IBT Technologies IB770 User manual

IB770
Transmeta Crusoe TM5400/5600
Half Size PCI CPU Card
with Audio/LAN/VGA
USER’S MANUAL
Version 1.0

ii IB770 User’s Manual
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 are trademarks of International Business Machines
Corporation.
Crusoe and LongRun are registered trademarks of Transmeta
Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.

IB770 User’s Manual iii
Table of Contents
Introduction...............................................................1
Product Description..........................................................1
Checklist...........................................................................2
Specifications....................................................................3
Board Dimensions.............................................................4
Installations ..............................................................5
Installing the Memory (SODIMM) ....................................6
AT OR ATX Power Installation........................................7
Jumpers on IB770.............................................................8
Connectors on IB770 ......................................................13
Watchdog Timer Configuration.......................................26
BIOS Setup..............................................................27
BIOS Introduction..........................................................28
BIOS Setup.....................................................................28
Standard CMOS Setup....................................................30
BIOS Features Setup.......................................................33
Integrated Peripherals .....................................................36
Power Management Setup...............................................38
PNP/PCI Configuration...................................................40
PC Health Status .............................................................41
Load Fail-Safe Defaults...................................................42
Load Optimized Defaults.................................................42
Supervisor / User Password............................................42
Save & Exit Setup...........................................................42
Exit Without Saving........................................................42
LAN Drivers Installation.........................................43
Audio Drivers Installation......................................49
Appendix.................................................................53
A. Post Codes.................................................................53
B. Interrupt Request Lines (IRQ)....................................53

iv IB770 User’s Manual
This page is intentionally left blank.

INTRODUCTION
IB770 User’s Manual 1
Introduction
Product Description
The IB770 little board is a high-performance multimedia Little Board
based on the Transmeta Crusoe TM5400/5600 processor. The Crusoe
processor a revolutionary x86-compatible solution that features:
•Remarkably low power consumption, allowing the processor to run
cooler than conventional chips.
•High performance, optimized for real-life usage patterns. Crusoe
delivers, whether you're browsing the web, watching a DVD, or
recalculating your spreadsheet.
•Full x86 compatibility, so you are free to run the applications and
Internet plugins of your choice.
The IB770 packs all the functions of a versatile system, including audio,
SM721 VGA, Intel 82559 Single chip Ethernet . System memory is
provided by 64/128/256MB on board and one SODIMM socket that
accommodates up to 256MB SDRAM. (Total maximum size=512M)
The Award BIOS facilitates easy system configuration and peripheral
setup. Other advanced features include DiskOnChip flash disk support,
watchdog timer, PC/104, USB, IrDA interface.
DiskOnChip flash disks are storage devices that have no moving parts
and emulates FDD/HDD with Flash/RAM/ROM offering reliable
data/program storage and long life span. They are reliable and suitable for
industrial or other harsh environments characterized by motion, shock,
vibration, adverse temperature, dust and humidity. Other features include
faster data access, longer MTBF, lower power consumption, cost
effective for small capacity and small form factor.
PC/104 is an ISA interface that supports compact-form-factor PC/104
modules (3.6” x 3.8”). It supports self-stacking and pin-and-socket
connector. PC/104 features a standard form factor for Embedded
applications. It is reliable, small in size and has low power consumption.
Flexible mechanical configurations can be attained with PC/104.
Modules support various functions such as display, audio, digital I/O,
GPS, PCMCIA, fax/modem, Ethernet, SCSI, RS-232/422/485 and SSD.

INTRODUCTION
2IB770 User’s Manual
Checklist
Your IB770 package should include the items listed below. Damaged or
missing items should be reported to your supplier.
•The IB770 Transmeta Crusoe Half Size PCI CPU Card
•This User’s Manual
•One compact disc containing the following:
•SMI VGA Driver and Flash ROM Utility
•Intel 82559 Ethernet Drivers
•VIA 686A, AC97 Audio Drivers
•1 x FDD Ribbon Cable
•1 x IDE Ribbon Cables
•2 x Serial Port Ribbon Cable and 1 Parallel Port Attached to a
Mounting Bracket
•1 x Y-Cable supporting a PS/2 Keyboard and a PS/2 Mouse
•1 x 3-pin power cable
•Optional cables such as:
•2 x USB Cable
•1 x Audio Cable (for IBD 771 Audio daughter card with
Line_in, Line_Out, Mic Jacks)

INTRODUCTION
IB770 User’s Manual 3
Specifications
Processor
Supported Transmeta Crusoe Processor
TM5400 / TM5600, 533MHz ~ 600MHz
66MHz Front Side Bus
Chipset VIA VT82C686A chipset
BIOS Award BIOS
Supports ACPI, DMI, PnP
System Memory 1x SODIMM socket support up to 256MB capacity, 3.3V
Multi I/O Chipset VIA VT82C686A chipset
I/O Features 1x FDD (up to 2.88MB, 3 Mode)
1x Parallel Port (EPP, ECP Port)
2x Serial Ports:(1xRS232, 1xRS232/422/485 )
Bus Master IDE 40 Pin IDE Connector 2.54mm (Primary) x1
44 Pin IDE Connector 2.00mm (Secondary) x1
On-board VGA SMI SM721G4/G8 (4MB/8MB embedded memory)
CRT VGA connector x 1
Supports LVDS connector for DSTN panels
On-board Audio VIA VT82C686A AC97 Digital Audio Controller
Optional Audio daughter card (IBD771)
With Line In, Line Out, Mic Jacks
On-board
Ethernet Intel 82559 single chip Ethernet controller
10/100Mbps data transfer speeds
RJ45 LAN connector x1
DiskOnChip Supports M-
Systems 2MB~144MB DiskOnChip flash disk
Digital I/O 4 In 4 Out (2x6 pin hHeader)
Hardware
Monitoring VIA VT82C686A
Monitors CPU/system temperature and voltages
USB Support USB x4 device for ( 2x4 pin header) x2
Watchdog Timer 32 levels
Expansion slot PC/104 expansion connector
IrDA IrDA headers for wireless communication (1x5 pin header)
Other Features AT/ATX power supply select
External ATX power connector (5vsb)
Form Factor Half Size CPU card
Dimensions 185x122mm (7.2”x4.8”)

INTRODUCTION
4IB770 User’s Manual
Board Dimensions

INSTALLATIONS
IB770 User’s Manual 5
Installations
This section provides information on how to use the jumpers and
connectors on the IB770 in order to set up a workable system. The topics
covered are:
Installing the Memory (SODIMM) ....................................6
AT / ATX Power Select ....................................................7
Jumpers on IB770.............................................................8
Connectors on IB770 ......................................................13
Watchdog Timer Configuration.......................................26

INSTALLATIONS
6IB770 User’s Manual
Installing the Memory (SODIMM)
The IB770 has a 144-pin SODIMM socket. The SODIMM socket
supports a maximum total memory of 256MB in SDRAM single side
type. The memory capacities supported are 64MB, 128MB and 256MB.
Installing and Removing DIMMs
To install the SODIMM , locate the memory slot on the little board and
perform the following steps:
1.Hold the SODIMM so that the two keys of the DIMM align with those
on the memory slot.
2.Gently push the SODIMM in an upright position until the clips of the
slot close to hold the DIMM in place when the SODIMM touches the
bottom of the slot.
3.To remove the SODIMM, press the clips with both hands.
Top View of SODIMM Socket
Note: Do not add or replace the memory chips installed on the board
without consulting the manufacturer.

INSTALLATIONS
IB770 User’s Manual 7
AT / ATX Power Select
JP16: AT/ATX Power Supply Select
JP16Setting Function
Pin 1-2
Short/Closed AT Power Supply
Pin 2-3
Short/Closed ATX Power Supply
Notes:
1.When using AT power supply, set the ACPI Function in the Power
Management Setup of the BIOS to Disabled.
2. When using ATX power supply, set the ACPI Function in the
Power Management Setup of the BIOS to Enabled.

