IBM 04K0058 User manual

The following paragraph does not apply to the United Kingdom or any country where such provisions are
inconsistent with local law:
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow disclaimer of express or implied warranties in certain transactions, therefore, this
statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made
to the information herein; these changes will be incorporated in new editions of the publication. IBM may
make improvements and/or changes in the product(s) and/or the program(s) described in this publication at
any time. It is possible that this publication may contain reference to, or information about, IBM products
(machines and programs), programming, or services that are not announced in your country. Such references
or information must not be construed to mean that IBM intends to announce such IBM products, programming,
or services in your country.
Requests for technical information about IBM products should be made to your IBM reseller or IBM marketing
representative.
Thank you for purchasing OPTIONS by IBM. Please take a few moments to register your product and provide
us with information that will help IBM to better serve you in the future. Your feedback is valuable to us in
developing products and services that are important to you, as well as in developing better ways to
communicate with you.
Register your option on the IBM Web site at: http://www.pc.ibm.com/register
IBM will send you information and updates on your registered product unless you indicate on the Web site
questionaire that you do not want to receive further information.
Products Involved:
Option PN FRU PN Description
04K0058 02K3416
02K3418
06H6326
00K8155
10H2924
76H7339
12J4498
Sanyo 32X-14X FRU with Headphone
Hitachi 32X-14X FRU with Headphone
IDE Cable
Audio Cable
Audio Cable
IBM PC Desktop Bezel FRU
IBM PC Tower Bezel FRU
Safety Information:

To avoid a shock hazard, do not connect or disconnect any cables or perform installation, maintenance, or
reconfiguration of this product during an electrical storm.
To avoid shock hazard:
- The power cord must be connected to a properly wired and earthed receptacle.
- Any equipment to which this product will be attached must also be connected to properly wired receptacles.

Pour éviter tout risque de choc électrique, ne manipulez aucun câble et n'effectuez aucune opération
d'installation, d'entretien ou de reconfiguration de ce produit au cours d'un orage.
Pour éviter tout risque de choc électrique:
- Le cordon d'alimentation doit être branché sur une prise d'alimentation correctement câblée et mise à la
terre.
- D'autre part, tout le matériel connecté à ce produit doit également être branché sur des prises d'alimentation
correctement câblées et mises à la terre.

Para evitar peligo de descargas, no contecte o desconecte ningún cable, ni realice ninguna instalación,
mantenimiento o reconfiguración de este producto durante una tormenta eléctrica.
Para evitar peligro de descargas:
- El cale de alimentación debe estar conectado a una toma de alimentación adecuadamente cableada y con
toma de tierra.
- Cualquier equipo al cual se conecte este producto debe estar tamblén conectado a tomas de alimentación
adecuadamente cableadas.
Cuando sea posible, utilice una mano para conectar o desconectar los cables de señal para impedir que se
produzcan posible descargas eléctricas al tocar dos superficies con potencial eléctrico distinto.
DANGER!
Quick Installation Guide:
The IBM 32X-14X Internal IDE CD-ROM Drive can read a compact disc (CD) containing approximately 680
MB of information.
The drive delivers data at up to 32 times the standard CD-ROM speed, delivering data at up to 4800 KB per
second. The CD-ROM drive is designed for installation in a personal computer that uses the integrated drive
electronics (IDE) or the enhanced IDE architecture. The drive may be mounted vertically or horizontally. For
more detailed installation instructions, go to User's Guide.
In addition to this book, the option package includes:
- IBM 32X-14X Internal IDE CD-ROM Drive
- Two audio cables
- Four mounting screws (M3 x 5 mm, slotted)
- IDE cable for connecting two IDE devices
- Two faceplates for use with certain systems
- IBM 32X-14X Internal IDE CD-ROM Drive Option Diskette

