i-PRO WV-S1536LTA Installation guide

Basic Information
Network Camera
Model No. WV-S1536LT
“<Control No.: C****>” used in these documents should be used to search for information on our
technical information website (https://i-pro.com/global/en/surveillance/training-support/support/
technical-information) and will guide you to the right information.
• microSDXC/ microSDHC/ microSD memory card is described as microSD
memory card.
• The external appearance and other parts shown in this manual may differ
from the actual product within the scope that will not interfere with normal
use due to improvement of the product.
About the user manuals
Product documentation is composed of the following documents.
•Installation Guide (accessory): Provides information about “Precautions”, “Precautions for
installation” and the installation method.
•Basic Information (this document): Provides information about “Precautions for use”, “Parts and
functions” and “Detail specifications”.
•Operating Instructions (Refer to the link on the following support website): Explains how to
perform the settings and how to operate this camera.
https://i-pro.com/global/en/surveillance/training-support/documentation-database-list

2
Contents
Limitation of liability....................................................................................................................... 3
Disclaimer of warranty................................................................................................................... 3
System requirements for a PC ...................................................................................................... 4
Network security ........................................................................................................................... 5
Precautions for use ....................................................................................................................... 6
Parts and functions ....................................................................................................................... 8
Insert / remove a microSD memory card .................................................................................... 13
Troubleshooting........................................................................................................................... 15
Detail specifications .................................................................................................................... 17

3
Limitation of liability
THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
THE THIRD PARTY'S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Disclaimer of warranty
IN NO EVENT SHALL i-PRO Co., Ltd. BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT
FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES,
INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,
SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2) ANY INCONVENIENCE, LOSS, OR DAMAGE CAUSED BY INAPPROPRIATE USE OR
NEGLIGENT OPERATION OF THE USER;
(3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR
MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THE
MALFUNCTION OR TROUBLE;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO
ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING
OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION
AS A PHOTOGRAPHED SUBJECT DUE TO VIOLATION OF PRIVACY CONCERNING A
SURVEILLANCE CAMERA'S PICTURE OR SAVED DATA, FOR SOME REASON (INCLUDING
USE WHEN USER AUTHENTICATION ON THE AUTHENTICATION SETTING SCREEN IS SET
TO OFF), BECOMING PUBLIC OR BEING USED FOR ANY PURPOSE;
(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE (INCLUDING INITIALIZATION OF
THE PRODUCT DUE TO FORGOTTEN AUTHENTICATION INFORMATION SUCH AS A USER
NAME AND PASSWORD).

4
System requirements for a PC
CPU: Intel®CoreTM Processor family
- Intel®CoreTM i5-6500 or faster
- Intel®CoreTM i7-6700 or faster recommended
Memory:
4 GB (2 GB x 2, Dual Channel) or more recommended.
Network interface: 10BASE-T/100BASE-TX 1 port
Audio interface: Sound card (when using the audio function)
Monitor: Image capture size: 1024 x 768 pixels or more
Color: 24-bit True color or better
OS: Microsoft Windows 11
Microsoft Windows 10
Web browser: Microsoft Edge
Firefox
Google ChromeTM
Others: Adobe®Reader®or Acrobat Reader®
(It is necessary to view the PDF file.)
IMPORTANT:
• For information on the operation verification of web browsers, refer to our technical
information website <Control No.: C0132>.
• When using a PC that does not meet the above requirements, displaying of images may
become slower or the web browser may become inoperable.
• Audio may not be heard if a sound card is not installed on a PC. Audio may be interrupted
depending on the network environment.

