iBell Tools MS06-16 User manual

2
1. GENERAL POWER TOOL SAFETY WARNINGS ____________3
2. SCREWDRIVER SAFETY WARNINGS _____________________6
3. PRODUCT OVERVIEW ___________________________________8
4. PRODUCT SPECIFICATIONS _____________________________9
5. SETUP __________________________________________________10
6. PRODUCT FUNCTIONS _________________________________13
7. GENERAL OPERATION _________________________________16
8. TROUBLESHOOTING ___________________________________18
TABLE OF CONTENTS
IBL MS06-16

3
Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
Power tool plugs must match the outlet. Never modify the plug
in any way. Do not use any adapted plugs with earthed(grounded)
power tools. Modified plugs and un-matching outlets will increase
the risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep it away from heat, oil, sharp edges
or moving parts.
When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury. Save all warnings and
instructions for future reference. The term “power tool” in the
warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool
WORK AREA SAFETY
ELECTRICAL SAFETY
IBL MS06-16

4
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs or alcohol. A moment of
inattention while operating power tools may result in serious
personal injury.
Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes,
hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-
position before connecting to power source and/or battery pack,
picking up or carrying the tool.
Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected
situations.
Dress properly, say no to loose clothing or jewellery. Keep your
hair, clothing away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and
properly used. Use of dust collection can reduce dust-related
hazards.
Have your power tool serviced by a qualified repair-person
using only identical replacement parts.This will ensure that the
safety of the power tool is maintained.
When servicing a power tool, use only identical replacement
parts. Follow instructions in the maintenance section of this
manual. Use of unauthorized parts or failure to follow maintenance
instructions may create a risk of shock or injury.
PERSONAL SAFETY
IBL MS06-16
SERVICE

5
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer
at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users.
Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control.
Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed. Use of the power tool
for operations different from those intended could result in a
hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil
and grease. Slippery handles and grasping surfaces do not allow
for safe handling and control of the tool in unexpected situations.
Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of injury
and fire.
Battery of the tools should be recharged only with the charger
specified by the manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when used with
another battery pack.
POWER TOOL USE AND CARE
IBL MS06-16

6
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact hidden
wiring. Fastener contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the operator an
electric shock.
This appliance can also be used by inexperienced persons and
children aged from 10 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the
hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
The charger and the cordless screwdriver supplied with it are
specifically designed to work together. Only use the charger with
the cordless screwdriver.
Charge the product indoors only as the charger is designed for
indoor use only. Do not charge non-rechargeable batteries.
Protect the charger against moisture and wet conditions. There
is a danger of electric shock.
Charge/operate and store the product in an ambient
temperature of 15-25°C to ensure the longest battery life and best
performance. Do not charge/operate or store the battery in
temperatures below 5°C and above 40°C.
Never attempt to open the product housing for any reason. If
the plastic housing of the product breaks open or cracks,
immediately discontinue its use and do not recharge it.
Do not pierce the product with nails, strike the battery with a
hammer, step on the product or otherwise subject it to strong
impacts or shocks.
Protect the product against heat. Do not place the product in
direct sunlight or use or store the product inside cars in hot
weather. Doing so may cause the battery to generate heat, explode
or ignite.
SCREWDRIVER SAFETY WARNINGS
IBL MS06-16

7
Even if you are operating this product in accordance with all the
safety requirements, potential risks of injury and damage remain.
The following dangers can arise:
Health defects resulting from vibration emission if the product is
being used over long periods of time or not adequately managed
and properly maintained.
Danger of injury and property damage caused by other objects or
due to natural reactions or calamities.
On the product or on the packing box, the rating label and within
these instructions you will find among others the following symbols
and abbreviations. Familiarize yourself with them to reduce hazards
like personal injuries and damage to property.
RESIDUAL RISKS
SYMBOLS
Caution / Warning
Wear protective
gloves
This product is of protection class II. That means it is
equipped with enhanced or double insulation.
Wear hearing and eye protection
Approx. 1.5 hr charging
time
Indoor use only
IBL MS06-16

8
PRODUCT OVERVIEW
1. Tool socket with lock sleeve
2. ON/OFF trigger switch
3. Forward/Reverse rotation control
4. Handle
5. Work light
6. Unlock button
7. Indicator lights
8. Flash light
9. ON/OFF slide-switch for Flash light
10. Charging socket
11. Torque setting
12. Charger
13. Charger jack
IBL MS06-16
2

