iameco XV1-32 User manual

- 1 -
i
ia am me ec c
o
o
T
TM M
X
XV V1 1- -3 32 2″, ,
4
40 0″, ,
46″
C
CO OM MP PU UT TE ER R
L
LC CD D- -T TF FT T- -T TV V
M
MO ON NI IT TO OR RS S
User’s Manual
includes setup, service and
troubleshooting information
Available in solid wood
Ash, Beech, Sapele

- 2 -
All rights reserved.
Copyright © 2007, iameco™computers.
MicroPro™and the iameco™logo are registered
trademarks of Multimedia Computer Systems Ltd and its related entities.
All other trademarks are the property of their respective owners.
Alterations in respect of construction and design, errors and printing errors reserved.

- 3 -
iameco™overview
Modern computer devices are made up of hundreds of different
components, incorporating a host of toxic chemicals. The dominant toxic
components contain brominated flame retardants, PCBs, and heavy
metals like lead, cadmium and mercury, etc. These are extremely toxic
even in the smallest quantities. These chemicals can accumulate in the
environment and damage our health and the health of our children.
MicroPro™are committed through the iameco™range of environmentally
friendly computers to phasing out these contaminants. We believe that
computer manufacturers must take responsibility for the full
environmental impact of their products to bring the e-waste crisis under
control by designing clean electronics with longer life spans that are safe
and eas to recycle and will not expose workers and the environment to hazardous chemicals.
y
We believe our iameco™range of computers will be the third brand of the future. Standard PCs, Apple Mac
and iameco™for the environmentally friendly computers. We have designed iameco™using techniques from
environmental science, and its entire lifecycle has been examined to minimise ecological burdens. We
have minimised the use of hazardous materials such as lead, mercury, chromium, brominated flame
retardants and plastics. iameco™takes a holistic view of recycling and waste minimization. We apply this
philosophy from the outset, beginning in the design stage by creating compact, ultra-efficient products
that use high recycling-value materials wherever possible.
Fashion and greed for new computers with higher performance demanding more speed is fuelling a
growing consumption of computers. The waste mountain of electronic goods is growing rapidly. In 1997 a
standard computer had a lifespan of 7 years now it is as little as 2 years. iameco™computers believe in a
cleaner greener approach to the whole eco design of computers resulting in a much longer lifespan
averaging between 5 and 7 years. We achieve this through the usage of futuristic updateable,
upgradeable, reusable, recyclable modular design components.
To date we have concentrated on the futuristic design approach to computers. We have pioneered and
integrated the following approaches to waste and energy reduction, e.g.
Reduction of the multitude of plastics used for case parts. The current use of aluminium, wood and
renewable wood casings as reusable materials
Reduction of noise emissions (DB)
Reduction of energy consumption
Reduction in the size of PCs to use less material
Minimisation of hazardous materials
U
se of recyclable packaging
In 1999 the company received support from Enterprise Ireland under the Environmentally Superior
Products (ESP) Programme, which gave it access to external advise on the further greening of the iameco™
design. Since then we have been supported by the “EU LIFE programme” and “CGPP” IRL (Cleaner
Greener Production Program), which has enabled us to bring these products to the market.
The study concluded that the design had many technical and commercially feasible environmental
attributes and compared favourably with the European Eco-label specification for PCs. The iameco™design
is based on extending the operational life of the hardware via an upgradeable chassis with modular
interface port design, using raw materials and assembly techniques to increase the recycling and reuse
options at end of life and increasing energy efficiency. iameco™is unique in reflecting best practise and
state-of-the-art technology with respect to energy efficient and environmentally aware design.
To sum it up:
“i am eco” Are you?
Paul Maher Anne Galligan
Supported by:

- 4 -
Getting started
You have just purchased a high-quality environmentally friendly TFT LCD monitor! Thank you for buying
your new iameco™XV1-32″/40″/46″LCD-TFT-TV monitor. Your purchase has contributed to reducing the
burden on the environment and to the further development of environmentally adapted electronic
products.
Please read this manual thoroughly before operating the monitor and keep your user’s manual in an
accessible place at all the times. Make sure the monitor has not been damaged in transit. Should the
monitor be damaged, please contact your local iameco™dealer. Before you set up your monitor, remove
ny protective film from the outside of it.
a
Package contents
Monitor iameco™XV1-32″/40″/46″
Cables 1 × AC power cable
1 × coaxial cable
Accessories 1 × remote control
2 × AAA battery
2 × wall mounting brackets
4 × plugs and fixing screws A & B (for wall mountings)*
Application CD Installation CD (not available in all locations)
Documentation User guide
* 6 × plugs and fixing screws A & B for iameco XV1-40″/46″
If any items are missing or damaged, contact your iameco™dealer.
Fixing
screws A
Fixing
screws B Plug
AC power cable Coaxial
cable
Remote control Wall mounting
brackets
Note: Please keep the box and packing materials in a safe place for re-use. It can be used when
transporting your LCD-TFT-TV monitor in the future or return the packaging to iameco for recycling and
re-use.
Warning: Your AC cord comes equipped with a three-wire grounding plug. This plug will fit a standard AC
outlet. If you are unable to insert the plug into an outlet because the outlet isn’t grounded, contact a
licensed electrician to replace the outlet with a properly grounded outlet.

