IBT Technologies IB828 User manual

IB828
AMD Athlon™64 / Athlon™64 x2
(Dual Core) / Sempron™
Embedded Board
USER’S MANUAL
Version 1.0

ii IB828 User’s Manual
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
AMD Athlon™64 / Athlon™64 x2 (dual core) / Sempron™
processors are registered trademarks of AMD Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.

IB828 User’s Manual iii
Table of Contents
Introduction.......................................................1
Product Description.....................................................................1
Checklist ......................................................................................2
IB828 Specifications....................................................................3
Board Dimensions........................................................................4
Installations.......................................................5
Installing the CPU........................................................................6
Installing the Memory..................................................................7
Setting the Jumpers......................................................................8
Connectors on IB828.................................................................12
BIOS Setup.......................................................19
Drivers Installation......................................37
VGA Drivers Installation...........................................................38
Realtek High Definition Codec Audio Driver Installation........41
LAN Drivers Installation ...........................................................43

iv IB828 User’s Manual
This page is intentionally left blank.

INTRODUCTION
IB828 User’s Manual 1
Introduction
Product Description
The IB828 Embedded board incorporates the high performance AMD 780E
embedded PC chipset optimized for AMD Socket AM2 processors with speeds
up to 2.9GHz and with FSB up to 2000MHz. The board has two DDR II
SODIMM sockets to support a maximum memory capacity of 4GB. Particular
attention is given to multiple high-resolution display interfaces including a
HDMI connector at the edge of the board.
IB828 Product Features:
-With AMD 780E / SB710 Chipset
-Supports Socket AM2 CPUs, AMD Athlon™64 / Athlon™64 x2
(dual core) / Sempron™
-Supports up to 2.9GHz, FSB 2000MHz
-HDMI multiple display interface
-PCIe Gigabit LAN (Realtek RTL8111C)
-Dual DDR II SODIMM sockets, up to 4GB
-6x USB, 2x COM, 2x Mini PCIe socket, HDA audio, 1x SATAII
HDD dock

INTRODUCTION
2 IB828 User’s Manual
Checklist
Your IB828 package should include the items listed below.
The IB828 embedded board
This User‟s Manual
1 CD containing chipset drivers and flash memory utility


INTRODUCTION
IB828 User’s Manual 3
IB828 Specifications
CPU Type
AMD Socket AM2+/AM3 ; PGA 940-pins (supporting <=
45W CPUs only)
System Speed
800~1600 MHz (Hyper Transport)
CPU FSB
1.0 ~ 2.6GHz
Cache
512~2048 KB L2 cache
Green /APM
APM1.2
BIOS
Award BIOS: supports ACPI Function
Chipset
North Bridge:M780E
South Bridge: SB710
Memory
2 x 200-pin DDRII SO-DIMM, Dual Channel, Max. capacity
4GB
Video –AMD 780E
(Primary)
AMD M780Ebuilt-in Radeon HD3200 based graphic
engine, supports full DirectX10.0. Dual concurrent displays
(max)
- 2 x HDMI
Video –M96
(Optional)
M96-CSP512 (E4690) GPU
-2 x HDMI
LAN
Realtek RTL8111C PCI-e Gigabit LAN controller x 1
USB
AMD SB710 built-in USB 2.0 host controller, support 6
ports 4 x external ports, 2 x-pin headers
Audio
AMD SB710 built-in audio controller + HDA ALC888 w/ 7.1
channels, (External Front L/R, Rear L/R)
IDE
None
LPC I/O
Winbond W83627EHG 2 x COM & hardware monitor, smart
DC fan control
RTC/CMOS
SB710 built-in with on board Lithium Battery
Edge Connector
4 x single vertical HDMI connector (one joint audio)
4 x USB connectors
2 x RJ45 for 2 COM ports (COM1: RS232, COM2:
RS232/422/485)
1 x RJ-45 GLAN connector
2 x Microjack Audio connectors
1 x DIN4 DC-IN power connector
1 x Power Switch button
1 x Reset button
1 x HDD LED
1 x Power LED
On Board Headers
1 x pin header for 2 x USB ports
1 x header for HDA Audio outputs
2 x mPCIe slot (52-pin PCIe Minicard Slot)
1 x system fan pin header (w/ Smart DC fan control)
1 x CPU fan pin header (w/ Smart DC fan control)
Watchdog Timer
Yes (256 segments, 0, 1, 2…255. sec/min)
Power Connector
Power Mini DIN-4
System Size
200(W) x 250(L) mm x 35(H)
Serial ATA
AMD SB710 built-in SATA II (3.0Gb/sec) host controller,
supports 1 x SATA 2.5 HDD Dock