9
SCREWDRIVER
Rated voltage
Rated no load speed
Tool socket
Torque
Weight
BUILT-IN BATTERY
Type
Capacity
Voltage
CHARGER
Model no
Rated input voltage
Rated input power
Rated output voltage
Rated output current
Protection class
Charging time
Weight
PRODUCT SPECIFICATIONS
: 3.6V
: 200 rpm
: Hex 6.35 mm
: 15+1 Settings
: 0.44 Kg
: Li-Ion
: 1500 mAh
: 3.6V
: TPA-595100VU
: 100-240V~50-60Hz
: 3.6V
: 5V
: 1000 mAh
: Class II
: approx. 1.5 hr
: 0.08 Kg
IBL MS06-16

10
Unpack all parts and lay them on flat, stable surface. Remove all
packing materials.
Make sure the delivery contents are complete and free of any
damage. If you find that parts are missing or show damage, do
not use the product but contact your dealer. Using an incomplete
or damaged product represents a hazard to people and property.
Ensure that you have all the accessories and tools needed for
assembly and operation. This also includes suitable personal
protective equipment.
This product is intended for light fastening and removing screws
with 25 mm or 50 mm driver bits.
The product is not suitable for heavy duty screw driving work
into hard wood or with large diameter screws.
It must not be used for drilling and should not be used for
working on materials that are dangerous to health. For safety
reasons it is essential to read the entire instruction manual before
first operation and to observe all the instructions.
SETUP
UNPACKING AND ENSURING
WARNING! The product must be fully assembled before
operation! Do not use a product that is only partly assembled or
assembled with damaged parts! Follow the assembly instructions
step-by-step and use the pictures provided as a visual guide to easily
assemble the product! Do not connect the product to power supply
before it is completely assembled!
INTENDED USE
IBL MS06-16

11
The battery of this product is integrated in the handle and cannot
be removed. Charge it fully before first use.
The product cannot be operated while charging. Charge in a safe
location away from moisture or heat sources.
The indicator lights show the battery status as below:
RED
LED
YELLOW
LED
GREEN
LED
BATTERY
STATUS
ON
ON
ON
Fully
charged
ON
ON
OFF
Less than
70% charge
ON
OFF
OFF
Less than
45%
charge,i.e,
to be
recharged
CHARGING
As shown in the figure, plug the
charger jack (13) into the charging
socket (10) on the handle (4). Connect
the charger (12) to the power supply.
The indicator light (7) shows the
charging status.
RED - charging
GREEN - charging finished
After charging finished (this normally
takes about 1.5 hour), disconnect the
charger from the power supply and
then pull the charger jack from the
charger socket.
IBL MS06-16

12
Different driver bits can be used with this product depending on the
screw heads being worked with. A suitable number of bits are
available in the tool box. Use only Hex 6.35 mm bits which are 25
mm or 50 mm long.
Lock the power switch by placing the direction and safety switch.
Do not engage the trigger when changing bits.
Insert a suitable driver bit all the way to the stop into the tool
socket (1). Push backward and hold the tool socket lock sleeve (1),
then remove the driver bit from the tool socket.
Use a suitable bit holder to access areas that are hard to reach.
Insert the bit holder into the socket in the same way as the driver
bits, then insert a driver bit into the bit holder.
DRIVER BITS
ON/OFF SWITCH
Switch the product ON by pressing the trigger
switch (2).
Switch the product OFF by releasing the trigger
switch (2)
IBL MS06-16

13
Change the rotational direction from forward to reverse by pressing
the forward /reverse rotation control (3).
1. Move the forward/reverse rotation control switch (3) to the left
(as seen from the operator position) in order to use the product in a
clockwise rotational mode.
2. Move the forward/reverse rotation control switch to the right (as
seen from the operator position) in order to use the product in
anticlockwise rotational mode.
3. Move the rotation control switch to the centre position to lock the
ON/OFF switch and avoid accidental starting.
PRODUCT FUNCTIONS
FORWARD / REVERSE ROTATION CONTROL
Position Application
Rotational
direction
Screw-driving
Screw removing
Lock the ON/OFF switch and
avoid accidental starting
- 1 -
- 2-
- 3-
IBL MS06-16

14
This product has two handle positions for optimum performance
in different work location.
The pistol position provides a firm grip for those jobs where more
torque is required. The rod position suits narrow working areas.
To change to rod position, press and hold the unlock button (6)
and rotate the handle (4) clockwise at the same time until it locks
in place.
To change to pistol position, press and hold the unlock button (6)
and rotate the handle (4) anti-clockwise at the same time until it
locks in place.
WARNING! Only change the rotational direction when the product
is switched off and has come to a complete stop! Always ensure that the
forward/reverse rotation control is adjusted to the correct position
depending on the intended operation! Always push the forward/reverse
rotation control as far as it will go! Do not use the product with the
control switch in any other intermediate position!
HANDLE POSITION
Pistol position Rod position
IBL MS06-16