- 5 -
Features of iameco 32″, 40″, 46″monitors
HD-Ready
The first thing that most people notice about HDTV is the crystal-clear vision on a wide
screen. iameco HD ready TV, packed with cutting-edge technologies and rich features,
guarantees razor sharp images as vivid as reality itself.
Response Time
The ultra-fast 8-millisecond response time means smooth, crisp fast-action video.
Built In Speakers
Experience awesome sound right from your own monitor. With built in speakers you do not
need to purchase additional equipment.
HDMI
HDMI allows 100% transmission of both visual and audio digital signals, ensuring perfect
image and sound reproduction when connected to PC, STB, DVD, or DTV with both digital
visual and audio signals.
Contrast Ratio
The high contrast ratio shows how precise the gradation from black to white is. It ensures
sharp, realistic images that always look their best that offers crystal clear, vivid picture
quality with its sharper blacks and whites.
S-PVA
The innovative S-PVA (Super Patterned Vertical Alignment) solution allows you to see any
display clearly due to the 180 degrees wide viewing angle.
WideViewAngle
Wherever the TV is located, this sleek big-screen display offers users to see any display
clearly with an evenly focused realistic picture with a wide viewing angle. With the 180°
wide-viewing angle, users will see a clear picture, both horizontally and vertically, from any
angle or any position in the room.
PIP
Enjoy two programs at the same time with split-screen picture-in-picture by choosing
between Picture in Picture (PIP), Picture on Picture (POP) or 9 Windows PIP ( 9Win)
Power Saver
This monitor has a built-in power management system called which saves energy by
switching the monitor into low-power mode. A low-power sleep mode will automatically
activate if there has been no user activity for a certain amount of time that is set by
ENERGY STAR®. The main benefit of energy efficiency is lower power bills.
Wall-Mounting
iameco LCD-TFT TVs are wall-mounting compatible which allows you to save on space by
not needing a cabinet etc to stand the screen onto. With a simple and strong two-piece
design provide the ability to mount your new LCD-TFT TV in minutes.

- 6 -
Certified TCO-99
The TCO-99 certification guarantees the customer an excellent ergonomic and visual
environment.

- 7 -
Specifications of 32″, 40″, 46″monitors
Features/Model XV1-32 XV1-40 XV1-46
Aspect ratio 16:90 16:90 16:90
Resolution 1366x768 1366x768 1366x768
Brightness 500(cd/m2)500(cd/m2)500(cd/m2)
Contrast Ratio 1200:1 1200:1 1200:1
Maximum Rate 100 MHz 100 MHz 100 MHz
Viewing Angle
(U/D/L/R) 90/90/90/90 90/90/90/90 90/90/90/90
Display
Response Time 8 ms 8 ms 8 ms
Analog PC H Frequency Range: 20 - 82 kHz
V Frequency Range: 55 - 90 Hz
Maximum resolution> 1280x1027 60Hz
Maximum pixel rate> 110 MHz
Digital PC
(HDMI Mode) H Frequency Range: 20 - 82 kHz
V Frequency Range: 55 - 75Hz
Maximum resolution>1280x102760Hz
Maximum pixel rate> 165 MHz
DTV mode support> 480i/576i, 720P, 1080i
Supported
Signals
CVBS S-Video
Component
TV
NTSC-M. PAL-BGHI. NTSC-4.43. SECAM. PAL-60.
1080i. 720P 480i/576i. 480P/576P.
All PAL / NTSC / SECAM Systems
TV ANT In (75 ohms coaxial cable)
Digital TV Y/Pb/Pr SD Component Video (576i)
AV1 SCART1 AV In(75ohms 0.1/1.0 Vp-p)CVBS,RGB,RF Out
AV2 SCART2 AV In (75 ohms 0.1/1.0 Vp-p) CVBS, AV Out
S-Video S-Video In
Component Y -Pp DTV RCA In (75 ohms, 0.7Vp-p)
PC Analog DSUB In (Analog) 75 ohms ± 10%. 0.7Vp-p ±5%)
Connections
(Video)
HDMI HDMI in (TDMS)
TV Tuner SIF In
SCART1 SCART1 Stereo Sound In (500mVrms)
SCART2 SCART1 Stereo Sound In (500mVrms)
PC Stereo Audio Line In (500mVrms)
S-Video Component RCA Stereo Audio Line In (500mVrms) - Shared RCA
Audio Out Stereo Audio Line Out (500mVrms)
Connections
(Audio)
Speakers 32" 2PCs * 10W, 40" & 46" 4PCs * 10W
Tuning System PAL / SECAM / NTSC System
Tuning Range 45MHz-889MHz
No of Programs 200 Channels
Sound System BG, DK, I, L, L
MTS Support Mono / Stereo/ NICAM / Bi-lingual
TV
Colour 16.7 million
OSD OSD Type OSD Graphics and text
Power Supply 100-240 V(AC)
Power Consumption < 190.OW < 270.OW < 310.OW
Power Consumption < 5W < 5W < 5W
Power
Power Input 110-240 V 110-240 V 110-240 V
With base 921x550x76 1132x662x110 1260x720x110
Dimension
(mm) Without base 921x550x185 1132x697x190 1260x753x110
Weight Weight 23 kg 26 kg 30 kg
Environmental considerations
Operating Temperature: 10oC~40oC (50oF ~104oF)
Humidity: 10%~80%, non-condensing
Storage Temperature: -20oC~45oC (-4oF~113oF)
Humidity: 5%~95%, non-condensing.