- Laser Safety Guide for CD-ROMs
Contact your place of purchase if an item is missing or damaged. Be sure to retain your proof of purchase. It
might be required to receive warranty service. See Help and Service Information for technical support
information.
Installing the Drive:
Opening the Computer:
1. Turn off the computer and all attached peripherals.
2. Unplug the power cords for the computer and all attached devices.
3. Remove the cover from the computer.
Unpacking the Drive:
1. In order to discharge any accumulated static electricity, touch an unpainted metal surface for at least two
seconds.
2. Take the bag the drive is packed in and touch it to an unpainted metal surface for at least two seconds.
3. Remove the drive from the bag.
If you must put the drive down, place the antistatic bag on a flat padded surface, such as a magazine, and
place the drive on the bag with the component side facing up.
Selecting an IDE Port:
Newer computers typically have two IDE ports. If your computer has two IDE ports, use the secondary IDE
port to connect the CD-ROM drive. Typically the secondary IDE port is adjacent to the primary IDE port that
connects to your hard disk drive.
The IDE port you select and the cable position you select will determine which configuration jumper setting
you will use for the drive. See Setting the Configuration Jumper for instructions on setting the configuration
jumper.
If you have two IDE ports, connect the CD-ROM drive to the secondary IDE port with the IDE cable that
comes with your drive. If the CD-ROM drive is the only device on the secondary IDE port, you will use the
master configuration setting. If there is another device on the secondary port in addition to the CD-ROM
drive, you will use the slave configuration setting.
If you must attach the CD-ROM drive to the same IDE port as a faster device, such as a hard disk drive, you
will use the slave setting for the CD-ROM drive and the master setting for the faster device. In some
instances, the hard disk drive may require a master-with-slave-present setting when another device on the
same cable is configured as a slave. For further information on setting configuration jumpers on other
devices, refer to the documentation that came with your system or with the device in
question.
Some non-IBM computers support the cable-select setting, where the position of the device on the cable
determines whether adevice is master or slave. See the documentation that comes with your computer to
determine if your system supports this setting.
Setting the Configuration Jumper:

The illustration above shows the master 1setting, the slave 2setting, and the cable-select 3 setting.
Configure the CD-ROM drive by placing a jumper over one pair of pins. If your CD-ROM drive has three pairs
of pins, refer to the illustration above left to set the jumper. If your drive has five pairs of pins, disregard the
first two pairs, as they are for factory use only.
The jumper setting positions for the last three pairs of pins are shown in the illustration, above right.
If you are configuring the CD-ROM drive as master, set the jumper to the master 1device setting. (This is
how the drive is set when it is shipped.) If there is a second device on the IDE port, check that the device is
configured as slave.
If you are configuring the CD-ROM drive as slave, set the jumper to the slave 2 device setting. Check that the
other device on the IDE port is configured as master (or master-with-slave-present).
If you are configuring the CD-ROM drive as cable-select, set the jumper to the cable-select 3device setting. If
there is another device on the IDE port, check that the device is also configured for cable-select.
Mounting the Drive in the Bay:
Attention: Be sure to use the M3 x 5 mm mounting screws in the option package when you are driving
screws directly into the drive. Using screws that are too long might damage the drive. You can mount the
CD-ROM drive either horizontally or vertically in the computer. If you mount the drive vertically, you must
secure any CDs you place into the drive before the drive tray is closed, or the CD-ROM drive will not be able
to read the CD properly.
1. Slide the drive into the bay. Your system may have specific required procedures for installing storage
devices. Refer to the documentation that came with your system for further instructions.
2. Align the drive-bay screw holes with the threaded holes in the drive housing or mounting bracket. Be sure
to use the M3 x 5mm mounting screws provided with this drive. Using the wrong size screws might damage
the drive.
3. Thread the screws in loosely to check their position. Usually two screws are used on each side. Check to
make sure the alignment is correct, then tighten the screws to secure the drive. Do not overtighten.
Attaching the Cables to the Drive:
1. Connect the cables to the CD-ROM drive as follows:

a. Attach a 40-pin IDE-cable connector 2 to the IDE connector on the drive. Align the cable so that the color-
coded edge is closest to the power cable connector 3. Use the IDE cable provided with this option if there is
no cable attached to the IDE port or if there is only one device connector on the IDE cable.
b. Attach a four-pin power-cable connector 3to the device dc-power connector.
c. If you have a sound adapter, connect one of the audio cable connectors 1to the device audio-out
connector. Use the audio cable that has a connector that fits your sound adapter and save the other cable in
case you use a different sound adapter in the future.
Attaching the Faceplates:
This option package includes two faceplates which conform to the curved design of certain IBM systems. If
your computer system has a curved design, you may attach one of the included faceplates so that the front of
the CD-ROM drive matches the exterior cabinet. Choose the faceplate that best fits your system, and attach it
after you have mounted the CD-ROM drive in the appropriate bay. The bezel will not be used with all IBM
systems.
Completing the Hardware Installation:
1. Be sure that the drive is securely mounted and the connectors are firmly attached.
2. Be sure the cables do not interfere with the computer cover and do not block the power-supply fan blades
or air-flow paths.
3. Reinstall the computer cover.
4. Reconnect all devices and check any devices that might have become disconnected, such as the
keyboard, mouse, and monitor.
5. Plug all power cords into electrical outlets.
Updating Your Computer Configuration:
Because you changed the hardware, the configuration-setup information screen should display when you turn
on your computer. If you don't see this screen, check your computer documentation for information about
accessing the configuration or setup utility program.
To see the configuration information for most IBM computers, press F1 during startup when the graphic
displays in the upper right corner of the screen. When you have finished reviewing the information, save the
changes and exit.
Note: Some older computers with one IDE port might not display the CD-ROM drive information when you
review the configuration-setup information. You still can use the CD-ROM drive in this situation as long as you
have properly completed the installation.
Installing Device Drivers:
This section contains the instructions for installing device drivers for the CD-ROM drive, based on the
operating system you are using. Go to the section which corresponds to your operating system. Note: User
requirements vary; if you are using DOS or OS/2 as your operating system, the device driver settings for those
operating systems can be customized. If your system does not work well with the default settings given in the
installation instructions in this section, please refer to Customizing Device Driver Configuration Settings for
information on how to customize your device driver configuration settings. View the README file on the 32X-
14X Internal IDE CD Rom Drive Option Diskette for additional notes that were not available when this manual

was created. You may view the file on-line if you run CDSETUP from the 32X-14X Internal IDE CD Rom Drive
Option Diskette.
Installing the Device Driver for Windows 95:
In most instances, Microsoft Windows 95 will automatically detect the CD-ROM drive. If the CD-ROM drive is
automatically detected, Windows 95 will then use the device drivers which are included with the operating
system, and you will not need to install the drivers on the Option Diskette. If Windows 95 is in 32-bit mode for
IDE, the CD-ROM drive will be recognized by the operating system. Otherwise, follow the instructions on your
screen to install the device drivers from the Option Diskette.
Installing the Device Drivers for DOS, DOS with Windows 3.X, Windows 95 in MS-DOS mode, or OS/2
Warp version 3.0 or Higher:
1. Go to a command line.
2. Insert the Option Diskette into drive A.
3. Type in A:CDSETUP, then press Enter.
4. Using your mouse or the arrow keys, select Setup.
5. Follow the instructions on your screen to properly install the driver.
6. When setup is complete, select Exit.
7. You will be prompted to restart your system; the changes will not take effect until you do so.
Note: To resolve resource conflicts or if you need options that are not found in the CDSETUP device-driver
installation program, refer to the READ.ME file on the Option Diskette. If you have problems installing the
device driver, refer to the CDSETUP program help information.
Installing the Device Driver for Windows NT 3.51:
1. Start Windows.
2. Click on the Start button and open the Main folder.
3. Click on Control Panel.
4. Double-click on Devices.
5. Click on atapi.
6. Click on Startup.
7. Click on Boot.
8. Click on OK.
9. Click on Cdfs.
10. Click on Startup.
11. Click on System.
12. Click on OK.