5
As you will use this unit connected to a network, your attention is called to the following security
risks.
ALeakage or theft of information through this unit
BUse of this unit for illegal operations by persons with malicious intent
CInterference with or stoppage of this unit by persons with malicious intent
It is your responsibility to take precautions such as those described below to protect yourself
against the above network security risks.
• Use this unit in a network secured by a firewall, etc.
• If this unit is connected to a network that includes PCs, make sure that the system is not
infected by computer viruses or other malicious entities (using a regularly updated anti-virus
program, anti-spyware program, etc.).
• To prevent unauthorized access, use user-authentication, set user names and passwords, and
limit which users can log in.
• Apply measures such as user authentication to protect your network against leakage or theft of
information, including image data, authentication information (user names and passwords),
alarm mail information and DDNS server information.
• After the unit is accessed by the administrator, make sure to close the browser.
• Change the administrator password periodically. Additionally, save user authentication
information (user names and passwords) in such a way that it is kept out of the hands of third
parties.
• Do not install the camera in locations where the camera or the cables can be destroyed or
damaged by persons with malicious intent.
Network security

6
When the product is accessible from the
Internet
To prevent unauthorized access, note the
following.
• Leave user authentication turned on.
• Periodically change passwords that are used
to access the product.
Refer to the Operating Instructions for
information about how to change passwords.
To keep on using with stable performance
Do not use this product in hot and humid
conditions for a long time. Failure to observe this
causes component degradation resulting in life
shortening of this product. Do not expose this
product to direct heat sources such as a heater.
Usage such as switching the power ON/OFF
frequently could lead to failure of the camera.
Handle this product with care.
Do not drop this product, nor apply shock or
vibration to the product. Failure to observe this
may cause trouble.
Do not subject front portion to strong impact.
Doing so may cause damage or immersion.
Do not directly touch the lens surface and
front panel directly with your bare hands.
A dirty front panel or lens causes deterioration of
picture quality.
When an error is detected, this product will
restart automatically.
This product will be inoperable for around
2minutes after the restart just as when the power
is turned on.
About the automatic status detection
function
When this product malfunctions due to
exogenous noise, etc. for 30 seconds or more,
the product will automatically restart and will return
to normal state. When the product is restart,
initialization will be carried out as when the power
of the product is turned on. When the product
repeatedly resets, exogenous noise level around
the product may be high and that may cause
malfunction. Contact your dealer for instructions.
Periodically images on the screen appear to
be distorted
When the camera is installed in a location where it
is subject to small vibrations (for example, when it
is installed near devices that vibrate), images may
appear distorted and stretched lengthways. This
phenomenon is a characteristic of image pickup
devices that use CMOS sensors and is caused by
the relationship between the periodic movements
of the camera and the timing that the image
sensor reads images. This is not a problem with
the camera. To reduce the possibility of this
phenomenon occurring, install the camera in a
secure location.
About the ventilation opening
• Because humidity is retained internally in the
camera, the camera has a ventilation opening
and contains moisture absorption gel.
• Depending on conditions such as
temperature, humidity or the climate,
condensation may form and it may take time
to dehumidify.
• Do not block the surface of the ventilation
opening.
Ventilation opening
What to do if “WARMING UP-PLEASE WAIT”
appears on the display.
This message indicates that the temperature
inside the camera has become extremely low.
The camera will be automatically restarted when
the inside the camera is warmed up by the built-in
heater. Please wait for a while.
We shall not be liable for content
compensation, losses of recorded or
edited content and any direct or indirect
consequent damages caused by failure to
record or edit due to faults with this unit or
the microSD memory card. In addition, the
same provisions apply after unit is reparied.
Precautions for use