INTRODUCTION
4 IB828 User’s Manual
[
Board Dimensions
Bottom View

INSTALLATIONS
IB828 User’s Manual 5
Installations
This section provides information on how to use the jumpers and
connectors on the IB828 in order to set up a workable system. The topics
covered are:
Installing the CPU.................................................................................. 6
Installing the Memory............................................................................ 7
Setting the Jumpers................................................................................ 8
Connectors on IB828........................................................................... 12

INSTALLATIONS
6 IB828 User’s Manual
Installing the CPU
The IB828 board supports a Socket AM2 (940-pin) processor socket for
AMD Athlon™64 / Athlon™64 x2 (dual core) / Sempron™processors.
To install the CPU, unlock first the socket bypressing the lever sideways,
then lift it up to a 90-degree angle as shown below. Then, position the
CPU above the socket such that the CPU corner aligns with the gold
triangle matching the socket corner with a small triangle. Carefully insert
the CPU into the socket and push down the lever to secure the CPU.
Then, install the heat sink and fan.
NOTE:
Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.

INSTALLATIONS
IB828 User’s Manual 7
Installing the Memory
The IB828 board supports two DDR2 memory sockets that can support
up to 4GB memory, DDR2 400/533/667 (w/o ECC function).
Installing and Removing Memory Modules
To install the DDR2 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR2 module so that the key of the DDR2 module aligns
with that on the memory slot. Insert the module into the socket at a
slight angle (approximately 30 degrees). Note that the socket and
module are both keyed, which means that the module can be installed
only in one direction.
2. To seat the memory module into the socket, apply firm and even
pressure to each end of the module until you feel it slip down into the
socket.
3. With the module properly seated in the socket, rotate the module
downward. Continue pressing downward until the clips at each end
lock into position.
4. To remove the DDR2 module, press the clips with both hands.

INSTALLATIONS
8 IB828 User’s Manual
Setting the Jumpers
Jumpers are used on IB828 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB828 and their respective functions.
Jumper Locations on IB828...................................................................9
JP2: ATX or AT Power Selection........................................................10
JP4, JP5, JP6: RS232/422/485 (COM2) Selection ..............................10
JB1: Clear CMOS Contents.................................................................11

INSTALLATIONS
IB828 User’s Manual 9
Jumper Locations on IB828
JP2: ATX or AT Power Selection ....................................................... 10
JP4, JP5, JP6: RS232/422/485 (COM2) Selection.............................. 10
JB1: Clear CMOS Contents................................................................. 11

INSTALLATIONS
10 IB828 User’s Manual
JP2: ATX or AT Power Selection
JP2
ATX Power
ATX
AT
JP4, JP5, JP6: RS232/422/485 (COM2) Selection
COM1 is fixed for RS-232 use only. COM2 is selectable for RS232,
RS-422 and RS-485. The following describes the settings for COM2.
COM2
Function
RS-232
RS-422
RS-485
Jumper
Setting
(pin closed)
JP4:
1-2
JP5:
3-5 & 4-6
JP6:
3-5 & 4-6
JP4:
3-4
JP5:
1-3 & 2-4
JP6:
1-3 & 2-4
JP4:
5-6
JP5:
1-3 & 2-4
JP6:
1-3 & 2-4
Pin #
Signal Name
RS-232
R2-422
RS-485
1
RTS
RTS+
NC
2
DTR
RX-
NC
3
TXD
RX+
NC
4
GND
GND
GND
5
DCD
TX-
DATA-
6
RXD
TX+
DATA+
7
DSR
RTS-
NC
CN1,
CN2

INSTALLATIONS
IB828 User’s Manual 11
JB1: Clear CMOS Contents
JB1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS

INSTALLATIONS
12 IB828 User’s Manual
Connectors on IB828
Connector Locations on IB828 ............................................................13
CN9: DC Power Jack (+12V only) ......................................................14
CN1, CN2: Console port......................................................................14
U32: Gigabit LAN RJ45 Port...............................................................14
CN7, CN8: Audio Line In and Line Out..............................................14
CN3, CN4, CN5, CN6: USB1/2/3/4 Ports...........................................14
SW1: Power Button .............................................................................14
LED1: Power LED and HDD LED......................................................14
J1, J2: AMD 780E HDMI Connector ..................................................15
J3, J4: ATI E4690 HDMI Connector...................................................15
J15: USB6/USB7 Connector................................................................15
J5: Audio Pin Header for Chassis Front Panel.....................................16
J6: DDR II DIMM Socket CHA ..........................................................16
J7: DDR II DIMM Socket CHB ..........................................................16
J8, J9: Mini PCI-E X1 Socket..............................................................16
J13: Digital I/O Connector (4 in, 4 out) ...............................................17
CPU_FAN1: DC-CPU Fan Power Connector.....................................17
SYS_FAN1: DC-system Fan Power Connector..................................17

