i-PRO WV-S71300-F3 User manual

Operating Instructions
Network Camera
Model No. WV-S71300-F3
WV-S71300-F3
•The model number is abbreviated in some descriptions in this manual.

Preface
About the user manuals
There are 3 sets of operating instructions as follows.
•Operating Instructions (this document): Explains how to perform the settings and how to operate this
camera.
•Basic Information: Provides information about “Precautions for use” , “Parts and functions” and “Detail
specifications”.
•Installation Guide, Installation Procedure: Provides information about “Precautions”, “Precautions for
installation” and the installation method.
The screens used in these operating instructions show the case of WV-S71300-F3. Depending on the model
used, the screens shown in the explanations may differ to the actual camera screens.
This document provides how to operate and configure the camera using a web browser but it is recommended
to use the i-PRO Configuration Tool to configure the camera. The i-PRO Configuration Tool can configure up
to 1024 cameras at the same time so that the cameras can be configured efficiently.
For information about the i-PRO configuration tool (iCT), refer to our technical information website <Control
No.: C0133>.
Note
•“<Control No.:C****>” used in this document should be used to search for information on our technical
information website
(https://i-pro.com/global/en/surveillance/training_support/support/technical_information) and will
guide you to the right information.
•The captured screens are used based on the guideline by Microsoft Corporation.
•Operations using Google Chrome is described in this document. For information on the operation
verification of the supported web browsers, refer to our technical information website <Control No.:
C0132>
•The default settings of some of the stream-related settings vary as follows depending on the language
setting of the browser selected at the time of administrator registration.
Setting items
Language of the browser
Languages other than
Japanese Japanese
Transmission priority VBR Frame rate
Image quality 3 Normal
Stream(1)
-Max bit rate (per client)
6144kbps * 3072kbps *
Stream(1)
-Smart VIQS
On(Low) Off
Stream(2)
-Max bit rate (per client)
4096kbps * 2048kbps*
Stream(3)
-Max bit rate (per client)
1536kbps * 768kbps *
Stream(4)
-Max bit rate (per client)
1536kbps * 768kbps *
2 Operating Instructions
Preface

Stream(1) - Stream(4)
-Refresh interval
2s 1s
Abbreviations
The following abbreviations are used in these operating instructions.
Microsoft Windows 11 is described as Windows 11.
Microsoft Windows 10 is described as Windows 10.
microSDXC/microSDHC/microSD memory card is described as SD card or SD memory card.
Universal Plug and Play is described as UPnP™ or UPnP.
About the initial setting
1 Administrator registration
At the time of first access to the camera (or at the time of initialization), the registration screen will be displayed.
Define the user name and the password for the administrator, and enter them correctly. Hereafter, they can
be used for login.
[User name (1 to 32 characters)]
Enter the user name of the administrator.
•Available number of characters: 1 - 32 characters
Operating Instructions 3
Preface

•Unavailable characters: 2-byte characters, and 1-byte symbols " & : ; \
[Password (8 to 32 characters)]/[Retype password]
Enter the administrator password.
•Available number of characters: 8 - 32 characters
•Unavailable characters: 2-byte characters, and 1-byte symbols " &
Note
•Distinguish between upper- and lower cases.
•For the password, use three or more types of characters from upper- and lowercase alphabetic
characters, numeric characters, and symbols.
•Set the password which does not include the user name.
IMPORTANT
•If you forgot or do not know the password or user name, the camera must be initialized. Because all
settings other than preset position settings are deleted when the camera is initialized, make sure to
keep the information secure from third parties. Refer to “Parts and functions” section in the Basic
Information for more information about initializing the camera.
•It is recommended to change the password periodically.
•Do not use the password already used for other camera or device.
The language/time and date setting screen will be displayed after registering a user name and password of
the administrator.
2 Language/time and date setting
Language/time and date setting
4 Operating Instructions
Preface

