Husqvarna HUSKYLOCK 1002 User manual

HANDBOOK
FOR
HUSKYLOCK
SEWING
MACHINE
MODELS
ic
Husqvarna

“IMPORTANT SAFETY INSTRUCTIONS”
When using
the sewing machine,
basic safety precautions should always
be
followed,
including the
following.
“Read all
instructions before using.”
DANGER
— To reduce the risk of
electric shock.
1.
The sewing machine should never be left unattended
when plugged in. Always
unplug this sewing ma
chine from the electrical outlet immediately after using and
before
cleaning.
2.
Always
unplug before relamping. Replace bulb with same type rated 2.4 watts.
\AIAR
N IN
G
— To reduce the risk of burns, fire,
electric
shock, or injury to persons.
1
Do
not
allow
to be used as
a
toy. Close attention is necessary when the sewing machine is used by or near children.
2
Use this
sewing
machine only for its intended use as described
in this
manual. Use only accessories recommended
by
the manufacturer
as
contained in this manual.
3
Never operate this sewing machine if it has
a
damaged cord or plug, if it is not working properly, if
it has been
dropped or damaged, or dropped into water. Return the sewing machine to the nearest
authorized
dealer
or service
center for examination, repair, electrical
or
mechanical adjustment.
4 Never operate the sewing machine
with any air openings
blocked. Keep
ventilation openings of the sewing machine
and
toot control free from
the accumulation of lint,
dust,
and loose
cloth.
5
Never drop or insert any
object into any opening.
6.
Do
not
use
outdoors.
I. Do
not operate where
aerosol (spray) products are being used or where oxygen is being administered.
B To
disconnect, turn the main
switch to the
symbol
“0”
position which represents off,
then remove plug from outlet.
9,
Do
not unplug
by
pulling on
cord. To unplug, grasp the
plug, not the cord.
10.
Keep fingers away from all
moving
parts. Special care is required around the sewing machine
needle.
11. Always use
the proper
needle plate, The wrong plate
can
cause
the needle to break.
12. Do
not
use
bent needles.
13. Do
not pull or push fabric while
stitching. It may deflect the
needle causing it to break.
14. Swrtch
the sewing machine
to the symbol
“0”
position when
making any
adjustments in the needle area, such
as
threading
needle, changing needle,
threading bobbin, or
changing
presser foot, and the like.
15. Always
unplug
the sewing machine from the electrical outlet when removing covers, lubricating,
or
when making
any of the user servicing adjustments
mentioned
in the instruction manual.
“SAVE THESE
INSTRUCTIONS”
‘ 4 This sewing
machine is intended for
household
use.”

•
When
leaving
the
sewing machine
unattended,
the
mains
switch
of
the
machine
must
be
switched
off
or
the
plug
must
be
removed
from
the socket-outlet.
• When servicing
the
sewing
machine,
or when
re
moving covers
or
changing
lamps,
the
machine
or
the
electrical set
must
be
disconnected
from
the
supply
by
removing
the
plug
from
the
socket-
outlet.
FOR
USERS
IN
THE
UK.
EIRE,
MALTA
AND
CYPRUS
ONLY.
If
your sewing
machine
is
fitted
with
a 3
pin
non
rewireable BS
plug
then
please
read the
following.
IMPORTANT
If the
available
socket outlet
is
not
suitable
for
the
plug
supplied
with
this
equipment,
it
should
be
cut
off
and
an
appropriate
three
pin
plug
fitted.
With
al
ternative
plugs
an
approved
fuse
must
be
fitted
in
the
plug.
NOTE:
The plug
severed
from
the
mains
lead
must
be
destroyed as
a
plug
with
bared
flexible
cords
is
hazardous if
engaged
in
a
live
socket
outlet.
In
the
event
of
replacing
the
plug
fuse,
use
a
fuse
ap
proved
by
ASTA
to
BS
1362,
i.e.
carrying
the
mark,
rating
as marked
on
plug.
Always
replace
the fuse
cover,
never
use
plugs
with
the fuse
cover omitted.
WARNING:
DO
NOT
CONNNECT
EITHER
WIRE
TO
THE
EARTH
TERMINAL
WHICH
IS
MARKED
WITH THE LETTER
‘E’,
BY
THE EARTH
SYMBOL
. OR
COLOURED
GREEN
OR
YELLOW.
The
wires
in this
mains
lead
are
coloured in
accord
ance
with
the
following
code:
Blue
Brown
Neutral
Live
As the
colours
of
the
wiring
in the mains
lead
of this
appliance may
not
correspond
with
the
coloured
markings
identifying
the terminals
in
your
plug,
pro
ceed
as
follows.
The
wire
which
is
coloured
blue
must
be connected
to
the terminal
which
is
marked
with
the letter
‘N’
or
coloured
black
or blue.
The
wire which
is
coloured
brown
must
be con
nected
to
the
terminal which
is
marked
with
the
let
ter ‘L’
or
coloured red
or
brown.