13. Click on Close.
14. Close the Control Panel.
15. Shut down and restart the computer.
See the Windows NT installation guide for more information.
Installing the Device Driver for Windows NT 4.0:
Windows NT version 4.0 should automatically detect the presence of the IDE CD-ROM drive. No additional
steps are required to activate the device drivers.
Some IBM Windows NT pre-loads contain a piixide device driver. This device driver replaces the Windows NT
native atapi device driver, and provides DMA support. The IDE CD-ROM will not work if both the atapi and
piixide device drivers are enabled at the same time. If this occurs, go into the Control Panel and set the
Startup parameter of one of the drivers to Disabled.
User's Guide:
Product Description:
The IBM 32X-14X Internal IDE CD-ROM Drive can read a compact disc (CD) containing approximately 680
MB of information. It is designed for installation in a personal computer that uses the integrated drive
electronics (IDE) or the enhanced IDE architecture.
The CD-ROM drive delivers data up to 32 times the standard CD-ROM speed, delivering data at up to 4800
KB per second. The drive reads compact discs meeting the ISO-9660 and High-Sierra Group (HSG)
standards. It also reads multiple-session, extended architecture (XA) discs, such as the Kodak Photo CD.
In addition to this book, the option package includes:
- IBM 32X-14X Internal IDE CD-ROM Drive.
- Two audio cables.
- Four mounting screws (M3 x 5 mm, slotted.)
- Two system faceplates.
- 32X-14X Internal IDE CD-ROM Drive Option Diskette.
- IDE cable for connecting two IDE devices.
- Laser Safety Guide for CD-ROMs.
Contact your place of purchase if an item is missing or damaged. Be sure to retain your proof of purchase. It
might be required to receive warranty service. The Option Diskette includes installation and support
programs, such as:
- Installation programs for DOS, Windows, and OS/2
- IDE CD-ROM device drivers.
- Audio CD-player program for DOS.
- READ.ME file with additional installation information.
- Diagnostic program.
You can find information on how to get help, technical support, and warranty service in Appendix D, Help and
Service Information on page 3-24.

1 - Headphone jack. This jack provides audio output to the headphones.
2 - Volume control. This controls the audio output volume.
3 - Busy indicator. This light comes on when the drive reads a data CD or plays an audio CD.
4 - CD tray. This is where you load and unload a CD.
5 - Manual-eject hole. This provides access to the manual eject mechanism to remove a CD from the drive.
Note: Your CD-ROM drive will have a manual-eject hole in one of the positions in the illustration, but not both.
6 - Eject/Load button. Opens and closes the CD tray.
1 - Reserved.
2 - Audio-out connector. Connects the analog audio signals to a sound adapter.
3 - Configuration pins. Sets the drive configuration.
4 - IDE connector. Connects the CD-ROM drive to the IDE cable.
5 - DC power connector. Connects the dc power cord to the CD-ROM drive.
Before You Begin:
Read the following information before you start your installation. The installer of the drive will have to complete
the following steps:
- Determine which IDE port to use, and the corresponding configuration setting.
- Set the configuration jumper on the drive (and possibly make changes to the configuration settings of other
devices.)
- Physically install the drive in a drive bay.
- Configure the system.
- Install a device driver.
If you do not understand these procedures, or are unsure about your ability to perform all the procedures
described, have a qualified computer technician install the CD-ROM drive for you, or call an IBM technical-
support representative.
Installation Requirements:
Before you begin installing the drive, be sure you have everything you need, such as:
Documentation:
You might need the documentation that comes with your computer, operating system, or IDE bus adapter if it
is separate from the computer.
Minimum Processor: