Husqvarna AUTOMOWER 210 C User manual

HUSQVARNA AUTOMOWE R™
210 C
OPER ATOR’S MAN UAL

TABLE OF CONTENTS
English - 3
1. Introduction and safety .............................................................. 5
1.1 Introduction ..................................................................................... 5
1.2 Symbols on Automower™ ........................................................ 6
1.3 Symbols in the Operator’s Manual .......................................... 7
1.4 Safety instructions ........................................................................ 8
2. Presentation .................................................................................. 10
2.1 Automower™, what’s what? .................................................. 11
2.2 Function of Automower™ ........................................................ 12
2.3 One Automower™ in several gardens ................................. 15
3. Installation ..................................................................................... 16
3.1 Preparations ................................................................................. 17
3.2 Installation of the loop generator/charger .......................... 17
3.3 Charging the battery .................................................................. 18
3.4 Installation of the boundary wire ........................................... 19
3.5 Connecting the boundary wire .............................................. 26
3.6 Checking the installation ......................................................... 27
3.7 Linking the Automower™ to the loop generator/charger 27
4. Use .................................................................................................... 28
4.1 Starting Automower™ ............................................................... 28
4.2 Stopping Automower™ ............................................................. 28
4.3 Restart ............................................................................................ 29
4.4 Switching off Automower™ ..................................................... 29
4.5 Using the Timer ........................................................................... 29
4.6 Adjusting the cutting height ..................................................... 30
4.7 Changing the PIN code ............................................................. 31
4.8 Charging and storage between mowing .............................. 31
4.9 Sounds ........................................................................................... 32
5. Control panel ................................................................................ 33
5.1 Select .............................................................................................. 33
5.2 Numbers ........................................................................................ 33
5.3 Main switch ................................................................................... 34
5.4 Indicator lamps ............................................................................ 34
6. Garden example .......................................................................... 35
7. Maintenance .................................................................................. 37
7.1 Battery ............................................................................................ 37
7.2 Winter storage ............................................................................. 38
7.3 Service ........................................................................................... 38
7.4 Cleaning ......................................................................................... 39
7.5 Replacing the blades ................................................................ 40
8. Trouble shooting ........................................................................ 42
8.1 Fault messages ........................................................................... 42
8.2 Fault symptom ............................................................................. 45
9. Technical data .............................................................................. 46
10. Environmental information .................................................. 47
11. Index .............................................................................................. 49

TABLE OF CONTENTS
4 - English
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify
the design and appearance and function of products without prior notice. This Operator's Manual deals
with version 2.5x of the mower’s control program.

English - 5
1. INTRODUCTION AND SAFETY
1. Introduction and
safety
1.1 Introduction
Congratulations on your choice of an exceptionally
high quality product. To get the best results from your
Husqvarna Automower™ requires knowledge of its
function. This Operator's manual contains important
information about the mower, how you install it and
how you use it.
The following system is used in the Operator's manual
to make this easier:
• Text written in italics is a reference to another part
of the Operator's Manual.
• Words written in bold are one of the buttons on
the mower's keypad.
• Words written in UPPERCASE and italics refer to
the position of the main switch and the different
operating modes on the mower.
IMPORTANT INFORMATION
Read through the Operator’s Manual carefully
and understand the content before using
your Automower.
WARNING
Automower can be dangerous if
incorrectly used.
1001-003

6 - English
1. INTRODUCTION AND SAFETY
1.2 Symbols on Automower™
These symbols can be found on the lawn mover. Study
them carefully so you understand their significance.
• Read through the Operator’s Manual carefully
and understand the content before using your
Automower.
• The warnings and safety instructions in this
Operator’s Manual must be carefully followed if
the mower is to be used safely and efficiently.
• Automower can only start when the main switch
is moved to the ON position and the correct PIN
code has been entered. Inspection and/or
maintenance must be carried out with the main
switch set to OFF.
• Keep your hands and feet away from the rotating
blades. Never place your hands or feet close to
or under the body when Automower is in
operation.
• Do not ride on Automower.
• This product conforms to the applicable
EU Directives.
• This product must be left at an appropriate
recycling station.
1001-003
1001-002
3012-664
DANGER
DANGER
KEEP HANDS and FEET AWAY
3012-733
3012-663
3012-665
6001-024
3012-689