[Menu language]
Select the language to initially display when the camera is accessed from the following.
Auto/English/Japanese/Italian/French/German/Spanish/Chinese/Russian/Portuguese
•Auto: The language used by the browser is automatically selected. If the language used by the browser
is not supported by the camera, English is selected.
•Default: Auto
[Date/time display]
Select “On” or “Off” to determine whether or not to display the date and time on an image. To hide the date
and time, select “Off“.
•Default: On
[Time display format]
Select the time display format from “24h” and “12h”.
•Default: 24h
[Date/time display format]
Select a date/time display format. When “2022/04/01 13:10:00” is set for “Date/time” after selecting “24h” for
“Time display format”, time & date will be respectively displayed as follows.
•DD-MM-YYYY: 01/04/2022 13:10:00
•MM-DD-YYYY: 04/01/2022 13:10:00
•DD-Mmm-YYYY: 01/Apr/2022 13:10:00
•YYYY-MM-DD: 2022/04/01 13:10:00
•Mmm-DD-YYYY: Apr/01/2022 13:10:00
•Default: Mmm-DD-YYYY
[Date]
Click the button and set a date on the camera.
When is clicked, the date and time on the PC will be acquired and displayed.
•Available range: Jan/01/2013 - Dec/31/2035
[Time]
Click the button and set a time on the camera.
When is clicked, the time on the PC will be acquired and displayed.
IMPORTANT
•Use an NTP server when the more accurate time & date setting is required for the system operation.
(®“3.10.2.3 Configure the settings relating to the NTP server”)
[Date/time position]
Select the position to display the time and date in an image. When the “Apply the setting of Cam. 1 to Cam.
2, 3, 4” check box is checked, the changed setting of camera 1 will be applied to all other cameras.
•Upper left: The information will be displayed at the upper left corner of the screen.
•Lower left: The information will be displayed at the lower left corner of the screen.
•Upper center: The information will be displayed at the upper center of the screen.
•Lower center: The information will be displayed at the lower center of the screen.
•Upper right: The information will be displayed at the upper right corner of the screen.
•Lower right: The information will be displayed at the lower right corner of the screen.
•Default: Upper left
Operating Instructions 5
Preface

[Set PC time to the camera]
If you select the checkbox and click the [Set] button, the date and time on the PC is acquired and set on the
camera.
[Time zone]
Select a time zone corresponding to the location where the camera is in use.
•Default: (GMT +09:00) Osaka, Sapporo, Tokyo
[Summer time (daylight saving)]
Select “In”, “Out” or “Auto” to determine whether or not to apply daylight saving time. Configure this setting if
the summer time (daylight saving time) is applied in the location where the camera is in use.
•In: Applies summer time. An asterisk (*) will be displayed on the left side of the displayed time and date.
•Out: Does not apply summer time.
•Auto: Applies summer time in accordance with the settings for “Start time & date” and “End time &
date” (month, week, day of the week, time).
•Default: Out
[Start time & date] [End time & date]
When “Auto” is selected for “Summer time (daylight saving)”, select the time & date for the start time and the
end time (month, week, day of the week, time).
Screen setting
[Color]
Select “Light” or “Dark” for the background color of each menu of the operation panel (®“ 1.1.2 About the
“Live” page”) and the detailed setting menu (®“3 Detailed Settings”).
•Default: Light
[Operation panel layout]
Select “Right”, “Left” or “Bottom” for the layout position of the operation panel (®“1.1.2 About the “Live”
page”).
•Default: Bottom
6 Operating Instructions
Preface

