Husqvarna Viking Epic 3 User manual

SPECIAL TECHNIQUES HOOP
240X150mm
User Instructions
The Special Techniques hoop is a reversible
hoop where you can embroider on both sides of
the hoop. This makes it possible to use several
embroidery techniques in just one hooping.
Combine basic embroidery with techniques like
appliqué, felting and bobbin work.
FR Un mode d’emploi en français peut se télécharger sur
www.husqvarnaviking.com. Rechercher “Special Techniques Hoop
240x150mm” sous le titre “Accessoires”.
DE Die Bedienungsanleitung auf Deutsch können Sie unter
www.husqvarnaviking.com herunterladen. Suche nach “Special Tech-
niques Hoop 240x150mm” unter der Überschrift “Zubehör”.
NL Nederlands gebruiksinstructies kunnen worden gedownload op
www.husqvarnaviking.com. Zoeken naar “Special Techniques Hoop
240x150mm” onder de kop “Accessoires“.
IT Le istruzioni d’uso in italiano sono disponibili per lo scarico da www.
husqvarnaviking.com. Cerca in “Special Techniques Hoop 240x150mm”
sotto il titolo “Accessori”.
ES Las instrucciones de uso en español están disponibles para su
descarga en www.husqvarnaviking.com. Buscar “Special Techniques Hoop
240x150mm” en el apartado “Accesorios”.
SV Användarinstruktioner på svenska nns att hämta på
www.husqvarnaviking.com. Sök efter “Special Techniques Hoop
240x150mm” under rubriken “Tillbehör”.
DK En dansk brugervejledning kan downloades fra
www.husqvarnaviking.com. Søge etter “Special Techniques Hoop
240x150mm” under overskriften “Exstratillbehør”.
NO Norsk bruksanvisning er tilgjengelig for nedlasting fra
www.husqvarnaviking.com. Søke etter “Special Techniques Hoop
240x150mm” under overskriften “Exstratillbehør”.
FI Suomenkieliset käyttöohjeet ovat ladattavissa osoitteessa
www.husqvarnaviking.com. Etsiä “Special Techniques Hoop 240x150mm”
otsikolla “Lisätarvikkeet”.
RU Инструкции по эксплуатации на русском языке можно загрузить
на веб-сайте www.husqvarnaviking.com. искать “Special Techniques
Hoop 240x150mm” под заголовком “Принадлежности”.
471132926A VIKING is a trademark of KSIN Luxembourg II, S.a.r.l. HUSQVARNA and the “H” Crown Device are trademarks of Husqvarna AB and are used under license. © 2023 KSIN Luxembourg II, S.a.r.l.
All rights reserved
240x150
Outer Hoop A Inner Hoop BSpecial Techniques Hoop
Quick Release Retaining Screw
Depending on what technique you embroider, the embroidery process is different. For each design, you will be guided by your machine, and
notified when it is time to change machine equipment or settings.
For felting and bobbin work techniques you need to have optional accessories, how to use those accessories are described in respective
accessory user instruction.
Embroidery Hoop Connector A
Embroidery Hoop Connector B

HOOPING
When hooping, always hoop with the A-side facing up.
The fabric should be placed in the hoop with the right
side up.
• Open the quick release on the outer hoop A, and
loosen the retaining screw. Remove the inner hoop B.
• Place the outer hoop A on a firm flat surface with the
screw to the lower right.
• Place the stabilizer and fabric, with the right sides
facing up, on top of the outer hoop A. Place the inner
hoop B on top of the fabric with the small arrows at
the bottom edge. If you can see the hoop size in the
lower part of the inner hoop, you have attached it
correctly.
Note: different techniques require different stabilizers.
The placement of the stabilizer could also differ. See
directions for each technique.
• Push the inner hoop B firmly into the outer hoop A.
Unlike other hoops, the inner and outer hoops are
not levelled once correctly hooped.
• Hold the fabric and stabilizer with your right hand
while using your left hand to push the fabric towards
the left edge of the hoop. Carefully pull the fabric
outside the hoop until it is flat and taut in the hoop.
Carefully pull the fabric at the top and bottom of the
hoop.
• Close the quick release.
• Turn the hoop over. Pull the fabric edge to the left.
• Adjust the pressure of the outer hoop by turning the
retaining screw until its really tight. The fabric should
be taut in the hoop for the best results.
For tips and hints on how to hoop for the different
techniques, please refer to the instructions for respective
accessory. You can also learn more from the turorials built
into your machine.
MACHINE SET UP
For each embroidery design, your machine will let you
know how to prepare for the different color/technique
blocks. You will be notified when the hoop should be
flipped, when to prepare for felting, bobbin work etc.
TIPS & HINTS
• Always hoop with the A-side facing up. The fabric
should be placed in the hoop with the right side up.
• When embroidering with the A-side connected,
activate "Sensor Q Foot" in Embroidery Settings and
use the Sensor Q Foot.
• Felting and bobbin work is done with the B-side
connected.
• When embroidering with the B-side attached, activate
"Floating Foot" in Embroidery Settings. Use the Felting
accessory or the R Foot.
• When using the felting accessory or the R-Foot you
might need to adjust the presser foot pivot height for
best result.
240x150 240x150
240x150
Use floating foot (or felting foot) when B-side is attached
Use Sensor Q Foot when A-side is attached