English - 7
1. INTRODUCTION AND SAFETY
1.3 Symbols in the Operator’s
Manual
These symbols can be found in the Operator’s Manual.
Study them carefully so you understand their
significance.
• Inspection and/or maintenance must be carried
out with the main switch set to OFF.
• Always wear protective gloves when working
with the mower’s underframe.
• Never use a high-pressure washer or even
running water to clean Automower.
• A warning box indicates a risk of personal injury
exist, especially when the stated instructions are
not followed.
• An information box indicates a risk of material
damage exist, especially when the stated
instructions are not followed. The box is also
used where there is a risk of user error.
3012-749
3012-272
3012-271
WARNING
Xxxxxx xxxxx xxxx xxxx xxxxx xxx.
IMPORTANT INFORMATION
Xxxxxx xxxxx xxxx xxxx xxxxx xxx.

8 - English
1. INTRODUCTION AND SAFETY
1.4 Safety instructions
Use
• Please read the Operator's Manual carefully and
make sure you understand the instructions
before using Automower.
• It is not permitted to modify the original design of
Automower. All modifications are made at your
own risk.
• Check that there are no stones, branches, tools,
toys or other objects on the lawn that can
damage the blades and cause the mower to
stop.
• Start Automower according to the instructions.
When the main switch is in the ON position;
make sure you keep your hands and feet away
from the rotating blades. Never put your hands
and feet under the mower.
• Never lift up Automower or carry it around when
it is running.
• Do not let persons who do not know how
Automower works and behaves use the mower.
• Never use Automower if persons, especially
children, or pets, are in the immediate vicinity.
• Do not place objects on top of Automower.
• Do not allow Automower to be used with a
defective blade disc or body. Neither should it be
used with defective blades, screws, nuts or cables.
• Do not use Automower if the main switch does not
work.
• Always switch off Automower using the main
switch when you do not intend to use the mower.
Automower can only start when the main switch is
moved to the ON position and the correct PIN
code has been entered.
1001-003
3012-750
3012-663

English - 9
1. INTRODUCTION AND SAFETY
Transport
The original packaging should be used when
transporting Automower over long distances.
To safely move from or within the working area:
1. Press the STOP button to stop the mower.
2. Move the main switch to the OFF position if you
intend to carry the mower.
3. Carry the mower by the handle at the rear of the
mower. Carry the mower with the blade disc
away from the body.
Maintenance
• Inspect Automower each week and replace any
damaged or worn parts.
Check especially that the blades and blade disc
are not damaged. Replace all blades and screws
at the same time if necessary so that the rotating
parts are balanced, see 7. Maintenance on
page 37.
WARNING
When the mower is turned upside
down the main switch must always
be set to the OFF position.
The main switch should be set to the
OFF position during all work on the
mower’s underframe, such as
cleaning or replacing the blades.
3012-388
3012-748
3012-747

10 - English
2. PRESENTATION
2. Presentation
This chapter contains information you should be aware
of when planning the installation.
An installation of Husqvarna Automower™ comprises
three main components:
Automower, an automatic lawn mower that mows the
lawn by moving in an irregular pattern. The mower is
powered by a maintenance-free battery.
Loop generator/charger.
The loop generator/charger has two functions:
• To send control signals along the boundary wire.
• To charge the battery in Automower.
The loop generator/charger is connected to a 120 V
wall socket via an integrated power cord and to the
mower via a 6 ft long low voltage cable.
Wire, laid in a loop around Automower’s working
area. The boundary wire is laid around the edges of
the lawn and around objects and plants that the
mower must not run into.
The wire supplied with the installation is 500 ft long. If
this is not sufficient more wire can be purchased, with
a connector, and spliced onto the existing wire.
3012-751
3012-752
3012-221