Table of Contents
1 Operations ..............................................................................................10
1.1 Monitor images on a PC .................................................................................................10
1.1.1 Monitor images from a single camera ............................................................................10
1.1.2 About the “Live” page .....................................................................................................12
1.1.3 Monitor images from multiple cameras ..........................................................................16
1.2 Monitor images on a mobile terminal or tablet device ................................................18
1.2.1 Monitor images on a mobile terminal (smartphone, etc.) ...............................................18
1.2.2 Monitor images on a tablet device ..................................................................................20
1.3 Record images on the SD memory card manually ......................................................24
1.4 Action at an alarm occurrence .......................................................................................25
1.4.1 Alarm type ......................................................................................................................25
1.4.2 Action at an alarm occurrence ........................................................................................25
1.5 Display the log list ..........................................................................................................27
1.6 Playback of images on the SD memory card ...............................................................30
1.6.1 Playback “JPEG(1)”/“JPEG(2)” images saved to the SD memory card .........................30
1.6.2 Playback “Stream(1)”/“Stream(2)”/“Stream(3)”/“Stream(4)” images saved to the SD
memory card ..................................................................................................................32
2 Settings ...................................................................................................35
2.1 Display the settings panel from a PC ............................................................................35
2.1.1 How to display the settings panel ...................................................................................35
2.1.2 How to operate the setup menu .....................................................................................35
2.1.3 About the settings panel .................................................................................................36
3 Detailed Settings ....................................................................................38
3.1 About the network security ............................................................................................38
3.1.1 Equipped security functions ...........................................................................................38
3.2 Display the setup menu from a PC ................................................................................39
3.2.1 How to display the setup menu ......................................................................................39
3.2.2 How to operate the setup menu .....................................................................................39
3.2.3 About the setup menu window .......................................................................................41
3.3 Perform management of the extension software and the schedule setting [Ext.
software] ..........................................................................................................................43
3.3.1 Perform the installation, uninstallation and version upgrade of the extension software
[Software mng.] ..............................................................................................................43
3.3.2 Set a schedule of the extension software [Operation sched.] ........................................46
3.3.3 Check the control log of extention software [Control log] ...............................................47
3.4 Use Easy Setup [Easy Setup] ........................................................................................48
3.4.1 Configure the Internet settings [Internet] ........................................................................48
3.4.2 Configure an event action [Event action] ........................................................................50
3.4.2.1 Configure the schedule/alarm (event function type setup menu) ................................51
3.4.2.2 Alarm: Configure VMD, SCD, and audio detection (alarm setup menu) .....................52
3.4.2.3 Alarm: Configure the alarm function type (Alarm function type setup menu) ..............53
3.4.2.4 Alarm: Configure the details for recording conditions ..................................................54
3.4.2.5 Alarm: Configure the mail notifications and mail server ..............................................56
3.4.2.6 Schedule: Configure SD recording or SFTP periodic image transmission (schedule
function type setup menu) ...........................................................................................58
3.4.2.7 Schedule: Set SD memory recording (video recording setup menu) ..........................59
3.4.2.8 Schedule: Configure SFTP periodic image transmission (SFTP periodic image
transmission setup menu) ...........................................................................................60
3.5 Configure the basic settings of the camera [Basic] ....................................................63
3.5.1 Configure the basic settings [Basic] ...............................................................................63
Operating Instructions 7
Table of Contents

3.5.2 Configure the settings relating to the SD memory card [SD memory card] ....................67
3.5.3 Configure the settings relating to alteration detection [Alteration detection] ..................74
3.5.4 How to configure alteration detection settings ................................................................77
3.5.5 Configure the overlay image function [Overlay image] ...................................................77
3.6 Configure the settings relating to images and audio [Image/Audio] .........................80
3.6.1 Configure the settings relating to the image capture mode [Image] ...............................80
3.6.2 Configure the settings relating to JPEG images [Image] ................................................80
3.6.3 Configure the settings relating to Stream [Image] ..........................................................82
3.6.4 Configure the settings relating to image adjust, privacy zone, VIQS, and lens distortion
compensation [Image quality] .........................................................................................88
3.6.4.1 Configure the settings relating to image quality (“Image adjust” setup menu) ............89
3.6.4.2 Set mask areas ............................................................................................................95
3.6.4.3 Adjust the angular field of view using the Extra optical zoom function ........................97
3.6.4.4 Configure the settings relating to the privacy zone (“Privacy zone” setup
menu) ..........................................................................................................................98
3.6.4.5 Configure the VIQS setting ..........................................................................................99
3.6.4.6 Configure the VIQS area ...........................................................................................101
3.6.4.7 Register the initial installation angle of view ..............................................................102
3.6.5 Configure the settings relating to audio [Audio] ............................................................103
3.7 Configure the multi-screen settings [Multi-screen] ...................................................105
3.8 Configure the alarm settings [Alarm] ..........................................................................107
3.8.1 Configure the settings relating to the alarm action [Alarm] ...........................................107
3.8.2 Configure the settings relating to the camera action on alarm occurrence
[Alarm] ..........................................................................................................................108
3.8.2.1 Configure settings relating to alarm E-mail notifications ............................................108
3.8.2.2 Configure settings relating to SFTP transmission when an alarm occurs .................109
3.8.2.3 Configure settings relating to recording to an SD memory card when an alarm
occurs ........................................................................................................................109
3.8.2.4 Configure settings relating to TCP alarm notification when an alarm occurs ............109
3.8.2.5 Configure settings relating to HTTP alarm notification when an alarm occurs ..........109
3.8.2.6 Configure settings relating to SNMP transmissions of alarm images ........................109
3.8.3 Configure the VMD settings [VMD area] ......................................................................110
3.8.4 Set the VMD areas [VMD area] ....................................................................................113
3.8.5 Configure the SCD settings [SCD area] .......................................................................114
3.8.6 Set the SCD areas [SCD area] .....................................................................................116
3.8.7 Configure the settings relating to the audio detection [Audio detection] ......................117
3.8.8 Configuration of the settings relating to alarm notification [Notification] .......................118
3.8.8.1 Configure the settings relating to TCP alarm notification ..........................................118
3.8.8.2 Configure the settings relating to HTTP alarm notification ........................................120
3.9 Configure the settings relating to the authentication [User mng.] ...........................121
3.9.1 Configure the settings relating to the user authentication [User auth.] .........................121
3.9.2 Configure the settings relating to the host authentication [Host auth.] .........................123
3.9.3 Configure IEEE 802.1X [IEEE 802.1X] .........................................................................124
3.9.4 Configure the data encryption settings [Data encryption] .............................................127
3.10 Configuring the network settings [Network] ..............................................................130
3.10.1 Configure the network settings [Network] .....................................................................130
3.10.2 Configure advanced network settings [Advanced] .......................................................134
3.10.2.1 Configure the settings related to sending E-mails .....................................................134
3.10.2.2 Configure SFTP .........................................................................................................137
3.10.2.3 Configure the settings relating to the NTP server ......................................................141
3.10.2.4 Configure the UPnP settings .....................................................................................142
3.10.2.5 Configure the HTTPS settings ...................................................................................142
3.10.2.6 Configure the settings relating to DDNS ....................................................................144
3.10.2.7 Configure the settings relating to SNMP ...................................................................144
3.10.2.8 Configure the QoS settings .......................................................................................148
8 Operating Instructions
Table of Contents

