I-Sniper EL-750 User manual

Installation Manual
Please read this manual carefully before installation and operation of the product.
130809-1
powered by
VANDAL DAY/NIGHT DOME CAMERA
EL-750 I-SNIPER VANDAL DAY/NIGHT DOME CAMERA
Copyright 2013, IC REALTIME, LLC. Made in Korea.
· EL-750

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding-type
plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Use only attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods of
time.
13. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as the power supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
14. The power plug must be readily accessible so that the equipment can be easily
disconnected from the AC power.
15. The product is still connected to the AC power whenever it is plugged in to a live
power outlet, even if the receiver is turned off using the remote control or front
panel buttons.
16. Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
You must remember certain safety issues during installation and use of this equipment.
This guide provides various procedures and instructions. Some of these procedures
could result in injury or property damage if they are improperly performed.
Other procedures require additional attention.
In this guide, we use the following notation to inform you when you need to
pay attention to a safety or operational issue.
CAUTION
– These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
2 3
Important Safety Instructions Warning and Attention Symbols
For Your Safety
Designates a potential situation where the following may happen:
• Personal injury or death may occur.
• Equipment or property may be damaged.
Designates the following operational issues:
• Important operation or maintenance instructions follow.
• Additional attention is required.
Designates the following operational issues:
• Important operation or maintenance instructions follow.
• Additional attention is required.
The Class II equipment symbol means the equipment has
additional insulation and does not need to be grounded.
Designates the following operational issues:
• Important operation or maintenance instructions follow.
• Additional attention is required.

· Please read the manual carefully before the installation in order to make use the
camera to be set up correctly and to have the best picture quality.
· Please keep the manual in good condition for your future reference and service
application.
· Installation and services should only be carried out by an authorized personnel
according to local safety regulations.
· If any liquid or solid matter gets into the housing, immediately disconnect the camera
from power supply and have it checked by your authorized dealer before reusing.
· Avoid installing the camera at extremely hot or cold places.
·If you are not a certified person, never try to dismantle the camera. To avoid electric
shock, never remove the screws or covers. There are no parts inside that need
maintenance by the user. All maintenance should be carried by qualified personnel.
·Avoid installing the camera at a place of high humidity.
·Avoid installing the camera at the place exposed to gas or oil.
·Keep the top glass of the lens always clean in order to obtain the best picture quality
all the time. Be careful not to be stained by fingerprint.
· Don't face the camera directly toward sunlight or sunlight reflecting area.
CCD may go defective at this condition.
· Please give a special attention to keep the unit from dangerous drop or
external shock during the process of transportation or handling.
· Never try to touch the camera in wet hand. It may cause an electric shock.
·Do not expose the camera to radioactivity. It causes a serious damage on the CCD.
4 5
1. Precautions
Table of contents
1. Precautions ------------------------------------------------------------- 5
2. Limitation of liability --------------------------------------------------- 5
3. Disclaimer of warranty ----------------------------------------------- 6
4. Package ----------------------------------------------------------------- 6
5. Main Features --------------------------------------------------------- 7
6. Assembly overview -----------------------------------------------8~10
7. Troubleshooting ------------------------------------------------------11
8. Dimension (mm) ----------------------------------------------------- 12
9. Specification ---------------------------------------------------------- 13
10. OSD Manual for function control---------------------------14~17
This publication is provided “AS IS” without warranty of any kind, either express or
implied, including but not limited to, the implied warranties of merchantability, fitness
for any particular purpose, or noninfringement of the third party's right. This publication
could include technical inaccuracies or typographical errors. Changes are added to the
information herein, at any time, for the improvements of this publication and/or the
corresponding product(s).
2. Limitation of liability

6 7
Installation Manual
EL-750
Please read this manual carefully before installation and operation of the product.
poweredby
I-SNIPER VANDAL DAY/NIGHTDOME CAMERA
5. Main Features3. Disclaimer of warranty
4. Package
In no event shall seller be liable to any party or any person, except for replacement or
reasonable maintenance of the product, for the cases, including but not limited to
below :
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product;
(2) Personal injury or any damage caused by inappropriate use or negligent operation
of the user;
(3) unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any reason
or cause including any failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the
system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being
photogenic subject, due to violation of privacy with the result of that surveillance-
camera's picture, including saved data, for some reason, becomes public or is used
for the purpose other than surveillance.
Ø
35.0
12.0
Ø
106.5
Ø
135.0
12.0
Camera x1 Manual x1 Sticker x1
Torx Wrench x1
Plastic anchor x3
Machine Screw x3
M4x12L
Machine Screw x3
M4x5L
Junction box plate x3 O-Ring x3
Extra Video output x1 Tapping Screws x3
powered by
• 1/3” I-Sniper PIXIM DPS image sensor
• 690TVL / 960H Effective Pixels
• 2.8-12mm Vari-Focal Lens
• WDR (Wide Dynamic Range)
• 2D/3D Digital Noise Reduction
• DIS (Digital Image Stabilizer)
•True Day and Night (ICR)
• Intelligent Functions
• Highlight Eclipse Function
• Digital Zoom
• Motion Detection
• Privacy Masking
• RS-485 Interface (Pelco-D)
• 12VDC/24VA Power Input
I-Sniper, the most accurate chip in the world, is an imaging solution created exclusively by
Pixim for IC Realtime. I-Sniper cameras deliver clear, detailed images in real-world scenes,
night and day, even under challenging, mixed lighting conditions.
I-Sniper cameras have been custom tuned with camera settings specifically for
ICRealtime’s line of DVRs, resulting in 25-45% longer recording times vs. nonoptimized
3rd party cameras.