English - 11
2. PRESENTATION
2.1 Automower™, what’s what?
The numbers in the picture correspond to:
1. Cutting height adjustment cover
2. Catch button to open the cutting height adjustment
cover
3. Front wheel
4. Drive wheel
5. Body
6. Stop button
7. Indicator lamps
8. Keypad
9. Main switch
10. Handle
11. Charger contact
12. Chassis box with electronics, battery and motors
13. Skid plate
14. Blade disc
15. Loop wire for boundary wire
16. Connection to boundary wire
17. LED for operation check of the boundary wire
18. Loop generator/charger
19. Staples
20. Connector for the loop wire
21. Measurement gauge for help when installing the
boundary wire
22. Solderless coupler for the loop wire
23. Operator’s Manual
3012-753
8
9
10 12
13 14
15
16
19 20 22
1
2
34
6
7
5
17
18
21
6
11
23

12 - English
2. PRESENTATION
2.2 Function of Automower™
Capacity
Automower is recommended for lawns up to 0.15 acre.
The size of the working area the mower can handle
depends on how much it is used. The larger the lawn
the more occasions per week Automower can work.
How large an area is mown per hour depends primarily
on the condition of the blades and the type of grass,
growth rate and humidity. The shape of the garden is
also significant. If the garden mainly consists of open
lawns, Automower can mow more per hour than if the
garden consists of several small lawns separated by
trees, flower beds and passages.
Automower must work several times a week for the
lawn to be mown properly. If the grass is too tall when
the mower starts to work the result will be poor. Neither
is it advisable to allow Automower to mow too often. If
the mower works too much, the lawn will appear
trampled down. How many times, and how long, the
mower should work per week, is determined among
others by the shape of the lawn, the length of the grass
and the condition of the blades. If the lawn is 0.15 acre
it is recommended to let Automower mow three times a
week. Match the use of Automower to your garden.
How long Automower mows and recharges can vary
depending on, among others, the ambient
temperature. Up to about 77 °F a fully charged
Automower mows for approximately 4 -6 hours,
depending on the age of the battery and the thickness
of the grass. It takes around 12 - 15 hours to fully
charge the battery in the mower. The mowing time
drops successively above 77 °F.
Mowing technique
The mowing system used by Automower is based on
an effective and energy efficient principle. Unlike
normal lawn mowers, Automower cuts the grass
instead of striking it off.
We recommend you allow Automower to mainly mow
in dry weather to obtain the best possible result.
Automower can even mow in the rain, however, wet
grass easily collects on the mower and the risk of
slipping on steep slopes is greater.
If there is a risk of thunder, the 120 V plug should be
removed.

English - 13
2. PRESENTATION
The blades must be in good condition to obtain the
best mowing result. In order to keep the blades sharp
for as long as possible it is important to keep the lawn
free from branches, small stones and other objects.
3012-422

14 - English
2. PRESENTATION
Working method
Automower automatically mows the lawn. Automower
automatically mows the lawn. When the battery is
discharged the mower stops on the lawn, and you need
to carry it to the loop generator/charger for charging.
When Automower body hits an obstacle, the mower
reverses and selects a new direction.
Two sensors, at the front and back on Automower,
sense when the mower approaches the boundary
wire. Automower overruns the wire by up to
27 centimeters (11") before it turns.
The STOP button on the top of Automower is mainly
used to stop the mower when it’s running. When the
STOP button is pressed a cover opens, behind which
there is a control panel. The STOP button remains
depressed until the cover is closed again. This acts
as start inhibitor.
You start the mower via the control panel on top of
Automower. Open the control panel cover by pressing
down the STOP button.
A four digit PIN code must be chosen and entered
when the main switch is set in the ON position for the
first time. (see page 31).
The chosen PIN code must then be entered each
time the mower is started. If the mower does not start
within 20 seconds the PIN code must be re-entered
until the mower starts. Slide shut the cover to start the
mower after the PIN code has been entered.
Automower can, to save energy, enter sleep mode.
The indicator lamps on the control panel are then
turned off completely.
The sleep mode is activated 25 minutes after the
STOP button has been pressed and then not reset to
the operating mode. Automower is then activated by
switching the main switch off and on.
The sleep mode can also be activated in the event of a
fault occurring during mowing or charging and which is
not rectified within 25 minutes. Automower is then
3012-772
3012-388
3012-779