3.10.2.9 Configure the SRTP settings .....................................................................................149
3.10.2.10 Configure the MQTT settings ....................................................................................149
3.10.2.11 Configure the LLDP settings ......................................................................................151
3.10.3 How to configure HTTPS settings ................................................................................152
3.10.4 How to configure the settings relating to DDNS ...........................................................152
3.10.4.1 Configuration of the DDNS service (Example of the “Viewnetcam.com”
service) ......................................................................................................................153
3.10.4.2 When using “Dynamic DNS Update” .........................................................................156
3.10.4.3 When using “Dynamic DNS Update(DHCP)” ............................................................156
3.11 Configure the settings relating to the schedules [Schedule] ...................................158
3.11.1 How to delete the set schedule ....................................................................................160
3.12 Maintenance of the camera [Maintenance] .................................................................161
3.12.1 Check the system log [System log] ..............................................................................161
3.12.2 Upgrade the firmware [Upgrade] ..................................................................................161
3.12.3 Check the status [Status] .............................................................................................162
3.12.4 Reset the settings/Reboot the camera [Default reset] ..................................................165
3.12.5 Settings data/backing up or restoring logs [Data] .........................................................165
3.13 Display our support website [Support] .......................................................................167
4 Others ....................................................................................................168
4.1 About the displayed system log ..................................................................................168
4.2 Troubleshooting ............................................................................................................174
4.3 Directory structure of SD memory card ......................................................................181
Operating Instructions 9
Table of Contents

1 Operations
1.1 Monitor images on a PC
The following are descriptions of how to monitor images from the camera on a PC.
1.1.1 Monitor images from a single camera
1. Start up the web browser.
2. Enter the IP address designated using the “IP Setting Software” in the address box of the browser.
•Example when entering an IPv4 address: http://URL registered using IPv4 address
http://192.168.0.10/
•Example when entering an IPv6 address: http://[URL registered using IPv6 address]
http://[2001:db8::10]/
<Example of IPv4 access>
IMPORTANT
•When the HTTP port number is changed from “80”, enter “http://IP address of the camera + : (colon)
+ port number” in the address box of the browser. (Example: http://192.168.0.11:8080)
•When this camera is in a local network, configure the proxy server setting ([Settings] ® [Network
and Internet] ® [Proxy]) not to use the proxy server for the local address.
Note
•Refer to <Control No.: P0002> and <Control No.: P0003> in the support video page of the support
site below for more information if [HTTPS] is selected for [HTTPS] - [Connection] on the
[Advanced] tab of the network page (®“3.10.1 Configure the network settings [Network]”).
https://i-pro.com/global/en/surveillance/training-support/support/technical-information#Network
3. Press the [Enter] key on the keyboard.
→The window with the user name and password entry fields will be displayed.
10 Operating Instructions
1 Operations