8 9
6-1. Installation
A. Surface Mount
6. Assembly overview
BNC Female
for Video
Dual power
(12V DC/24V AC)
Mountingscrews
M4*30L-3EA
Torx screws
M4*10L-3EA
Plastic anchors(if needed)
Ø4*30L-3EA
Drilling template
Assembly surface bottom
Assembly dome cover
RS-485
① Paste a Drilling Template on the ceiling or wall and drill screw points which will be
done for installation.
② Fix a Surface Mounting Base by using Tapping Screws with Ø 4 provided.
③ Point a Camera 3D Gimbal to a desired direction and assemble a dome cover to the
Surface Mounting Base with Torx Screws by using Torx Wrench provided.
B. Junction Boxes
Mountingscrews
PH M4*5L & Ø4 O_ring-3EA
Torx screws
M4*10L-3EA
Assembly surface bottom
Assembly dome cover
Electrical junction box
Junction boxscrews
FH M4*12L -4EA
(UNC 8-32x0.75 screws : not included)
① Fix a Surface Mounting Base and Junction plate Gang Junction Box by using Fixed
Screws with M4 provided.
② Assemble a dome cover to the Base with Torx screws.

10 11
a. Power cable
b. RS-485 : Same as above
c.Video output cable
(Red)
(Black)
* Caution
Please make sure to seal these places with a tape
tightly enough to prevent water smearing into the
cable.
A lot of actual damages are happening by doing
improper finish on the spot.
6-3. 3-Axis, Lens adjustment
Pan 360˚
Rotation 360˚
Tilt 180˚
※ Tool-free 3-Axis mounting mechanism
Perfect Tri-axis!
· Panning axis up to 360˚ degree
· Tilting axis up to 180˚ degree
· Rotation axis up to 360˚ degree
No need to use a tool for adjustment!
All adjustments are done quick and easy
by hand!
☞ NOTE
Angle adjustment from each of 3 different axis can be positioned to its maximum angle
of view so that the camera gets the full central picture at any location.
Zoom Knob
Focus Knob
OSD Switch
Extra Video output cable
·Focus Knob
LEFT Control : ∞
RIGHT Control : Near
· Zoom Knob
LEFT Control : Tele
RIGHT Control : Wide
· Extra video output
To enable an installer to check and adjust the camera set up via service monitor on
the spot.
Make sure to use a butyl tape. (Do not use a sealing material on those parts)
① It is useful to connect the cable ends from camera to the extension cable for
waterproof.
② Connect and tape the power cables (Power-Power/Ground-Ground).
③ Bind the power cables together with the tape. When DC-Jack is used,
tape the DC-DC joint.
④ Connect and tape the RS485 cables (RS485+ㅡTRX+ /RS485- ㅡTRX-)
⑤ Tape the BNC-BNC joint.
6-2. Waterproof processing of cable end connection