- 8 -
Connecting your iameco™monitor
Follow these steps to set up your monitor.
Step 1: Plug the AC power cable into the power adapter and the other end
into a 3-pin socket.
Step 2: Connect the signal cable to the 15-pin, D-Type sub connector on
the back of the monitor and to the VGA port in the computer.
(If you are using an Apple computer, connect the cable to a DVI
connector, and set the pins on your adapter (Adapter not included). PC-
compatible computers do not need an adapter.)
Step 3: Press the Power button to turn on the monitor and turn on your
computer. When your monitor displays an image, the installation is
complete.
Note: To set up the monitor, please ensure that the power of the monitor,
computer system, and other attached devices are turned off before
proceeding with the above steps. Also please read the safety information
(discussed on page 27) before you plug your monitor into a wall socket.
Power ON/OFF Mains
switch power cable
Scart 1 Scart 2
For better display
1. Connect the power cable for the monitor to the power port on the back of the monitor; Plug the power
cable for the monitor into a nearby power socket.
2. Adjust computer resolution and screen injection rate (refresh rate) in the control panel of the
computer as described below to enjoy the best quality of picture. You can have an uneven quality of
picture in the screen if the best quality of picture is not provided in TFT-LCD.
Resolution: 1024 × 768 and Vertical frequency (refresh rate): 60 Hz
3. TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999%
above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE colour seem to be
bright sometimes or some black pixels can be seen. This is not bad quality pixels and can be used
without difficulty. For example, the number of TFT LCD pixels that is contained in the 15" is
2,359,296.
When you clean the monitor and the panel outside, please apply the recommended small amount of
cleaner by using a soft and dry cloth. The LCD area should not be forced or scrubbed harshly. If excessive
force is applied, you can damage the screen and surround.
iameco™32”, 40” , 46” monitor control buttons
Front control buttons
1. Source/Exit button:Choose the input source or exit the
OSD menu.
2. Volume button:Decrease and increase the audio
volume or navigate the OSD menu.
3. Power indicator: When the light is red the monitor is on
standby mode. It glows green during normal operation.
4. On/Off button: Use this button to turn the monitor on
and off.
Control panel from front of monitor
5. IR button: Remote control receiver.
6. CH button: Zap the channels or navigate the On Screen Display (OSD) menu.
7. Select/Menu button: Use this button to Exit the active menu or the OSD.