CONGRATULATIONS
ON CHOOSING
THIS
COMPACT
OVERLOCK
SEWING
MACHINE
Your
machine
is
a
high
quality,
easy-to-use product.
To
fully
enjoy
all
the features, we
suggest
that
you
study
this
booklet.
If you
need
more
information
regarding
the
use of
your
machine,
your
nearest authorized dealer
is always
happy to
be
of service.
Enjoy
yourself!
WHEN THREADING,
REPLACING
NEE[)LE
OR
LIGHT
BULB,
BE
SURE TO
TURN OFF
THE
MAIN
POWER
SWITCH
OF
THE MA
CHINE.
WHEN
THE
MACHINE
IS
NOT IN
USE, IT
IS
RECOMMENDEI)
THAT
THE ELECTRIC
SUPPLY
PLUG IS
DISCONNECTED
FROM
THE WALL
SOCKET
TO
AVoID
ANY POSSIBLE
HAZARDS.

TABLE OF CONTENTS
NAMES OF PARTS AND THEIR FUNCTIONS 1—4
Five-thread
model
Four-thread models
ACCESSORIES 5—6
HOW TO
USE THE
ADVISOR FUNCTION
7—8
Basic operation
Explanation of
troubleshooting screen
SETTING UP
YOUR MACHINE 9
Motor
NEEDLE 10—12
For five-thread model
For four-thread models
THREADING
13—17
Before threading...
Threading
upper looper
Threading lower looper
Threading the double chain stitch
looper
thread
THREADING
NEEDLES
18—19
1)
Right needle thread
2) Threading the left
needle thread
3)
Double chain stitch needle thread
4)
Threading the right needle for
model
with no LCD
STITCH
SELECTION 21—22
THREAD
SETTING
FOR VARIOUS
STITCHES
23—24
Five-thread overlock stitch
Four-thread overlock stitch
Three-thread overlock
stitch
Double chain stitch
SETTING FOR DOUBLE CHAIN
STITCH SEWING
25—27
1.
Retracting
the upper looper
2.
Retracting the upper cutter
3. Removal and
installation of cutter
cover II
SETTING FOR TWO-THREAD OVERLOCK STITCH SEWING 28
SEWING
29—iO
Four-thread,
three-thread
or
two-thread sewing
Five-thread or double chain stitch sewing
THREAD TENSION ADJUSTMENT 31—34
RELATIONSHIP BETWEEN SEWING MATERIAL, THREAD AND NEEDLE
,., 35
STITCH LENGTH
AND
STITCH
WIDTH
36
Stitch length
Stitch width
STITCH WIDTH AND
CUTTING
WIDTH FINE-TUNE ADJUSTMENT
37
DIFFERENTIAL FEED
38
PRESSER FOOT
39
NARROW
OVERLOCK STITCH/ROLLED
EDGE
STITCH 40—41
EXAMPLES OF SEWING APPLICATIONS FOR
OVERLOCK
SEWING
MACHINES
42—43
PERFORMANCE PROBLEMS
44
CHANGING THE LIGHT BULB 45
MAINTENANCE
46

