Husqvarna CR 65 2012 Instruction manual

CR 65 2012
Workshop Manual Ed. 09-2011

HUSQVARNA MOTORCYCLES S.R.L. - Varese disclaims all liabilities
for any errors or omissions in this manual and reserves the right to make
changes to reect ongoing product development. Illustrations in the ma-
nual may differ from actual components. No reproduction in full or in part
without written authorisation.
1st Edition (09-2011)

a.1
simbolo
CR 65 2012
H02017
1
CR 65 : ZKHCR6530CV000001
Workshop Manual Ed. 09-2011
FOREWORD, TABLE OF CONTENTS
1st Edition (09-2011)
Printed in Italy
MODELS COVERED (from serial number onwards)
Copyright by
HUSQVARNA MOTORCYCLES S.R.L.
BMW Group
Technical Service
Via Nino Bixio, 8
21024
(Varese) - Italy
tel. ++39 0332 75.61.11
tel. ++39 0332 756 558
www.husqvarna-motorcycles.com
Workshop Manual
1. Chassis serial number
CR 65 / 2012

a.2
simbolo
CR 65 2012
FOREWORD, TABLE OF CONTENTS
Workshop Manual Ed. 09-2011
Foreword
This publication is designed for use by HUSQVARNA Service Centres to assist authorised personnel in the maintenance
and repair of the models covered in this manual. The technical information provided in this manual is a critical comple-
ment to operator training and operators should become thoroughly familiar with it.
For ease of understanding, diagrams and photographs are provided next to the text.
Notes with special signicance are identied as follows throughout the manual:
Accident-prevention rules for operator and persons working nearby.
Damage to vehicle and/or its components may result from non-compliance with relevant instructions.
Additional information concerning the operation covered in the text.
Useful tips
To prevent problems and ensure effective service work, observe the following HUSQVARNA recommendations:
– before repair, evaluate the customer's description of the problem and ask the appropriate questions to clearly identify
problem symptoms;
– diagnose the problem and identify the causes clearly. This manual provides basic background information that must
be supplemented with the operator's expertise and specic training available through HUSQVARNA held at regular
periods;
– plan ahead before starting work: gather any spare parts and tools to avoid unnecessary delays;
– avoid unnecessary disassembly work to get to the part that needs repairing.
Always read the relevant instructions and follow the disassembly sequence outlined in this manual.
Recommended shop practices
1 Always replace gaskets, sealing rings and split pins with new ones.
2 When loosening or tightening nuts or bolts, always begin with the bigger ones or from the centre. Tighten to the speci-
ed torque and follow a cross pattern.
3 Always mark any parts or positions that might be confused upon assembly.
4 Use genuine HUSQVARNA parts and the recommended lubricant brands.
5 Use special tools where specied.
6 Technical Bulletins might contain more up-to-date setting data and procedures than this manual. Be sure to read
them.
IMPORTANT: Where not specied, reassembled components must be tightened to the proper torque as indicated
in the tables provided in section "X".

a.3
simbolo
CR 65 2012
Workshop Manual Ed. 09-2011
FOREWORD, TABLE OF CONTENTS
Table of Contents
Title Section
Foreword, Table of Contents ............................................................................... a
Important Notices ................................................................................................ b
General Information.............................................................................................A
Maintenance........................................................................................................B
Troubleshooting.................................................................................................. C
Settings and Adjustments................................................................................... D
General Procedures ............................................................................................E
Engine Disassembly............................................................................................F
Engine Overhaul................................................................................................. G
Engine Reassembly............................................................................................ H
Front Suspension ................................................................................................. I
Rear Suspension................................................................................................. J
Brakes ................................................................................................................. L
Electrical System ................................................................................................ M
Engine Cooling ................................................................................................... N
Hydraulically Controlled Clutch............................................................................P
Fuel supply ..........................................................................................................S
Special Tools ......................................................................................................W
Tightening Torque Figures ...................................................................................X
Chassis and Wheels............................................................................................Y
NOTES
Unless otherwise specied, data and specications apply to all models.

b.1
CR 65 2012
b
Workshop Manual Ed. 09-2011
IMPORTANT NOTICES
Section

b.2
CR 65 2012
IMPORTANT NOTICES
Workshop Manual Ed. 09-2011
1) CR models are RACING motorcycles and are guaranteed to be free from
operating defects; a scheduled maintenance chart for racing use is provided in
Section B.
* In order to maintain the vehicle’s “Guarantee of Functionality”, the client must
follow the maintenance programme indicated in Section B by having the required
maintenance inspections carried out at authorised HUSQVARNA dealers. The
Customer bears all part replacement and labour costs needed to respect the
maintenance schedule. In case of motorcycle hire the warranty becomes NULL
and VOID.
Notes
Left and right side is determined when seated on motorcycle.
Z: number of teeth
A: Austria
AUS: Australia
B: Belgium
BR: Brazil
CDN: Canada
CH: Switzerland
D: Germany
E: Spain
F: France
FIN: Finland
GB: Great Britain
I: Italy
J: Japan
USA: United States of America
Unless otherwise specied, data and instructions apply to all market variants.

A.1
CR 65 2012
A
Workshop Manual Ed. 09-2011
GENERAL INFORMATION
Section

A.2
CR 65 2012
GENERAL INFORMATION
Workshop Manual Ed. 09-2011
Engine ..........................................................................................................A.3
Fuel system ..................................................................................................A.3
Lubrication....................................................................................................A.3
Cooling .........................................................................................................A.3
Ignition system..............................................................................................A.3
Kick ..............................................................................................................A.3
Primary drive ................................................................................................A.3
Gearbox........................................................................................................A.3
Secondary drive............................................................................................A.3
Drive chain....................................................................................................A.3
Chassis.........................................................................................................A.3
Suspension...................................................................................................A.3
Brakes ..........................................................................................................A.4
Wheels..........................................................................................................A.4
Tyres.............................................................................................................A.4
Overall dimensions - Weight.........................................................................A.4
Electrical components location.....................................................................A.5
Capacities.....................................................................................................A.5