Note
•When “Off” is selected for “User auth.”, the authentication window will not be displayed before
displaying live images for the user name and password entries.
4. Click the [OK] button after entering the user name and the password.
→The “Live” page will be displayed. Refer to “1.1.2 About the “Live” page” for further information about
the “Live” page.
IMPORTANT
•It is recommended to change the password periodically.
•When displaying multiple H.265 (or H.264) images on a PC, images may not be displayed depending
on the performance of the PC.
Note
•The maximum number of concurrent access user is 14 including users who is receiving H.265 (or H.
264) images and users who are receiving JPEG images. Depending on the set values for “Bandwidth
control(bit rate)” and “Max bit rate (per client)*”, the maximum concurrent access number may be 14
or less users. When 14 users are concurrently accessing, the access limit message will be displayed
for users who subsequently attempt to access.
•If you set the “Stream transmission” (®“Stream(1)/ Stream(2)/ Stream(3)/ Stream(4)”) to “On”, an H.
265 (or H.264) image will be displayed based on the settings of the “Stream encoding format”. If you
set the “Stream transmission” (®“Stream(1)/ Stream(2)/ Stream(3)/ Stream(4)”) to “Off”, a JPEG image
will be displayed. A JPEG image can be displayed even if the “Stream transmission” is set to “On”, but
in that case, the transmission interval of the JPEG image will be restricted as follows.
Image capture mode Stream transmission
On Off
4:3 mode(30fps mode) max. 5 fps max. 30 fps
16:9 mode(30fps mode)
4:3 mode(25fps mode) max. 4.2 fps max. 25 fps
16:9 mode(25fps mode)
4:3 mode(15fps mode) max. 5fps max. 15fps
4:3 mode(12.5fps mode) max. 4.2fps max. 12.5fps
•The refresh interval may become longer depending on a network environment, PC performance,
photographic subject, access traffic, etc.
Operating Instructions 11
1 Operations

1.1.2 About the “Live” page
Note
•The buttons and setting items displayed on the “Live” page can be changed depending on the user
rights of the accessing user. You can set the user right settings from “User auth.” under “User mng.”.
(®“3.9.1 Configure the settings relating to the user authentication [User auth.]”)
O
A B C D E F G H I J K
N
M
L
Q
T S R
P
Camera title
The camera title entered for “Camera title” on the [Basic] tab will be displayed. (®“[Camera title]”)
SD recording status indicator
The status of the SD recording can be checked with this indicator.
When the SD recording starts, the SD recording status indicator will light red. It will go off when the SD
recording stops.
This indicator will be displayed when “Manual” or “Schedule” is selected for “Save trigger” on the setup
menu. (®“3.5.2 Configure the settings relating to the SD memory card [SD memory card]”)
Snap shot button
Click this button to take a picture (a still picture). The picture will be displayed on a newly opened window.
When right-clicking on the displayed image, the image can be saved using a function of the web browser.
Note
•When it takes longer than the specified period to obtain the snap shot picture due to the network
environment, the snap shot picture may not be displayed.
•If the image capture size specified for JPEG cannot be obtained, JPEG images are displayed with
the image capture size that could be obtained.
12 Operating Instructions
1 Operations

Therefore, when JPEG images obtained with snap shot are displayed on a PC, the displayed image
size may differ from the captured sized.
Stream selection display button
The stream selection screen is displayed as a popover. On the stream selection screen, [Live view] and
others can be set.
Before/after image comparison switch button
Click the icon to acquire and display a still image. You can compare the acquired still image as the image
before changing image quality settings.
1:1: Displays the acquired still image and the latest image side by side in the same size.
1:2: Displays the acquired still image and the latest image side by side with the latest image doubled
in size.
Off: Displays only the latest image.
Support button
When this button is clicked, our technical information website will be displayed in a newly opened window.
Our technical information website contains technical information, FAQ, and other information.
Full screen button
A new window will open and images will be displayed on a full screen.
[Grid display] buttons
Select On/Off to determine whether or not to display the grid that can be used for position adjustment of
this product when using the extension software.
For the adjustable size for each extension software, refer to our technical information website <Control
No.: C0320>.
[Installation angle of view confirmation] button
The [Installation angle of view confirmation] button is displayed when the initial installation angle of view
is registered. (®“3.6.4.7 Register the initial installation angle of view”)
If you click the [Installation angle of view confirmation] button, an image showing the amount of deviation
from the position when registering the installation angle of view, the pitch direction of the camera, and the
roll direction is displayed in the main area.
It is a guide for returning to the original angle of view if it deviates from the angle of view at the time of
installation.
Correct the angle of view while moving the camera in the pitch and roll directions.
: indicates the pitch direction.
: indicates the roll direction.
: indicates the position closely matches that when the installation angle of view was registered.
: indicates the position when the installation angle of view was registered.
: indicates how far the position has moved from when the installation angle of view was registered.
IMPORTANT
•If you click the [Installation angle of view confirmation] button, the image showing the amount of
deviation from the position when registering the installation angle of view, the pitch direction of the
camera, and the roll direction is recorded when recording with an SD memory card.
Note
•Click again to turn off the display in the main area. It will also turn off automatically after it is
displayed for a while.
•If the deviation from the angle of view when installed is large, the display for the amount of deviation
may not work properly.
Camera control panel display button ( )
Switches between display and hide the camera control panel. On the camera control panel, [Brightness]
and others can be set.
Operating Instructions 13
1 Operations

