function is
highlighted, press the Menu button again to activate it. If the selected function has a sub-menu, it displays.
Press – (minus) or + (plus) again to navigate through the sub-menu functions. Once the desired sub-function is
highlighted, press the Menu button to activate it.
4 Press – (minus) or + (plus) to change the settings of the selected function.
5 To exit and save, select the Exit function. If you want to adjust another function, repeat steps 3–4.
NOTE: If the buttons remain untouched for 30 seconds while displaying a menu, new adjustments will be saved and
exit the menu.
14

OSD Menu
The table below shows the OSD menus and their functions at each level.
OSD Menu Levels
Level 1 Level 2 Level 3 Level 4 Factory Preset
Switch Video Input
(w185 / W185q only)
Brightness Adjustment Scale Y
Reset
Cancel
Save and Return
Contrast Adjustment Scale Y
Reset
Cancel
Save and Return
Image Control Auto Adjustment “Adjusting” Message Y
Horizontal Position Adjustment Scale Y
Vertical Position Adjustment Scale Y
Custom Scaling
Fill to Screen
Fill to Aspect Ratio
Clock Adjustment Scale Y
Clock Phase Adjustment Scale Y
Cancel
Save and Return
Color 9300 K
6500 K Y
Custom Color
Custom Color
Adjustment
Reset
Cancel
Save and Return
sRGB
Reset
Cancel
Save and Return
15

OSD Menu Levels (continued)
Level 1 Level 2 Level 3 Level 4 Factory Preset
Quick View Movie
Photo
Gaming
Text Y
Custom
Cancel
Save and Return
Language Deutsch
简体中文
日本語
English English
Español
Français
Italiano
Nederlands
Cancel
Save and Return
Volume(w185 only)
OSD
Control(w185 only) Horizontal OSD Position Adjustment Scale Y
Vertical
OSD Position Adjustment Scale Y
OSD Transparency Adjustment Scale Y
OSD Timeout Adjustment Scale Y
Cancel
Management Power Saver Save and Return Y
Mode Display On / Off Selection Y
Power-On
Status Display On / Off Selection Y
DDC/CI Support On / Off Selection Y
Bezel Power LED On / Off Selection Y
Sleep Timer Timer Set Menu Y
Default Video Input
(w185 / W185q only) Analog-VGA Digital-DVI Y
16

OSD Menu Levels (continued)
Level 1 Level 2 Level 3 Level 4 Factory Preset
Cancel
Save and Return
OSD Control
(v185w only) Horizontal OSD Position Adjustment Scale Y
Vertical OSD
Position Adjustment Scale Y
OSD Transparency Adjustment Scale Y
OSD Timeout Adjustment Scale Y
Cancel
Save and Return
Information
Factory Reset Yes
No
Exit
17

Installing Drivers and Using the Auto-Adjustment Feature
Downloading Drivers and Software
To download the latest version of drivers and software files from the HP Support Web site:
1 Refer to: http://www.hp.com/support
2 Select your country/region.
3 Select Download Drivers and Software.
4 Enter the model number of your monitor. The software download pages for your monitor will be displayed.
5 Download and install the driver and software files using the instructions in the download pages.
Using the Auto-Adjustment Function
Press the Auto button to optimize the screen performance for VGA (analog).
If your monitor is using VGA (analog) input, auto-adjustment can correct the following image quality conditions:
yFuzzy or unclear focus
yGhosting, streaking, or shadowing effects
yFaint vertical bars
yThin, horizontal scrolling lines
yAn off-center picture
18

Technical Support FAQs
Technical Support FAQs (Frequently Asked Questions)
Problem & Question Possible Solutions
Power LED is not on. yMake sure the Power button is on and the power cord is properly
connected to a grounded power outlet and to the monitor.
No Plug & Play. yIn order for the Plug & Play feature of the monitor to work, you need a
Plug & Play compatible computer and video card. Check with your
computer manufacturer.
yCheck the monitor’s video cable and make sure none of the pins are
bent.
yMake sure the HP monitor drivers are installed (HP monitor drivers are
available at: http://www.hp.com/support)
Picture is fuzzy and has ghosting
shadowing problem. yAdjust the contrast and brightness controls.
yMake sure you are not using an extension cable or switch box. We
recommend plugging the monitor directly into the video card output
connector on the back of your computer.
yFor VGA input, the auto-adjustment function may fix this problem.
Picture bounces, flickers or wave
pattern is present in the picture. yMove electrical devices that may cause electrical interference as far away from the monitor as possible.
yUse the maximum refresh rate your monitor is capable of at the
resolution you are using.
Monitor is stuck in “Active Off-Mode”. yThe computer power switch should be in the on position.
yThe computer video card should be snugly seated in its slot.
yMake sure the monitor’s video cable is properly connected to the
computer.
yInspect the monitor’s video cable and make sure none of the pins are
bent.
yMake sure your computer is operational by hitting the Caps Lock key
on the keyboard while observing the Caps Lock LED. The LED should
either turn on or off after hitting the Caps Lock key.
19

Technical Support FAQs (Frequently Asked Questions) (continued)
Problem & Question Possible Solutions
Missing one of the primary colors (red,
green, or blue). yInspect the monitor’s video cable and make sure that none of the pins are bent.
yMake sure the monitor’s video cable is properly connected to the
computer.
Screen image is not centered or sized
properly. yAdjust horizontal and vertical screen position.
yFor VGA input, the auto-adjustment function may fix this problem.
Picture has color defects (white does
not look white). yAdjust RGB color or select color temperature.
Unable to set the monitor to the
optimal resolution. yMake sure that the graphics card supports the optimal resolution (1366 x 768).
yMake sure that the latest supported driver is installed for the graphics
card. For HP and Compaq systems, you can download the latest
graphics driver for your system from:
http://www.hp.com/support
yFor other systems, refer to the Web site for your graphics card.
20