12 13
7. Troubleshooting
Problems Troubleshooting
Nothing appears on
the screen.
·Please check that the power cord and line connection
between the camera and the monitor are fixed properly.
·Please check that you have properly connected VIDEO
cable to the camera.
· VIDEO output jack. Check DC Iris cable on Lens is
properly connected.
The image on the screen is
dim.
· Is lens stained with dirt? Clean your lens with soft,
clean cloth.
·Set the monitor to proper condition.
·If the camera is exposed to too strong light, change
the camera position.
The image on the screen is
dark.
· Adjust the contrast feature of the monitor.
·If you have an intermediate device, set the
75Ω / Hi-Z properly (Please check the impedance)
The camera is not working
properly, and the surface of
the camera is hot.
· Please check that you have properly connected the
camera to an appropriate power source.
Color is not correct. · Please check the setting of WHITE BAL SETUP menu.
The screen flickers
continually.
·Please check that direction of camera is turned toward
the Sun.
RS-485
communication fails.
· Please check the polarity between RS-485 Control
Port and RS-485 cable.
· Please check if the initial value of the RS-485
Communication setup matches between camera and
OSD Controller or DVR.
·We recommend that you make ground connection
between camera and controller for safe communication
control.
485 Control Board Connection Port RS-485 Control Port
(+)CONNECTION TERMINAL(TRX+) 485+
(-)CONNECTION TERMINAL(TRX-) 485-
UART MODE RET PKTItem Camera ID BAUD RATE
Initial value 1 9600 8-NONE-1 ENABLE
* RS-485 Communication establishment initial value
· When RS-485 cable is not properly connected,
A warning message ‘ERROR RS-485 Connection.
Please reconnect and Reboot’ is displayed.Then please
turn off the power and connect the cable again.
◆Connecting to POWER
A. Power connection (Power supply: (DC12V / AC24V)
B. Power Cable (Extension)
As the table below, voltage drops as the wire is longer so that the use of an excessively
long power cable (or extension cable use) to the camera may affect the camera’s
performance.
A. Power supply
B. Power Cable
(Extension)
The recommended adapter specification for EL-750 is DC12V/3A, AC24V/1A over.
Please check the standard power requirement before connecting the power.
The resistance value of Copper Wire : 25’C (77’F)
· Standard Voltage for proper camera operation is DC12V +/- 10% / AC24V +/- 10%
· AWG #24 : 10M is the maximum cable distance for proper operation.
Longer than 10 Meters, it may cause a damage to the product.
The manufacture is not liable for problems caused by an authorized
installation.
· AWG26, AWG28: It is not recommended. It causes a severe damage to the camera.
*Caution
a. There may be a deviation in voltage drop depending on the type of wire and its
manufactuer.
b. Please Do connect one camera by the input power! No other devices!
c. Please power on after installation finished.
Copper wire Size
(AWG)
Resistance ( Ω/m)
Voltage Drop(V/m)
1.3㎟
(#16)
0.83㎟
(#18)
0.52㎟
(#20)
0.33㎟
(#22)
0.22㎟
(#24)
0.01
0.019
0.03
0.03
0.04
0.049
0.06
0.068
0.1
0.113

14 15
8. Specification
7. Dimension(mm)
■Specifications are subject to change without prior notice to enhance performance and stability.
General
Image sensor 1/3”Pixim WDR digital image device
Effective pixels 410,000 pixels 758 (H) X 540(V)
H.Resolution 690HTVL effective
Synchronizing
system Internal
Video output 1.0Vp-p Composite 75Ohms
S/N ratio 50dB(AGC OFF, Weight ON)
Min.Illumination 0 Lux
Shutter speed 1/25 sec ~ 1/30,720sec (Global Shutter)
Gamma control Standard γ=0.45
White Balance 2000°K ~ 11,000°K Auto. ATW/ AWB selectable by OSD
Power source 12VDC 210mA / 24VAC ~ 210mA
Lens 2.8 ~ 12mm Varifocal Motorized Lens
IR Spectrum 850nm
Viewable distance Up to 150ft at moonless night
Iris control DC IRIS
MTBF of IR 20,000 hours
Operating temp -10°C ~ 50°C
Humidity 0%RH ~ 90%RH
Measurement(mm) 143(dia) x 118(H)
Weight(Approx.g) 1,500
Function
WDR Low/ Normal /Middle/ High
AGC Low/ Normal /High
BLC On/Off
Fluorescent Off/ CRR/ CRR2
ICR DVR Tool Off/ EDGE/ MAX/ FLEX/ ELITE
RS485 Pelco-D
Flip Off/ Horiz/ Vert/ Both
EL-750
Ø143.0
65.0 53.0
118.0
Ø106.5
3-Ø4.5
Ø96.0
120°
120°