[Setup] button ( )
Switches between display and hide the settings panel.
Stream selection display button - [Live view] pull-down menu
You can select and switch to the image to be displayed in the main area from the following:
Stream(1)/Stream(2)/Stream(3)/Stream(4)/JPEG(1)/JPEG(2)/Multi-screen
The image in the main area is displayed based on the contents set in Stream(1) – (4) (®“Stream(1)/
Stream(2)/ Stream(3)/ Stream(4)”), JPEG(1) – (2) (®“JPEG”), or Multi-screen (®“3.7 Configure the
multi-screen settings [Multi-screen]”).
Also the first stream displayed when you accessed the camera can be set from “Initial display stream” of
the [Image] tab. For “Multi-screen”, you can set the “Initial display” in the [Multi-screen] tab.
Stream selection display button - [Refresh interval] pull-down menu
This pull-down menu will be displayed only when a JPEG image is displayed. Use it to select the display
method of the JPEG image.
•MJPEG: Displays JPEG images successively as MJPEG (Motion JPEG).
•Refresh interval : 1s/Refresh interval : 3s/Refresh interval : 5s/Refresh interval : 10s/Refresh
interval : 30s/Refresh interval : 60s: Refreshes JPEG format (still images) images at the specified
interval.
Note
•Depending on the network environment or the PC used, JPEG format (still images) images may
not be refreshed at the specified interval. Depending on the browser and PC environment, a
previous still image may be seen like an afterimage.
•The [Refresh interval] pull-down on the “Live” page is not displayed for JPEG images with data
encryption set to “On”.
Stream selection display button - Stream information display
Displays the setup for stream encoding format, image capture size, bit rate, and frame rate for the live view
of a stream.
Note
•Displays the values set in the stream. The actual bit rate and frame rate vary depending on the
network environment and the used PC.
Main area
Displays images from the camera.
The current time and date will be displayed according to the settings configured for “Time display format”
and “Date/time display format”. (®“3.5.1 Configure the basic settings [Basic]”)
In addition, when being adjusted, the status of brightness (®“[Brightness status display]”) will be displayed
as well as the characters configured for “Camera title on screen” (®“[Camera title on screen]”).
When displaying H.265 with a high bit rate, the stream may display only i-frames.
Note
•When the camera is operated by a user with a low access level, images displayed on the screen
may be changed temporarily. This does not affect operation of the camera.
•Depending on the PC in use, screen tearing* may occur when the shooting scene drastically
changes due to the GDI restrictions of the OS.
*A phenomenon in which portions of the screen are displayed out of alignment.
•When the data encryption function is enabled, images cannot be monitored on the “Live” page.
Please use our supported devices.
Camera control panel - SD memory card − [Log/Play]
When the [Start] button is clicked, the log list will be displayed and images saved on the SD memory card
can be played. Refer to “1.5 Display the log list” for further information about the log list and for how to
play images on the SD memory card.
14 Operating Instructions
1 Operations