INSTALLATIONS
IB828 User’s Manual 13
Connector Locations on IB828
Connector Locations on IB828
CN9: DC Power Jack (+12V only)...................................................... 14
CN1, CN2: Console port...................................................................... 14
U32: Gigabit LAN RJ45 Port .............................................................. 14
CN7, CN8: Audio Line In and Line Out.............................................. 14
CN3, CN4, CN5, CN6: USB1/2/3/4 Ports........................................... 14
SW1: Power Button............................................................................. 14
LED1: Power LED and HDD LED ..................................................... 14
J1, J2: AMD 780E HDMI Connector.................................................. 15
J3, J4: ATI E4690 HDMI Connector................................................... 15
J15: USB6/USB7 Connector ............................................................... 15
J5: Audio Pin Header for Chassis Front Panel..................................... 16
J6: DDR II DIMM Socket CHA.......................................................... 16
J7: DDR II DIMM Socket CHB .......................................................... 16
J8, J9: Mini PCI-E X1 Socket.............................................................. 16
J13: Digital I/O Connector (4 in, 4 out)............................................... 17
CPU_FAN1: DC-CPU Fan Power Connector .................................... 17
SYS_FAN1: DC-system Fan Power Connector.................................. 17

INSTALLATIONS
14 IB828 User’s Manual
CN9: DC Power Jack (+12V only)
Pin #
Signal Name
1
+12V
2
+12V
3
GND
4
GND
5
GND
CN1, CN2: Console port
The console port is an RJ45 RS-232 serial port.
Pin #
Signal Name
1
RTS
2
DTR
3
TXD
4
GND
5
DCD
6
RXD
7
DSR
8
CTS
U32: Gigabit LAN RJ45 Port
CN7, CN8: Audio Line In and Line Out
CN3, CN4, CN5, CN6: USB1/2/3/4 Ports
SW1: Power Button
LED1: Power LED and HDD LED
The green LED at the bottom is power LED. The red LED on top is the
HDD LED.

INSTALLATIONS
IB828 User’s Manual 15
J1, J2: AMD 780E HDMI Connector
[
Signal Name
Pin #
Pin #
Signal Name
DATA 2-
1
2
GND
DATA 2+
3
4
DATA 1+
GND
5
6
DATA 1-
DATA 0+
7
8
GND
DATA 0-
9
10
CLOCK +
GND
11
12
CLOCK -
NC
13
14
NC
DDC CLOCK
15
16
DDC DATA
GND
17
18
+5V
HOT POWER
19
20
N.C.
J3, J4: ATI E4690 HDMI Connector
Signal Name
Pin #
Pin #
Signal Name
DATA 2-
1
2
GND
DATA 2+
3
4
DATA 1+
GND
5
6
DATA 1-
DATA 0+
7
8
GND
DATA 0-
9
10
CLOCK +
GND
11
12
CLOCK -
NC
13
14
NC
DDC CLOCK
15
16
DDC DATA
GND
17
18
+5V
HOT POWER
19
20
N.C.
J15: USB6/USB7 Connector
Signal Name
Pin
Pin
Signal Name
Vcc
1
5
Ground
D0-
2
6
D1+
D0+
3
7
D1-
Ground
4
8
Vcc

INSTALLATIONS
16 IB828 User’s Manual
SATA1: SATA HDD Dock
The SATA HDD dock combines a SATA power connector and a SATA
interface connector.
Signal Name
Pin #
Pin #
Signal Name
GND
S1
P1
V3.3
A+
S2
P2
V3.3
A-
S3
P3
V3.3
GND
S4
P4
GND
B+
S5
P5
GND
B-
S6
P6
GND
GND
S7
P7
GND
P8
V5
P9
V5
P10
V5
P11
Reserve
P12
GND
J5: Audio Pin Header for Chassis Front Panel
Signal Name
Pin
Pin
Signal Name
S_SURR_L
1
2
S_SURR_R
S_SURR_JD
3
4
GND
R_SURR_L
5
6
R_SURR_R
R_SURR_JD
7
8
GND
MIC1
9
10
MIC2
MIC_JD
11
12
GND
CEN
13
14
LFE
CEN_JD
15
16
Ground
J6: DDR II DIMM Socket CHA
J7: DDR II DIMM Socket CHB
J8, J9: Mini PCI-E X1 Socket