HYEKU X3 User manual

X3 WIRELESS MECHANICAL KEYBOARD
Quick Start Guide

1. Product introduction
The user interface and other illustrations of the product accessories in the manual are all schematic diagrams, which are only for reference. Due to the
update and upgrading of the product, the actual product may be slightly different from the schematic diagram. Please refer to the actual product.
Self-locking hand rest
"One-key double Function"key(Fn combination key)
Fn Key
Tripod
Type - c interface
Receiver
Power switch
USB cable

2. Schematic diagram of assembly and disassembly for keyboard hand rest
Assembly instructions of keyboard hand rest Disassembly instructions of keyboard hand rest
1. Grasp the middle end of the hand rest and align it with the keyboard
lock slot, push it in slightly, and hear a "click". Indicates that the
keyboard has been locked.
2. The effect of Complete assembly.
1. Grasp the middle of the hand rest and push it forward slightly, and then
quickly pull it out after hearing a "click". Remove the hand rest.
2. The effect of complete disassembly.

2.4G mode Wired mode
3. Plug the receiver into the USB port of the computer
※After connecting to the computer, the
system automatically detects the 2.4G
device and installs it by itself. It can be
used after the installation is successful.
3. Installation instructions
1. Turn on the power switch on the back of the keyboard
2. Take out the 2.4G wireless receiver
1. Connect the "TYPE-C" of the data cable to the keyboard.
※After connecting to the computer, the system will automatically detect
the USB device and install it by itself.After successful installation, the user
will be prompted to use the current device.
2. Insert the USB connector into the USB port of the computer.
> For good 2.4g wireless performance, plug the USB wireless receiver into the USB port on the PC front panel or connect through a USB extension cord to bring the USB
wireless receiver closer to the keyboard.

4. FN combination function keys
Keep pressing 3S to restore
factory default
backlight constant brightness
mode
Custom light mode
Backlight interactive mode
cycle switch
Backlit breathing mode
Play / Pause Next songPrev song
Volume + Mute
Full key / 6 key anti-ghosting
(cable model）
Win lock
Full light switch
Custom light clearing
(long press 3 seconds)
Volume -
Custom lighting mode: Short press FN + END to bring up the current custom light, and then long press FN + END 3S indicator lights CAPS and SCRLK
and the END button to flash, then enter the custom light effect mode. At this time, press the required key to modify the on-off and on-on status of the
corresponding LED, and press FN + END to save and exit.

Adjust the backlight
brightness - brighter
Adjust the speed of backlight
change - fast
Adjust the backlight
brightness - dimming
Adjust the speed of backlight
change - slow
Lock all keys
When the keyboard is locked, the
"F12" button light is flashes
5. Charging instructions
The USB cable will automatically charge when connected to the computer. The "Fn key" light flashes when charging, and the "Fn key" light
follows the current light mode when fully charged. In wireless mode, if the battery is low, the "Fn key" light will flash, please connect to the
USB cable for charging.

8. Warning
If any liquid enters the product , please immediately disconnect from the computer and remove the product. Continued use may cause fire or
electric shock, please contact the agent for inspection and maintenance.
Check the product shell regularly for any damage, maintenance operations are outside the scope of product compliance requirements.
Disassembly, replacement of parts , modification or modification without express approval will cause the user to lose the right of operating the
equipment and the warranty failure.
7. The name and content of the hazardous substance in the product
Hazardous substances
(Hg) (Cd) (Cr(VI)) (PBB) (PBDE)
Component
name
keyboard body
Metal case
Plastic keys
This form has been prepared in accordance with the requirements of SJ/T 11364.
O : Indicates that the content of the hazardous substance in all
homogeneous materials of the component is below the limit
specified in GB/T 26572.
X : Indicates that the hazardous substance is contained in at least
one homogeneous material of the component. The quantity
exceeds the limit specified in GB/T 26572.
(Pb)
6. Basic specifications
Battery capacity: 2300mah
Cable Material: USB Cable braided wire
Weight:
920g
Size: 357 x 133 x 37 mm
Keyboard type: Dual-mode mechanical keyboard
Switch: Kailh upgrade BOX Switch
( Hexgears custom-made )
Switch life: 100 Million Cycles
Report Rate: 1000HZ ( Wired mode )
Backlight: Monochromatic
Function: FN combination function key
Attended mode: 2.4G / Wired
Voltage / Current:
3.7V / 300mA
Keypad: 87 key/Anti-ghosting ( Wired mode )
Supporting: Windows all/Mac OS/Android