7
About the CMOS image sensor
• When continuously shooting a bright light
source such as a spotlight, the color filter of
the CMOS image sensor may become
deteriorated and this may cause
discoloration. Even when changing the fixed
shooting direction after continuously shooting
a spotlight for a certain period, the
discoloration may remain.
• When shooting fast-moving subjects or
objects crossing the shooting area may look
to be bending askew.
Cleaning this product body
Be sure to turn off the power before cleaning.
Failure to observe this may cause injury.
Do not use benzine, thinner, alcohol, or any other
types of solvents or detergents. Otherwise, it may
cause discoloration. When using a chemical cloth
for cleaning, read the caution provided with the
chemical cloth product.
• Do not loozen or remove screws unless
instructed to do so in the product
documentation.
Cleaning the lens
Use a lens cleaning paper (used to clean camera
lenses or lenses of spectacles). When using
solvent, use an alcohols solvent and do not use a
glass cleaner or a thinner.
Cleaning of the front panel
Use lens cleaning paper (used to clean camera or
spectacles lenses) to remove any dirt on the front
panel. If dust or the like is adhered at this time,
the front panel may get scratched. We
recommend rinsing for stubborn stains.
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE AVC
PATENT PORTFOLIO LICENSE FOR THE
PERSONAL USE OF A CONSUMER OR OTHER
USES IN WHICH IT DOES NOT RECEIVE
REMUNERATION TO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC STANDARD (“AVC
VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT
WAS ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE AVC VIDEO. NO
LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG
LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM
Product disposal/transfer
Data saved on this product or a storage device
used with this product may lead to personal
information leakage. When it is necessary to
dispose or give this product to someone, even
when for repair, make sure that there is no data on
this product.
When abandoning the memory media, it is
recommended to destroy it physically after
deleting data by PC.
Effects on images and image quality
Under the following conditions, image quality may
deteriorate or images may become difficult to see.
• When there are raindrops on the front panel
due to wind during rainfall.
• When there is snow on the front panel due to
wind during snowfall. (varies depending on
the amount and quality of snowfall).
• When the front panel is dirty due to dust in
the air or vehicle exhaust.
About HEVC (High Efficiency Video Coding)
patents
Covered by one or more claims of the HEVC
patents listed at patentlist.accessadvance.com.
Router
When connecting this product to the Internet, use
a broadband router with the port forwarding
function (NAT, IP masquerade).
Refer to the Operating Instructions for further
information about the port forwarding function.
Time & date setting
It is necessary to set the time & date before
putting this product into operation. Refer to the
Operating Instructions for descriptions of how to
perform the settings.

8
■ Cables
[1] RJ45 Network cable
I/O Cable
WV-QCA501A (option)
[1]
Ethernet cable
(category 5e or better, straight,
4 pairs (8 pins))
[3] Audio input cable (white)
[4] Audio output cable (black)
[5] 4P alarm cable
(WV-QCA501A accessory)
[2] 2P power cable
(WV-QCA501A accessory)
12 V DC (red)
GND (black)
[2]
Power supply cable
[5] EXT I/O cable
[6] MONITOR OUT terminal
(factory shipment: NTSC monitor)
[1] RJ45 Network cable
Connect an Ethernet cable (category 5e or better, straight, 4 pairs (8 pins)) to the network connector.
IMPORTANT:
• Use all 4 pairs (8 pins) of the Ethernet cable.
• The maximum cable length is 100 m {328 feet}.
• Make sure that the PoE device in use is compliant with IEEE802.3af standard.
• When connecting both the 12 V DC power supply and the PoE device for power supply, 12V
DC will be used for power supply.
• When the Ethernet cable is disconnected once, reconnect the cable after around 2seconds.
When the cable is quickly reconnected, the power may not be supplied from the PoE device.
Parts and functions

9
[2] Power supply cable / 2P power cable (WV-QCA501A accessory)
Connect the output cable of the DC power supply to the 2P power cable.
IMPORTANT:
• Be sure to use the 2P power cable provided with WV-QCA501A.
• Be sure to fully insert the 2P power cable into the power supply cable.
Otherwise, it may damage the camera or cause malfunction.
• When installing the camera, make sure that excessive force is not applied to the power cable.
• Be sure to use an AC adaptor compliant with the Specifications (written in the indication label
on the bottom side of this unit) regarding power source and power consumption.
[3] Audio input cable (white)
Connect a microphone or the line out of an external device using a stereo mini plug ( ø 3.5 mm).
<For microphone input>
• Re commended microphone (locally procured) : Plug-in power type
(Sensitivity of microphone: –51 dB to -38 dB (0 dB=1 V/Pa,1 kHz))
• Input impedance: Approx. 2 kΩ (unbalanced)
• Supply voltage: 2.5 V ±0.5 V
• Recommended cable length: Less than 1 m {3.28 feet}
<For line input>
• Input level for the line input: Approx. –10 dBV
• Recommended cable length: Less than 10 m {32.8 feet}
[4] Audio output cable (black)
Connect an external speaker* using a stereo mini plug (ø3.5 mm). (Audio output is monaural.)
• Output impedance: Approx. 600 Ω (unbalanced)
• Recommended cable length: Less than 10m {32.8feet}
• Output level: –20 dBV *Use a powered speaker.
IMPORTANT:
• Connect/disconnect the audio cables and turn on the power of the camera after turning off
the power of the audio output devices. Otherwise, loud noise may be heard from the speaker.
• Make sure that the stereo mini plug is connected to this cable. When a monaural mini plug is
connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conversion cable
(mono-stereo).

