HP Proliant DL580 User manual

HP 3-7U Quick Deploy
Rail System
Installation Instructions
for HP products
© Copyright 2005-2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should
be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
June 2006 (Third Edition)
Part Number 378950-003
Overview
This rack hardware kit supports a variety of 3-7U HP products
in round-, square-, or threaded-hole racks. Use the legend to
identify installation steps appropriate to the type of rack.
IMPORTANT: If you are shipping the server installed
in a rack, see the additional instructions located in
"Preparing the product for rack relocation or
integrated shipping" before proceeding.
Hardware kit contents
In addition to the supplied items, you may need:
•Screws that fit a threaded-hole rack
•The appropriate screwdriver for the screws
•Kit 371482-B21 for integrated shipping a
round-hole rack
Rack warnings
WARNING: To reduce the risk of personal
injury or damage to the equipment,
be sure that:
•The leveling jacks are extended to
the floor.

•The full weight of the rack rests on the
leveling jacks.
•The stabilizing feet are attached to the
rack if it is a single-rack installation.
•The racks are coupled together in
multiple-rack installations.
•Only one component is extended at a
time. A rack may become unstable if
more than one component is extended
for any reason.
Anti-tip stabilizer
The anti-tip stabilizers provide stability and support when
equipment is installed, removed or accessed within the rack.
Stabilizer kits are available in both 600-mm and 800-mm
versions. HP also recommends using the side feet, provided
with these kits, to stabilize stand-alone racks from the other
side. If you are stabilizing racks that are secured together
with baying kits, the side feet are optional on either end
of the row.
HP recommends that stabilizer option kits be used when one
or more of the following situations occur:
•The standard 600-mm (23.62-in) or 800-mm (31.50-in)
front foot is required with deployments of
stand-alone racks.
•Side feet, which are included in the stabilizer kits, are
recommended to be installed as well.
Rack rows with four or more bayed racks, without a single
rack-mountable components exceeding 99.79 kg (220 lb), do
not need a stabilizer kit installed.
Lift
WARNING: If you are going to use a lift, be
sure to use a lift that can handle the load of
the server.
Installing the product in a rack
CAUTION: Always plan the rack installation so that
the heaviest item is on the bottom of the rack. Install
the heaviest item first, and continue to populate the
rack from the bottom to the top.
IMPORTANT: If you are shipping the server installed
in a rack, see the additional instructions located in
"Preparing the product for rack relocation or
integrated shipping" before proceeding.

IMPORTANT: If you are installing the server in a
shallow rack [i.e., less than 72.39 cm (28.5 in)], see
the additional instructions located in "Preparing the
rails for shallow rack installation" before proceeding.

WARNING: To reduce the risk of personal
injury or equipment damage, be sure that
the rack is adequately stabilized before
sliding the server into the rails.
WARNING: To reduce the risk of personal
injury or equipment damage, do one of
the following:
•Use two or more people to lift and
stabilize the product pieces
during assembly.
•Use a lift that can handle the load
of the product.

CAUTION: Be sure to keep the product parallel to
the floor when sliding the server into the rails.
Tilting the product up or down could result in
damage to the slides.
Installing the cable
management arm
IMPORTANT: If you need to hinge the cable
management arm on the rear right-hand side of the
rack, see the instructions located in "Converting the
cable management arm swing" and perform the steps
to convert the arm to a right-hand swing before
installing the arm on the rack. After conversion,
mirror the installation steps on the rear right-hand
side of the rack.

NOTE: When properly installed, the cable
management arm is attached to the server and the
rack rail.
The installation is complete.
If the rack installation is to be shipped with product(s)
installed, perform the steps in "Preparing the product for rack
relocation or integrated shipping."
Converting the cable
management arm swing
The cable management arm is designed for ambidextrous
implementation. You can convert the arm for
right-hand swing.
NOTE: To access some components on the rear of the
product, you may need to remove the cable
management arm.

IMPORTANT: When converting the cable arm,
always be sure to orient the arm with the cable trough
facing upward.
The cable management arm is ready for installation on
the rack.
Preparing the rails for
integrated shipping in a rack
IMPORTANT: You must provide screws to secure
the slide mounting bracket assemblies in a
threaded-hole rack.

IMPORTANT: You will need kit 371482-B21 to
prepare a round-hole rack for integrated shipping.
NOTE: Use the integrated shipping hardware
included with this kit to prepare a square-hole rack for
integrated shipping.

Return to step 1 in "Installing the product in a rack."
Preparing the product for
rack relocation or
integrated shipping
To service or remove the product from the rack, reverse the
procedures in this section:
1. Remove the rear slide locking screw and the front rail
locking screws. Retain the screws for future use.
2. Cut and discard the orange tie wraps.

Preparing the rails for shallow
rack installation
Return to step 2 in "Installing the product in a rack."