Alarm occurrence indication
When an occurrence notification occurs, a popover will be displayed. When the [x] button is clicked, the
popover will disappear. (®“1.4 Action at an alarm occurrence”)
Note
•Since the alarm occurrence indication is not coupled to recording images to the SD memory card,
forwarding E-mails, or other operations, check the settings of each operation separately.
Camera control panel - SD memory card − [Rec. on SD]
This item is available only when “Manual” is selected for “Save trigger” on the [SD memory card] tab.
(®“[Save trigger]”)
Click the [Start] button to manually record images on the SD memory card. Refer to “1.3 Record images
on the SD memory card manually” for descriptions of how to manually record images on the SD memory
card.
Camera control panel - Volume - [Mic input volume (Camera to PC)]
This item is available only when the settings are as follows. (®“3.6.5 Configure the settings relating to
audio [Audio]”)
•When “Mic input” is selected for “Audio transmission mode”
•When “AAC-LC” is selected for “Audio input encoding format”
The mic input volume can be adjusted in 4 steps (Off/Low/Middle/High) by clicking the button or the
button or by moving the volume cursor.
When the mic input button is clicked, the mic input (Camera to PC) will be turned on/off.
Note
•When “Audio volume control mode” is set to “Adjust Mic input” in the setup menu, the volume cursor
cannot be operated when using “Audio recording” or “Audio detection”.
•When the camera is restarted, the adjusted volume level (for the reception) will return to the level
that had been set on the [Audio] tab on the setup menu. (®“3.6.5 Configure the settings relating
to audio [Audio]”)
•If multiple camera browsers are open at the same time on the same computer, audio cannot be
heard from the camera browsers that were opened later. Please only access 1 camera at a time.
•If the network communication is unstable, audio input may stop. In this case, resume the mic input
by turning the mic input button off and on.
Camera control panel - [Brightness]
The brightness is adjustable from 0 to 255. Click the button to make the image brighter, or click the
button to make the image darker. When the button is clicked, the setting will be reset to the default.
Note
•If you adjust the brightness while recording, the recorded image may be affected.
Operating Instructions 15
1 Operations

1.1.3 Monitor images from multiple cameras
Images from multiple cameras can be displayed on a multi-screen. Images from 4, 9, and up to 16 cameras
can be displayed simultaneously. To display images on a multi-screen, it is necessary to register cameras in
advance. 4 cameras can be registered as a group and up to 4 groups (16 cameras) can be registered.
(®“3.7 Configure the multi-screen settings [Multi-screen]”)
IMPORTANT
•When 16 screens are used for the display, only still images (JPEG) can be refreshed.
Note
•For further information about “Network Camera Recorder with Viewer Software Lite”, which is suited
to viewing images from several cameras, refer to our technical information website <Control No.:
C0301>.
•When you have registered a camera with the authentication function enabled, it is necessary to access
the camera and register the user name of “Administrator” and password in the web browser in advance.
Refer to our technical information website <Control No.: C0302> for information about the terms and
conditions for use of multi-screen.
1. From the “Live view” pull-down menu in the “Live” page, select “Multi-screen”.
→Images from the registered cameras will be displayed on a selected multi-screen (screen can be split
up to 16 areas). The following are instructions when displaying on a 4-split screen.
AB
C
D
E
F
Camera title
If you click the camera title, live images from the corresponding camera will be displayed on the
“Live” page of the newly opened window.
Camera control bar
Can be used to get snap shot of JPEG images.
Stream selection display button - [Live view] pull-down menu
Select the image displayed in the main area.
Stream selection display button - [Layout] pull-down menu
Select from the pull-down menu to display images from cameras in multi-screens of 4 to 9 or even 16
screens.
16 Operating Instructions
1 Operations

Stream selection display button - [Refresh interval] pull-down menu
Select from the pull-down menu and switch between video (MJPEG) and still images (JPEG).
For still images (JPEG), select the refresh interval (Refresh interval : 1s/Refresh interval : 3s/Refresh
interval : 5s/Refresh interval : 10s/Refresh interval : 30s/Refresh interval : 60s) for camera images.
When the 16 screen layout is used, Refresh interval : 1s cannot be selected.
Stream selection display button - [Resolution] pull-down menu
Select the resolution from the pull-down menu to change it.
When you select “4 Screens” in the [Layout] pull-down menu, the image capture size of the camera
changes.
•Switching between 320x180 (default) and 640x360
Note
•The frame rate may drop depending on the network environment and number of accessing users.
•If the image capture size specified for JPEG cannot be obtained, a JPEG image with an image
capture size that could be obtained is displayed. Therefore, when JPEG images obtained with snap
shot are displayed on a PC, the displayed image size may differ from the captured sized.
•When in full screen display, click&centering and zoom are not available.
Operating Instructions 17
1 Operations