10
[5] EXT I/O cable / 4P alarm cable (WV-QCA501A accessory)
Note:
• Off, input, and output of the ALARM IN2 and 3 can be switched by configuring the setting.
Refer to the Operating Instructions for further information about the ALARM IN2 and 3 settings
(“Off”, “Alarm input”, “Alarm output” or “AUX output”).
<Ratings>
• Alarm input1 / Black & white input / Auto time adjustment input, Alarm input2, Alarm input3
Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive current: 1mA or more)
• Alarm output, AUX output
Output specication : Open collector output (maximum applied voltage: 20 V DC)
OPEN: 4 V - 5 V DC by internal pull-up
CLOSE: Output voltage 1 V DC or less (maximum drive current: 50 mA)
4P alarm cable
GND (Black)
ALARM IN3 (Alarm input3 / AUX output) (Gray)
ALARM IN2 (Alarm input2 / Alarm output) (Red)
ALARM IN1 (Alarm input1 / Black & white input / Auto time adjustment input)
(Green)
IMPORTANT:
• Install external devices so that they do not exceed the rating of the network camera.
• When using the ALARM IN2 and/or 3 as the output terminals, ensure they do not cause signal
collision with external signals.
[6] MONITOR OUT terminal (factory shipment: NTSC monitor)
Used to connect a monitor used for adjustments during installation or when performing service.
IMPORTANT:
• The adjustment monitor is used for checking the adjustment of the angular field of view when
installing the camera or when servicing. It is not provided for recording/monitoring use.
• Depending on the monitor, some characters (date, time, camera title, etc.) may not be
displayed on the screen.
• When [16:9 mode] is selected for “Image capture mode”, the top and bottom of the image on
the monitor will be displayed in black.
Note:
• The monitor out is set to NTSC in the default settings of the camera. If you want to change the
monitor out setting to PAL, refer to the Operating Instructions on our support website.

11
■ Indicators and buttons
CACT indicator
BLINK indicator
DSD MOUNT indicator
AINITIAL SET button
GTELE button
HWIDE button
FSD ON/OFF button
ESD memory card
warning/error indicator
A INITIAL SET button (Initializing / NTSC PAL switch button)
Follow the steps below to initialize the network camera.
(1)Turn off the power of the camera. When using a PoE hub, disconnect the Ethernet cable
from the camera.
When using an external power supply, disconnect the 2P power cable (WV-QCA501A
accessory) from the power supply cable (12V DC).
(2)Turn on the power of the camera while pressing the INITIAL SET button, and make sure to
release the button after approximately 15 seconds. In about 2 minutes later, the camera will
start up and the settings including the network settings will be initialized. Retry if the camera
does not start up normally.
IMPORTANT:
• When the camera is initialized, the settings including the network settings will be initialized.
Before initializing the settings, it is recommended to write down the settings in advance.
• Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
• When the INITIAL SET button is pressed (less than 1 second) to switch the output signal of the
MONITOR OUT terminal, the MONITOR OUT terminal can be switched for the NTSC monitor
PAL monitor.
BLINK indicator
• When the camera is able to communicate with Lights orange
the connected device
CACT indicator
• When data is being sent via the network camera Blinks green (accessing)