- 9 -
Rear control buttons
Power On/Off switch:1. Turns on and off mains power.
2. Power connector: Connects the mains power cord of your monitor to the local power supply.
3. DVI connection: Connection for DVI port.
4. VGA connection: Connection for PC port.
5. PC Audio-in: Connection for PC Audio-in.
6. Audio-out: Connection for Audio-out.
7. S-Video: Use this port to connect to media hardware such as DVD players, televisions and
8.
projectors.
Video: Connection for video signal.
9. Audio-in S-video/AV: Connection for audio-in S-video.
10. DTV,DVD connection Video +Audio: Connection for DTV, DVD video+audio
11. Scart 1: Connection for video, DVD, satellite etc.
12. Scart 2: Connection for video, DVD, satellite etc.
13. Antenna input:
Connection for cable TV, sat TV, terrestrial TV etc.
14. RS232: Connection for 9- pin RS232 port.
Note: Never force or over-tighten any connectors. If the connectors or ports don’t join with reasonable
your iameco monitor" on page 7 of the manual for further information regarding cable
ease, they probably don’t match. Make sure that the connectors match the port that you are connecting
and that you have positioned the connector correctly in relation to the ports. Otherwise you may damage
the connections.
See "Connecting
connections or visit the iameco website.
Remote control
Key name Operation
1. Po • Power on/off wer Key
2. Menu Key • Activates main OSD when no main OSD activated
hen no main menu
• Navigates parent menu when main OSD activated
• Stops auto frequency search
• Activates source select OSD w
activated.
3. Enter key • put source that selected by source select
• nction by 0SD help commands when
• en child menu exists.
Changes in
navigation
Executes fu
main OSD activated
Activates child menu wh
4. Up key n no
• source when source OSD activated
• enu when main OSD activated.
• Increases program number & tune channel whe
OSD activated.
Navigates input
• Executes function by OSD help commands when
main OSD activated
Navigates previous m
5. Down key
• source when source OSD activated.
• when main OSD activated.
• Decreases program number & tune channel when no
OSD activated.
Navigates input
• Executes function by OSD help commands when
main OSD activated
Navigates next menu
6. Left Key n no OSD activated.
• Decreases speaker/headphone sound volume whe
• Executes function by OSD help commands when main OSD activated
• Decreases values of user menu when main OSD activated.

- 10 -
Key name Operation
7. Right Key • Increases speaker/headphone sound volume when no OSD activated.
• Executes function by OSD help commands when main OSD activated
• Increases values of user menu when main OSD activated
8. Info • Displays input source information
9. Sleep Time • Displays current sleep timer value by minute when no sleep timer OSD
activated
• Setup minimum sleep timer value more than current sleep timer value when
sleep timer OSD activated.
• If sleep timer is maximum value, disables sleep timer
10. Mute • Toggles speaker/headphone sound mute status
11.Source • Activates source change OSD when source change OSD is not activated
• Deactivates source change OSD when source change OSD is activated
12. PSM • (Picture Standard Mode) Displays picture standard when picture standard OSD
is not activated
13. SSM • (Sound Standard Mode)Displays sound standard when sound standard OSD is
not activated.
• Changes sound standard when sound standard OSD is activated
14. ARC • Displays aspect ratio of image when aspect ratio OSD is not activated
• Changes aspect ratio when aspect ratio OSD is activated
15. STILL • Toggles status between motion and still image
16. PRE CH • Changes to last tuned program.
17. Dual I-II • Displays MTS of sound format when MTS OSD is not activated.
• Changes sound format when MTS OSD is activated
18. Pip • Toggles PIP status
19. Pip Input • Changes PIP input sources when PIP is on
20. Pip Size • Changes PIP image size when PIP is on.
21. Pip Position • Changes PIP position when PIP image size is not double screen.
22. Swap • Swaps main input source and PIP input source
23. S.Select • Selects main / PIP sound source when PIP is on.
24. PC • Changes to PC / DVI source. If current input source is PC, input source is
changed to DVI
25. TV • If current input source is not TV, changes to TV input source
26. 0-9 • Enters digit value to change program directly
27. TTX ON • if main input source is TV that includes TTX information, enters TTX display
mode
28. TTX MIX • If TTX mode on, toggles TTX mix and TTX full display mode
29. TTX: RED CYAN
YELLOW
• Sends TTX Red / Green / Cyan/ Yellow command
30. TTX Hold • Holds current TTX page.
31. TTX Reveal • Reveals concealed information
32. TTX List/Flof • Toggles LIST and FLOF mode
33. TTX Store • Stores ROW24 page to non-volatile memory in LIST mode
34. TTX Update • Updates pages
35. TTX Time • Displays time/date information
36. DTV Setup • No function for this LCD
37. GUIDE • No function for this LCD
38. TV/RADIO • No function for this LCD
39. FAV • No function for this LCD
41. PG UpDown • No function for this LCD
42. PIP CH UpDown • Increases/Decreases channel if pip video is TV or Digital TV
Battery: The remote requires 2 AAA batteries. While inserting batteries make sure to match the plus (+)
ends with the plus markings on the battery case. Dispose of used batteries according to the
manufacturer's instructions.

