hq telecom HQTBTA340 User manual

Bluetooth Phone Adapter User Manual (Model HQTBTA340)
1. LED indicator
2. Pair button
3. Ringer (ON/OFF) switch
4. Mini USB DC jack
5. LINE jack
6. TELEPHONE Jack
Packing Content:
(1) Bluetooth phone adapter
(1) Extension cord
(1) Power adapter
(1) User manual
Overview of Bluetooth Phone Adapter
The Bluetooth phone adapter connects to your traditional non-Bluetooth
telephone line and allows you to answer PSTN calls using your remote Bluetooth
device (Bluetooth headset). With the Bluetooth phone adapter, you can enjoy
the comfort and convenience of hands-free communication.
SETUP / INSTALLATION:
Connecting the phone adapter with your telephone
1. Plug one end of the telephone cord into the "LINE" jack of the Bluetooth phone
adapter and the other end into the wall jack.
2. Plug one end of the extension cord into the "TELEPHONE" jack of the Bluetooth
phone adapter and the other end into your telephone itself.

Powering on the Bluetooth phone adapter
1. Connect one end of the power adapter to the mini USB DC jack of the
Bluetooth phone adapter.
2. Connect the other end of the power adapter to a wall outlet (wall socket).
Pairing the Bluetooth phone adapter and your Bluetooth headset
The Bluetooth phone adapter can support the following PINs: 0000, 1234, 6666,
and 8888. To know what PIN your Bluetooth headset adopts, please refer to its
user guide. If the PIN of your Bluetooth headset is none of the four defaults,
please consult your headset manual to see if you can change it to one of the
supported PINs.
If the PIN of your Bluetooth headset is one of the PINs supported, please follow
the steps below to pair the Bluetooth phone adapter with your Bluetooth
headset.
1. Put your Bluetooth headset into the pairing mode by following the instructions
in its user guide.
2. Press and hold the Pair button of the Bluetooth phone adapter for 3 seconds,
until you see the LED indicator flashes quickly. Next, the Bluetooth phone adapter
will attempt to pair and connect with your Bluetooth headset automatically.
Note: In some cases, the pairing process can take up to 2 minutes.
3. If paired was successful, the LED indicator on the Bluetooth phone adapter will
flash every second (as shown in the LED indicator chart below). If pairing fails (LED
light flashing every 3 seconds (idle mode), then repeat the steps above.
Using the phone adapter to answer PSTN calls
Once the Bluetooth phone adapter is connected to your Bluetooth headset, you
can use the Bluetooth headset by pressing its Talk button to receive or end a
PSTN call.
You can also use your telephone to receive and answer PSTN calls as usual.

You may adjust the “Ringer” switch to let the phone adapter ring or not according
to your interest.
LED indicator chart
LED indicator Phone adapter
Status
Flashing once every three seconds
Idle mode (Powered on)
Flashing once every one second
Pairing mode
Flashing twice every three seconds
Connected mode
Flashing five times every one second
A call incoming
On (steadily)
Call active mode
Pairing additional devices
Your Bluetooth phone adapter can store pairing information for up to eight
different headsets equipped with Bluetooth wireless technology. If you want to
pair the phone adapter and more than one headset, please follow the pairing
process to pair them one by one, as shown above. Headset information is stored
in a “Paired Device List” in memory in chronological order. When an attempt to
pair with more than eight headsets is made, the oldest paired headset will be
removed from the list. Any of the eight paired headsets can initiate a paired
connection to the Bluetooth phone adapter while the phone adapter is in the idle
mode. The Bluetooth phone adapter will automatically initiate a paired
connection (when powered on) with the last headset it was connected to.
When there is an incoming call, the Bluetooth phone adapter can also connect the
latest connected headset automatically even if the Bluetooth phone adapter is in
“idle”mode (not paired to any headset). In case the connection is lost, you can
manually connect the phone adapter to the headset by pressing the Pair button
(2).
For additional questions on this Bluetooth phone adapter, please visit
https://hqtelecom.com.