INSTALLATIONS
8IB770 User’s Manual
Jumpers on IB770
Jumpers are used on the IB770 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB770 and their respective functions.
Jumper Locations on IB770................................................................ 9
JP3: Clear CMOS Content................................................................10
JP4: DiskOnChip Address Select......................................................10
JP5, JP6, JP7: RS232/RS422/RS485 (COM2) Selection..............10
JP8: COM1/2 RS232 +5V / +12V Power Setting..........................11
JP9: On Board LAN Select ...............................................................11
JP16: AT/ATX Power Supply Select................................................11
JP17: LVDS Panel Power Select......................................................11
SW1: Panel/Resolution Switch Setting............................................12

INSTALLATIONS
IB770 User’s Manual 9
Jumper Locations on IB770
JP3: Clear CMOS Content
JP4: DiskOnChip Address Select
JP5, JP6, JP7: RS232/RS422/RS485 (COM2) Selection
JP8: COM1/2 RS232 +5V / +12V Power Setting
JP9: On Board LAN Select
JP16: AT/ATX Power Supply Select
JP17: LVDS Panel Power Select
SW1: Panel /Resolution Switch Setting

INSTALLATIONS
10 IB770 User’s Manual
JP3: Clear CMOS Content
JP3 Setting Function
Pin 1-2
Short/Closed Normal Operation
Pin 2-3
Short/Closed Clear CMOS Content
JP4: DiskOnChip Address Select
JP4 Setting Address
Pin 1-2
Short/Closed DC000-DDFFF
Pin 2-3
Short/Closed DE000-DFFFF
JP5, JP6, JP7: RS232/RS422/RS485 (COM2) Selection
JP5 JP6, JP7 Pin Short Function
JP5: 1-2
JP6: 3-5, 4-6
JP7: 3-5, 4-6RS232
JP5: 3-4
JP6: 1-3, 2-4
JP7: 1-3, 2-4RS422
JP5: 5-6
JP6: 1-3, 2-4
JP7: 1-3, 2-4RS485

INSTALLATIONS
IB770 User’s Manual 11
JP8: COM1/2 RS232 +5V / +12V Power Setting
JP8 Pin # Signal Name JP8 Signal Name JP5 Pin #
1+5V +5V 2
3NRIA NRIB 4
5+12V
+12V 6
COM1 Settings: Pin 1-3 short = +5V, Pin 3-5 short = +12V
COM2 Settings: Pin 2-4 short = +5V, Pin 4-6 short = +12V
JP9: On Board LAN Select
JP9 Setting Function
Pin 1-2
Short/Closed LAN Enable
Pin 2-3
Short/Closed
LAN Disable
JP16: AT/ATX Power Supply Select
JP16 Setting Function
Pin 1-2
Short/Closed AT Power Supply
Pin 2-3
Short/Closed ATX Power Supply
JP17: LVDS Panel Power Select
JP17 Setting Function
Pin 1-2
Short/Closed
5V
Pin 2-3
Short/Closed
3.3V

INSTALLATIONS
12 IB770 User’s Manual
SW1: Panel/Resolution Switch Setting
Panel ID SW
1-1SW 1-2SW 1-3SW 1-4Panel Type
0ON ON ON ON 640x480 TFT
1OFF ON ON ON 640x480 DSTN
2ON OFF ON ON 800x600 TFT
3OFF OFF ON ON 800x600 DSTN
4ON ON OFF ON 1024x768TFT
5OFF ON OFF ON 1024x768 DSTN
6ON OFF OFF ON Reserved
7OFF OFF OFF ON Reserved
8ON ON ON OFF Reserved
9OFF ON ON OFF Reserved
10 ON OFF ON OFF Reserved
11 OFF OFF ON OFF Reserved
12 ON ON OFF OFF Reserved
13 OF ON OFF OFF Reserved
14 ON OFF OFF OFF Reserved
lPanel ID 2 supports 800X600 TFT x18 bitt.
lPanel ID 4 supports 1024x768 TFT 18 bit.
lPanel ID10 Supports 1024x768 TFT x 24 Bit
lPanel ID12 Supports 800x600 TFT x 24 Bit