- 11 -
Mounting your iameco
• Drill the holes. (Refer to the distance between the holes according to the model.)
• Install the plug, part A and the screws.
• Install the parts A.
• Install the screws A on the rear of the LCD-TV.
• Hang the LCD-TV on the installed part A. The screws on the rear would fit in the holes X on part A.
• After fitting the screws to the holes let the LCD-TV slide down to the limits on Parts A.
• Check that it is steady.
It is strongly recommended that you connect all the connection cables before hanging the LCD-TV on the wall.
799 mm
Part A Plugs 182 mm
Fixing
screws B
Hole X
Fixing
screws A
Distance between holes
Model Holes Description
XV1-32 4 holes 799 mm horizontally and 182 mm between the two holes from top to bottom
XV1-40 6 holes 1021 mm horizontally and 50 mm between the first and second holes from top
and 100 mm between the second and the third holes from top
XV1-46 6 holes 1143 mm horizontally and 50 mm between the first and second holes from top
and 100 mm between the second and the third holes from top
Do not fix the TV with other fixations than those provided or suggested by the manufacturer.
Basic operation
• Use AC 110-240 V 50-60 Hz power outlet for the power supply.
• If the screen of the TV is not on, please press the power button on the remote control or on the TV.
• If you want to turn off the TV temporarily, please press the power button on the remote control or on
the TV.
• If you want to turn off the TV completely, please switch of the power ON/OFF switch.
• In TV/AV state, the TV will enter idle state if there is no signal input within 15 minutes.
• In PC state, the TV will enter idle state if there is no signal input within 2 minutes.
• The setting and tuning of picture and sound will be saved when the TV is shut off, which will be working
in the pre-shut off state when the TV is turn on again.
• If PC signal source is used, please first set the resolution of the PC display card as the following modes
(1024×768 60 Hz, 800×600 60 Hz, 640×480 60 Hz)
• If there is line-by-line output of the signal used by the user, signal source with line-by-line output is
recommended.

- 12 -
Preset Timing Modes
This iameco™monitor can support any video mode at the input within the following constraints:
The signal sample frequency on the input 80MHz, the horizontal sync frequency between 30KHz and 60KHz
The modes are detected when presented to the input and previous alignments for set up are automatically
recalled. A true multi-sync monitor emulation is implemented. The factory preset supported modes
nclude:
i
Mode Resolution Refresh rate H-freq Pixel freq Remarks
VGA 640×350 70Hz 31.47KHz 25.175MHz VESA Standard
VGA 720×400 59.940Hz 31.469KHz 25.175MHz IBM VGA 3H
VGA 640×480 60Hz 31.5KHz 25.175MHz Industry Standard
VGA 640×480 72Hz 37.9KHz 31.500MHz VESA Standard
VGA 640×480 75Hz 37.5KHz 31.SOOMHz VESA Standard
SVGA 800×600 60Hz 37.9KHz 40.000MHz VESA Guidelines
SVGA 800×600 72Hz 48.1KHz 50.000MHz VESA Standard
SVGA 800×600 75Hz 46.9KHz 49.500MHz VESA Standard
XGA 1024×768 60Hz 48.4KHz 65.000MHz VESA Guidelines
XGA 1024×768 70Hz 56.5KHz 75.000MHz VESA Standard
XGA 1024×768 75Hz 60KHz 78.750MHz VESA Standard
SXGA 1280×1024 60Hz 64KHz 108.000MHz VESA Standard
SXGA 1280×1024 75Hz 80KHz 135.000MHz VESA Standard
Viewing distance range
Suggested viewing distances for HDTV-capable TVs. The ideal distance depends on several factors,
ncluding signal quality.
i
Screen size Viewing distance range
30" 3.75-6.25 feet
34" 4.25-7 feet
42" 5.25-8.75 feet
50" 6.25-10.5 feet
56" 7-11.75 feet
62" 7.75-13 feet
70" 8.75-14.75 feet
Signal Connector Pin Assignment
AC-DC Adapter
Input AC 100-240V ~2.0 - 1.0A 50/60Hz
Output DC 12V 4A
Note: Use only the iameco™provided AC adapter approved for use with this monitor. Use of another AC
adapter may damage your monitor and invalidate your warranty.
15pin VGA Connector
Pin Signal(D-Sub) Pin
Signal(D-Sub)
1 Red Video 9 N.C.
2 Green Video 10 Sync. Ground
3 Blue Video 11 Ground
4 Ground 12 SDA (DDC Data)
5 Ground 13 H. Sync.
6 Red Ground 14 V. Sync.
7 Green Ground 15 SCL (DDC Clock)
8 Blue Ground
Note: No.5 Pin must be grounded on the PC side.