15
The numbers circling the collar are used to indicate the level of
torque. The higher number on the collar, the higher torque and the
larger fastener can be driven. To select any of the numbers, rotate
the collar until the desired number aligns with the arrow head
indicator on the housing.
TORQUE ADJUSTMENT
By rotating the torque adjustment collar (11)
behind the chuck, it is possible to adjust the
output torque to each of the fifteen settings,
with an additional torque setting as well. This
range of torque settings allows better control
when using as it prevents overtightening of the
screws.
FLASH LIGHT
To turn the flash light (8) ON, slide-press the
ON/OFF switch (9) to ON. To turn the flash
light OFF, slide it to OFF position.
9
AUTOMATIC WORK LIGHT
5
The work light (5) will automatically
illuminate by pressing the ON/OFF switch (2).
This helps to focus on the work more
thoroughly and could work on a not much
bright environment as well.
IBL MS06-16

16
Check the product and charger as well as accessories for damage
before each use. Do not use the product if it is damaged or shows
wear. Double check that the accessories and attachments are
properly fixed.
Always hold the product on its handle. Keep the handle dry to
ensure safe support.
Switch the product off immediately if you are disturbed while
working by other people entering the working area. Always let the
product come to complete stop before putting it down.
Do not overwork yourself. Take regular breaks to ensure you can
concentrate on the work and have full control over the product.
Where possible, secure smaller work-pieces to prevent them from
moving during operation.
Pre-drill the holes with a smaller diameter of the screw to be
screwed.
Hold the product perpendicular to the screw to be screwed in or
out. Holding it at an angle may cause slipping or jamming of the
driver bit.
Place the tip of the driver bit directly on the screw first and then
switch the product on.
Only apply as much pressure as necessary to keep the screw in
place and the driver bit in contact with the screw head. Too much
pressure will cause damage to the screw head and driver bit, too
little pressure will cause the driver bit to slide away.
Remove blocked and stuck screws by changing the rotational
direction.
After use, switch the product off and let it cool down. Check,
clean and store the product as described below.
GENERAL OPERATION
SCREW-DRIVING
IBL MS06-16

17
Keep the product clean. Remove debris from it after each use and
before storage.Do not use chemical, alkaline, abrasive or other
aggressive detergents or disinfectants to clean this product as
they might be harmful to its surfaces Regular and proper cleaning
will help ensure safe use and prolong the life of the product.
Clean the product with a dry cloth. Use a brush for areas that are
hard to reach.
Always store the product in a place that is inaccessible to
children. We recommend using the original package for storage
or covering the product with a suitable cloth or enclosure to
protect it against dust.
Before and after each use, check the product and accessories (or
attachments) for wear and damage. If required, exchange them for
new ones as described in this instruction manual. Observe the
technical requirements.
This product does not contain any parts that can be repaired by
the consumer. Contact an authorised service centre or a similarly
qualified person to have it checked and repaired.
CLEANING AND STORAGE
MAINTENANCE AND REPAIR
WARNING! Always switch the product off, disconnect the product
from the power supply and let the product cool down before
performing inspection, maintenance and cleaning work! Only perform
repairs and maintenance work according to these instructions! All
further works must be performed by a qualified specialist!
IBL MS06-16

18
Suspected malfunctions are often due to causes that the users can
fix themselves, therefore check the product using this section. In
most cases the problem can be solved quickly.
Problem
Possible Cause
Solution
1. Product does
not start
1.1 Battery discharged
1.2 Battery damaged
1.3 Other electrical
defect to the product
1.1 Charge battery
1.2 Check by a
specialist electrician
1.3 Check by a
specialist electrician
2. Product does
not reach full
power
2.1 Battery capacity
too low
2.1 Charge battery
3. Unsatisfactory
result
3.1 Driver bit is worn
3.2 Driver bit not
suitable for intended
operation
3.1 Replace with a new
one
3.2 Use suitable driver
bit
TROUBLESHOOTING
WARNING! Only perform the steps described within these
instructions! All further inspection, maintenance and repair work must
be performed by an authorised service centre or a similarly qualified
specialist if you cannot solve the problem yourself!
IBL MS06-16

19
Disposal of an exhausted battery pack. The built-in battery is Li-Ion type. To
preserve natural resources, please recycle or dispose of the battery properly.
Consult your local waste authority for information regarding available
recycling and/ or disposal options. Discharge your battery by operating your
product before disposal. To remove the built-in battery from the product,
separate the handle shells from one another by removing the fixing screws for
handle, disconnect the battery from the circuit with a suitable tool. Fully wrap
it with tape to avoid exposing two conductive ends of the battery.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your Local Authority or local store for recycling advice.