12
DSD MOUNT indicator
• When a microSD memory card is inserted and could Lights off →Blinks green →
be recognized Lights off
• When data can be saved after the microSD memory Lights off →Lights green
card is inserted and the SD ON/OFF button is pressed
(less than 1 second)
• When data can be saved to the microSD memory card Lights green
• When the microSD memory card is removed after Lights green →Blinks green →
holding down the SD ON/OFF button (about 2 seconds) Lights off (recording)
Lights green →Lights off
(waiting for recording)
• When data cannot be saved to the microSD memory card Lights off
because an abnormality was detected or the microSD
memory card is configured not to be used
Note:
• Lighting/blinking LED can be turned off with the software settings at any time. (The initial
state is lighting or blinking.) Set the LED to be solid off if necessary, depending on the
installation conditions. ( Operating instructions on our support website)
ESD memory card warning/error indicator
• When a warning status is detected Lights red
*SD memory card warning detection conditions: After the total use time has exceeded 6 years
and the number of overwrite times has exceeded 2000.
• When an error status is detected Blinks red
*SD memory card error detection conditions: Write error, read error, etc.
Note:
• The default is off. According to the installation environment, set up with software as required.
(Operating instructions on our support website)
FSD ON/OFF button
(1)When the SD ON/OFF button is pressed (less than 1 second), the SD MOUNT indicator lights
up in green and data can be saved to the microSD memory card.
(2) When the SD ON/OFF button is held down (about 2 seconds), the SD MOUNT indicator lights off
and the microSD memory card can be removed.
GTELE button
Click the TELE button to adjust the zoom ratio to the “Tele” side.
HWIDE button
Click the WIDE button to adjust the zoom ratio to the “Wide” side.

13
Insert / remove a microSD memory card
Note:
• Use a microSD memory card dedicated to i-PRO cameras.
• Refer to the Operating Instructions on our support website for further information about the
microSD memory card settings.
■ Insert a microSD memory card
A Remove the front portion from the camera. (Refer to installation procedure leaflet)
B Insert the microSD memory card until it makes a clicking sound.
C Take your fingers off the microSD memory card and check that its back end does not
protrude over the side part of the camera.
D After the microSD memory card has been inserted, press the SD ON/OFF button, and
make sure the SD MOUNT indicator is continually lit.
If you do not press the SD ON/OFF button after inserting the microSD memory card, the
SD MOUNT indicator is automatically lit approximately 5 minutes later.
microSD memory card
SD MOUNT indicator
SD ON/OFF button
E Attach the front portion to the camera.

14
■ Remove a microSD memory card
When removing a microSD memory card, reverse the procedure.
• To remove the microSD memory card, hold down the SD ON/OFF button for about 2 seconds.
When the flashing SD MOUNT indicator goes out, you can remove the microSD memory card.
IMPORTANT:
• Before turning off the camera power switch, make sure that the SD MOUNT indicator is
turned off. If you turn off the camera power switch while the SD MOUNT indicator is lit or
flashing, the recorded data may be corrupted or damaged.
Note:
• Refer to the Operating Instructions for further information about the microSD memory card
settings.
• When using a microSD memory card, format it using this product. Recorded data on the
microSD memory card will be deleted when formatted. If an unformatted microSD memory
card or a microSD memory card formatted with other devices is used, this product may not
work properly or performance deterioration may be caused. Refer to the Operating
instructions for how to format a microSD memory card.
IMPORTANT:
• Note that the area around the IR LED
Light in the right figure may be hot
when you turn off the camera and
remove the front portion to take out the
microSD memory card.
IR LED Light
SD slot

15
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table
or a problem is not described below.
Symptom Cause/solution Reference
pages
Power is not turned
on.
When using a PoE device for power supply
• Are the PoE device (IEEE802.3af compliant) and the RJ45
Network connector connected using an Ethernet cable?
Check whether the connection is appropriately established.
• Depending on the PoE device, the power supply will stop
when the demanded power exceeds its total power limit
for all PoE ports.
Refer to the operating instructions of the PoE device in use. Installation
Guide
When using DC power supply
• Is the 2P power cable (WV-QCA501A accessory) firmly
inserted into the power supply cable of the camera?
Confirm the power plug is firmly connected.
• Is the AC adaptor in use compliant with the
Specifications?
Check the Specifications regarding AC adaptor.
The LINK indicator
does not light in
orange even when the
Ethernet cable is con-
nected to the camera.
• Is the Ethernet cable connected appropriately?
Connect the Ethernet cable appropriately.
• Is the hub or router connected to the camera operating
appropriately?
Check if the hub or router in use is operating appropriately.
• Is the Ethernet cable connected to the camera broken?
Replace the cable with another one.
11
The SD MOUNT indica-
tor does not light even
when a microSD mem-
ory card is installed.
This indicator lights up green when the microSD memory
card is recognized correctly and ready for use.
• Has the inserted microSD memory card been formatted
on a PC?
Use a microSD memory card formatted on the camera.
Or install the software to format the microSD memory card
on the PC. Refer to our website <Control No.: C0105>
for further information about the supported software.
11, 12
SD memory card warn-
ing/error indicator
lights red.
• The read/write error on the microSD card has occurred.
Is the inserted microSD memory card faulty?
Replace the card with a normal one.
11, 12
Troubleshooting

