i-PRO WV-V2530LK User manual

Network Camera
Operating Instructions
Model No WV-V2530LK
WV-V2530L1
WV-V1330LK
WV-V1330L1
Version 1.0.2

i
Table of Contents
1. Network Connection ···········································································································2
2. Main Interface Introduction···································································································3
2.1 Log in ······················································································································3
2.2 Live Interface ············································································································6
2.3 Encode Setup ···········································································································7
2.3.1. Image Adjustment ····························································································8
2.4 System Menu ············································································································9
2.5 Video Window Function Option ·····················································································9
2.5.1. Zoom and Focus (WV-V2530L1, WV-V1330L1) ···················································· 10
3. Alarm····························································································································· 12
4. Playback (WV-V2530LK, WV-V2530L1, WV-V1330L1) ···························································· 13
4.1 Playback ················································································································ 13
4.1.1. Function of Play ····························································································· 14
4.1.2. Playback File································································································· 15
4.1.3. Playback Cut ································································································· 16
4.1.4. Record Type·································································································· 17
4.1.5. Progress Bar ································································································· 17
4.1.6. Assistant Function ·························································································· 17
4.2 Picture Playback ······································································································ 18
4.2.1. Play············································································································· 18
4.2.2. Playback File································································································· 19
4.2.3. Snapshot Type······························································································· 20
5. Log out ·························································································································· 21
6. Setup····························································································································· 22
6.1 Basic ····················································································································· 22
6.2 Image/Audio ··········································································································· 23
6.2.1. Image/Audio·································································································· 23
6.2.1.1 Image···································································································· 23
6.2.1.2 Snapshot ······························································································· 25
6.2.1.3 Overlay·································································································· 26
6.2.1.4 ROI······································································································· 28
6.2.1.5 Path······································································································ 28
6.2.1.6 Audio (WV-V2530LK) ··············································································· 29
6.2.2. Image adjust ································································································· 30
6.2.2.1 Picture··································································································· 30
6.2.2.2 Exposure ······························································································· 31
6.2.2.3 Backlight································································································ 32
6.2.2.4 White Balance(WB)·················································································· 33
6.2.2.5 Day & Night ···························································································· 34
6.2.2.6 IR Light·································································································· 34
6.2.3. Profile Management························································································ 35
6.2.4. Zoom and Focus (WV-V2530L1, WV-V1330L1) ···················································· 35
6.3 Network ················································································································· 36
6.3.1. TCP/IP ········································································································· 36
6.3.2. Connection ··································································································· 37
6.3.2.1 Connection····························································································· 37
6.3.2.2 ONVIF··································································································· 38
6.3.3. DDNS ·········································································································· 38
6.3.4. IP filter ········································································································· 39

ii
6.3.5. SMTP (Email) ································································································ 40
6.3.6. UPnP··········································································································· 41
6.3.7. SNMP ·········································································································· 42
6.3.8. Multicast······································································································· 44
6.3.9. 802.1x·········································································································· 45
6.3.10. QoS············································································································· 46
6.4 Event····················································································································· 47
6.4.1. Video Detection ····························································································· 47
6.4.1.1 VMD ····································································································· 47
6.4.1.2 Tampering ······························································································ 50
6.4.2. Audio Detection (WV-V2530LK) ········································································ 51
6.4.3. Alarm (WV-V2530LK)······················································································ 52
6.4.4. Abnormity (except WV-V1330LK) ······································································ 53
6.4.5. Notification···································································································· 54
6.5 Storage ·················································································································· 56
6.5.1. Schedule ······································································································ 56
6.5.1.1 Record Schedule ····················································································· 56
6.5.1.2 Snapshot Schedule ·················································································· 57
6.5.1.3 Holiday Schedule····················································································· 59
6.5.2. Destination···································································································· 59
6.5.2.1 Path······································································································ 59
6.5.2.2 Local (except WV-V1330LK) ······································································ 60
6.5.2.3 FTP ······································································································ 61
6.5.3. Record Control ······························································································ 61
6.6 System ·················································································································· 63
6.6.1. Account (User mng.) ······················································································· 63
6.6.1.1 User Name····························································································· 63
6.6.1.2 Group···································································································· 64
6.6.2. Default reset ································································································· 66
6.6.3. Import/Export ································································································ 66
6.6.4. Auto Maintain ································································································ 67
6.6.5. Upgrade ······································································································· 67
6.7 Information ············································································································· 68
6.7.1. Version········································································································· 68
6.7.2. Log·············································································································· 68
6.7.3. Online User··································································································· 69
7. Using the CD-ROM··········································································································· 70
7.1 About the CD launcher ······························································································ 70
7.2 Installing Panasonic “IP Setting Software” ····································································· 71
7.3 Installing the manuals ······························································································· 71
7.4 Installing the Viewer software ····················································································· 72
7.5 Configure the network settings of the camera using the Panasonic “IP Setting Software”········ 72

1
Welcome
Thank you for purchasing our network camera!
This operation manual is designed to be a reference tool for your system.
Open the accessory bag to check the items one by one.
Depending on the model used, the screens shown in the explanations may differ to the actual camera
screens.

2
1. Network Connection
These series network camera products support the Web access and management via PC.
Web includes several modules: monitor channel preview, system configuration, alarm and etc.
Follow the steps listed below for network connection.
• Make sure the network camera has connected to the network properly.
• Network camera IP address and PC IP address shall be in the same network segment. If there is router,
set the corresponding gateway and subnet mask.
• Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

3
2. Main Interface Introduction
2.1 Log in
Open IE and input network camera address in the address bar.
For example, if your camera IP is 192.168.0.10, then input http:// 192.168.0.10 in IE address bar. See
Figure 2-1.
Figure 2-1
The login interface is shown as below. See Figure 2-2.
Input your “User name” and “Password” to have been registered when you access the camera at first.
Note:
• Refer to “Network Configuration” in Installation Guide manual.
• For security reasons, change the password periodically.
Figure 2-2
Input your IP
address here

4
If it is your first time to login, you may see the interface window shown as in Figure 2-3
Figure 2-3
Click on “Please click here to download and install the plug-in”. The system pops up warning information to
ask you whether run or save this plug-in. See Figure 2-4.
Figure 2-4
You must either run or save the file to local and install it. Follow the following steps. See Figure 2-5.
Note:
• The displayed screens are different by the security settings on the PC.

5
Figure 2-5
When plug-in installation completes, the installation page closes automatically. The web-end will refresh
automatically, and then you can view video captured by the camera.
Figure 2-6

6
2.2 Live Interface
After you logged in, you can see the live monitor window. See Figure 2-7.
Figure 2-7
There are three sections:
• Section 1: Encode setup bar
• Section 2: “System” menu
• Section 3: Window function option bar
3
2
1

7
2.3 Encode Setup
The encode setup interface is shown as in Figure 2-8.
Figure 2-8
Refer to the following sheet for detailed information.
SN Parameter Function
1 Menu You can switch “Live” and “Setup” menu.
2 Stream You can switch Main, Sub Stream 1 and 2.
The compression under distribution is displayed by Stream change.
3 Protocol You can select stream media protocol from the dropdown list.
There are three options: TCP/UDP/Multicast
4 Digital Zoom • When the video is in the original status, click it you can select any
zone to zoom in. In the non-original status, you can drag the
zoom-in zone in specified range. Right click mouse to restore
previous status.
• Click it; you can use the middle button of the mouse to zoom
in/out the video size.
5 Image Adjustment You can adjust image quality.
1
7
2
3
4
5
6
8

8
6 Alarm It moves to an alarm setting screen.
7 Playback It moves to a playback screen.
(WV-V2530LK, WV-V2530L1, WV-V1330L1)
8 Logout Click the [Logout] button, system goes back to log in interface.
2.3.1. Image Adjustment
Click the [Image Adjustment] button to open picture setup interface. See Figure 2-9. This interface is
displayed under a display of Image Adjustment.
Figure 2-9
Refer to the following sheet for detailed information.
Parameter Function
Video setup It is to adjust monitor video
brightness. Note:
• All the operations here apply to WEB
end only.
• Go to [Setup] →[Image/Audio] or
[Image] →[Image adjust] to adjust
corresponding items.
It is to adjust monitor video
contrast.
It is to adjust monitor video
hue.
It is to adjust monitor video
saturation.
Reset
Restore brightness, contrast
saturation and hue to system
default setup.

