Hunter 44156 User manual

1
Form# 44042-01
20100224
©2010 Hunter Fan Co.
Set & $aveSet & $aveSet & $ave
Installation and
Operation manual
Model
44156W
Programmable Thermostat
English

2

3

Important Information....................................... 5
Tools ................................................................ 6
Uninstalling the Existing Unit ........................... 7
Installing the Thermostat ............................... 12
installing the wall plate ................................ 12
connecting the wires ................................... 16
attaching the thermostat ............................. 18
Settings ......................................................... 22
Methods of Operation ................................... 26
manual operation ........................................ 28
default programs ......................................... 32
creating custom programs .......................... 34
Icons and Features ....................................... 38
Wiring Diagrams.............................................49
Troubleshooting ............................................ 52
Warranty.........................................................55

4

Thank you for choosing a Hunter programmable
thermostat. Your new Hunter thermostat will
provide years of reliable service and year-round
energy savings.
Please read this manual before beginning
installation and save this booklet for complete
operation instructions.

Programmable Thermostat


Programmable Thermostat


5
This thermostat is designed to work on the following
heating and cooling systems:
Gas – Standing Pilot
Gas – Electronic Ignition
Gas – Fired Boilers
Gas – Milivolt Systems
Oil – Fired Boilers
Oil – Fired Furnace
Electric Furnace
Electric Air Conditioning
Single Stage Heat Pump - No auxilary
This thermostat is not designed for multi-stage heat
pump systems or 110/220 V baseboard heating
systems.
If you are unsure what kind of heating and cooling
system you have, please contact a qualied HVAC
Technician for assistance.


6
This thermostat includes two #8 slotted screws
and two wall anchors for mounting.
To install your new thermostat, you will need the
following supplies:
Flat-head screwdriver
....................................................................................
Small Phillips-head screwdriver
....................................................................................
Hammer
....................................................................................
Electric drill and 3/16” bit
....................................................................................
Two 1.5 Volt (AA) size alkaline batteries
....................................................................................


7







8
Y
RC
G
W
Y
RC
G
W

9
1. Turn the system power OFF from the existing
thermostat. Turn the power to the HVAC
system OFF at the main power panel or at
the furnace.
2. Remove the existing thermostat cover to
access the wires from the wall.
(Some thermostats may have multiple covers, screws
or other locking devices that must be removed or
disengaged.)
3. Locate, but do not disconnect the wires.
(If wires are not visible, they may be connected to the
back of the wall plate. Some models may have doors
that open to expose the wires and mounting screws.)


10
G RC RH Y W
if your existing
thermostat is marked...
label the wire
with this sticker:
G / F
G
G
W / H / B
W/B
W/B
Y / C* / M / O
Y/0
Y/0
RC / VC
RC
RC
RH / R / VR / 4
RH
RH
24 Volt
24 Volt cool
air conditioning
compressor
heating
fan
Y1
Y1
Y1
heat pump
compressor

11
4. Using the provided stickers, label each wire
according to the chart.
(If the terminals are not labeled, contact
a qualied HVAC technician.)




*If wires marked Y & C are both present, C may
be a Common wire and should not be used. If
you have a wire marked C, do not connect it
to any terminal. This wire is used only for non-
battery powered thermostats.
5. Do not let the wires slip back into the
wall during disconnection. You may want
to secure the wires to the wall as you
disconnect them. After all wires are labeled,
disconnect each wire and remove the
existing wall plate.

Y
RC
G
W
W

12
W
RC
Y
G

13


1. Remove the wall plate from the new
thermostat by pressing the release tab on the
bottom of the thermostat.
2. Position the new wall plate on the wall and
pull the labeled wires through the opening.
3. If the existing holes do not match those
on the Hunter wall plate, or if there are no
existing holes, visually level the wall plate
and mark the wall for two holes.

14
W
RC
Y
G

15
4. Remove the wall plate and drill two 3/16”
holes where marked.
5. Tap the plastic anchors into the holes until
they are ush with the wall.
6. Reposition the wall plate on the wall, pulling
the wires through the opening. Insert the
mounting screws through the wall plate and
into the anchors. Verify that the wall plate
is visually level and securely tighten both
screws.


16
GRCRHY/0W/B
RC
G
Y1
Y/0
W/B
Y1
Terminal Shield

17


1. Loosen, but do not remove, the terminal
screws.







2. Match and connect the wires from the wall
to the terminals as shown. Wires should be
inserted behind the black terminal shields.
Tighten each screw after the connection has
been made.
(The ends of any extra wires should be wrapped in
electrical tape and carefully pushed back into the wall.)
3. Push any excess wire length back into the
wall to prevent interference.
G RC RH Y W
Jumper

18
DISABLE
ENABLE
RECOVERY
HG
HE
W/B Y/O RH RC G
SYSTEM TYPE
STD HP
Y1 FAN OPTION
AM
HEAT
4
T
Thermostat
Cover
System
Switch
G RC RH Y/O W/B Y1

19

Lift the thermostat cover and set the SYSTEM  to OFF
and the FAN switch to AUTO.
1. Locate the HE/HG  on the back of the thermostat.
Set the switch to HG (default) for gas furnace and oil
burners. Set the switch to HE for electric furnaces.
(The switch has no effect when the system is set to
cooling mode.)
2. Locate the Auto Recovery switch on the back of the
thermostat. If you wish to use the Auto Recovery
feature, verify that the switch is in the ENABLE position.
If you do not wish to use this feature, simply change the
switch to the DISABLE position. See pages 44-45 for
more information.
3. System type - Locate the
SyStem type
switch on the
back of the thermostat. Select either STD (Standard) or
HP (Heat Pump) to match your system.


20
1
2
Tab