1.2 Monitor images on a mobile terminal or tablet
device
1.2.1 Monitor images on a mobile terminal (smartphone, etc.)
It is possible to connect to the camera using a mobile terminal via the Internet and monitor images (MJPEG
or JPEG) from the camera on the screen of the mobile terminal. It is also possible to refresh images to display
the latest image.
The compatible mobile terminals are shown as follows. (As of Jun, 2021)
–iPad, iPhone (iOS 8 or later)
–Android™ mobile terminals
When an Android terminal is used, an MJPEG format image is displayed by the Firefox browser, and a JPEG
format image is displayed by the standard browser.
IMPORTANT
•When the authentication window is displayed, enter the user name and password.
To enhance the security, it is recommended to change the password periodically. (®“3.9.1 Configure
the settings relating to the user authentication [User auth.]”)
Note
•It is necessary to configure the network settings of the mobile terminal in advance to connect to the
Internet and monitor images from the camera. (®“3.10 Configuring the network settings [Network]”)
1. Access to “http://IP address/cam”*1 or “http://Host name registered in the DDNS server/cam”*2 using a
mobile terminal.
→Images from the camera will be displayed.
B
A
Live images area
Displays images from the camera.
Operation buttons area
Displays buttons to operate those functions.
Note
•The operations button displayed on the mobile terminal screen may not be available depending on
the user rights and access level of the accessing user. To display the operations button, it is
necessary to set the user rights and access level (“User auth.” in “User mng.”). (®“3.9.1 Configure
the settings relating to the user authentication [User auth.]”)
18 Operating Instructions
1 Operations

2. Click the button of the function that you want to operate.
A
Each function is explained below.
Resolution control
The resolution can be changed by selecting a resolution setting from the buttons.
Images are displayed in the image capture size selected in “JPEG(1)” or “JPEG(2)” of [JPEG] on the
[Image] tab.
Note
•You can change the image size displayed on the mobile terminal by accessing the following addresses.
–Large display: http://IP address/cam/dl
–Medium display: http://IP address/cam/dm
–Small display: http://IP address/cam/ds
•When the resolution is changed by the resolution control, the displayed resolution changes but the
image size remains the same.
•When the HTTP port number is changed from “80”, enter “http://IP address: (colon) + port number/
cam”*1 in the address box of the browser. When using the DDNS function, access to “http://Host name
registered in the DDNS server: (colon) + port number/cam”*2.
•When “HTTPS” is selected for “HTTPS” - “Connection” on the [Advanced] tab of the “Network” page,
enter as follows.
“https://IP address: (colon) + port number/cam” or “https://Host name registered in the DDNS server:
(colon) + port number/cam”
•When the authentication window is displayed, enter the user name of an administrator or user and
password. Depending on the mobile terminal in use, password entry may be required each time the
screen is switched.
•It is impossible to send and receive audio using a mobile terminal.
•Depending on the mobile terminal in use, larger size images may not be displayed. In this case,
selecting a setting close to the lowest quality setting for “Image quality setting” of
“JPEG” (®“3.6.2 Configure the settings relating to JPEG images [Image]”) may sometimes solve this
problem.
•Depending on the mobile terminal in use or its contract plan, it may be impossible to access.
*1 IP address is the global WAN IP address of the router that can be accessed via the Internet. However, when accessing the same
LAN as the camera with a wireless compatible mobile terminal, the IP address is the local IP address.
*2 Only when accessing the camera via the Internet.
Operating Instructions 19
1 Operations

1.2.2 Monitor images on a tablet device
It is possible to connect to the camera using a tablet device via the Internet and monitor images (MJPEG or
JPEG) from the camera on the screen of the tablet device. It is also possible to refresh images to display the
latest image.
The compatible mobile terminals are shown as follows. (As of Jun, 2021)
–iPad, iPhone (iOS 8 or later)
–Android™ mobile terminals
When an Android terminal is used, an MJPEG format image is displayed by the Firefox® browser, and a JPEG
format image is displayed by the standard browser.
IMPORTANT
•When the authentication window is displayed, enter the user name and password.
To enhance the security, it is recommended to change the password periodically. (®“3.8.1 Configure
the settings relating to the alarm action [Alarm]”)
Note
•It is necessary to configure the network settings of the tablet device in advance to connect to the Internet
and monitor images from the camera. (®“3.9.1 Configure the settings relating to the user
authentication [User auth.]”)
•Depending on the device model, the same screen as the PC may be displayed. In that case, access
to “http://IP address/live/tab.html” or “http://Host name registered in the DDNS server/live/tab.html”.
1. Access to “http://IP address/” or “http://Host name registered in the DDNS server/” using a tablet device.
→Images from the camera will be displayed.
B C D
G
H
I
J
K
L
M
N
Setup menu
E
A
F
[Setup menu] button*1
Displays the setup menu.
Camera title
The camera title entered for “Camera title” on the [Basic] tab will be displayed. (®“3.5.1 Configure the
basic settings [Basic]”)
Alarm occurrence indication button*2
When an alarm occurs, the display flashes. When this button is clicked, this button will disappear.
(®“1.4 Action at an alarm occurrence”)
20 Operating Instructions
1 Operations