9
2.4 System Menu
To display the “System” menu, click the [Setup] button as in Figure 2-10.
.
Refer to 6.1 Basic, 6.2 Image/Audio, 6.3 Network, 6.4 Event, 6.5 Storage, 6.6 System, and 6.7 Information
for detailed information.
WV-V2530LK
WV-V1330LK, WV-V2530L1, WV-V1330L1
Figure 2-10
2.5 Video Window Function Option
The interface is shown as below. See Figure 2-11.
Figure 2-11
Refer to the following sheet for detailed information.
SN Parameter Function
1 Original Size Click this button to go to original size. It is to display the actual size
of the video stream. It depends on the resolution of the bit stream.
2 Full Screen Click it to go to full-screen mode. Double click the mouse or click the
Esc button to exit the full screen.
1 2 3 4 5 6 7 8 9 10 11

10
3 Width and Height ratio Click it to restore original ratio or suitable window.
4 Fluency Adjustment There are three levels of fluency for you to select. The default is
Normal. You may select fluent mode in case connection is slow.
5 Zoom and Focus Click this button and the zoom and focus interface appears on
encode setup bar, as shown in Figure 2-12.
(WV-V2530L1, WV-V1330L1)
6 Snapshot You can snapshot important video by clicking on this button. All
images are memorized in system folder: ¥ picture download
(default).
You can go to [Setup] →[Image] →[Image] →[Path] to modify the
local record save path.
7 Record For manual record. All records are memorized in [Setup] →[Image]
→[Image] →[Path].
When connected to Panasonic’s recorder, record for Sub stream 2
may not work correctly.
8 Easy Focus Click it, you can see there are two parameters on the preview
video：AF Peak and AF Max.
AF Peak: It is to display the video definition during the focus
process.
AF Max: It is the most suitable value for the video definition.
The close the AF Peak and AF Max is, the better the focus effect is.
(WV-V2530L1, WV-V1330L1)
9 Audio output Turn on or off audio when you are monitoring. (WV-V2530LK)
10 Bidirectional talk Click it to start or end bidirectional talk. (WV-V2530LK)
11 Relay-out
(Alarm output)
It shows if there is any alarm output, status description is as follows:
Green: means there is alarm output.
White means alarm is over.
Click on the button to force alarm to be on or off. (WV-V2530LK)
2.5.1. Zoom and Focus (WV-V2530L1, WV-V1330L1)
Click this button and the zoom and focus interface appears on the encode setup bar, as shown in Figure
2-12. Refer to the following sheet for detail information to adjust zoom and focus configuration.
Note:
• Auto-focus after zoom focus adjustment.
• Disable the operation till finishing zoom and focus adjustment.

11
Figure 2-12
Parameter Function
Zoom Adjust the focal length of the lens by clicking or long pressing the [+]/[-] button or
moving the slider. Step length (Speed) is used to adjust the length of one step with one
click.
Focus Adjust the sharpness length of the lens by clicking or long pressing the [+]/[-] button or
moving the slider. Step length (Speed) is used to adjust the length of one step with one
click.
Auto Focus Click to adjust the image definition automatically.
Note:
Other lens operations are not allowed during the process of auto-focus.
Restore All Reset the lens to zero position to eliminate the accumulative error of lens.
Note:
Reset when the image adjustment is not clear or operating zoom focus many times.
Refresh Synchronize the location of drag slider of lens and zoom focus after hardware zoom
focusing.