16
Symptom Cause/solution Reference
pages
Audio input contains
noise.
• Check the following.
• Grounding of the camera, a switching hub or periph-
eral devices are not done.
• The camera is used near an electrical power line.
• The camera is used near a device which produces
strong magnetic field or radio waves (such as near a
TV/radio antenna, a motor of an air conditioning sys-
tem, a transformer, etc.)
When audio input still contains noise even after checking
the above possibilities, use a powered microphone or
connect audio output with low output impedance.
Installation
Guide
Auto focus (AF) can
not be automatically
adjusted.
• In the following locations or with the following subjects,
the focus may not be able to be automatically adjusted.
In this case, manually adjust the focus from the software
screen.
• When the subject moves a lot
• When there are large changes to the lighting intensity
• When the light level is low
• When the subject or location is extremely bright or
reflective
• When viewing through windows
• When the front panel is in a locations where it can
easily become dirty
• Locations where there is not much contrast such as a
white wall
• When there is harsh flickering
Operating
Instructions

17
Detail specifications
•Basic
Power source *1: DC 12 V
PoE (IEEE802.3af compliant)
Power consumption *1: DC 12 V: 900 mA/ Approx. 10.8 W
PoE DC 48 V: 220 mA/ Approx. 10.6 W (Class 0 device)
Operating environment
Ambient operating temperature:
Ambient operating humidity:
–40 °C to +60 °C *2{–40 °F to +140 °F}
(Power On range: –30 °C to +60 °C {–22 °F to +140 °F})
10 % to 100 % (no condensation)
Storage environment
Storage temperature:
Storage humidity:
–30 °C to +60 °C {–22 °F to +140 °F}
10 % to 95 % (no condensation)
Monitor output
(for adjustment):
VBS: 1.0 V [p-p]/75 Ω, composite, Pin jack
An NTSC or PAL signal can be outputted from camera
(either press the INITIAL SET button quickly (within 1 second) or
use software to select NTSC or PAL signal).
EXT I/O terminals: ALARM IN1
(Alarm input 1/ Black & white input/ Auto time adjustment input) (x1)
ALARM IN2 (Alarm input 2/ ALARM OUT) (x1)
ALARM IN3 (Alarm input 3/ AUX OUT) (x1)
Audio input: ø3.5 mm stereo mini jack
For microphone input: Recommended applicable microphone: Plug-in power type
(Sensitivity of microphone:–51 dB to -38 dB (0 dB=1 V/Pa, 1 kHz))
Input impedance: Approx. 2 kΩ (unbalanced)
Supply voltage: 2.5 V ±0.5 V
For line input: Input level: Approx. –10 dBV
Audio output *3:ø3.5 mm stereo mini jack (Audio output is monaural.)
Output impedance: Approx. 600 Ω (unbalanced)
Output level: –20 dBV
Waterproof *4: IP66 (IEC 60529), Type 4X (UL50E)
NEMA 4X compliant
Shock resistance: IK10 (IEC 62262)
Wind resistance: Up to 40 m/s {approx. 89 mph}
Dimensions: 133 mm (W) x 133 mm (H) x 383 mm (D)
{5-1/4 inches(W) x 5-1/4 inches(H) x 15-3/32 inches (D)}
Mass: Approx. 2.4 kg{5.3 lbs}
Finish: Main body: Aluminum die cast and resin, i-PRO white
Outer fixing screws :Stainless steel (Corrosion-resistant treatment)
Front panel: PC resin, Clear
*1 Refer to our technical information website <Control No.: C0106> for further information about Power
source and Power consumption information.
*2 When using with the IR LED Light constantly lit, the upper limit of the operating temperature range is
+50 °C {+122 °F}.
*3 The audio output can be switched to the monitor output. Refer to the “Operating Instructions” on our
support website for descriptions of how to switch the output.
*4 Only when installation work is properly performed according to the Installation Guide and appropriate
waterproof treatment is performed.