English - 15
2. PRESENTATION
activated by pressing the STOP button.
Movement pattern
The mower’s movement pattern is irregular and is
determined by Automower itself. A movement pattern
is never repeated. This mowing system means the
lawn is mown equally without any mowing lines.
2.3 One Automower™in several
gardens
One Automower can easily be used for more than one
garden, where each garden has its own loop
generator/charger and boundary wire.
Contact your dealer for further information.
3012-755

16 - English
3. INSTALLATION
3. Installation
This chapter describes how you install Husqvarna
Automower™. Before starting the installation read the
previous chapter 2. Presentation.
Read the whole of this chapter too before starting the
installation. How the installation is made also affects
how well Automower will work. It is therefore important
to plan the installation carefully.
Planning is simplified if you make a sketch of the
working area, including all obstacles. This makes it
easier to see how the boundary wire should ideally be
placed. Draw how the boundary wire is to be routed on
the sketch.
Carry out the installation in the following steps:
3.1 Preparations.
3.2 Installation of the loop generator/charger.
3.3 Charging the battery.
3.4 Installation of the boundary wire.
3.5 Connecting the boundary wire.
3.6 Checking the installation.
3.7 Linking the Automower™ to the loop
generator/charger..
In order to carry out a complete start-up of Automower
the loop generator/charger and boundary wire must be
connected and the mower linked to the loop
generator/charger. If you would like to start the mower
without having completed the full boundary installation,
you can connect a temporary short loop around the
mower.

English - 17
3. INSTALLATION
3.1 Preparations
1. If the lawn in the proposed working area is taller
than 4", mow it using a normal lawn mower. Then
collect the clippings.
2. Read carefully through all the steps before the
installation.
3. Check that all parts for the installation are
included:
The numbers in brackets refer to the detail
diagram 2.1 Automower™, what’s what? on
page 11.
• Operator’s Manual (23)
• Automower
• Loop generator/charger (18)
• Loop wire for the boundary wire (15)
• Staples (19)
• Connector for the loop wire (20)
• Measurement gauge (21)
• Solderless coupler for the loop wire (22)
During installation you will also need: A hammer to
knock the staples into the ground, combination pliers,
and a straight spade if the boundary wire is to be
buried.
3.2 Installation of the loop
generator/charger
The loop generator/charger must be placed where it
is well ventilated and is not exposed to direct sunlight.
The mower's battery is spared if it is charged in the
lowest possible ambient temperature. It is also
beneficial if the transformer can be placed under a
roof.
IMPORTANT INFORMATION
The power cord for the loop
generator/charger must not be replaced. If
the power cord is damaged the loop
generator/charger must be scrapped and
replaced with a new unit.
3012-756
3012-757

