ICC ICCMSLRCRP User manual

•To mount ladder rack runway to the wall
• Includes 1 bracket and 2 J-Bolts
• Wall fasteners are not included
• Hole size for mounting to the wall is 0.35"
Note: Drywall can not support the weight of ladder rack
• Includes 1 triangle and 2 J-Bolts
• Wall fasteners are not included
• Hole size for mounting to the wall is 0.35"
Note: It is recommended to install a triangle every 5'
How to Mount Ladder
Wall Support Bracket, Perpendicular
Part No.: ICCMSLAWSK
Wall Support Triangle, Parallel
Part No.: ICCMSLTWSK
Wall Support Bracket, Vertical
Part No.: ICCMSLVWBK
• To secure ladder rack runway flat against the wall
• Includes 2 brackets
• Wall fasteners not included
• Hole size for mounting to the wall is 0.43"
5' Ladder Rack Kit, Perpendicular
Part No.: ICCMSLRW05
• To route cable from rack to wall
• Includes a 5’ ladder rack, a relay bracket, a wall bracket,
2 J-bolts and 2 end caps
• Hole size for mounting to the wall is 0.35"
J-Bolt
Wall Support Bracket
Wall Bracket
Wall Bracket
J-Bolt
Triangle
Wall Support Bracket
Rack
Relay Rack Bracket
J-Bolt
888-ASK-4ICC [e-mail] icc.com
© Copyright 2017, ICC. ICC and ICC logo are registered trade name and trademark. All rights reserved.
INSTALLATION INSTRUCTIONS
Ladder Rack System
IMPORTANT: Before you start, please plan on how the ladder rack system is to be configured.
MSR-0352-RevD

• To sustain over-hanging ladder rack runway to the ceiling
• Includes 2 threaded rods (6'), 2 ladder brackets, 2 ceiling
brackets, and 8 nuts
• Ceiling fasteners not included
• Hole size for mounting to the ceiling is 0.53"
• Max load: 132lbs/ft when supported every 5'
How to Mount Ladder
Ceiling Mount Kit with 6' Rods
Part No.: ICCMSLCMRK
4 Post Relay Rack Brackets
Part No.: ICCMSL4PBK
• To secure ladder rack runway over 4 post racks
• Includes 2 parallel mounting brackets, 2 perpendicular
mounting brackets and 2 J-Bolts
• To maintain proper cable bend radius at drop points
• Includes 2 radius controlled drops and 4 screws
Cable Radius Drop
Part No.: ICCMSLRRDB
• To join ladder rack runway at ends
• Includes 2 feet and 2 Butt splice kits
• Floor fasteners not included
• Hole size for mounting to the floor is 0.55"
Floor Mount Kit
Part No.: ICCMSLMFFK
Bracket
Rack
4-Post Adjustable Distribution Rack
Part #:
ICCMSR4P84 7' H, 45 RMS
Adjustable
Rod
Ceiling bracket
Ladder bracket
Butt splice
Feet
Radius drop
888-ASK-4ICC [e-mail] icc.com
© Copyright 2017, ICC. ICC and ICC logo are registered trade name and trademark. All rights reserved.
INSTALLATION INSTRUCTIONS
Ladder Rack System
IMPORTANT: Before you start, please plan on how the ladder rack system is to be con$gured.
MSR-0352-RevD

Option 1: Mount bracket parallel to rack as shown using 2 J-Bolts.
Then mount ladder running parallel to rack as shown using 2 J-Bolts.
Option 2: Mount bracket perpendicular to rack as shown using 2
J-Bolts. Then mount ladder running perpendicular to rack as
shown using 2 J-Bolts.
On Cable Managment Racks
Option 2: Place ladder on top and bracket underneath
perpendicular to rack as shown. Secure both of them using
2 J-Bolts.
Option 1: Mount bracket parallel to rack as shown using 2 J-Bolts.
Then mount ladder facing parallel to rack as shown using 2 J-Bolts.
Part No. ICCMSLRRBK
Includes: 1 bracket, 4 J-Bolts, and 4 nuts.
Hole positions and size .375"
How to Mount Ladder on a Rack with a Relay Rack Bracket Kit
On Distribution Racks
J-Bolt
Relay Rack Bracket
J-Bolt
Relay Rack Bracket
J-Bolt
Relay Rack Bracket
2-Post Distribution Racks
Part #:
ICCMSR1984 7' H, 45 RMS
ICCMSR1972 6' H, 38 RMS
ICCMSR1948 4' H, 24 RMS
J-Bolt
Relay Rack Bracket 2-Post Cable Management Rack
Part #:
ICCMSCMRH7 7’H, 44 RMS
888-ASK-4ICC [e-mail] icc.com
© Copyright 2017, ICC. ICC and ICC logo are registered trade name and trademark. All rights reserved.
INSTALLATION INSTRUCTIONS
Ladder Rack System
IMPORTANT: Before you start, please plan on how the ladder rack system is to be con!gured.
MSR-0352-RevD

• To join the ends of ladder rack runway together
• Includes 20 brackets, 10 bolts, and 10 washers
• To allow ends to adjust in various angles
• Includes 2 swivel butt slices
• To fasten ladder rack runway in a tee intersection
• Includes 4 brackets, 2 nuts, and 2 bolts
Part No.: ICCMSLTJSKPart No.: ICCMSLRBSK
End to End (Butt) Splice Kit Tee-Junction Splice Kit
Swivel Butt Splice
Part No.: ICCMSLESSK
How to Connect Ladder and Protect Cable
• To cover the ends of ladder rack runway
• Includes 2 end caps
Protective End Caps
Part No.: ICCMSLPECK
• To prevent cable from falling off ladder rack runway
• Includes ten (10) 7'' posts and 10 mounting screws
Part No.: ICCMSLRCRP
Ladder Rack Weight Chart
50% Capacity Cable Runway Fills
Distance
Between Span
Weight
Capacity Width CAT 6A
(50%**)
CAT 6
(50%**)
CAT 5e
(50%**)
10' straight section
Part # ICCMSLST10 300 lb.* 12" 500 720 1100
5' straight section
Part # ICCMSLST05 500 lb.* 12" 500 720 1100
*When properly secured on both ends of ladder rack runway straight sections
**Cable !lls are based on .34 inch outside diameter (OD) CAT 6A, .24 inch O.D. CAT 6, and .21
inch O.D. CAT 5e ICC cable
Cable Retaining Post Kit
End cap
Bolt
Nut
Tee-Junction splice
Cable retainer
Mounting screw
Bolt
Butt splice
900 corner
888-ASK-4ICC [e-mail] icc.com
© Copyright 2017, ICC. ICC and ICC logo are registered trade name and trademark. All rights reserved.
INSTALLATION INSTRUCTIONS
Ladder Rack System
IMPORTANT: Before you start, please plan on how the ladder rack system is to be con!gured.
MSR-0352-RevD