18
•Camera
Image sensor: Approx. 1/2.8 type CMOS image sensor
Effective pixels: Approx. 2.1 megapixels
Scanning area: 5.57 mm (H) × 3.13 mm (V) {7/32 inches (H) × 1/8 inches (V)}
Scanning system: Progressive
Minimum illumination: Color: 0.011 lx {0.00103 footcandle}
(30IRE, F1.7, Maximum shutter: Off (1/30 s), AGC: 11)*
0.015 lx {0.00139 footcandle}
(50IRE, F1.7, Maximum shutter: Off (1/30 s), AGC: 11)
0.001 lx {0.00009 footcandle}
(50IRE, F1.7, Maximum shutter: max. 16/30 s, AGC: 11)*
BW: 0 lx {0 footcandle}
(50IRE, F1.7, Maximum shutter: OFF (1/30 s), AGC: 11, when the
IR LED is lit)
0.008 lx {0.00074 footcandle}
(50IRE, F1.7, Maximum shutter: Off (1/30 s), AGC: 11)
0.0005 lx {0.00004 footcandle}
(50IRE, F1.7, Maximum shutter: max. 16/30 s, AGC: 11)*
* Converted value
Intelligent Auto: On/ Off
Super Dynamic
*1 : On/ Off
The level can be set in the range of 0 to 31.
Dynamic range: Max. 144 dB
(Super Dynamic: On, Level: 31)
Maximum gain: The level can be set in the range of 0 to 11.
Adaptive black stretch: The level can be set in the range of 0 to 255.
Back light compensation (BLC) /
High light compensation (HLC):
BLC/ HLC/ Off
The level can be set in the range of 0 to 31.
(only when Super Dynamic/ Intelligent Auto: Off)
Fog compensation: On/ Off
The level can be set in the range of 0 to 8.
(only when Intelligent Auto / Auto contrast adjust: Off)
Light control mode setting: Outdoor scene/ Indoor scene (50 Hz)/ Indoor scene (60 Hz)/ Fix shutter
Shutter speed: [60 fps mode]
1/60 Fix, 1/100 Fix, 1/120 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix,
1/2000 Fix, 1/4000 Fix, 1/10000 Fix
[30 fps/ 15 fps mode]
1/30 Fix, 3/120 Fix, 2/100 Fix, 2/120 Fix, 1/100 Fix, 1/120 Fix,
1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix
[50 fps mode]
1/50 Fix, 1/100 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix, 1/2000 Fix,
1/4000 Fix, 1/10000 Fix
[25 fps/ 12.5 fps mode]
1/25 Fix, 3/100 Fix, 2/100 Fix, 1/100 Fix, 1/250 Fix, 1/500 Fix,
1/1000 Fix, 1/2000 Fix, 1/4000 Fix, 1/10000 Fix

