iBeam TE-DVR360 User manual

iBEAM Vehicle Safety Systems®iBEAMUSA.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 4/16/19 INSTTE-DVR360
TE-
DVR360
INSTALLATION INSTRUCTIONS
Attention! When testing the aftermarket
equipment, ensure that all factory equipment
is connected before cycling the key to
ignition.
TOOLS REQUIRED
• Cutting/stripping tool • Tape
• Pry tool
TABLE OF CONTENTS
Wiring................................................................... ...2
Operation................... .............................................3
Settings Menu.......... ............................................... 4
Other Menu options................................................5
Power Off Options...................................................6
Specifications..........................................................7
Universal 360 degree Dashcam and
rearview camera
Visit iBeamUSA.com for more detailed information about the product and up-to-date vehicle
specific applications
KIT COMPONENTS
• A) Dashcam with monitor • B) Power harness and extension • C) Rearview Camera A
C
Product Features
•360 view of the front facing, drivers view and
interior of vehicle with audio recording
•Rearview camera included
•4" screen
•Parking Monitor
•Collision lock supported
AB

1.800.221.0932
|
iBEAMUSA.com
2
Dashcam Wiring:
WIRING
(Figure A)
1. Mount the dash camera to the windshield
using the provided double sided tape.
It is suggested to clean the windshield first
with an alcohol wipe.
2. Run the wire and plug in the DC plug to obtain
power to the dash camera.
3. Position the 360 degree camera.
4. Run the extension wire to the rear of the
vehicle for the rearview camera.
5. Mount the rearview camera outside near the
center of the vehicle. It is suggested the
camera be mounted outside. The camera will
be recording the rear visual, but also works as
a backup camera.
6. Connect the RED wire on the extension cable
to a reverse trigger in the vehicle. This will
trigger the reverse input on the dash camera
and the rear visual will go full screen and
provide guidelines. When it is triggered, the
LEDs activate.
RED - Reverse Trigger
18 ft
12 ft
20 in

3
Operation call outs: ( Figure B )
OPERATION
(Figure B)
1. MINI USB POWER: 12 foot DC power cable for the dash
camera power. It can be hooked up to 12v accessory or 12v
constant depending on how the vehicles DC or cigarette
sockets are powered.
2. Rear Camera Connection: The extension cable from the rear
view camera plugs into this slot.
3. Micro SD card slot: Max. 32gb micro SD card
(Figure C)
1 2 3
: Starts the video recording
: Takes a snapshot of the screen
: Playback menu for video and snapshots
: Settings Menu
: Viewing menu
Menu Layover: ( Figure C)
When any of the actions below are needed, tap
the touchscreen and the Menu will appear.

1.800.221.0932
|
iBEAMUSA.com
4
SETTINGS MENUS
(Figure D)
(Figure E)
Settings Menus:
To enter the settings menus, recording
must be stopped by pressing the
icon. Press the setting button to
enter the settings menus.
Settings Video: (Figure C)
In this menu the user can:
•set duration of the loop recording
•set the sensitivity of the G-sensor
•set the frequency(quality) of the recording - this will save storage space on
the micro SD card. (not pictured)
•set if the dash camera should boot up automatically
•set audio recording
•set reversal of the rear camera image
•Turn screen saver on/off
Settings interface: (Figure E)
In this menu the user can:
•set language
•set the brightness (not pictured)
•set the volume
•set the date and time
•format the SD card or perform a system reset

5
OTHER MENU OPTIONS
(Figure F)
(Figure G)
icon in the
Playback Menu: (Figure F)
You can access this menu by hitting the
Menu Layover. (pg. 3 Figured D)
•Provides video files from the 360 camera
•Provides video files from the rearview camera
•Provides snapshots taken
icon in the Menu
Viewing Menu: (Figured G)
You can access this menu by hitting the
Layover. (pg. 3 Figured D)

1.800.221.0932
|
iBEAMUSA.com
6
POWER OFF OPTIONS
Power Off Options: (Figure H)
When the vehicle is turned off, the dashcam screen will display an
alert. This alert will appear for about 3 seconds. If there is no
operation, the unit will be turned off automatically. (Figure H)
There are three options in the alert menu.
•Power off : This option powers down the dashcam.
•Parking Mode : Video will start to record with a shock of
the dashcam and record for 11 seconds and lock the files
so they cannot be overwritten.
•Cancel : Cancels the power down and allows the
dashcam to run on stored powered.
(Figure H)

7
SPECIFICATIONS
REV. 4/16/2019 INSTTE-DVR360

iBEAM Vehicle Safety Systems®iBEAMUSA.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 4/16/19 INSTTE-DVR360
TE-
DVR360
INSTALL ATION INSTRUCTIONS
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
[email protected]