ICOP Technology VSX-6154-V2 User manual

VSX-6154-V2 / VSX-6154-V2-PLUS
DM&P Vortex86SX 300MHz
PC/104 CPU Module
with 4S/2USB/VGA/LCD/ LAN/GPIO
128MB DDR2 Onboard
User’s Manual
(Revision 1.2A)

Copyright
The information in this manual is subject to change without notice for continuous improvement in
the product. All rights are reserved. The manufacturer assumes no responsibility for any
inaccuracies that may be contained in this document. And makes no commitment to update or to
keep current the information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part,
in any form or by any means without the prior written permission of the ICOP Technology Inc..
Copyright 2007 ICOPTechnology Inc.
Manual No. IUM6154-V2000-01 Ver.1.0A September, 2009
Manual No. IUM6154-V2000-01 Ver.1.1A May, 2010
Manual No. IUM6154-V2000-01 Ver.1.2A November, 2010
Trademarks Acknowledgment
Vortex86DXis the registered trademark of ICOP Technology Inc.
Other brand names or product names appearing in this document are the properties
and registered trademarks of their respective owners. All names mentioned herewith
are served for identification purpose only.

T a b l e o f C o n t e n t s
T ab l e o f C o n t e nt s.............................................................iii
C h a p t e r 1 Introduction……………………………………………1
1.1 Packing List............................................................1
1.2 Product Description................................................2
1.3 Specifications.........................................................3
1.4 Board Dimension....................................................5
C h a p t e r 2 Installation……………………………………………..6
2.1 Board Outline.........................................................6
2.2 Connectors & Jumpers Location............................7
2.3 Connectors & Jumpers Summary...........................9
2.4 PinAssignments & Jumper Settings......................11
2.5 System Mapping...................................................21
2.6 Watchdog Timer...................................................24
2.7 GPIO....................................................................25
2.8 SPI flash...............................................................26
C h a p t e r 3 Driver Installation……………………………………27
Appendix ………………………………………………………………..28
A. TFT Flat Panel Data Output......................................28
B. TFTFlat Panel Support List.......................................29
C. LVDS Flat Panel Support List....................................31
D. Flat Panel Wiringand Lighting..................................32
E. TCP/IPlibrary for DOS real mode.............................33
F. BIOS Default Setting..................................................34
Warranty............................................................................................35

Vortex86SX-6154-V2 Vortex86SXPC/104 CPU Module
1
C h a p t e r 1
Introduction
1.1 Packing List
Product Name Package
VSX-6154-V2
&
VSX-6154-V2-PLUS
Embedded Vortex86SX CPU All-in-One Board
Manual & Drivers CD x 1
RS232 cable x 4
PRINTER cable x1
IDE cable x 1
USB cable x 1 (USB port x 2)
VGA cable x 1
LAN cable x 1
GPIO cable x 1
AUDIO Line x2
PS/2 Mouse cable x 1
PS/2 Keyboard cable x 1
Screw Kit x 1

Vortex86SX-6154-V2 Vortex86SXPC/104CPUModule 2
1.2 Product Description
The VSX-6154-V2 family of low-power x86 embedded controller is designed to meet PC/104
specification, and integrated with the following features.
300 MHz Vortex86SX System-On-Chip
VGA, TFT/LVDS LCD support up to
1280x1024 resolution
128 / 256MB DDR2 system memory
Enhanced IDE
10/100Mbps Ethernet
2 USB 2.0 (host)
Up to 4 serial ports
Parallel port
16-bit GPIOs
Onboard
2MB SPI Flash
PC/104-Plus expansion bus
Meet PC/104 stacking spec.
2 watchdog timer
JTAG interface
AMI BIOS
Single voltage +5V DC
Support extended operating
temperature range of -20°C to +70°C
The VSX-6154-V2 PC/104 family of embedded controller is designed with backward compatibility
in mind, to provide migration path for projects facing end-of-life challenges with their existing x86
based PC/104 controller.The VSX-6154-V2 family of controller is designed as a plug in
replacement, with backward compatibility to support legacy software to help extend existing
product life cycle without heavy re-engineering.
VSX-6154-V2 is suitable for broad range of data-acquisition, Industrial automation, Process
control,Automotive controller,AVL, Intelligent Vehicle management devic,Medical device,
Human machine interface, Robotics, machinery controlAnd more…application that required
small footprint, low-power and low-cost hardware with open industry standard such as PC/104.

Vortex86SX-6154-V2 Vortex86SXPC/104CPUModule 3
1.3 Specifications
Features VSX-6154-V2
CPU DM&P SoC CPU Vortex86SX- 300MHz
Real Time Clock with Lithium Battery Backup
Cache L1:16K I-Cache, 16K D-Cache
BIOS AMI BIOS
Bus Interface PC/104 Standard Compliant (Optional: PCI-104)
System Memory 128 / 256MB DDR2 Onboard
Watchdog Timer Software programmable from 30.5 us to 512 seconds x2
sets(Watchdog 1 fully compatible with M6117D)
VGA XGI Volari Z9s Chipset
VGA and TFT Flat Panel Interface Support
LVDS Flat Panel Interface Support (Optional)
Onboard 32MB VGA Memory
Support resolution up to 1280 x 1024,16MB colors
LAN Integrated 10/100M Ethernet
I /O Interface Enhanced IDE port x1
RS-232 port x3
RS-232/422/485 port x1 (RS485: Auto Direction)
Parallel port x1
USB port x2 (USB 2.0 version)
16-bit GPIO port x1
10/100Mbps Ethernet port x1
Connectors
2.00 mm 44-pin box header for IDE x1
2.00 mm 44-pin box header for LCD x 1
2.00 mm 10-pin box header for VGA x1
2.00 mm 10-pin box header for USB x1
2.00 mm 26-pin box header for Print x1
2.00 mm 20-pin box header for 16-bit GPIO x1
2.00 mm 10-pin box header for RS-232 x4
2.00 mm 8-pin header for Ethernet x 1
2.54 mm 5-pin box header for Keyboard x1
2.54 mm 5-pin header for Mouse x1
2.54 mm 4-pin header for DC-in x1
2.54 mm 3-pin header for RS-485 x1
2.54 mm 2-pin header for Reset x1
2.54 mm 7-pin header for Redundancy x1(Opt)
2.54 mm 2-pin header for SYS-Fail-SW- x1(Opt)
1.25 mm 6-pin Wafer for JTAG x1

Vortex86SX-6154-V2 Vortex86SXPC/104CPUModule 4
Flash Disk Support
Onboard 2MB SPI Flash Disk (Driver: A)
44-pin IDE Flash Disk( EmbedDisk 16MB or above)
Power Requirement Single Voltage +5V @ 720mA
Dimension 90 X 96mm (3.54 x 3.77 inches)
Weight 83g
Operating
Temperature -20°C ~ +70°C
-40°C ~ +85°C (Optional)

Vortex86SX-6154-V2 Vortex86SXPC/104CPUModule 5
1.4 Board Dimension

Vortex86SX-6154-V2 Vortex86SXPC/104CPUModule 6
C h a p t e r 2
Installation
2.1 Board Outline
(Note1: COM2 RS232/422/485 is selected by BIOS setting)
(Note2: VI/O Default setting of PCI-104 connector is +5V)
(Note3: PCI-104 connector is optional)
(Note4: VSX-6154-V2-512 is optional)
(Note5: Redundancy Signal and System-Fail-SW are optional)

Vortex86SX-6154-V2 Vortex86SXPC/104CPUModule 7
2.2 Connectors & Jumpers Location
Connectors
(Note1: J7 & J8 Redundancy Signal and System-Fail-SW are optional)