ICP PAC-170 User manual

PAC-170 CHASSIS
USER’S MANUAL

--
1
Copyright Notice
This document and product is copyrighted, October 1998, by ICP Electronics Inc. All
rights are reserved. No part of this manual may be reproduced, copied, or translated
without prior notice to ICP Electronics Inc.
The information provided in this document is for reference only. We do not assume
any responsibility arising out of the application of the products. This manual is
subject to change without any notice.
PAC-170, ICP are trademark of ICP Electronics Inc.

--
2
Table of Contents
Chapter 1 Product Information
1.1 General Information
1.2 Product Specifications
1.3 Dimensions
Chapter 2 System Setup
2.1 Front Panel of PAC-170
2.2 Rear Panel of PAC-170
2.3 Removing the chassis cover
2.4 The Backplane and Card Clamp Installation
2.5 Disk Drives Installation
2.6 Replacing the Filter
2.7 Power Supply Installation
2.8 Fan Installation
Appendix A Passive Backplane
Appendix B Exploded Diagram

--
3
Chapter 1 Product Information
1.1 General Information
PAC-170 IPC chassis is a rugged PC/AT compatible computer designed for the
factory floor and other Industrial harsh environment.PAC-170 features 7 slots
Passive Backplanes and high reliability AC Input Power Supply ACE-925A.
The chassis can easily be mounted on panels or walls with the supplied brackets.
1.2 Product Specifications
General specification
- Construction :Heavy-duty steel
- Disk Drive :One 3.5”FDD, One 5.25”CD-ROM and Two 3.5”HDDs
- Indicator :Two LEDs to monitor the status of HDD and Power Supply
- Dimension :193 x 432 x 254 mm ( WxDxH )
Passive Backplanes (Optional)
BP-7S 7-slot ISA-bus Backplane
IP-7S 7-slot PCISA-bus Backplane
PCI –7S 7-slot ISA/PCI Backplane
Power Supply
Standard equipped power supply for the PAC-170 is : ACE-925A

--
4
Working Environment
- Operating Temperature :0~50°C
- Relative Humidity :5~95% Relative
- Vibration :5-17Hz, 0.1”double amplitude displacement
17-640Hz, 1.5G acceleration peak to peak
- Shock :10G acceleration peak to peak
- Safety approval :meet CE, FCC
- Shipping Weight :10Kgs
Cooling Fan
One ball bearing fan for system cooling
Drive Capacity
Supports one 3.5”FDD,one 5.25”CD-ROM, two 3.5”HDDs

--
5
1.3 Dimensions
412.00mm
432.00mm
400.00mm 360.00mm
334.00mm
310.00mm
286.00mm
260.00mm
210.00mm D10
D5
R2.5
193.00mm
254.00mm
230.00mm

--
6
Chapter 2 Installation Procedure
The following set up procedures are provided to assist you in installing the system
unit, please follow the steps below:
2.1 Front Panel of PAC-170
RESET
POWER
H.D.D-LED
POWER-LED
SWITCH
SWITCH
KEYBOARD

--
7
2.2 Rear Panel of PAC-170
AC-INPUT
AC-OUTPUT

--
8
2.3Removing the chassis cover
The cover is mounted by six screws on the top of the chassis, remove them
and slide the cover to the rear of the chassis. Figure below shows how to
remove the chassis cover.
Step 2
Step 1

--
9
2.4Backplane Installation
Figure below illustrates how to install the backplanes on the PAC-170

--
10
Step 1
Step 2

--
11
2.5Disk Drives Installation
1.Remove the disk drive bay
2.Mount the drive rails on the front of HDD or FDD
2.Attach the FDD to the bracket with four screws and connect FDD cable
& power cable to the FDD.
3.Attach the HDD to the bracket with four screws and connect a 40-pin flat
cable & power cable to the HDD.

--
12
Step 1
Step 2

--
13
2.6 Replacing the Filter
The filter of the PAC-170 is located at the front end of the chassis. Under
continuous use, the filter should be removed about once a mounth. To replace
the filter, open and close the door by press . Take out the old filter and slide the
new one into place . Then close and lock the filter door.
Press

--
14

--
15
2.7 Power Supply Installation
P9 P8
P8
ACE-925A
POWER
SUPPLY
Brown
Blue
White
Black
Brown
Blue Black
White
17
P9
POWER
SWITCH
GND
BACKPLANE

--
16
2.8 Fan Installation
ACE-925A
POWER
SUPPLY
GND (BLACK)
+12V (RED)

--
17
APPENDIX A PASSIVE BACKPLANES
mm
mm
mm mm
mm mm mm
mm mm
0.00
18.00
175.00
165.00
mm
mm
0.00
10.00
19.30
0.00
97.00
142.50
150.00

--
18
APPENDIX B EXPLODED DIAGRAM