NAMES
OF PARTS AND THEIR
FUNCTIONS
at w .sr w at
W —
Five-thread model
/1
(
[)contrist
/ idj ustfli ent Cl i
Speed
selec tor
(I St)
IL
1/2
(Sto\
Rdted
illTIt)
E,ulb
8V
24VV
LAMP MAX 24W
(fIJ
Ott-
ON
cj
Close the Ironi
O\
or hetore
operating
the
nla
hnie.
Close the material plate
cover hefore
operating
the machine.
—1

)
Pressure
adjustment
dial
®Thread tension
dial
tor
eu
needle
thread
and
tor
double ( ham
stitch
thread
®
Thread tension
dial
tor
right
needle
thread
(&
Liquid
r
stal
display
ILC[))
®
Liquid
crystal
display
keys
©
Thread tension
dial
for
upper looper
thread
®Thread
tension
dial
tor lower
looper
thread
®
Presser
foot
leer
®Thread tension
dial
(For
double
diain
stitch
looper
thread)
iE
Front
cover
@
Needle
plate
©
Presser
foot
Efj
Stitch
width
control
dial
Stitch
length
control
dial
Ditterential
teed
control
dial
Cutter
retracting knob
©
Material
plate
coser
(rear)
Light
switch
Material
plate
cover
)tront)
Double
chain
stitch
looper
threading
mechanism
@
Control
cover
Stitch
finger
change
lever
Lower
looper
threading
mechanism
Upper
looper
Movable
stitch
finger
2i3
Thread
convert
lever
©
Double
chain
stitch
looper
®
Lower
looper
©
Chain stitch
leser
(Upper
looper
release
knob)
©
LCD
contrast
adjustment
dial
®
Thread
guide
Thread
holder
Thread
holder
stand
Handle
©
Spool
pin
i
Spool
support
©
Main
power
switch
Power
cord
socket
Foot
control
jack
Handwheel
O
Foot
control
©
Power
cord
©
Spool
support
br
double
chain
stitch
thread
C
7
-2-

NAMES
OF PARTS AND
THEIR FUNCTIONS
— W
e
.r
Four-thread models
L( I)
adjustnwnt
dial
Speed
selector
/
Hi
tblow
Model th 0
[) on
Rdted lam
p
bulb
by 2 4V5
LAMP MAX 24W
rU
OFF
ON
.2
Close the front over
belore
operating the machine
II L
Close
the material plate cover before
operating the machine.
-3

CD
Pressure
adjustment
dial
CD
Thread tension
dial for
left needle thread
CD
Thread tension
dial
tor right
needle thread
rodel
ith ads
sor function]
CD
Liquid rystal
display
(LCD)
CD
Liquid
cr5
stal
display keys
®
L(
L)
contrast
adjustment dial
CD
Thread
tension
dial or upper
looper
thread
CD
Thread
tension dial tor
lower looper
thread
®
Presser
toot
lever
®
Front i
over
®
Needle plate
@
Presser toot
0
Stitch
width
control dial
0
Stitch
length control
dial
0
Differential
feed control
dial
0
Cutter retracting
knob
©
Material plate
cover
(rear)
0
Light switch
co Material
plate cover
fronp
Control
cover
D
Stitch finger
change lever
©
Upper looper
Movable stitch
finger
®
23 Thread
convert
leser
Lower
looper
[owed looper
threading mec
hanisni
®
Thread
guide
Thread
holder
-4-
Thread
holder stand
0
Handle
0
Spool
pin
0
Spool
support
0
Power
cord soc ket
0
Foot
control jack
0
Main power
switch
0
Handwheel
0
Power cord
0
Foot control
For rili)(l
el
with [Cl)
0
Foot control
(For
nirolel
without
[CD)

> > I rn
C)
m
ci, C,) 0
m Cl,
> (Th fl m 0
0
><