18 - English
3. INSTALLATION
Consider the distance to a wall socket when choosing
the position. The loop generator/charger must be
connected to a 120 V wall socket and there must be
room for the mower when it is to charged.
It is recommended to use an earth fault-breaker when
connecting the transformer to the wall socket.
Tip! If, for reasons of space or for some other reason,
it is not suitable to charge the mower where the loop
generator/charger is positioned, a freestanding
charger can also be used. A charger can be
purchased as an accessory. Contact your dealer for
further information.
Installation and connecting the loop
generator/charger
1. Position the loop generator/charger in a suitable spot.
2. Connect the loop generator/charger's power cord
to a 120 V wall socket. It is preferable to use an
earth-fault breaker as recommended.
3.3 Charging the battery
Automower is supplied with an uncharged battery. As
soon as the loop generator/charger is connected, it is
possible to charge the mower.
1. Set the main switch to the ON position and leave
the cover for the control panel open.
2. Connect the charger cable from the loop
generator/charger to the charger contact on the
mower. The green indictator lamp Battery now
goes on. When the mower is fully charged the
green indicator lamp goes off, and the yellow
lamp starts flashing.
From an uncharged state the battery takes about
12 - 15 hours until it is fully charged.
Tip! Leave the mower connected to the charger cable
when not in use. As long as the mower is connected it
will be maintenance charged, which means the
battery will be fully charged when the mower is used.
This does not apply to winter storage, see 7.2 Winter
storage on page 38.
3012-752
3012-784
3012-758

English - 19
3. INSTALLATION
3.4 Installation of the boundary wire
The boundary wire can be installed in one of the
following ways:
• Securing the wire to the ground with staples.
It is preferable to staple down the boundary cable,
if you want to make adjustments to the boundary
wire during the first few weeks of operation.
• Bury the wire.
It is preferable to bury the boundary wire if you
want to dethatch or aerate the lawn.
If necessary both methods can be combined so one
part of the boundary wire is stapled down and the
remainder is buried.
Best position for the boundary wire
The boundary wire should be laid so it:
• Forms a loop around the working area for
Automower. Only an original boundary wire must
be used. This is tinned and has a high quality
insulation to withstand the dampness in the
ground.
• Is a maximum of 1200 ft long.
• Maintains a maximum distance of 80 ft from
Automower in the entire working area.
• The boundary wire is laid at different distances
from obstacles depending on what the working
area borders. The picture below shows how the
boundary wire should be routed around the
working area and around obstacles.
IMPORTANT INFORMATION
Automower cannot be used before the
installation is complete.

20 - English
3. INSTALLATION
Boundaries for the working area
If a high obstacle, for example a wall or fence,
borders the working area, the boundary wire should
be laid 14" from the obstacle. This will prevent
Automower from colliding with the obstacle and
reduce body wear.
If the working area borders against a small ditch, for
example, a flower bed or a small elevation, e.g. a low
verge (1" - 2"), the boundary wire should be laid 12"
inside the working area. This prevents the wheels
from driving into the ditch or up onto the verge.
3012-759US
3012-760US
3012-761US

English - 21
3. INSTALLATION
If the working area borders against a flat path or the
like that lies level with the lawn, it is possible to allow
Automower to run a little over the path. The boundary
wire should then be laid 4" from the edge of the path.
When the working area is divided by a flat slab path
that is level with the lawn, it is possible to allow
Automower to run over the path. It can be an
advantage to lay the boundary wire under the slabs.
The boundary wire can also be laid in the joint
between the slabs.
Note! Automower must never run over a gravel path
or similar material, which can damage the blades.
If the working area borders against, for example,
pools of water the boundary wire should be
supplemented with a fence or the like. The height must
then be at least 6". This will prevent Automower, under
any circumstances, coming outside of the working
area.
Boundaries within the working area
Use the boundary wire to demarcate areas inside the
working area by creating islands around obstacles
that can not withstand a collision, for example, flower
beds and fountains. Run the cable out to the area,
route it around the area to be demarcated and then
back along the same route. If staples are used, the
wire should be laid under the same staple on the
return route. When the boundary wire to and from the
island are close together, the mower can drive over
the wire.
Obstacles that can withstand a collision, for example,
trees or bushes higher than 6", do not need to be
demarcated by the boundary wire. Automower will turn
when it collides with this type of obstacle.
However, for the most gentle and silent operation, it is
preferable to demarcate all fixed objects in and around
the working area.
3012-762US
3012-763
3012-764US