Huddly HD-PGDE-0108-A1 User manual
1
Huddly USB to
PoE Adapter
Product and Compliance
Information
HD-PGDE-0108-A1
Valid for H3BA
2
Contents
Safety and Caution Information 3
Temperature 3
Modify 3
User Instructions 4
Installation 4
Power 4
Regulatory Compliance Information 6
Canada 6
Industry Canada statement
United States
FCC compliance statement 6-7
Australia and New Zealand 7
European Union 8
EU Single
Point of Contact
European Union EMC
Directive conformance statement
Support 9
EULA 9
Privacy policy 9
3
Safety and Caution
Information
Temperature
is device is intended for use in ambient temperatures
between 0 °C and 35 °C (32 °F and 95 °F). Avoid using or
storing next to heat sources, in direct sunlight, or outside
the intended temperature ranges.
Modify
Modication to thermal solution, device components or
enclosure shall violate regulatory compliance requirements
and may induce safety hazards.
4
User Instructions
The USB to PoE Adapter is made to easily connect an
Ethernet device to a host computer using USB-C. e USB
to PoE Adapter can also provide 37-57V DC power to a con-
nected Ethernet device. Power to the Adapter is provided
from the USB host or the included 5V DC adapter.
Installation
Connect the Ethernet device and the USB to PoE Adapter
using minimum a Cat5e rated Ethernet cable. Further connect
the USB to PoE Adapter to a USB host.
e status LED will light up when the USB is connected. If the
LED is white, the Adapter has sucient power. Otherwise, if
the status LED is red, connect the included power adapter.
A wall mount bracket with double sided tape is included.
To install the bracket, remove the tape liner and place the
bracket in a suitable position, not higher than 2m, and on a
clean smooth surface.
Aach the USB to PoE Adapter to the wall mount bracket and
ensure that the unit is properly locked in position around the
mounting plate. Magnetic surfaces can generally be used to
mount the USB to PoE Adapter. Optionally, place the Adapter
directly on any horizontal surface.
e USB to PoE Adapter wall bracket is designed to hold
Huddly the USB to PoE Adapter only. It should not be used
as support for any additional weight.
5
Power
Input
Minimum requirements:
USB VBUS 5V >0.5A
e USB to PoE Adapter will enable Power over Ethernet
functionality when the following input requirements are met.
USB host 5V 3A, or external
DC adapter 5V 4A
e LED will light up white when these
power conditions are met.
Use only the included Mean Well SGA25I05-P3BHD or
Cincon TRE25R050-35G02 VI AC/DC adapter.
Other AC/DC adapters are not supported
Output
Voltage range: 37-57V DC
Maximum current: 0.35A
Recycling
At the end of life for this product, local rules and regulations
shall be followed. is product is ment to be recycled, and if
applicable and/or possible, should be handed in to a collection
point for recycling purposes.
6
Regulatory Compliance
Information
is product is cNus marked in accordance with
the requirements of the applicable standards
for Canada and the United States.
Canada
Industry Canada statement
is Class A digital apparatus complies with CAN ICES-3
(A)/NMB-3(A).
Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device
must accept any interference, including interference that
may cause undesired operation of the device.
United States
FCC compliance statement
is device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation.
7
is is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may
be required to take adequate measures.
Australia and New Zealand
Note: is equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. ese limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. is
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Changes or modications to the equipment not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
8
In the European Union, this symbol indicates
that this product must not be disposed of with
household waste. It is your responsibility to hand
it over to a designated collection point for the
recycling of waste electronic equipment. For
more information, please contact your local waste
collection center or the point of purchase of this
product.
European Union
EU Single Point of Contact
Huddly AS,
An: Compliance
Karenslyst allé 51
0279 Oslo, Norway
European Union EMC Directive conformance statement
This product has been tested and found to
comply with the limits for Class A equipment
according to European Standards harmonised in
the Directives in compliance. e limits for Class
A equipment were derived for commercial and
industrial environments to provide reasonable
protection against interference with licensed
communi-cation equipment.
Warning: is is a Class A product. In a domestic environment
this product may cause radio interference, in which case the
user may be required to take adequate measures.
9
Support
For more information visit:
www.huddly.com/support
EULA
By using this product, you agree that your use of this product is
subject to our End User Licence Agreement terms available at:
www.huddly.com/eula
Privacy policy
Our privacy policy is available at:
www.huddly.com/privacy-policy
You can nd further compliance information at:
www.huddly.com/L1/compliance
Table of contents
Other Huddly Adapter manuals