- 13 -
DVI-I Connector (Digital/Analog)
Pin Signal(DVI-I) Pin
Signal(DVI-I)
1 TMDS Data2- 16 Hot Plug Detect
2 TMDS Data2+ 17 TMDS Data0-
3 TM DS Data2/4 Shield 18 TMDS Data0+
4 TMDS Data4- 19 TMDS Data0/5 Shield
5 TMDS Data4+ 20 TMDS Data5-
6 DDC Clock 21 TMDS Data5+
7 DDC Data 22 TMDS Clock Shield
8 Analogue Vertical Sync. 23 TMDS Clock+
9 TMDS Data1- 24 TMDS Clock-
10 TMDS Data1+ C1 Analogue Red
11 TMDS Data1/3 Shield C2 Analogue Green
12 TMDS Data3- C3 Analogue Blue
13 TMDS Data3+ C4 Analogue H. Sync.
14 +5V Power C5 Analogue Ground
15 Ground (return for +5V, H. Sync. and V. Sync.)
Power Saver
This monitor has a built-in power management system called Power Saver which saves energy by
switching the monitor into low-power mode when it has not been used for a certain amount of time. The
monitor automatically returns to normal operation when you move the computer’s mouse or press a key
on the keyboard.
For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for
long periods (at back of monitor). The power saver system operates with a VESA DPMS compliant video
card installed in your computer. Use software utility installed on your computer to set up this feature.
There are two ways to reduce a product’s energy consumption: by using components that require less
power or by using power management software to modulate the energy consumption of these
components. iameco™employs both techniques to maximize energy efficiency.
We believe efficiency should be the norm. Our computer monitors ship with power management enabled,
meaning that a low-power sleep mode will automatically activate if there has been no user activity for 10
minutes. Another benefit of energy efficiency is lower power bills.
*
Typically 17”, 19” monitors
State Normal
Operation Power Saving Mode EPA/ENERGY 2000 Power Switch Off Unplug
Power Indicator Green Orange, Blinking No Light No Light
Power Consumption ~30W 1W 1W 0W
Power Supply 100-240 V(AC) XV1-32 XV1-40 XV1-46
Power Consumption < 190.OW < 270.OW <310.OW
Power Consumption < 5W < 5W < 5W
Power Input 110-240 V 110-240 V 110-240 V
Plug and Play capability
This monitor can be installed on any plug and play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases, monitor
installation will proceed automatically, unless the user wishes to select alternate settings.
Note: See Power Saver described above for further information regarding power-saving functions. For
energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long
periods. Always use your PC in S3 mode, which is set up in BIOS. All iameco™XPCs are factory set to S3
mode to conserve energy. Do not display a still picture for a long period, as this could cause a residual
image (afterburn).

- 14 -
On Screen Display (OSD) control adjustment for the monitor
Turning LCD-TFT-TV On And Off
Press Power button on the remote control. The PDP/LCD will turn on
and you will be ready to use its features. You can also use the Power
key on the front panel
Select Source
Press Source button on the remote control. Then you can see the source
list menu shown to the right. Press CH+/CH- button on the remote
control to select the source
Volume Control
Press VOL+/VOL- button on the remote control to adjust the volume
level. Press MUTE button on the remote control when you need to cut
the sound temporarily
OSD Menu Structure
OSD (On Screen Display) allows users to control or adjust various
features and settings in accordance with his/her preferences. Press the
MENU/ENTER button on the remote control to see the main OSD menu.
Example of OSD menu
Main Menu: Press the MENU/ENTER button on the remote control to enter the main OSD menu. First,
select Main menu item you need with CH+ & CH- button. To select a main menu items, just press
VOL+ or MENU/VIDEO button on the Remote Control.
Sub Menu: Each menu item has its own sub menu items to set.
Sub Menu items:
A: If there is no part, the item has an under menu. You can enter the under menu and adjust an
item you need.
Select sub-menu item with CH+/CH- button on the remote control and press VOL+ or MENU/ENTER
button to enter the submenu.
B: If there is a part, you can set the item by selecting 
Picture mode
1.Press MENU/ENTER button to display the main OSD menu.
2.Select the picture main menu.
3.Press MENU/ENTER to enter the sub menu.
4.Select Custom and press MENU/ENTER button to enter the sub menu.
Then the custom sub mode appears.
5.You will see the picture setting bars. Just Press BACK button on the
remote control. You can adjust each values of the custom setting,
but the changed values are stored as in Custom mode.
6.Press Exit button to return

- 15 -
Custom
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the picture main menu.
3. Press MENU/ENTER to enter the sub menu.
4. Select Custom and press MENU/ENTER button to enter the sub
menu. Then the custom sub mode appears.
5. You will see the picture setting bars. Just Press BACK button on
the remote control. You can adjust each values of the custom
setting, but the changed values are stored as in Custom mode.
Press +/ - button on the remote control to adjust the brightness level.
Colour Tone
Your LCD-TFT-TV has 5 screen temperatures (colour settings).
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the picture main menu.
3. Press MENU/ENTER to enter the sub menu.
4. Select Colour Tone and press MENU/ENTER button to enter the
sub menu. Then the picture popup window appears.
5. Select the Colour Tone with CH+/CH- button and press
MENU/ENTER button.
6. Press Exit button to return.
WARM 1:2> Screen seems warm: Strong Red.
Normal> Normal: Factory default.
Cool 1:2> Screen seems cool: Strong Blue
Size
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the picture main menu.
3. Press MENU/ENTER to enter the sub menu.
4. Select Size and press MENU/ENTER button to enter the sub
menu. Then the picture popup window appears.
5. Select the Size with CH+/CH- button and press MENU/ENTER
button.
6. Press Exit button to return
Analog TV channel
Country (If in Ireland , choose Ireland)
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu.
3. Press MENU/ENTER to enter the sub menu.
4. Select Country and press MENU/ENTER button to enter the
submenu. Then the picture popup window appears.
5. Select the Size with CH+/CH- button and press MENU/ENTER
button.
6. Press Exit button to return.

- 16 -
Auto Store
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
Press MENU/ENTER to enter the sub menu.
3. Select Auto Store with VOL+/VOL- button and press
MENU/ENTER button.
4. Then you can see the tuning bar. LCD-TFT-TV will execute auto program searching.
5. While searching channel after selecting Start button with VOL+/VOL-, you can also stop channel
searching if you select Stop button
Manual Store
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Manual Store and Press MENU/ENTER to enter the sub
menu.
Manual Store > Prog
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Select the Manual Store menu with CH+/CH- button on the
remote control.
4. Select the Prog. menu with CH+/CH- button on the remote
control.
5. Press MENU/ENTER to enter the sub menu.
6. You will see the picture setting square. You can select the Prog
using CH+/CH- button.
Manual Store > Colour System
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Select the Manual Store menu with CH+/CH- button on the
remote control.
4. Select the Colour System menu with CH+/CH- button on the
remote control. Then the picture popup window appears.
5. You can select the Colour System using CH+/CH- button.
Note: Select PAL for Ireland, England; SECAM for France; NTSC for America
Manual Store > Sound System
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Select the Manual Store menu with CH+/CH- button on the
remote control.
4. Select the Sound System menu with CH+/CH- button on the
remote control. Then the picture popup window appears.
5. You can select the Sound System using CH+/CH- button.

- 17 -
Manual Store > Channel
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Select the Manual Store menu with CH+/CH- button on the
remote control.
4. Select the Channel menu with CH+/CH- button on the remote
control.
5. Press MENU/ENTER to enter the sub menu.
6. You can operate the Channel.
Manual Store > Search
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Select the Manual Store menu with CH+/CH- button on the
remote control.
4. Select the Search menu with CH+/CH- button on the remote
control.
5. Press MENU/ENTER to enter the sub menu.
6. You can operate the Search.
Manual Store > Store
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Select the Manual Store menu with CH+/CH- button on the
remote control.
4. Select the Store menu with CH+/CH- button on the remote
control.
5. Press MENU/ENTER to enter the sub menu.
6. You will see the pictures composed with two squares. You
can select Yes / No with VOL+ or VOL- button
ANALOG TV CHANNEL > Add/Delete
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Select the Add/Delete menu with CH+/CH- button on the
remote control.
4. Press MENU/ENTER to enter the sub menu. Then you can
see the favorite program list.
5. You can select a program with CH+/CH- button on the
remote control.
ANALOG TV CHANNEL > Sort
(Notice: You can't see the sort program list on this picture since this picture isn't a real operating mode but
a design mode.)
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Channel main menu with CH+/CH- button on the
remote control.
3. Select the Sort menu with CH+/CH- button on the remote
control.
4. Press MENU/ENTER to enter the sub menu. Then you can
see the sort program list.
5. You can select a program with CH+/CH- button on the
remote control