12
3. Alarm
Click alarm function, you can see an interface is shown as in Figure 3-1.
Here you can set device alarm type and alarm sound setup.
Figure 3-1
Refer to the following sheet for detailed information.
Type Parameter Function
Alarm Type VMD System alarms when VMD alarm occurs.
SD Full System alarms when SD memory card is full.
(WV-V2530LK, WV-V2530L1, WV-V1330L1)
SD Error System records alarm info when SD memory card error happens.
(WV-V2530LK, WV-V2530L1, WV-V1330L1)
Tampering System alarms when tampering alarm occurs.
Audio Detection System records alarm when audio detection occurs. (WV-V2530LK)
External Alarm System records alarm when alarm inputs the device. (WV-V2530LK)
When alarm is triggered, there will be displayed on the “Alarm” menu and system automatically
records alarm info. The icon disappears when user clicks on the “Alarm” menu bar.
Note:
• If alarm interface is displayed, when alarm is triggered, there will be no image prompt, but alarm record
will be in list on the right.

13
4. Playback (WV-V2530LK, WV-V2530L1, WV-V1330L1)
Web client playback supports video playback and picture playback.
Note:
• Before playback, user shall set storage management as in Chapter 6.5.
4.1 Playback
The playback interface is shown as in Figure 4-1.
Figure 4-1
There are four sections:
• Section 1: Function of play
• Section 2: Playback file
• Section 3: Playback cut
• Section 4: Record type
• Section 5: Progress bar
• Section 6: Assistant function
2
3
4
1
6
5

14
4.1.1. Function of Play
The function of play is shown as in Figure 4-2.
Figure 4-2
Parameter Function
1. Play When you see this button, it means pause or not played record. Click on this
button, switch to normal play status.
2. Stop Click this button to stop playing.
3. Next Frame Click on this button to go to next frame.
Note:
• You shall pause record when you use this function.
4. Slow Click on this button to play slowly.
5. Fast Click on this button to play quickly.
6. Sound When this button displays, it means audio is silent. Click on this button to
switch back to normal.
7. Volume Click on left mouse to adjust volume.
1 2 3 4 5 6 7

15
4.1.2. Playback File
In calendar, blue date represents data currently has video record or snapshot. See Figure 4-3.
Figure 4-3
Parameter Function
File Type • Select “mp4”, as video playback.
• Select “jpg” as picture playback.
Data Source Select only SD card.
Step1
Click on data in blue, time axis displays record file progress bar in color. While, green represents normal
record, yellow represents motion detect record, red represents alarm record, and blue represents manual
record.
Step2
Click on certain time on progress bar, playback starts from this time. See Figure 4-4.
Figure 4-4
Step3
Click on file list in Figure 4-3, select date file will be displayed in list.
Step4
Double click on file in list, playback this file and display file size, start time and end time.
See Figure 4-5.

16
Figure 4-5
Parameter Function
Search
It means records within searched start time and end time on the date.
Download Record type is “mp4”, click on the [Download] button and download file to path in
Chapter 6.5.2.1.
Back Click on the [Back] button to go to calendar interface.
4.1.3. Playback Cut
Note:
• The playback cut function automatically pauses playing records since the playback cut and playback
functions cannot be used at the same time.
Step1
Click on the [Start Time] to cut on time axis. This time must be within progress bar range.
Step2
Move mouse to cut icon . You will be asked to select start time. Click on the cut icon as finish
cutting.
Step3
Click on playback cut end time on time axis. This time must be within progress bar range.
Step4
Move mouse to the cut icon , you will be asked to select end time. Click on the cut icon as

17
finish cutting.
Step5
Click on the [Save] button to save file cut to path in Chapter 6.5.2.1. See Figure 4-6.
Figure 4-6
4.1.4. Record Type
After checking record file type, only selected file will be displayed in progress bar and file list. Users can
also select the record type to be displayed via the dropdown box which is above the file list. See Figure 4-7.
Figure 4-7
4.1.5. Progress Bar
Figure 4-8
Parameter Function
24 hours Click on it, means video in past 24 hours.
2 hours Click on it, means video in past 2 hours.
1 hour Click on it, means video in past 1 hour.
30 min Click on it, means video in past 30 min.
4.1.6. Assistant Function
Video playback assistant function is shown in Figure 4-9.
Figure 4-9
Parameter Function
Zoom in
• Click on it, video in playback status if is in original size, user can zoom in
any area, If it is not in its original size, click on mouse to restore its
original size.
• Click on this button, you can scroll to zoom in.
Snapshot
Click on this button, you can snapshot video under playback status. Snapshot
will be saved to path in Chapter 6.5.2.1.