INSTALLATIONS
IB770 User’s Manual 13
Connectors on IB770
The connectors on IB770 allows you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The following
table lists the connectors on IB770 and their respective functions.
Connector Locations on IB770.........................................................14
CNO1: Audio Connector for Line_In,Line_Out,Mic. Jack.............15
J3: Digital I/O Connector (4 in, 4 out).............................................16
J4: Floppy Drive Connector..............................................................16
J5: IrDA Connector ...........................................................................17
J6: Primary IDE Connector 40 Pin (2.54mm).................................17
J7: Secondary IDE Connector 44Pin (2.00mm)..............................18
J8, J9: COM1, COM2 Serial port.....................................................18
J10: Parallel Port Connector.............................................................19
J11: PS/2 Keyboard and Mouse Connector .....................................20
J12: CD-In Audio Connector............................................................20
J13: System Function Connector......................................................20
J14: CPU Fan Power Connector ......................................................21
J15: RJ45 LAN Connector................................................................22
J16: External ATX Power Connector...............................................22
J18: VGA CRT Connector................................................................22
J19: 24-Bit LVDS Connector (DF13-20)........................................23
J21, J22: USB Connectors................................................................24
CON1A, CON1B: PC-104 Connector.............................................25

INSTALLATIONS
14 IB770 User’s Manual
Connector Locations on IB770
J3: Digital I/O Connector (4 in, 4 out)
J4: Floppy Drive Connector
J5: IrDA Connector
J6: Primary IDE Connector 40Pin(2.54mm)
J7: Secondary IDE Connector 44Pin(2.00mm)
J8,J9: COM1,COM2 Serial port
J10: Parallel port Connector
J11: PS/2 Keyboard and Mouse Connector
J12: CD-In Audio Connector
J13: System Function Connector
J14: CPU Fan Power Connector
J15: RJ45 LAN Connector
J16: External ATX Power Connector
J18: VGA CRT Connector
J19: 24-Bit LVDS Connector (DF13-20)
J21: USB 0,USB1 Connector
J22: USB2,USB3 Connector
CON1A,CON1B: PC-104 Connector
CNO1: Audio Connector for Line_In,Line_Out,Mic. Jack

INSTALLATIONS
IB770 User’s Manual 15
CNO1: Audio Connector for Line_In,Line_Out,Mic. Jack
Signal Name Pin Pin Signal Name
NC 12Mic
Line_In_L 34Line_In_R
Line_Out_L 56Line_Out_R
Gnd 78Ground

INSTALLATIONS
16 IB770 User’s Manual
J3: Digital I/O Connector (4 in, 4 out)
This 12-pin Digital I/O connector supports TTL levels and is used to
control external devices requiring ON/OFF circuitry.
Signal Name
Pin # Pin # Signal Name
IN0 17+5V
IN1 28OUT0
IN2 39Ground
IN3 410 OUT1
GROUND 511 +12V
OUT2 612 OUT3
J4: Floppy Drive Connector
J4 of the IB770 is a 34-pin header and will support up to 2.88MB FDD.
Signal Name Pin # Pin # Signal Name
Ground 12RM/LC
Ground 34No connect
Ground 56No connect
Ground 78Index
Ground 910 Motor enable 0
Ground 11 12 Drive select 1
Ground 13 14 Drive select 0
Ground 15 16 Motor enable 1
Ground 17 18 Direction
Ground 19 20 Step
Ground 21 22 Write data
Ground 23 24 Write gate
Ground 25 26 Track 00
Ground 27 28 Write protect
Ground 29 30 Read data
Ground 31 32 Side 1 select
Ground 33 34 Diskette change