- 18 -
To sort the program in the list
If you want to sort a program, press MENU/ENTER button. Then you can select a field with VOL+/VOL-
button. Press MENU/ENTER button on the field to sort. Adjust the field with CH+/CH- button. To return,
press BACK button
ANALOG TV CHANNEL > Manual Store > Name
Press MENU/ENTER button to display the main OSD menu.
1. Select the Channel main menu with CH+/CH- button on
the remote control.
2. Select the Name menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu. Then you can
see the sort program list.
4. You can change a program Name if you want to change
the name of the program.
To change the program name in the list
If you want to change a program Name, press MENU/ENTER button. Then you can select a field with
VOL+/VOL- button. Press MENUIENTER button on the field to sort. Adjust the field with CH+/CH- button.
To return, press BACK button
ANALOG TV CHANNEL > Manual Store > Fine Tune
The Fine Tuning function lets you manually adjust the LCD-TFT-TV's tuner if you are difficult tuning analog
Channels
1. Press MENU/ENTER button to display the main OSD
menu.
2. Select the Channel main menu with CH+/CH- button on
the remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Fine Tune with CH+/CH- button and press
MENU/ENTER button. Then you can see the adjust bar.
5. Adjust the fine tune with VOL+ or VOL- button.
ANALOG TV SOUND > Mode
Your LCD-TFT-TV has four automatic sound settings ("Standard",
"Music", "Movie", "Speech") that are preset at the factory. You can
active Standard, Movie, Music or News by pressing "SSM" button
on the remote control (or by making a selection from the menu)
or you can select "Custom" which automatically recalls your
personalized sound settings.
s
MENU/ENTER button to display the main OSD menu.
c
t the Sound main menu with CH+/CH- button on the remote
r
ol.
s
MENU/ENTER to enter the sub menu.
c
t Volume and press MENU/ENTER button to enter the sub menu.
n
the picture popup window appears.
c
t the Mode with CH+ or CH- button and press MENU/ENTER
o
n.

- 19 -
ANALOG TV SOUND > Volume
1. Press MENU/ENTER button to display the
main OSD menu.
2. Select the Sound main menu with CH+/CH-
button on the remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Volume and press MENU/ENTER button
to enter the sub menu. Then you can see the
Volume bar.
5. Adjust the Volume with VOL+ or VOL- button.
Then press MENU/ENTER button.
ANALOG TV SOUND > Balance
This control allows you to adjust the balance of the left and right speakers output.
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Sound main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Balance and press MENU/ENTER button to enter the sub
menu. Then you can see the Balance bar.
5. Adjust the Balance with VOL+ or VOL- button. Then press
MENU/ENTER button.
ANALOG TV SOUND > Equalizer
You can use the OSD menu to change the Treble, Bass and Balance according to your preference.
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Sound main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Equalizer and press MENU/ENTER button to enter
the sub menu. Then you will see the Equalizer menu bars.
5. Select a gain bar with VOL+, VOL- button on the remote
control and adjust it with CH+/CH- button.
6. Press EXIT button on the remote control to exit equalizer.
The result will be saved automatically.
ANALOG TV SOUND > Auto Volume
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Sound main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Auto Volume and press MENU/ENTER button to enter
the sub menu. Then you will see the popup menu.
5. You can select Yes/No with CH+ or CH- button and press
MENU/ENTER button.

- 20 -
ANALOG TV SOUND > Sound Mode
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Sound main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Sound mode and press MENU/ENTER button to enter
the sub menu. Then you will see the popup menu.
5. Select the Sound Mode with CH+/CH- button and press
MENU/ENTER button.
SETUP > Reset
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Setup main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Reset and press MENU/ENTER button to enter the sub
menu.
5. If you want to reset your TV, press MENU/ENTER button. Then
the system will reset
SETUP > Clock
Set the current time:
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the Setup main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Select Time and press MENU/ENTER button to enter the sub
menu. Then you will see the time menu.
5. Select Clock by pressing VOL+ button.
6. Move the cursor by pressing VOL-, VOL+ button and adjust
time by CH+ and CH- button.
SETUP > On Timer
This LCD-TFT-TV can be set to turn on automatically at specific
time that you chose. Before using timer, you must set the LCD-
TFT-TV's Time as described previously.
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the TIME main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Move the cursor by pressing VOL-, VOL+ button and adjust on
time by CH+ and CH- button.
SETUP > Off Timer
This LCD-TFT-TV can be set to turn off automatically at specific time that you chose. Before using timer,
you must set the LCD-TFT-TV's Time as described previously.
1. Press MENU/ENTER button to display the main OSD menu.
2. Select the TIME main menu with CH+/CH- button on the
remote control.
3. Press MENU/ENTER to enter the sub menu.
4. Move the cursor by pressing VOL-, VOL+ button and adjust off
time by CH+ and CH- button.
(Notice: You can't see the real time on this picture since this
picture isn't a real operating mode but a design mode. In a real
mode, you can see the real clock time.)