16 17
10. OSD Manual for functions control
OSD Menu Tree
ICREALTIME
WDR CONTROL LOW NORMAL MIDDLE HIGH
BLC OFF ON
AGC LOW NORMAL HIGH
WHITE BALANCE ATW AWB..
FLUORESCENT OFF CRR CRR2
ICR DVR TOOL OFF EDGE SERIES MAX SERIES FLEX SERIES ELITE SERIES
RS-485 CAMERA #
PROTOCOL
BAUD RATE
RETURN
FLIP OFF BOTH VERT HORIZ
SAVE&EXIT DEFAULT CANCEL
Setting up the menu
Press the Tact SW to enter <MAIN MENU>
Move the arrow to a specific menu
by pushing the Tact SW up or down.
Adjust the selected feature by pushing the
Tact SW left or right
When completed, move the arrow indicator to SAVE&EXIT and press the TACT SW to
finish all settings.
How to use OSD button (Tact SW)
Press
to enter the menu
to save settings
Push up or down
to select functions
Push left or right
to adjust a level or mode of sub-menu
ICREALTIME
>WDR CONTROL <MEDIUM>
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
FLIP OFF
SAVE&EXIT DEFAULT CANCEL
MAIN MENU
SUB MENU
PRESS
RIGHT
DOWN
LEFT
UP
•
•
•
•
•
•
•
1. WDR(Wide Dynamic Range) CONTROL
Light level is controllable with provided easy-to-use
OSD menu that enables the camera to be ideally set
up for the most of different levels of backlit or contrast
lighting situations.
LOW :
Dynamic range level similar to that of CCD
cameras.
NORMAL:
Suitable for most indoor scenes without
windows or difficult lighting
MIDDLE:
Suitable for normal outdoor scenes and indoor
scenes that include windows.
HIGH :
Maximum setting for harsh outdoor scenes
2.BLC(Back Light Compensation)
OFF :
Highlights in image are prioritized.
ON :
Shadows in image are prioritized.
3.AGC (Auto Gain Control)
LOW :
Low gain limit.
NORMAL:
Normal gain limit.
HIGH :
High gain limit.
4. White Balance
The Automatic White Balance provides an extensive
range color temperature control that covers form
2,000˚Kto 11,000˚Kgenerating natural color image
without being red or blue in varying light conditions.
ATW:
Auto-tracking white balance mode.
AWB :
Set white balance now and lock it
ICREALTIME
>WDR CONTROL <MEDIUM>
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
FLIP OFF
SAVE&EXIT DEFAULT CANCEL
ICREALTIME
WDR CONTROL MEDIUM
>BLC <OFF>
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
FLIP OFF
SAVE&EXIT DEFAULT CANCEL
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
>AGC <NORMAL>
WHITE BALANCE ATW
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
FLIP OFF
SAVE&EXIT DEFAULT CANCEL
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
AGC NORMAL
>WHITE BALANCE <ATW>
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
FLIP OFF
SAVE&EXIT DEFAULT CANCEL

18 19
5. Fluorescent
Color Rolling Reduction (CRR)
OFF :
Not used CRR.
CRR : This color roll reduction mode will work with
manual and auto-iris lenses. However, using it
with auto-iris lenses typically results in
noticeable levels of noise in shadows or dark
areas in the image.
CRR2
This color roll reduction mode works with
auto-iris lenses ONLY. Noise levels are
reduced in shadows or dark areas in the
image compared to the noise levels present
when using the CRR mode, but, dynamic
range is also reduced further.
6. ICR DVR TOOL
Ideal setting with IC Realtime DVR series.
7. RS-485..
*How to control OSD menu over RS485:
“PRESET” key or “IRIS OPEN” key.
OFF :
Default Setting.
EDGE SERIES :
EDGE series
MAX SERIES :
MAX series
FLEX SERIES :
FLEX series
ELITE SERIES :
ELITE series
CAMERA# :
Available to set up from 1 to 255.
PROTOCOL :
Supports PELCO-D.
BAUD RATE : Select a baud rate.(2400, 4800, 9600,
19200)
RETURN.
Move to MAIN MENU.
1)
Set communication speed on the camera to 9600bps.
2) Accord the ID of the camera with the DVR or PTZ
controller. The factory default ID of the camera is
“CAM1”.
3)
On the DVR or PTZ controller, press 95 then press
4) When the MAIN MENU pops up on the screen, move
the cursor using a joystick to the desired menu to
control. When entering a Sub menu, press “IRIS
OPEN” momentarily.
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
>FLUORESCENT <OFF>
ICR DVR TOOL OFF
RS-485..
FLIP OFF
SAVE&EXIT DEFAULT CANCEL
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT OFF
>ICR DVR TOOL <OFF>
RS-485..
FLIP OFF
SAVE&EXIT DEFAULT CANCEL
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT <OFF>
ICR DVR TOOL <OFF>
>RS-485..
FLIP OFF
SAVE&EXIT DEFAULT CANCEL
RS485 SETUP
>CAMERA # 1<1>255
PROTOCOL PELCO-D
BAUD RATE 9600
RETURN
8. FLIP
Adjustable to OFF, HORIZ, VERT, BOTH.
9. SAVE&EXIT
Saves the current settings and exits the menu.
10. DEFAULT
All the settings will be restored to the factory default.
Note.
RS-485 settings are not initialized.
11. CANCEL
Not saves the current settings and exits the menu.
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
>FLIP <OFF>
SAVE&EXIT DEFAULT CANCEL
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
FLIP OFF
>SAVE&EXIT DEFAULT CANCEL
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
FLIP OFF
SAVE&EXIT >DEFAULT CANCEL
ICREALTIME
WDR CONTROL MEDIUM
BLC OFF
AGC NORMAL
WHITE BALANCE ATW
FLUORESCENT OFF
ICR DVR TOOL OFF
RS-485..
FLIP OFF
SAVE&EXIT DEFAULT >CANCEL