19
Maximum shutter: [60 fps mode]
Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,
Max. 1/250 s, Max. 1/120 s, Max. 1/100 s, Max. 2/120 s, Max. 1/30 s,
Max. 2/30 s, Max. 4/30 s, Max. 6/30 s, Max. 10/30 s, Max. 16/30 s
[30 fps/ 15 fps mode]
Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,
Max. 1/250 s, Max. 1/120 s, Max. 1/100 s, Max. 2/120 s, Max. 2/100 s,
Max. 3/120 s, Max. 1/30 s, Max. 2/30 s, Max. 4/30 s, Max. 6/30 s,
Max. 10/30 s, Max. 16/30 s
[50 fps mode]
Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,
Max. 1/250 s, Max. 1/100 s, Max. 2/100 s, Max. 1/25 s, Max. 2/25 s,
Max. 4/25 s, Max. 6/25 s, Max. 10/25 s, Max. 16/25 s
[25 fps/ 12.5 fps mode]
Max. 1/4000 s, Max. 1/2000 s, Max. 1/1000 s, Max. 1/500 s,
Max. 1/250 s, Max. 1/100 s, Max. 2/100 s, Max. 3/100 s, Max. 1/25 s,
Max. 2/25 s, Max. 4/25 s, Max. 6/25 s, Max. 10/25 s, Max. 16/25 s
Color/BW: Off/ On(IR Light Off)/ On(IR Light On)/
Auto1(IR Light Off)/ Auto2(IR Light On)/ Auto3(SCC)
IR LED Light: High/ Middle/ Low/ Off
Maximum irradiation distance: 70 m {Approx. 230 ft} (30IRE)*
50 m {Approx. 164 ft} (50IRE)
* Converted value
White balance: ATW1/ ATW2/ AWC
Digital noise reduction: The level can be set in the range of 0 to 255.
Privacy zone: On/ Off
Up to 8 zones available
VIQS: On/ Off
Up to 8 zones available
Camera title on screen: On/ Off
Up to 40 characters, Up to 2 lines (alphanumeric characters, marks)
Video Motion Detection (VMD): On/ Off
4 areas available
Scene Change Detection (SCD): On/ Off
1 area available
Audio Detection: On/ Off
AI Sound classification: Selectable from Gunshot, Yell, Vehicle horn, Glass break
Image rotation*2*3*4:0° (Off)/ 90°/ 180° (Upside-down)/ 270°
*1 When 60 fps or 50 fps is selected, the Super Dynamic function is automatically set to off.
*2 When the 320x180 resolution is used, the “90°” and “270°” settings are not available.
*3 The analog output from the MONITOR OUT terminal will not rotate even when “90 °” or “270 °” is
selected for [Image rotation].
*4 When [16:9 mode(30 fps mode)] or [16:9 mode(25 fps mode)] is used, the “90°” and “270°” settings
are available.

20
•Lens
Zoom ratio:
Optical zoom
Extra optical zoom
2.3x (Motorized zoom / Motorized focus)
max 6.9x
(2.3x – 6.9x when resolution is 640x360)
Focal length: 9 mm – 21 mm {11/32inches – 13/16inches}
Maximum aperture ratio: 1:1.7 (WIDE) – 1:3.0 (TELE)
Focus range: 2 m {78-3/4 inches} – ∞
Aperture range: F1.7 – T405
Angular field of view: [16:9 mode]
Horizontal: 15° (TELE) – 36° (WIDE)
Vertical: 9° (TELE) – 20° (WIDE)
[4:3 mode]
Horizontal: 11° (TELE) – 27° (WIDE)
Vertical: 9° (TELE) – 20° (WIDE)
DORI *1:
Detect (25 ppm / 8 ppf)
Observe (62.5 ppm / 19 ppf)
Recognize (125 ppm / 38 ppf)
Identify (250 ppm / 76 ppf)
291.7 m {956.9 ft} (TELE) 118.2 m {387.7 ft} (WIDE)
116.7 m {382.8 ft} (TELE) 47.3 m {155.1 ft} (WIDE)
58.3 m {191.4 ft} (TELE) 23.6 m {77.5 ft} (WIDE)
29.2 m {95.7 ft} (TELE) 11.8 m {38.8 ft} (WIDE)
*1 Maximum distance at which a camera's tele and wide lens can meet DORI specifications. This
value does not indicate the performance of the camera. Calculations made with the camera
installed horizontally at resolution of maximum resolution.
•Camera mount bracket
Adjusting angle: <Ceiling mounting>
Horizontal: ±180° (Adjust by horizontal (PAN) angle)
Vertical: 0° to 100° (Adjust by vertical (TILT) angle)
Yaw: –190° to +100° (Adjust by azimuth (YAW) angle)
<Wall mounting>
Horizontal: ±100° (Adjust by vertical (TILT) angle)*
Vertical: ±100° (Adjust by vertical (TILT) angle)*
Yaw: –190° to +100° (Adjust by azimuth (YAW) angle)
* You can change between horizontal and vertical angels by
adjusting the horizontal (PAN) angle.